Zebra Technologies MPACTINDR2 MPACT Tag User Manual Regulatory

Zebra Technologies Corporation MPACT Tag Users Manual Regulatory

Contents

Users Manual Regulatory

Regulatory Information
All Zebra devices are designed to be compliant with rules and regulations in locations they are sold and will
be labeled as required.
This regulatory information applies to Model number MPACT-INDR2
Local language translations are available at the following website:
www.zebra.com/support
Any changes or modifications to Zebra equipment, not expressly approved by Zebra, could void the user’s
authority to operate the equipment.
Wireless Device Country Approvals
Regulatory markings, subject to certification, are applied to the device signifying the radio(s) is/are approved
for use in the following countries: United States, Canada and Europe.
Please refer to the Declaration of Conformity (DoC) for details of other country markings. This is available at
www.zebra.com/doc.
Note: Europe includes Austria, Belgium, Bulgaria, Czech Republic, Cyprus, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Liechtenstein, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Slovak Republic, Slovenia, Spain, Sweden, Switzerland and
the United Kingdom.
Operation of the device without regulatory approval is illegal.
Bluetooth Smart® Wireless Technology
This is an approved Bluetooth® product. For more information or to view End Product Listing, please visit
https://www.bluetooth.org/tpg/listings.cfm.
Warnings for use of Wireless Devices
Please observe all warning notices with regard to the usage of wireless devices.
Potentially Hazardous Atmospheres – Vehicles Use
You are reminded of the need to observe restrictions on the use of radio devices in fuel depots, chemical
plants etc. and areas where the air contains chemicals or particles (such as grain, dust, or metal powders) and
any other area where you would normally be advised to turn off your vehicle engine.
Potentially Hazardous Atmospheres – Fixed Installations
You are reminded of the need to observe restrictions on the use of radio devices in fuel depots, chemical
plants etc. and areas where the air contains chemicals or particles (such as grain, dust, or metal powders).
Safety in Aircraft
Switch off your wireless device whenever you are instructed to do so by airport or airline staff. If your device
offers a ‘flight mode’ or similar feature, consult airline staff as to its use in flight.
Safety Information
RF Exposure Guidelines
Reducing RF Exposure - Use Proper
Only operate the device in accordance with the instructions supplied.
International
The device complies with internationally recognized standards covering human exposure to electromagnetic
fields from radio devices. For information on “International” human exposure to electromagnet fields refer to
the Zebra Declaration of Conformity (DoC) at www.zebra.com/doc.
For further information on the safety of RF energy from wireless devices, see www.zebra.com/support.
This is located under Wireless Communications and Health.
Radio Frequency Interference Requirements- FCC
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Consult the dealer or an experienced radio/TV technician for help.
As noted above, this device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
Radio Frequency Interference Requirements - Canada
This device is in compliance with the NRC for Industry Canada applicable to license-exempt radios. Use is
allowed with the following two conditions: (1) the device must not produce interference, and (2) the device
must accept any interference to the radio, even if the interference is likely to compromise operation.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de
licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de
brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d'en compromettre le fonctionnement.
CAN ICES-3(B)/ NMB-3 (B)
Marking and European Economic Area (EEA)
Bluetooth® Wireless Technology for use through the EEA has the following restriction of a maximum radiated
transmit power of 100mW EIRP in the frequency range 2.400 -2.4835 GHz.
European Union Statement of Compliance
Zebra hereby declares that this device is in compliance with the essential requirements and other relevant
provisions of Directive 1999/5/EC and 2011/65/EU. A Declaration of Conformity may be obtained from at
www.zebra.com/doc.
Product Introduction Guide
Part Numbers: GE-MB1000-01-WR,
Customer Support Web Site
If you have a problem with your equipment, contact Support for your region. Support and issue
resolution is provided for products under warranty or that are covered by a service agreement. For
information and online assistance including developer tools, software downloads, product manuals,
support contact information and online repair requests.
When contacting Support, please provide the following information:
• MAC ID of the product shown on the front of the product
• Model number or product name shown on the label on the front of the product.
Batteries
Important: This beacon contains a lithium coin cell type CR2032 battery. This is a non-replaceable battery.
Dispose of batteries in accordance with local governmental regulations. For information on how to remove and
reinsert a battery, see the Hardware Installation Guide available at www.zebra.com/support.
Perchlorate Notice: Zebra beacons ship with Panasonic batteries, which may contain perchlorate. For more
information on perchlorate notifications, see the Panasonic Web site at:
http://www.panasonic.com/industrial/includes/pdf/Prodnotice_CA_Perchlorate_Notice_CR_coin_06-2008.pdf.
Tag Mounts and Installation
For mounting and installation information, refer to the Hardware Installation Guide.
Other Licenses
This logo indicates that this product is licensed to operate according to Apple’s iBeacon specifications.
For ease of installation, peel the red backing tape from the GE-MB1000-01-WR from the round end, as shown in the following:
MN-002822-01
Revision A September 2016

Navigation menu