ZTE QP 100_A6 1208 Qp100
User Manual: ZTE qp100
Open the PDF directly: View PDF 
.
Page Count: 4
| Download | |
| Open PDF In Browser | View PDF |
100W QP-100 1~3 Output with battery Charger series Features : Universal AC input / Full range Auto switch when power off (UPS function) Built-in constant current limiting circuit Alarm signal for AC OK and Battery low (TTL open collector output or Relay contact output) Protections: Short circuit / Over load / Over voltage Brown-out (Low AC Input Voltage) Battery low protection Battery polarity protection (by Resettable Fuses) Cooling by free air convection High efficiency, long life and high reliability Withstand 2G vibration test All using 105°c long life electrolytic capacitors 3 years warranty QP-100-G MODEL Output Input Output Number DC Voltage Range Rated Current Current Range Rated Power Ripple & Noise (max.) Voltage Adj. Range Voltage Tolerance Line Regulation Load Regulation Setup, Rise Time Hold up Time (Typ.) Voltage Range Frequency Range Efficiency (Typ.) at 230Vac AC Current (Typ.) Inrush Current (Typ.) Leakage Current Over Load Protection Function Environment Safety & EMC Others Note Over Voltage QP-100-GB QP-100-LB CH1 CH2 CH1 CH2 CH3 CH1 CH2 CH1 CH2 CH3 13.8V 13.8V 13.8V 13.8V 5V 27.6V 27.6V 27.6V 27.6V 5V 5.3A 2A 4.2A 2A 3A 2.15A 1.5A 1.6A 1.5A 3A 0~7A --------- 0~6.5A --------- 0~3.2A 0~3.4A --------- 0~3.3A --------- 0~3.2A --------- 100mV --------- 100mV 100mV --------- 100mV --------- 100mV ±1% --------- ±1% --------- ±3% ±0.5% --------- ±0.5% ±0.5% --------- ±1% 100.56W 100.74W 100mV 100.74W CH1:10% 100.56W CH1:10% ±1% --------- ±1% --------- ±0.5% --------- ±0.5% --------- ±0.5% ±0.5% --------- ±0.5% --------- ±0.5% --------- ±1% ±0.5% --------- 800ms, 50ms/230VAC 50ms / 230VAC 90 ~ 264VAC ±3% 800ms, 50ms/115VAC at full load 10ms /115VAC at full load 127 ~ 373VDC (Withstand 300VAC surge for 5sec. Without damage) 47Hz ~ 63Hz 86% 85% 2A /115VAC Cold Start 87% 85% 1.2A / 230VAC 35A / 115VAC 70A / 230VAC For earth <1mA / 264VAC Above 110% rated output power Protection type : Hiccup mode, recovers automatically after fault condition is removed 115% ~ 140% rated output voltage Protection type : latch-off mode Battery cut off 10V±4% AC OK BAT Low Working Temp. Working Humidity Storage Temp., Humidity Temp. Coefficient Vibration Safety Standards Withstand Voltage Isolation Resistance EMI Conduction & Radiation Harmonic Current EMS Immunity MTBF TTL open collector output Dimension (L*W*H)(mm) Packing QP-100-L 20V±5% Relay contact output Battery low voltage <12V±3% TTL open collector output Relay contact output Battery low voltage <22V±3% -20°C ~ +70°C (Refer to output load de-rating curve) 20 ~ 90% RH non-condensing -40 ~ +85°C, 10 ~90% ±0.03%/°C (0 ~ 50°C) on CH1 10 ~ 500Hz, 2G 10min./1 cycle, period for 60 min. each along X,Y,Z axes Meet UL60950-1 / TUV EN60950-1 Approved I/P - O/P : 3KVAC I/P - FG : 1.5KVAC O/P-FG : 0.5KVAC I/P - O/P: 100M Ω / 500VDC EN55022 : 2006+A1:2007 Class B EN61000-3-2 :2006 Class A, EN61000-3-3 : 1995+A1 : 2005 EN61000-4-2,3,4,5,6,8,11; ENV50204; EN55024 123x95x31mm 1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25°C of ambient temperature. 2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47 uf parallel capacitor. 3. Tolerance: includes set up tolerance, line regulation and load regulation. 4. Line regulation is measured from low line to high line at rated load. 5. Load regulation is measured from 0% to 100% rayed load. 6. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets EMC directives. 7.Length of aet up time is measured at cold first start. Turning ON/OFF the power supply very quickly may lead to increase of the set up time. REV. A6 10/12/08 1 100W QP-100 1~3 Output with battery Charger series Mechanical Specification Unit:mm 123 5 4 5.5 5 CN1 0.2 1 2 3 95 6.65 4 5 6 8.25 7 CN2 1 6.5 3.9 8 CN2 9 0.4 6.5 103.9 3 31 19.1 QP-100-G/L Alarm output Connector(CN2): JST B3B-XH or equivalent Terminal Pin No. Assignment(CN1) Pin No. Assignment 1 AC OK Pin No. Assignment Pin No. Assignment 2 BAT LOW 1 AC/L 5 DC output V+ 3 G (13.8V/20mA) L (27.6V/20mA) 2 AC/N 6 BAT+ 3 FG 7 BAT- 8 DC/DC Output +5V (GB/LB only) DC Output com 4 Mating Housing JST XHP-3 or equivalent Terminal JST SXH-001 T-P0.6 or equivalent QP-100-GB/LB Alarm output Connector(CN2): JST B4B-XH or equivalent Assignment Pin No. 1 2 Mating Housing Terminal JST XHP-4 or equivalent JST SXH-001 T-P0.6 or equivalent AC OK 3 4 Bat. Low Mechanical Specification Output Derating VS Input Voltage Ta=25 100 100 90 80 80 70 LOAD (%) LOAD (%) 60 40 20 -20 0 10 20 30 35 40 50 AMBIENT TEMPERATURE ( 60 ) 70 (HORIZONTAL) 60 50 40 90 95 100 115 120 140 160 180 200 220 240 264 INPUT VOLTAGE (VAC) 60Hz REV. A6 10/12/08 2 100W 1~3 Output with battery Charger QP-100 series For QP-100-G/L Block Diagram AC OK ALARM CIRCUIT EMI FILTER I/P RECTIFIER & FILTER Bat. Low V+ RECTIFIERS & FILTER POWER SWITCHING COM B+ FG DETECTION CIRCUIT PWM CONTROL O.L.P. O.V.P. B- Battery Charger & Back up Control Alarm Signal for AC OK and Battery Low (1) Alarm Signal is sent out through " AC OK " & " Battery Low " pins. (2) An external voltage source is required for this function. The maximum applied voltage is 50V and the maximum sink current is 30mA. (3) Table3.1 explain the alarm function built-in the power supply Function AC OK Battery Low Output of alarm Description The signal is "Low" when the power supply Low turns on (0.3V max. at 30mA) The signal turns to be "High" when the power High or open(External applied supply turns OFF voltage 30mA max.) The signal is "Low" when the voltage of Low battery is under G:12V , L:22V (0.3V max. at 30mA) The signal is "High" when the voltage of High or open(External applied battery is above G:12V , L:22V voltage 30mA max.) Table 3.1 Explanation of Alarm Signal AC OK (Battery low) V+ CN2 Pin3 G: 13.8V/20mA L: 27.6V/20mA CN2 Pin1(Pin2) CN2 Pin3 R V CN1 Pin4 DC output com Internal circuit of AC OK (Battery Low) or CN2 Pin1(Pin2) External voltage and R (The max. Sink is 30mA and 50V) REV. A6 10/12/08 3 100W 1~3 Output with battery Charger QP-100 series For QP-100-GB/LB Block Diagram ALARM CIRCUIT & SWITCHING FILTER I/P EMI FILTER RECTIFIER & FILTER AC OK Bat. Low +5V V+ RECTIFIERS & FILTER POWER SWITCHING COM B+ FG DETECTION CIRCUIT O.L.P. PWM CONTROL O.V.P. B- Battery Charger & Back up Control Alarm Signal for AC OK and Battery Low (1) Alarm Signal is sent out through " AC OK " & " Battery Low " pins. (relay contact type) (2) An external voltage source is required for this function. The maximum applied voltage is 30V and the maximum sink current is 1 A. (3) Table 4.1 explain the alarm function built-in the power supply AC OK(Battery low) Function Description The signal is "Low" when the power supply AC OK turns on High or open(External applied supply turns OFF voltage 1A max.) battery is under GB:12V , LB:22V CN2 Pin1(Pin3) Low or short The signal turns to be "High" when the power The signal is "Low" when the voltage of Battery Low Output of alarm Low or short The signal is "High" when the voltage of High or open(External applied battery is above GB:12V , LB:22V voltage 1A max.) Table 4.1 Explanation of Alarm Signal Externalvoltagesource(V) andresistor(R) (Themax.Sinkis1A and30V) lnternalcircuitof AC OK(BatteryLow) CN2 Pin2(Pin4) REV. A6 10/12/08 4
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : Yes Encryption : Standard V2.3 (128-bit) User Access : Print, Print high-res XMP Toolkit : Adobe XMP Core 4.0-c321 44.398116, Tue Aug 04 2009 14:24:39 Creation Date--Text : Producer : Corel PDF Engine Version 3.0.0.739 Mod Date--Text : Format : application/pdf Creator : esther Title : QP-100_A6 1208 Creator Tool : CorelDRAW Modify Date : 2010:12:09 10:42:53+08:00 Metadata Date : 2010:12:09 10:42:53+08:00 Document ID : uuid:73b69d5d-3344-4bcb-8b15-295155486ca7 Instance ID : uuid:8ade7d8a-ddaa-43c3-93e5-e4c9050cd17a Page Count : 4 Create Date : D:20101208064622 Author : estherEXIF Metadata provided by EXIF.tools