Zebra Technologies 640I-UHF card Printer User Manual

Zebra Technologies Corporation card Printer Users Manual

user manual -2

Download: Zebra Technologies 640I-UHF card Printer User Manual
Mirror Download [FCC.gov]Zebra Technologies 640I-UHF card Printer User Manual
Document ID1219812
Application IDgi7o8WR1GNE8S2uRG/yV4A==
Document Descriptionuser manual -2
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize324.35kB (4054343 bits)
Date Submitted2009-12-28 00:00:00
Date Available2009-12-28 00:00:00
Creation Date2009-12-28 16:33:11
Producing SoftwareAcrobat Distiller 9.2.0 (Windows)
Document Lastmod2009-12-28 16:33:17
Document TitleUsers Manual
Document CreatorFrameMaker 8.0
Document Author: rringwald

Installation
Installation Procedure
Attaching the Ribbon Take-Up Spool
Step 1. Attach the Ribbon Take-Up Spool by sliding it onto the Ribbon Take-Up Spindle and
pressing it straight back until in clicks into place.
Important • Make sure that the Ribbon Take-Up Spool is attached with its “toothed” end
toward the rear of the printer.
The two figures below show the right and wrong ways to insert the printing ribbon on
either spindle.
Right way: the clip is OVER the core.
14
Wrong way: the core is not pushed fully against
the back side, resulting in a Y border on the
printed cards.
Zebra P630i & P640i Card Printer User’s Manual
980541-003 Rev. B
Installation
Installation Procedure
Installing the Ribbon
i Series Printers require the use of i Series ribbons for full color printing. These Resin Thermal
Transfer and Dye Sublimation ribbons are specifically designed for the i Series Printers.
Note • In normal printer operation, when the ribbon is exhausted, a warning message appears
on the monitor and the MEDIA indicator on the printer lights.
Step 1. Open the printer Main Cover. The printhead will raise for easy ribbon loading.
Step 2. If present, remove the used Supply and Take-Up Spools.
Step 3. Remove the ribbon from its packaging. Remove the tape that holds the end of the
ribbon (save this tape; it will be used shortly).
Step 4. Install the Ribbon on the left (supply) spindle, with the free end of the ribbon coming
from the roll pointing down to your right.
Note • Note that the “flanged” end of the ribbon spool is toward the rear of the printer, and
make sure the internal grooves on the core engage the teeth on the supply spindle.
980541-003 Rev. B
Zebra P630i & P640i Card Printer User’s Manual
15
Installation
Installation Procedure
Step 5. Route the Ribbon as shown in the figure below. The Ribbon Supply Spindle is freewheeling; pull ribbon off it as needed. If the tape removed from the new ribbon in
step 3 is undamaged, use it to attach the end of the ribbon to the Take-Up Spool;
otherwise use other adhesive-backed tape.
Important • When the end of the ribbon is attached to the Take-Up Spool, slack in the ribbon
can be taken up by rotating the Ribbon Supply Spool; do not try to turn the Take-Up Spool.
4. Run the
ribbon up
and to
the right,
around the
spool
Ensure the
ribbon is
centered
on the
spool
1. Pass the
ribbon over
the round
guide bar
Attach the
ribbon with
tape
2. Ribbon goes
through the
Sensor
3. Ribbon goes
under the
Printhead
Step 6. Close the printer Main Cover. Press the RIBBON button on the Control Panel to
synchronize the color ribbon. If the MEDIA light fails to go out, check the
Ribbon Sensor.
Caution • Color ribbon wrinkling and “fold-over” can seriously affect print quality
Step 7. Re-open the printer cover to inspect the ribbon path for wrinkles and folds. Correct if
necessary, then close the cover. If you do not then hear the ribbon motor advancing
the ribbon, press the RIBBON button.
16
Zebra P630i & P640i Card Printer User’s Manual
980541-003 Rev. B
Installation
Installation Procedure
Installing the Cleaning Cassette
Before being printed, each surface of the card is cleaned by a soft tacky roller that is itself
cleaned periodically by adhesive tape in the Cleaning Cassette. By default, the roller is cleaned
every 10 cards. The printer driver software allows the card count to be modified.
By cleaning the roller every 10 cards, the Cleaning Cassette contains sufficient tape
for 3,000 cards.
Step 1. Open the main cover of the printer.
Step 2. If present, remove the used Cleaning Cassette.
Step 3. Remove the Cleaning Cassette from its packaging.
Step 4. Remove the protective foil from the Cleaning Cassette. Avoid touching the exposed
tacky surface.
Step 5. Install the Cleaning Cassette on the printer by locating the rectangular pin on the
cleaning mechanism in the receptacle on the cassette. Push the cassette gently home,
ensuring that the internal grooves on the upper spool engage the teeth on the take-up
drive; you will hear a click when it is fully engaged. Note that you may need to move
the take up side of the cleaning tape assembly to allow for full engagement.
980541-003 Rev. B
Zebra P630i & P640i Card Printer User’s Manual
17
Installation
Installation Procedure
Loading the Laminate
Note • In this description of loading laminate, references to the lower Laminate Cassette
apply only to the P640i Printer. The P640i Printer can apply laminate to both surfaces of the
card; the P630i Printer only to the upper surface.
The Laminate (laminating film) is loaded into cassettes to protect it from dirt or other
contaminants.
See the figure below. The “Upper Laminate Cassette”, used on both the P630i and P640i
Printers, has a label with the word “UPPER” and another “label” of a red dot. The “Lower
Laminate Cassette”, used only on the P640i Printer, has a label with the word “LOWER” and
another “label” of a yellow dot.
“Upper
Laminate
Cassette”
(P630i and
P640i)
“Lower
Laminate
Cassette”
(P640i only)
18
Zebra P630i & P640i Card Printer User’s Manual
980541-003 Rev. B
Installation
Installation Procedure
Removing the Laminate Cassette(s)
Step 1. The Laminate Cassette(s) (Upper only for the P630i Printer; Upper and Lower for the
P640i) are held in position by latch plates. The Upper Cassette is freed by turning its
Latch Plate counter-clockwise to a full vertical position; the Lower Cassette (only
present on the P640i Printer) is freed by turning its Latch Plate clockwise. Then pull
the cassette straight out from its holder.
Upper Laminate
Cassette Latch Plate
(P630i and P640i)
Heater
Cores
area
Lower Laminate
Cassette Latch Plate
(P640i only)
Hot Surface • If the printer has been in use, the Heater Cores area of the Laminator
may be hot.
Important • If either Latch Plate is opened, even unintentionally, the corresponding Cassette
must be removed and the Laminate reeled in.
Caution • If you feel resistance when removing the cassette, the laminate has likely run
out, leaving one end attached to the core and the other end under the cutter. Keep
tugging on the cassette, which will come free with a short tail of laminate.
980541-003 Rev. B
Zebra P630i & P640i Card Printer User’s Manual
19
Installation
Installation Procedure
Step 2. If there is a suspicion a patch is blocked somewhere, temporarily remove the
corresponding Transfer Guide to be sure there are no scraps of laminate remaining. If
there are any, remove them. Then slide the Transfer Guide back in until it is held in
place by the Retaining Spring.
1. Push and hold
the Retaining
Springs (A)
to the Left
(B)
2. Slide the
Transfer
Guides (B)
Straight Out
(A)
(A)
3. Release the
Retaining
Springs (A)
(B)
Step 3. Open the Cassette, like a clam shell, by separating its two halves. Grasp the two
halves firmly with your fingers, then pull it apart. Do NOT use tools. (Upper
Cassette shown.)
Step 4. If there is an empty laminate core in the Cassette, remove it.
20
Zebra P630i & P640i Card Printer User’s Manual
980541-003 Rev. B
Installation
Installation Procedure
Loading the Laminate Cassette(s)
Important • If you are using partial-width laminate in the Lower Cassette of a P640i Printer,
read the following section, Using Partial-Width Laminate, before proceeding with this
procedure. (Partial-width laminates are frequently used on the bottom surface of cards that
have a signature panel or a magnetic stripe.)
Important • The Upper and Lower Laminate Cassettes (the lower one only used on the P640i
Printer; the upper one used on both printers) are loaded differently, even though the Cassettes
appear virtually the same.
Note • Handle the laminate by the ends of the spools to avoid contaminating the laminate.
Step 1. Remove the new roll of laminate from its packaging.
Step 2. Carefully following the guidelines in the following figure, place the laminate in
the Cassette.
Upper Cassette
(Used on Both P630i and P640i)
White Roller Up
Notched End of
Spool to Left
Laminate Unrolls
Under Spool
Labels inside
Cassettes
showing notch
orientation
Laminate Unrolls
Over Spool
Notched End of
Spool to Right
White Roller Down
Lower Cassette
(Used on P640i Only)
980541-003 Rev. B
Zebra P630i & P640i Card Printer User’s Manual
21
Installation
Installation Procedure
Step 3. Pull out an inch or two of laminate past the lip of the cassette.
Step 4. Close the cassette by firmly pressing the “clamshell” together. You will hear a click
and feel a detent when the halves of the cassette seat together.
Step 5. Pull out a little more laminate between the lips of the cassette. If it suddenly stops,
resisting further pulling, a spring detent on the cassette has probably snagged a notch
on the end of the core. This means that the core was installed the wrong way. Open
the cassette and re-install the laminate.
Step 6. If the exposed end of the laminate is uneven or crinkled, cut it as square as you can
with scissors.
Step 7. Holding the cassette with the white roller up and pointing to your left, rotate the core
counter-clockwise to reel in the laminate. Stop when the end of the laminate is even
with the edge of the lips of the cassette.
Important • Check for overhang any time the cassette latch is opened or the cassette is
removed.
22
Zebra P630i & P640i Card Printer User’s Manual
980541-003 Rev. B
Installation
Installation Procedure
Laminating Contact Smart Cards
The laminating patch on the top surface of a smart card has a rectangular aperture to expose
the card’s electrical contacts. In all other respects the laminating process for smart cards is the
same as for ordinary cards. Note that this procedure also applies to registered laminates.
The special laminate for the top cassette is punched with a repeated pattern. Loading
procedure for smart card laminate is exactly the same as for standard laminate.
Note • Check if the patch roll is centered on the core; if not, gently tap the roll on a flat
surface to re-center it.
INDEX
MARKER
CUT
LINE
The smaller hole is an index marker that tells the printer where to cut the laminate, exactly
splitting the index hole (the printer driver allows adjustment of the cut location).
After loading the Smart Card laminate in the upper cassette, trim the laminate along the cut
line as shown above.
Note • When using smart card or registered laminates, the laminate length value in the driver
may need to be adjusted; see Laminator Station Adjustments on page 72..
980541-003 Rev. B
Zebra P630i & P640i Card Printer User’s Manual
23
Installation
Installation Procedure
Using Partial-Width Laminate
Note • Since partial-width laminates are only used for the back (i.e., lower) surface of the
card, this section only applies to the P640i Printer.
Laminate come in three widths:
“Full-Width” laminate is 2 in (51 mm) wide. Full-width laminate is used on the front (i.e.,
upper) or back (i.e., lower) surface of the card.
“Partial-Width” laminate is available in two widths:
•
1.66 in (42mm) wide laminate is used for cards with a writable signature panel.
•
1.33 in (33 mm) wide laminate is used for cards with a magnetic stripe
If there is no signature panel or magnetic stripe on the back of the card, full-width laminate
would generally be used. These are shown in the following figure.
2“
1.66“
BACK OF
FC
CARD
1.3”
Step 1. Remove the Laminate Edge Guide from its “storage location” on the Laminator
Frame (it snaps out).
Laminate
Edge
Guide
24
Zebra P630i & P640i Card Printer User’s Manual
980541-003 Rev. B

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.7
Linearized                      : Yes
XMP Toolkit                     : Adobe XMP Core 4.0-c321 44.398116, Tue Aug 04 2009 14:24:39
Modify Date                     : 2009:12:28 16:33:17-08:00
Create Date                     : 2009:12:28 16:33:11-08:00
Metadata Date                   : 2009:12:28 16:33:17-08:00
Creator Tool                    : FrameMaker 8.0
Format                          : application/pdf
Title                           : _980541_P630i_P640i_UM_Rev_003_B.book
Creator                         : rringwald
Document ID                     : uuid:a7830977-dc49-4fa9-b365-1f59edb40453
Instance ID                     : uuid:df3a484b-697b-41a3-bb46-902e66cba03c
Producer                        : Acrobat Distiller 9.2.0 (Windows)
Page Count                      : 11
Author                          : rringwald
EXIF Metadata provided by EXIF.tools
FCC ID Filing: I28-640I-UHF

Navigation menu