Zalman Tech TNN350APF-V1 SMPS User Manual TNN350APF V1 UserMan
Zalman Tech Co., Ltd. SMPS TNN350APF V1 UserMan
Users Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 559852 |
| Application ID | AVE70+rdyNzmUKgK7iouYA== |
| Document Description | Users Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 2.11kB (26368 bits) |
| Date Submitted | 2005-07-07 00:00:00 |
| Date Available | 2005-07-06 00:00:00 |
| Creation Date | 2005-07-01 15:40:22 |
| Producing Software | Acrobat Distiller 5.0.5 (Windows) |
| Document Lastmod | 2005-07-01 15:40:40 |
| Document Title | TNN350APF-V1 UserMan.xls |
| Document Creator | Acrobat PDFMaker 5.0 for Excel |
| Document Author: | KIM J.S |
1. INTRODUCTION
The "TNN350APF-V1" is a Power Supply designed to be used "ATX12V" form factor
server computer systems
1.1 SCOPE
The scope of this document is limited to the requirements of "ATX12V" PC form
factor switching Power Supply. Especially, It is applied to the line input capability,
remote ON/OFF, cooling, standby voltage("VSB") and electrical characteristics.
Form-factor
ATX/ATX12V
380. Watt max peak
POWER
350. Watt max Continuous
80% at Full load
Efficiency
Output
voltage
Requla
-tion
Min load(Amps)
Max load(Amps)
Peak current(Amps)
+12VDC1
5%
1A
10.0A
18
+12VDC2
5%
1A
15.0A
+5VDC
5%
0.5A
20.0A
+3.3VDC
5%
0.5A
20.0A
-12VDC
5%
0A
0.3A
+5VSB
5%
0A
2.0A
2.5A
2. ELECTRICAL SPECIFICATION
2.1 AC INPUT LINE REQUIREMENTS
Parameter
MIN
NOM
MAX
UNIT
Vin(115VAC)
90
115
135
VACrms
Vin(230VAC)
180
230
265
VACrms
Vin FREQUENCY
47
63
Hz
Vin(115VAC)
15
Vin(230VAC)
MODEL NO: TNN350APF-V1 REV.0
DATE: 2005. 1. 17
ZALMAN SPECIFICATION
PAGE: 1/9
2.1.1 INRUSH CURRENT
Max. inrush current shall not exceed 60 CA(Peak to Peak).
2.2 DC OUTPUT REQUIREMENTS
2.2.1 OUTPUT REQUIREMENTS
TEST POINT : OUTPUT CONNECTOR LOAD TERMINALS.
Parameter
MIN
NOM
MAX
UNIT
+12VDC1
+11.4
+12.00
+12.6
Volts
+12VDC2
+11.4
+12.00
+12.6
Volts
+5VDC
+4.75
+5.00
+5.25
Volts
+3.3VDC
+3.14
+3.30
+3.47
Volts
-12VDC
-10.80
-12.00
-13.20
Volts
+5VSB
+4.75
+5.00
+5.25
Volts
2.2.2 DC output CURRENT
1) Maximum continuous total DC output power shall not exceed 350Watts.
2) Maximum +5V and +3.3V output power shall not exceed 120Watts.
3) Maximum Peak Total DC output power shall not exceed 380Watts.
4) It shall not exceed 17 seconds in duration at Total +12VDC1, +12VDC2
output power, 300Watts.
5) Output voltage of +5VSB shall be maintained within the power shut down.
Range
Parameter
MIN
NOM
MAX
Range 1
+12VDC1
1.0
8A
Amps
+12VDC2
1.0
12A
(Normal
+5VDC
0.5
10A
Load)
+3.3VDC
0.5
14.1A
-12VDC
0.0
0.3
+5VSB
0.0
2.0A
+12VDC
1.0
5A
Amps
+12VDC
1.0
9A
(High
+5VDC
0.5
3A
Load)
+3.3VDC
0.5
5A
-12VDC
0.0
0.3
+5VSB
0.0
2A
Range 2
PEAK
2.5A
2.5A
MODEL NO: TNN350APF-V1 REV.0
DATE: 2005. 1. 17
ZALMAN SPECIFICATION
PAGE: 2/9
UNIT
2.2.3 EFFICIENCY
1) The power supply at full load provide AC/DC conversion efficiency 80% minimum.
2.2.4 OUTPUT RIPPLE/NOISE
. The measurements should be made by crossing a 10uF electrolytic capacitor and
a 0.1uF Ceramic capacitors at each output with measuring band width from DC to
20MHz.
MAX
UNIT
80
mVp-p
1.0%
80
+3.3VDC
1.0%
80
-12VDC
1.0%
120
+5VSB
1.0%
50
Parameter
Range
MIN
+12VDC
1.0%
+5VDC
NOR
10uF
V OUT
0.1uF
AC LIVE
AC INPUT
LOAD
PSU
AC NEUTRAL
V return
SCOPE
AC GROUND
2.2.5 Dynamic Loading
. Load Slew Rate : 0.5A/us
Output
Step Load Size
Load Slew Rate
Capacitive Load
+3.3V
30% of max load
0.5A/us
1000uF
+5V
30% of max load
0.5A/us
1000uF
+12V1,+12V2
65% of max load
0.5A/us
1000uF
+5VSB
25% of max load
0.5A/us
1uF
MODEL NO: TNN350APF-V1 REV.0
DATE: 2005. 1. 17
ZALMAN SPECIFICATION
PAGE: 3/9
2.3 TIMING / HOUSE KEEPING
PS_ON
PS_OFF
DC Enable
95%
10%
PWR-OK
T2
T4
T3
* PW-OK sense level : 95% of nominal
2.3.1 REMOTE ON/OFF CONTROL
The power supply DC outputs (with the exception of +5VSB) shall be enabled with
an active-low, TTL-compatible signal("PS-ON"). The +5VSB is on whenever the
AC power is present.
. When PS-ON is pulled to TTL low, the DC outputs are to be enabled.
. When PS-ON is pulled to TTL high or open circuited, the DC outputs are
to be disabled. Turn ON/OFF delay >- 1000ms
2.3.2 POWER UP DELAY
The output voltages shall rise from <10% of nominal to within the regulation ranges
specified in sec 2.2.1 within 5 to 70ms.
MODEL NO: TNN350APF-V1 REV.0
DATE: 2005. 1. 17
ZALMAN SPECIFICATION
PAGE: 4/9
2.3.3 POWER GOOD SIGNAL, POK
. Signal Type : Open Collector +5VDC, TTL compatible.
. Logic level Low : <0.4V 4mA
. Logic level High :Between 2.4VDC and 5VDC output while sourcing current, 2mA
. POK Delay : 200mS 20 -> 500 -> 5Hz
. Acceleration :0.02G
. Airection : X, Y, Z
. Period : 6 Minutes
. Cycie : 10
2.4.16. ACOUSTIC NOISE
. The power Supply Must not generate Acoustic Noise in excess of 30dB at a
Distance of 1 Meter from any Point on The requirments Surface.
2.4.18. AC LINE NOISE
. The Power Supply Shall Operate Normally When AC Line Noise is Applied
. Noise Crest Value : 1000VAC
. Polarity : +, . Pulse Width : 1us
. Phase : 0 - 360
. Mode : Common, Normal
. Time : 3Minutes
MODEL NO: TNN350APF-V1 REV.0
DATE: 2005. 1. 17
ZALMAN SPECIFICATION
PAGE: 7/9
2.5. DC CONNECTOR REQUIVEMENTS
2.5.1 BASE BOARD CONNECTOR
PS-1 Connector : MOLEX 39-01-2240 or equivalent
Pin
Signal
Pin
Pin
Signal
Wire Color
+3.3VDC
Orange
13
+3.3VDC
Orange
+3.3VDC
Orange
sense
Brown
14
-12VDC
Blue
COM
Black
sense
Black
15
COM
Black
+5VDC
Red
sense
Red
16
PS-ON
Green
COM
Black
sense
Yellow
17
COM
Black
+5VDC
Red
18
COM
Black
COM
Black
19
COM
Black
POK
Gray
20
+5VSB
Violet
21
+5VDC
Red
10
+12VDC
Yellow
22
+5VDC
Red
11
+12VDC
Yellow
23
+5VDC
Red
12
+3.3VDC
Orange
24
COM
Black
. 18AWG is suggested for all wire except for the 3.3V sense return wire, pin 13
(22AWG) For 300W configurations, 16AWG is recommended all 12VDC, +5VDC,
+3.3VDC, and COM
Processor Power Connector : MOLEX 39-01-2080 or equivalent
Pin
Signal
Wire Color
Pin
Signal
Wire Color
COM
Black
+12DC1
Yellow
COM
Black
+12DC1
Yellow
COM
Black
+12DC1
Yellow
COM
Black
+12DC1
Yellow
Pin
Signal
Wire Color
Pin
Signal
Wire Color
COM
Black
+12DC2
Yellow
COM
Black
+12DC2
Yellow
COM
Black
+12DC2
Yellow
COM
Black
+12DC2
Yellow
2.5.2. PERIPHERAL CONNECTORS
. PA
MODEL NO: TNN350APF-V1 REV.0
DATE: 2005. 1. 17
ZALMAN SPECIFICATION
PAGE: 8/9
. Connector : AMP 1-480424-0 or Molex 8981-04P or equivalent.
. Contacts : AMP 61314-1 terminals or equivalent.
Pin
Signal
Wire Color
+12VDC1
Yellow
COM
Black
COM
Black
+5VDC
Red
. PB(Floppy Drive Connector)
. Connector : AMP 171822-4 or equivalent.
Pin
Signal
Wire Color
+5VDC
Red
COM
Black
COM
Black
+12VDC1
Yellow
.+12V Power Connector
3. MECHANICAL
3.1. PHYSICAL DIMENSION
Dimension : L * W * H mm
294*200*67
3.2. LABELING /MARKING
MODEL NO: TNN350APF-V1 REV.0
DATE: 2005. 1. 17
ZALMAN SPECIFICATION
PAGE: 9/9
FCC Compliance Statement
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1)This Device may not cause harmful interference, and
(2) This device must accept any interference received,
including interference that may cause undesired operation.
Caution : Any changes or modifications in construction of this device which are not expressly
approved the party responsible for compliance could void the user's authority to operate the
equipment.
NOTE : This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications, However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
- Consult the dealer or an experienced radio/TV technician for help.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.3 Linearized : No Modify Date : 2005:07:01 15:40:40+09:00 Create Date : 2005:07:01 15:40:22+09:00 Page Count : 10 Creation Date : 2005:07:01 06:40:22Z Mod Date : 2005:07:01 06:40:22Z Producer : Acrobat Distiller 5.0.5 (Windows) Author : KIM J.S Metadata Date : 2005:07:01 06:40:22Z Creator : KIM J.S Title : TNN350APF-V1 UserMan.xls Page Mode : UseNoneEXIF Metadata provided by EXIF.tools