ZTE Z917 Ufi User Manual User Guide

ZTE Corporation Ufi User Guide

Contents

User Guide

Download: ZTE Z917 Ufi User Manual User Guide
Mirror Download [FCC.gov]ZTE Z917 Ufi User Manual User Guide
Document ID2874589
Application IDAMXJFBpmJO1AE7C37haR2g==
Document DescriptionUser Guide
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize21.35kB (266887 bits)
Date Submitted2016-01-15 00:00:00
Date Available2016-07-13 00:00:00
Creation Date2017-08-24 23:27:03
Producing SoftwareGPL Ghostscript 9.18
Document Lastmod2017-08-24 23:27:03
Document TitleUser Guide
Document CreatorAdobe InDesign CS6 (Windows)

GETTING TO KNOW YOUR
MOBILE HOTSPOT
ON/OFF switch
WPS key
LED
indicators
micro-SIM card slot Charging & USB port
Part
Description
ON/OFF
switch
Slide it to turn on/off the
Hotspot.
micro-SIM
card slot
Install the micro-SIM card
(included).
WPS key
When the Wi-Fi function is
enabled, hold it for more than
3 seconds to activate the
WPS function.
LED
indicators
Charging/
USB port
It shows the signal strength,
battery, Wi-Fi and message.

Charge your device.

Connect the client to your
device via USB cable.
Reset point
Insert a pin and hold it for 3 seconds to reset
your device.
INDICATORS
When the Hotspot is powered on, the following
icons will light up. For a description of the
icons, refer to the following table.
Indicator
Status
Description
Limited or no service,
no SIM card or SIM
Red solid card error, registered
to the LTE/UMTS/
HSPA network.
Registered to the
UMTS or HSPA
network and
connected to UMTS
or HSPA network.
Network
Green
solid
Registered to
LTE network and
Blue solid
connected to LTE
network.
SMS
You have unread
Blue solid messages or FOTA
(new software).
Blue
blinking
Your inbox is full or
FOTA upgrading.
LED light No unread messages
off
or no new messages.
Blue solid Wi-Fi is on.
Wi-Fi
Blue
blinking
WPS is active.
LED light
Wi-Fi is off.
off
The battery is low.
(From 10% to dead)
Red solid
Please charge the
battery.
Battery
Green
blinking
The battery is being
charged.
The battery level is
middle or high. (From
100% to 11%)
Green
solid
LED light The battery is not
off
inserted.
SET UP YOUR MOBILE
HOTSPOT
1. Lift SIM card cover.
2. Install SIM card.
3. Power on.
Slide to turn on
Charge your Mobile Hotspot
You can charge your Mobile Hotspot by using
the charger included in the box or by plugging
it into your computer using the USB cable.
Install the battery
1. Remove the cover.
2. Install the battery.
CONNECT & GO
Connect your Wi-Fi device to your
Mobile Hotspot
1. Power on your Mobile Hotspot.
2. On your computer or other Wi-Fi enabled
device, search for available Wi-Fi Networks
and select the default Network Name
(SSID) for your Mobile Hotspot.
Note:
You can view the label on the device to get the
default Wi-Fi SSID and password.
3. Enter the default password and click OK.
4. Open a web browser and go to
www.T-Mobile.com/ConnectMe
Simply follow the on-screen instructions
to set up your No Annual Contract data
service.
Note: Service or use is your agreement to
T-Mobile’s Terms and Conditions. T-Mobile
requires ARBITRATION of disputes
UNLESS YOU OPT-OUT WITHIN 30 DAYS
OF ACTIVATION. See T-Mobile’s Terms and
Conditions for details at www.T-Mobile.com/

terms-conditions.
USE THE WPS
If your client device supports WPS, you don’t
have to input the password manually after WPS
has been available. Please do the following
steps:
1. Power on your Mobile Hotspot and enable
the Wi-Fi function.
2. Press and hold the WPS key on your
device for more than 3 seconds to start
Wi-Fi Protected Setup authentication
process.
3. Enable the WPS function on your client to
respond to this authentication process.
4. Follow the system prompts on your client
to inish the connection.
NOTE: For the detailed operations about the
client, please refer to the client’s instruction.
MANAGING YOUR MOBILE
HOTSPOT
10
Access T-Mobile 4G LTE Mobile
Hotspot
You can access your 4G LTE HotSpot device
information, using an Internet browser
To access using a browser, do the following:
1. Connect to your hotspot device via Wi-Fi
using the network connection software on
your computer. Provide the Wi-Fi network
password, if requested.
2. Open a browser and enter
http://Mobile.Hotspot in the address bar.
The T-Mobile 4G LTE Mobile Hotspot login
screen appears.
3. Enter your Password in the ield provided.
The default password is admin.
4. Select the Save Password checkbox if
you wish to bypass the login screen in the
future.
5. Click Login. If you entered the correct
password, the Dashboard screen appears.
11
To access via USB cable, do the following:
1. Connect your hotspot device to the PC with
USB cable.
2. Power on your device.
3. The OS detects and recognizes new
hardware and inishes the installation
automatically. After successful installation,
the icon
4.
5.
6.
7.
will appear on your desktop.
Note: If the system does not launch
installation automatically, you can run
the installation program in path of My
Computer > Mobile Hotspot.
Double click the icon to open the login
screen.
Enter your Password in the ield provided.
The default password is admin.
Select the Save Password checkbox if
you wish to bypass the login screen in the
future.
Click Login. If you entered the correct
password, the Dashboard screen appears.
12
Change Mobile Hotspot Admin
Password
1.
2.
3.
4.
Access http://Mobile.Hotspot.
Click Settings in the navigation area.
Select the Device Settings tab.
Follow steps under Account Management
to update your Password.
5. Click Apply. If everything is entered
correctly, the Admin Password Changed
dialog appears indicating the password
was successfully changed.
Change Mobile Hotspot Network
Name (SSID)
1.
2.
3.
4.
Access http://Mobile.Hotspot.
Click Settings in the navigation.
Select the Wi-Fi Settings tab.
Change the name that appears in the
Network Name (SSID) ield in the Wi-Fi
Settings area.
5. Select or deselect the Broadcast
Network Name checkbox to enable
or disable broadcasting the hotspot’s
Network Name (SSID).
13
6. Click Apply to save your changes on the
Wi-Fi Settings tab of the Settings screen.
Change Mobile Hotspot Wi-Fi
Password
1.
2.
3.
4.
Access http://Mobile.Hotspot.
Click Settings in the navigation area.
Select the Wi-Fi Settings tab.
Change the value that appears in the
Password ield in the SSID area.
5. Click Apply in the SSID area to save your
changes on the Wi-Fi Settings tab of the
Settings screen.
How to use Mobile Hotspot’s Whitelist
Function
Your Mobile Hotspot has whitelist setting
function to effectively prevent the network
attack, when the user turned off this feature,
all user input correct password can access
via Wi-Fi; But when the user turned on this
function, without further to enter the user's
MAC address, all users will not be able to
access the Mobile Hotspot, only those users
whose MAC address in the whitelist can
access.
14
1. Log in the web UI.
2. Select Settings > Wi-Fi Settings >
Allowed Devices.
3. The switch is off by default, all user input
correct password can access.
4. After open the whitelist function, you
need to know the user client’s MAC
address and add to the list, the format is
XX:XX:XX:XX:XX:XX. You can add up to
10 devices if they are all going to connect,
because the Wi-Fi chip can only support 10
devices connected at the same time.
15
5. If you want to remove some users in the
whitelist, that means they are no longer
allowed to connect, click the
button, and then click Yes to remove.
16
ADDITIONAL INFORMATION
Wi-Fi: Capable devices required. Devices
using wireless connections may be vulnerable
to unauthorized attempts to access data and
software stored on the device. Plan data
allotment applies to use by connected devices
sharing Wi-Fi. Use of connected devices
subject to T-Mobile Terms and Conditions.
Mobile Internet Postpaid Data Passes:
Qualifying postpaid plan and qualifying credit
required. SIM Starter Kit may be required.
Passes do not include voice or messaging.
Pass charges will appear on bill statement for
effective date of the pass. May purchase one
add’l pass in same category prior to expiration
of active pass. Partial megabytes rounded
up. Full speeds available up to speciied data
allotment, including tethering then slowed to up
to 2G speeds for remainder of billing cycle. No
domestic or international roaming, unless Pass
is speciically for roaming. Service available
for time/usage amount provided by pass. For
time period, a day is 12 am to 11:59 pm Paciic
Time. Usage applied irst to passes, next to
any applicable promotional data, then monthly
plan allotment.
17
Mobile Internet Pay In Advance Data
Passes: Limited time offer; subject to change.
Not all features available on all devices. SIM
starter kit may be required. Service available
for time period and/or usage amount provided
by Pass. For time period, a day is 12:00 am to
11:59 pm, Paciic Time. Usage rounded up to
the nearest MB each session. Only one Pass
may be active at a time. Account suspended
after 365 days of inactivity. Data only; does not
include voice, messaging or Wi-Fi services.
Domestic only; no roaming. Usage applied irst
to on demand passes, next to free data, then
monthly Mobile Internet allotment.
Device and screen images simulated.
Coverage: Service not available in some
areas. See brochures and Terms and
Conditions (including arbitration provision)
at www.T-Mobile.com, for additional
information, coverage maps, and restrictions
and details. T -Mobile and the magenta color
are registered trademarks of Deutsche Telekom
AG. © 2016 T-Mobile USA, Inc.
18
ADDITIONAL HELP

T-Mobile Hotspot URL:
http://Mobile.Hotspot/
or IP address: 192.168.0.1.

From http://Mobile.Hotspot, click

Get in touch, free of charge: Just dial
611 from your T -Mobile phone or
call 1-877-453-1304. Customer Care
representatives are available from 3 a.m.
to 10 p.m. Paciic time, daily. Automated
account help is available 24 hours a day, 7
days a week.
for help.
19
TCS530100.1
Source Exif Data: 
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.7
Linearized                      : Yes
Encryption                      : Standard V4.4 (128-bit)
User Access                     : Print, Extract, Print high-res
Create Date                     : 2015:12:22 10:24:38+08:00
Creator                         : Adobe InDesign CS6 (Windows)
Modify Date                     : 2016:01:14 16:48:24+08:00
Tagged PDF                      : Yes
XMP Toolkit                     : Adobe XMP Core 4.2.1-c041 52.342996, 2008/05/07-20:48:00
Instance ID                     : uuid:f69b4e91-0021-4896-b7a4-5740364f2ec4
Original Document ID            : adobe:docid:indd:20d53578-a328-11e5-9ebb-8958e79f1d86
Document ID                     : xmp.id:4260F62053A8E51188A6A598ADD32271
Rendition Class                 : proof:pdf
Derived From Instance ID        : xmp.iid:4160F62053A8E51188A6A598ADD32271
Derived From Document ID        : xmp.did:396EA6FD4FA8E51188A6A598ADD32271
Derived From Original Document ID: adobe:docid:indd:20d53578-a328-11e5-9ebb-8958e79f1d86
Derived From Rendition Class    : default
History Action                  : converted
History Parameters              : from application/x-indesign to application/pdf
History Software Agent          : Adobe InDesign CS6 (Windows)
History Changed                 : /
History When                    : 2015:12:22 10:24:38+08:00
Metadata Date                   : 2016:01:14 16:48:24+08:00
Creator Tool                    : Adobe InDesign CS6 (Windows)
Format                          : application/pdf
Producer                        : Adobe PDF Library 10.0.1
Trapped                         : False
Page Count                      : 24
EXIF Metadata provided by EXIF.tools
FCC ID Filing: SRQ-Z917

Navigation menu