Zebra Technologies QL320352 Portable Printer User Manual UMAN Q3D

Download:
Mirror Download [FCC.gov]
Document ID	247962
Application ID	hfQ94t4hlqNl4wP0GAZnjg==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	108.99kB (1362320 bits)
Date Submitted	2002-06-07 00:00:00
Date Available	2002-08-05 00:00:00
Creation Date	2002-03-11 12:07:08
Producing Software	Acrobat Distiller 5.00 for Macintosh
Document Lastmod	2002-04-01 09:57:28
Document Title	UMAN-Q3D.pdf
Document Creator	Adobe PageMaker 6.52
Document Author:	Zebra Technologies Corporation, MPCOE, Warwick

UMAN-QL3
Rev.D March, 2002
Proprietary Statement
This manual contains proprietary information of Zebra Technologies Corporation. It is
intended solely for the information and use of parties operating and maintaining the
equipment described herein. Such proprietary information may not be used, reproduced,
or disclosed to any other parties for any other purpose without the expressed written permission of Zebra Technologies Corporation.
Product Improvements
Since continuous product improvement is a policy of Zebra Technologies Corporation, all
specifications and signs are subject to change without notice.
FCC Compliance Statement
NOTE: This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provided
reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual,
may cause harmful interference to radio communications. Operation of this equipment in
a residential area is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
WARNING: Exposure to Radio Frequency radiation. To conform to FCC RF exposure requirements this device shall be used in accordance with the operating conditions and
instructions listed in this manual.
NOTE: This unit was tested with shielded cables on the peripheral devices. Shielded cables must be used with the unit to insure compliance
Changes or modifications to this unit not expressly approved by Zebra Technologies Corporation could void the user’s authority to operate this equipment.
Canadian Compliance Statement
"IC:" before the equipment certification number signifies that the Industry Canada technical specifications were met. It does not guarantee that the certified product will operate to
the user's satisfaction.
Liability Disclaimer
Inasmuch as every effort has been made to supply accurate information in this manual,
Zebra Technologies Corporation is not liable for any erroneous information or omissions.
Zebra Technologies Corporation reserves the right to correct any such errors and disclaims liability resulting therefrom.
No Liability for Consequential Damage
In no event shall Zebra Technologies Corporation or anyone else involved in the creation,
production, or delivery of the accompanying product (including hardware and software)
be liable for any damages whatsoever (including, without limitation, damages for loss of
business profits, business interruption, loss of business information, or other pecuniary
loss) arising out of the use of or the results of use of or inability to use such product, even
if Zebra Technologies Corporation has been advised of the possibility of such damages.
Because some states do not allow the exclusion of liability for consequential or incidental
damages, the above limitation may not apply to you.
Copyrights
The copyrights in this manual and the system described therein are owned by Zebra
Technologies Corporation. All rights are reserved. Unauthorized reproduction of this
manual or the software in any of the system modules may result in imprisonment of up to
one year and fines of up to $10,000 (17 U.S.C.506). Copyright violators may be subject
to civil liability.
All products and brand names are trademarks of their respective companies. All rights
reserved.
©
2002 Zebra Technologies Corporation
ii
QL 320 User’s Guide
Mobile Printer
User’s Guide
Contents
Introduction ........................................... 7
Unpacking and Inspection .......................................... 7
Reporting Damage ..................................................... 7
Getting Ready to Print ............................ 9
Battery ........................................................................ 9
Installing the Battery ...................................................... 9
Charging the Battery ...................................................... 9
Loading the Media .................................................... 10
Installing the Media ...................................................... 10
Operator Controls ..................................................... 13
Standard Keypad .......................................................... 13
LCD Control Panel ....................................................... 15
Verify the Printer Is Working ..................................... 18
Printing a Configuration Label ...................................... 18
Connecting the Printer .............................................. 18
Cable Communications ................................................ 19
IR Communications ...................................................... 20
SRRF Communications ................................................ 21
Zebra SRRF Network Overview ................................... 21
Bluetooth™ Networking Overview ............................... 23
Wireless Local Area Network (WLAN) ......................... 25
Setting Up the Software ............................................ 26
Adjustable Shoulder Strap ........................................ 27
Belt Clip .................................................................... 28
Preventive Maintenance ....................... 29
Extending Battery Life............................................... 29
Cleaning .................................................................... 31
Troubleshooting ................................... 32
Standard Control Panel............................................. 32
Optional LCD Control Panel...................................... 32
Troubleshooting Topics ............................................. 33
Troubleshooting Tests ............................................... 34
Printing a Configuration Label ...................................... 34
Sample Configuration Label ......................................... 35
Communications Diagnostics ....................................... 37
Calling the Help Desk ................................................... 37
Specifications ...................................... 38
Printing Specifications .............................................. 38
Memory/Communications Specifications .................. 38
iv
QL 320 User’s Guide
Label Specifications .................................................. 39
Font/Bar Code Specifications ................................... 39
Physical/Environmental/Electrical Specifications ...... 40
Communications Port ............................................... 41
Agency Approvals ..................................................... 42
Accessories .............................................................. 42
Appendix A .......................................... 43
Interface Cables
Appendix B .......................................... 46
Media Supplies
Appendix C.......................................... 47
Maintenance Supplies
Appendix D .......................................... 48
Product Support
Index ................................................... 49
Patent Information .............................. 51
QL 320 User’s Guide
1
12
11
10
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
Platen Roller
Bar Sensor
Media Support
“EZ-Peel” Peeler
Latch
Latch Release Lever
“D” Rings
Control Panel
QuickLink Module
Print Head
Media Support Disks
15
Media Cover
Belt Clip
Battery
Battery Charging Receptacle
QL 320 User’s Guide
13
14
Introduction
Thank you for choosing our Zebra QL 320 Mobile Printer. This
rugged printer is sure to become a productive and efficient addition to your workplace thanks to its innovative design. Because it’s
made by Zebra Technologies Corporation, you’re assured of
world-class support for all of your bar code printers, software, and
supplies.
• This user’s guide gives you all the information you’ll need to
operate the QL 320 printer.
• The QL 320 uses the CPL programming language. To create and print labels using the CPL language, refer to the
Mobile Printer Programming Guide and our Label Vista™
label creation program.
• The QL 320 has an optional interpreter for the ZPL II® Programming Language which interprets commands up to X.8
firmware. The printer must be equipped with the optional
memory upgrade and appropriate application in order to
use this function. A ZPL II Program Guide (part #46530L)
can be used as reference for the ZPL II label design programming language. If either manual was not ordered with
the printer, simply call your re-seller or Zebra Technologies
Corporation or visit the Zebra web site..
Unpacking and Inspection
Inspect the printer for possible shipping damage:
• Check all exterior surfaces for damage.
• Open the media cover (refer to “Loading the Media” in the
Getting Ready to Print section) and inspect the media compartment for damage.
In case shipping is required, save the carton and all packing
material.
Reporting Damage
If you discover shipping damage:
• Immediately notify and file a damage report with the shipping company. Zebra Technologies Corporation is not responsible for any damage incurred during shipment of the
printer and will not cover the repair of this damage under its
warranty policy.
• Keep the carton and all packing material for inspection.
• Notify your authorized Zebra re-seller.
QL 320 User’s Guide
Battery
Belt Clip
Charger Jack
FIGURE 2
LI72 Charger
Charger Jack
FIGURE 3
QL 320 User’s Guide
Getting Ready to Print
Battery
Installing the Battery
NOTE: Batteries are shipped uncharged. Remove protective shrinkwrap and labels from new battery packs prior to use.
1. If the printer is so equipped, rotate the Belt Clip to allow access to the Battery compartment.
2. Insert the battery into the printer as shown in Figure 2,
3. Rock the Battery into the printer as shown until it locks in
place.
When the battery is first installed, the Control Panel indicators
may briefly turn on and then go off which indicates the battery is
not fully charged (see “Charging the Battery” below and “Operator
Controls”).
Charging the Battery
Refer to Figure 3. Your battery charger may look slightly different from the ones illustrated.
If you are using the LI 72 battery charger:
1. Install the battery in the printer and plug the Charger into
the appropriate A.C. wall receptacle. Then insert the
charge cable into the battery charger jack.
2. The charger LED will indicate the status of the charger as
follows:
• A steady light indicates the battery is undergoing a fast
charge.
• A slow blinking light indicates the charger is in trickle mode.
The battery is ready for use.
• A rapidly blinking light indicates a problem with the battery.
The battery may have an internal short, or its charge monitoring circuitry may be malfunctioning. The battery should
not be used any further.
• Battery Packs may be charged either when installed in the
printer or when removed.
Do not attempt to charge batteries with the LI 72
while printing. Attempting to print while charging can
result in improperly charged batteries.
QL 320 User’s Guide
Loading the Media
You can operate this printer in one of two different modes: TearOff or Peel-Off. Tear-Off mode allows you to tear off each label (or
a strip of labels) after it is printed. In Peel-Off mode, the backing
material is peeled away from the label as it is printed. After you
remove this label, the next one is printed.
Installing the Media
1. Refer to Figure 4. Open the printer:
• Rotate the latch release levers on each side of the printer
as shown at “1” below.
The latch assembly will
flip open automatically
as shown at “2”.
• Rotate the media
Cover back as
shown at “3”, exposing the media
compartment
and the adjustable media
supports.
Media
Compartment
Media Supports
FIGURE 4
10
QL 320 User’s Guide
2. Refer to Figure 5. Load the media
• Determine that the core diameter of the media roll matches
the setting of the Media Disks. If it does not, adjust the media disks per Figure 6 below.
• If the media support setting is correct, pull the media supports apart, insert the roll of media between them, and let
the media supports close. Insure that the media pulls off
the core in the direction
shown in Figure 5. The
supports will adjust
themselves to the
width of the media,
and the media
should be able to
spin freely on the
supports.
Media Roll
Note direction
media pulls off
the roll.
Media Disk
must match
diameter of
Media Core.
FIGURE 5
Remove Media
Disk, rotate 180∞
and replace for
1.40” core
Media Disk set for
3/4” core (factory
default).
FIGURE 6
QL 320 User’s Guide
continued on next page
11
3. Refer to Figure 7. Close the Media Cover
• If you plan to use the printer in the tear-off mode, close the
media cover as shown at “2”, then rotate the latch assembly
as shown until it locks into place, as shown at “4”.
• If you plan to use the printer in the peel-off mode, peel a
few labels off of the media roll and pull it out of the printer
as shown at “1”. Close the media cover as shown at “2”.
Rotate the “EZ-Peel” peeler bar until it locks into place on
the latch, as shown at “3”, then rotate the Latch as shown
until it locks into place, as shown at “4”.
• Turn on the printer or press the Feed button if the printer is
already on.
The printer will advance the media to the next label, if printing labels. If you are printing on journal media, the printer
will advance a short strip of media and will then be ready
for printing.
Pull Media out of
Printer
Media Cover
“EZ-Peel” Peeler
Bar
Flip down after
Latch is closed if
using media in
the peel-off
mode.
Latch Assembly
FIGURE 7
12
QL 320 User’s Guide
Operator Controls
The QL 320 will come with one of two possible control panels.
The standard control panel is detailed below and in Figure 8. The
optional control panel (Figure 9) features an LCD which allows
easy display and selection of many printer functions and is detailed on following pages.
Standard Keypad
The standard keypad has three control buttons and two multipurpose indicators.
• The Power button turns the QL 320 on and off.
• The Feed button advances a length of media which is determined by the type of media being used. Label media will
be advanced to the next gap or bar sense marker. Journal
(plain) media will be advanced a length determined by the
printer’s software.
• The Function button is controlled by a printer’s specific application to support such functions as:
Print a battery Level reporting
Print the Local Area Network (LAN) status
Print a Short Range Radio Frequency (SRRF) status
Print a Media supply report
The green LED on the left side of the control panel indicates
the status of several printer features:
• A slowly blinking sequence indicates the printer’s battery
needs charging.
• Printers with a wireless QuickLink module installed: a quickly blinking sequence indicates the printer has not established a link to either a Local Area Network or a compatible
wireless equipped terminal.
• Printers with a wireless QuickLink module installed: A
steadily lit indicator shows that the printer has established a
wireless link, either to the LAN or to a compatible terminal.
A steadily lit green indicator on a non-wireless printer is a
power-on indicator.
The yellow LED on the right side of the control panel has two
indication conditions.
• A rapidly blinking yellow LED and a chime indicate that no
application has been loaded into the printer.
• Printers with a wireless QuickLink module installed: a rapidly blinking LED indicates normal data transmission.
QL 320 User’s Guide
13
• A steadily lit yellow LED indicates an error condition. This
can be caused by one of the following:
1. The media cover is not completely closed and latched.
2. The printer is out of media.
Green LED
Steady Light indicates power
on and/or established RF link.
Fast Blink indicates no RF link
(on RF equipped units only)
Slow Blink means low battery
Power Button
Press to turn unit on. Press
again to turn unit off
Yellow LED
Steady Light indicates error
condition: out of media or
media cover not closed.
Fast Blink indicates RF activity (on RF equipped units only)
Fast blink with beeper indicates no application loaded
Feed Button
Press to advance the media
one blank label or a software
determined length of journal
media.
Function Button
Specific functions are under
printer application control.
FIGURE 8: STANDARD CONTROL PANEL
14
QL 320 User’s Guide
LCD Control Panel
The optional LCD control panel has buttons for the power on/off
and media feed functions just as in the standard control panel. In
addition, it has two keys which allow easy navigation and selection of menu options affecting many printer functions.
The “Scroll” button allows scrolling through the various options
and settings. The “Select” button allows selection of the option or
function displayed on the screen.
Feed Button
Press to advance
the media one
blank label or a
software determined length of
journal media.
Power Button
Press to turn unit on.
Press again to turn
unit off
Scroll Button
Press to scroll through the
menu choices on the LCD.
Printer Status Icons
Indicates the status
of several printer
functions
Select Button
Press to select a menu
choice on the LCD.
LCD
See LCD Functions Table for
an overview of menu options
FIGURE 9: OPTIONAL LCD CONTROL PANEL
QL 320 User’s Guide
15
The top of the screen has a row of status icons which indicate
the state of various printer functions:
Indicates that the printer is associated with a wireless Local Area Network (LAN). This icon is functional only with
QL 320N network printers.
A flashing icon indicates low battery status. You
should suspend any printing operations and recharge or replace the battery Pack as soon as is convenient.
A flashing icon indicates that the media cover is open or
not properly latched.
A flashing icon indicates that a file is being downloaded
to the printer.
A flashing icon indicates that the printer does not detect
any media. This could indicate an out of media condition,
or improperly loaded media.
In addition to the status icons, the LCD control panel can display
many of the printer’s settings and functions as text. Applications
can be written to allow the user to view and /or modify these settings using the scroll and select keys on the display. Refer to the
“LCD Functions Table” on the following page for the full set of
printer features that can be made available with the LCD panel.
The LCD has a backlighting option which allows viewing of the
screen in a dark environment, or provides better contrast in a very
bright environment. Use of the display backlight will decrease the
time the printer will run between charges.
16
QL 320 User’s Guide
LCD Functions
Function
Default setting
Scroll & Select Options
Sensor Type
Gap
Print Width
Factory Set
Value
Baud Rate
19200
Data Bits
WLAN ID*
Factory Set
Value
Label Top
000
• Increase (+120 dots max.)
• Decrease (-120 dots max.)
Left Position
000
• Increase (+120 dots max.)
• Decrease (-120 dots max.)
LCD Contrast
No-activity Timeout
60 sec.
Print Darkness
(Head Temperature)
00
• Increase (+10 max.)
• Decrease (-10 max.)
Tear-off Position
00
• Increase (+120 dots max.)
• Decrease (-120 dots max.)
Media Type
Label
LCD Backlight
Off
• On
• Off
• Momentary On w/
time delay
Factory Reset
(Resets all to
factory set values)
No
• No
• Yes
• Bar
• Gap
• Increase (+120 dots max.)
• Decrease (-120 dots max.)
• 9600
• 19200
• 32400
• 7
• 8
N/A
• Increase
• Decrease
•
•
•
•
•
60 sec.
5 min.
10 min.
30 min
Custom*
• Label
• Journal
* Some parameters, such as the WLAN ID number and non-standard no-activity time out values can be set using a PC running Zebra’s Label Vista label
creation program and a data cable link to the printer.
QL 320 User’s Guide
17
Verify the Printer Is Working
Before you connect the printer to your computer or portable data
terminal, make sure that the printer is in proper working order.
You can do this by printing a configuration label using the “two key
reset” method. If you can’t get this label to print, refer to “Troubleshooting”.
Printing a Configuration Label
1. Turn the printer off. Load the media compartment with journal media (media with no black bars printed on the back)
2. Press and hold the Feed Button.
3. Press and release the Power button and keep the Feed button pressed. When printing starts, release the Feed button.
The unit will print a line of interlocking “x” characters to insure
all elements of the print head are working, print out the version of
software loaded in the printer and then print two reports.
The first report indicates model, ROM version, serial number,
baud rate, etc. The second report prints out more detailed information on the printer’s configuration and parameter settings. If no
second report appears, there is no application loaded. (See the
Troubleshooting Section for a sample print-out and a further discission on how to use the configuration label as a diagnostic tool.)
Connecting the Printer
The printer must establish communications with a host terminal
which sends the data to be printed. Communications occur in four
basic ways:
• By a cable between the printer and its host terminal
• Linking to a host terminal via Infrared (usually by means of
the industry standard IrDA protocol)
• By means of a Short Range Radio Frequency (SRRF) link.
• By means of a wireless LAN (Local Area Network). This
applies to QL 320N Network Printers only.
18
QL 320 User’s Guide
Cable Communications
CAUTION. The power should be turned off
connecting
or disconnecting the
before
communications cable.
All QL 320 printers can communicate by cable; the specific cable supplied with your printer will vary with the host terminal. The
8- pin circular connector on your communications cable plugs into
the serial communications port on the side of the QL 320 printer.
It is keyed to assure correct alignment; do not try to force it if it
does not plug in. The other end of the cable must be plugged into
the host terminal as shown in Figure 10, or to a serial port on a
computer (Figure 11.) Communications between the terminal and
the printer are controlled by the applications running on the terminal and the printer.
QL 320
Communications Port
Communications Cable to Terminal
Part number varies. Refer to Appendix A.
FIGURE 10
Serial Communications Cable to Computer
Refer to Appendix A for part numbers.
FIGURE 11
QL 320 User’s Guide
19
IR Communications
Printers equipped for infrared (IR) communications are identified
by a small “IR” logo on the unit’s label. IR allows wireless communications between the printer and the host terminal. IR units can
also communicate with a cable as detailed above, however, IR
functions are disabled when the cable is plugged in. QL 320 units
with the IR option can be configured to conform to the standard
IrDA communications protocol
Linking a Printer to an IrDA Host
IrDA compliant terminals will automatically initiate communications to the printer. First insure that there is a direct line of sight
between the printer and the terminal that will be sending data. The
IR window on the front of the QL 320 must face the corresponding
window on the terminal to properly send and receive signals. An
IrDA compliant terminal will seek out any linkable devices and establish communications between them, even turning the printer on
if necessary.
1M (39”)
Area of IR Window
FIGURE 12
20
QL 320 User’s Guide
SRRF Communications
Both the printer and the device it communicates with must follow
either the Bluetooth standard or Zebra’s proprietary SRRF protocol. The communications protocol is determined by the specific
QuickLink module installed in the printer.
Printers equipped for short range radio frequency communications (SRRF) allow wireless communication with their host terminals from any direction. Reliable transmission distances will vary
but usually exceed 1m. (39”) under worst conditions. SRRF printers can be identified by reading the printer’s model number label
on the front of the unit, which will show the radio module’s identification number and/or its operating frequency. QL 320 printers
equipped with a Bluetooth wireless module will have the Bluetooth
logo on the model number label.
Zebra SRRF Network Overview
Zebra’s short range RF network operates as a collection of
linked pairs of terminals and printers. There is no base station or
centralized control; control of the network is distributed across the
entire network.
Before SRRF operation can begin, the QL 320 must be “linked”
to a terminal with a compatible short-range radio. Linking means
that addresses are exchanged between the terminal and the printer. Once linked, the terminal and the printer become a “linked pair”
and communicate exclusively with each other. The terminal and
the printer can be turned on and off without affecting the link; it remains valid until another link is deliberately created. Thus it is not
necessary to perform a link every time that the equipment is used.
So long as the linked pair is kept together, they remain linked indefinitely. If the linked pair is not stored together, then the terminal
and printer selected should be linked prior to use.
Multiple linked pairs can be operated in close quarters and each
terminal will only communicate with its linked printer. Each SRRF
radio module has a unique device address (terminal or printer),
based on the device serial number.
Linking From the Terminal to the Printer
The linking operation can be activated from either the terminal
or the printer. If the terminal has a scanner available, then the barcoded serial number on the back of every printer can be scanned
and used to establish the printer’s unique address. Once the printer’s address is established, the terminal can then initiate a link to
that printer. If no scanner is available the user can manually enter
QL 320 User’s Guide
21
the serial number of the printer; however, this method is not recommended. The terminal can only capture the desired printer using this type of link.
The terminal must be programmed to guide the user through
scanning the printer serial number bar-code, then execute an algorithm which converts the serial number into an address. Zebra
can provide C source code to licensed OEM customers that handles the conversion from serial number to address.
Linking From the Printer to the Terminal
When no scanner is available, and/or no additional software is
to be written for the terminal, then the linking operation can be initiated solely by the printer.
In this procedure the printer broadcasts a message seeking an
available terminal. If a terminal “hears” the broadcast and is available, it will respond by linking to the printer.
To insure a secure link, the user must perform the link operation
far enough away from other operating terminals so that the printer
does not inadvertently capture some other user’s terminal. Any
other terminal that hears the broadcast message from the printer
may try to link to it, therefore you should insure that only one terminal is within broadcast range Feedback is available from the
printer as to the outcome of the link operation.
22
QL 320 User’s Guide
Bluetooth™ Networking Overview
Exposure to Radio Frequency Radiation
The radiated output power of this internal wireless
radio is far below the FCC radio frequency exposure
limits. Nevertheless, this Bluetooth radio must be used
in such a manner that the antenna is 2.5 cm or further
from the human body.
The radio and antenna are mounted internally in this
printer in such a way that, when the printer is used in a
standard configuration (belt clip, soft case, shoulder
strap), the 2.5 cm distance from the users body will be
met. Do not use the printer in an unauthorized manner.
The internal wireless radio operates within guidelines
found in radio frequency safety standards and
recommendations. The level of energy emitted is far
less than the electromagnetic energy emitted by
wireless devices such as mobile phones.
“Bluetooth” is a worldwide standard for the exchange of data between two devices via radio frequencies. Bluetooth radios are relatively low powered to help prevent interference with other
devices running at similar radio frequencies. This limits the range
of a Bluetooth device to about 10 meters (about 32 feet).
In order to exchange data, two Bluetooth enabled devices must
establish a connection. Bluetooth software is always running in
the background, ready to respond to connection requests. One
device (known as the master or the client) must request a connection with another. The second device (the slave or the server)
then accepts or rejects the connection. A Bluetooth enabled QL
320 will normally act as a slave, but in theory any Bluetooth device can be either a master or a slave. This miniature network is
sometimes referred to as a “piconet” and can consist of several
Bluetooth enabled devices.
Each Bluetooth QL 320 has a unique Bluetooth Device Address
(BDA) loaded into its Quick Link module when manufactured.
A Typical Bluetooth Connection Sequence
In this simplified sequence “Joe’s Terminal” is a Bluetooth ready
hand held terminal running an application that needs access to a
printer.
1. Joe’s Terminal performs a search of its “piconet” (a Device InQL 320 User’s Guide
23
quiry) and determines that there are four Bluetooth devices in the
vicinity.
2. Joe’s Terminal queries each of the four nearby devices to determine which services they provide (a Service Discovery). The
Bluetooth enabled QL 320 “Sandy’s Printer” offers the printing service.
3. Joe’s Terminal sends a print connection request to Sandy’s
Printer.
4. Sandy’s Printer evaluates the request and determines that
Joe’s Terminal is permitted to use the print service, but only if the
correct password is submitted.
5. Sandy’s Printer queries Joe’s Terminal for the password (Authentication).
6. Joe’s Terminal returns the correct password and the print connection is established.
7. After Joe’s Terminal is finished printing it disconnects with
Sandy’s Printer. (Some Bluetooth services disconnect automatically, others must be closed manually.)
There are several layers of security in the Bluetooth system, so
this sequence may not be a completely accurate representation of
how your printer may function in a Bluetooth environment. For the
most part, communications using the Bluetooth protocol are initiated and processed without any operator intervention, much like
the IrDA system described previously.
24
QL 320 User’s Guide
Wireless Local Area Network (WLAN)
WARNING: Use of the QL 320 will result in
exposure to Radio Frequency radiation. To conform to
FCC RF exposure requirements the printer must be
used only in the intended orientation and in the
intended manner.
Printers equipped for Wireless Local Area Network (WLAN)
communications using the industry standard 802.11 or 802.11b
protocols are known as QL 320N Printers. These printers allow
wireless communication as a node within a local area network,
and its wireless capabilities allow communications from any point
within the LAN’s perimeter. Methods of establishing communications to the QL 320 will vary with each LAN application.
QL 320N printers can be identified the model number on the
front of the unit.
The QL 320N is designed for use with either a shoulder strap
and a specially designed soft case, or with a belt clip. The printer
should be oriented on the operator’s hip so that printed material is
transported away from the operator.
When the QL 320N is used as designed, either the printer’s soft
case or the belt clip will allow use of the printer in the manner
mandated by the FCC.
QL 320 User’s Guide
25
Setting Up the Software
The QL 320 uses Zebra’s CPL Programming language which
was designed for mobile printing applications. CPL is fully described in the Mobile Printing Systems Programming Manual,
which is available in Portable Document Format (.pdf) on-line
at Zebra’s website
You can also use Label Vista™, Zebra’s Windows™ based label
creation program which uses a graphical interface to create and
edit labels in the CPL language. Label Vista is available either online at Zebra’s website, or on a CD (part number AC15065-1).
The QL 320 with its optional memory upgrade can support an
interpreter for ZPL II®, the programming language used by Zebra
desktop printers. To use ZPL II, refer to the ZPL II Programming
Guide. If you choose to use a third party label preparation system,
follow the installation instructions included in the package.
26
QL 320 User’s Guide
Adjustable Shoulder Strap
Refer to Figure 14, below.
Snap each end of the shoulder strap into the “D” rings in the top
of the printer. Slide the buckle away from or towards the printer
until you achieve the desired length.
Pull Strap here
to shorten
Hold Buckle
Pull Strap here
to lengthen
Snap in to “D”
rings on
printer
FIGURE 14
QL 320 User’s Guide
27
Belt Clip
If the QL 320 is equipped with a belt clip, hook the clip over your
belt, and ensure that the clip is securely attached to the belt. The
belt clip will pivot to allow you to move freely while wearing the
printer.
Dress cables
through this
slot
Clip printer to
belt
Printer can
pivot freely
FIGURE 15
28
QL 320 User’s Guide
Preventive Maintenance
WARNING: To avoid possible personal injury or
damage to the printer, never insert any pointed or sharp
objects into the printer.
Extending Battery Life
• Never expose the battery to direct sunlight or temperatures
over 104∞ F (40∞ C).
• Always use a Zebra charger designed specifically for Lithium-Ion batteries. Use of any other kind of charger may
damage the battery.
• Choose the media that is easiest to “burn.” An authorized
Zebra re-seller can help you determine the optimum media
for your application.
• If you print the same text or graphic on every label, consider using a pre-printed label.
• Choose the correct print darkness, and print speed for your
media.
• Use software handshaking (XON/XOFF) whenever possible.
• Select Tear-Off mode whenever possible (Peel-Off mode
uses more power).
• If your printer has the optional LCD display: Use the display
backlight only when necessary. Turn it off whenever it is not
needed. The LCD backlight consumes a great deal of power.
• Pull the battery out of the printer if the printer won’t be used
for a day or more and you’re not performing a maintenance
charge.
• Consider purchasing an extra battery.
• Remember that any rechargeable battery will lose its ability
to maintain a charge over time. It can only be recharged a
finite number of times before it must be replaced.
QL 320 User’s Guide
29
Label
Presence
Sensor
Peeler Bar Rollers
Tear Bar
Printhead
Elements
Bar Sensor
Gap Sensor
Platen
Peeler Bar
FIGURE 16
30
QL 320 User’s Guide
Cleaning
CAUTION.- Use only the cleaning agents
indicated. Zebra Technologies Corporation will not be
responsible for damage caused by any other cleaning
materials used on this printer.
Never use any sharp objects on the printer mechanism
as it could damage the print head. Use only the
cleaning pen supplied with the printer or a cotton swab
saturated with alcohol for cleaning the printer.
Area
Printhead
(Figure 16)
Platen Roller
(Figure 16)
Peel bar
(Figure 16)
Method
Use the supplied cleaning pen or 70%
isopropyl alcohol on a cotton swab to
clean the print elements from end to
end (the print elements are located in
the thin gray line on the printhead).
If print quality has not improved after
performing this procedure, try cleaning
the printhead with a Cleaning Pad.
This specially prepared material
removes contamination buildup without
damaging the printhead. Refer to
Appendix C for more information.
Interval
After every five
rolls of media (or
more often, if
needed)
Linerless media
requires more
frequent
cleaning.
Rotate the platen roller and clean it
thoroughly with the cleaning pen or
70% isopropyl alcohol and a cotton
swab.
Units with linerless platens: No
cleaning is necessary. Do not use
alcohol on linerless platens!
Clean thoroughly with the cleaning pen
or 70% isopropyl alcohol and a cotton
swab.
Tear bar
(Figure 16)
Clean thoroughly with the cleaning pen
or 70% isopropyl alcohol and a cotton
swab.
Exterior
Water-dampened cloth
Interior
(Figure 16)
Brush/air blow. Insure the Bar
Sensor, Gap Sensor and Label
Present Sensor windows are free of
dust.
QL 320 User’s Guide
As needed
31
Troubleshooting
Standard Control Panel
If the printer is not functioning properly, refer to the chart below
to find the state of the two LEDs on the Control Panel. Then refer
to the Troubleshooting topic referenced in the chart to resolve the
problem.
Green LED
Yellow LED
Indication
Ref. to Topic
Steady
Off
Normal Operation,
and/or RF Link established
n/a
Off
Off
Power Off
Fast Blink
Off
No RF Link
6, 11
Slow Blink
Off
Low Battery
3, 6, 7
Steady
Steady
Out of media, or
Media Cover not closed
9, 11
Steady
Fast Blink
Normal RF activity
Steady
Fast Blink,
Beeper Sounds
No application
Optional LCD Control Panel
The top of the display shows several icons which indicate various printer functions. Check the indicator status, then refer to the
Troubleshooting topic referenced in the chart to resolve the problem.
Status Icon
Blank Screen
32
Condition
Indication
Ref. to Topic
Steady
Off
RF Link established
No RF Link
n/a
Flashing
Low Battery
3, 6, 7
Flashing
Head latch not closed
9, 11
Flashing
Printer is receiving a file
Flashing
Out of media,
9, 11
n/a
No application
1,13
QL 320 User’s Guide
Troubleshooting Topics
1. No power
• Check that battery is installed properly
• Recharge or replace battery as necessary.
2. Media does not feed:
• Be sure print head is closed and latched.
• Check spindle holding media for any binding.
• If unit is equipped with label presence sensor:
Insure most recently printed label is removed.
Also insure label sensor is not blocked.
3. Poor or faded print or
flashing:
• Clean print head.
• Check battery and recharge or replace as necessary
• Check quality of media.
4. Partial/missing print:
• Check media alignment
• Clean print head.
• Insure printhead is properly closed and latched.
5. Garbled print:
• Check baud rate.
6. No print:
•
•
•
•
Check baud rate
Replace battery
Check cable to terminal
Establish RF Link (Wireless units only) or restore LAN
associativity (QL 320N models only)
• Invalid label format or command structure — put printer in
Communications Diagnostic (Hex Dump) Mode to diagnose
problem.
7. Reduced battery life
• Check battery date code — if battery is one to two years old,
short life may be due to normal aging.
• Recondition battery.
• Replace battery.
8. Yellow error light or
flashing:
• No application or application corrupted: reload program.
• If using wireless communications: flashing indicator is normal
while data is being transmitted or received.
continued on next page
QL 320 User’s Guide
33
9. Yellow error light always on,
or
flashing:
• Check media is loaded and print head is closed and
securely latched.
10. Skips labels:
• Check media for top of form sense mark or label gap.
• Check that the maximum print field has not been exceeded on
label.
• Insure bar/ or gap sensor is not blocked or
malfunctioning
11. Communication Error:
• Check media is loaded, head is closed and error
light is off.
• Check baud rate.
• Replace cable to terminal.
12. Label Jam:
• Open head release latch and media cover.
• Generously apply alcohol to printer in area of
jammed label.
13. Blank LCD Screen (only for units with optional LCD
control panel)
• No application loaded or application corrupted: reload program.
Troubleshooting Tests
Printing a Configuration Label
To print out a listing of the printer’s current configuration follow
these steps:
1. Turn the printer off. Load the media compartment with journal media (media with no black bars printed on the back)
2. Press and hold the Feed Button.
3. Press and release the Power button and keep the Feed button pressed. When printing starts, release the Feed button.
The printer will generate a configuration label as shown on Figures 17 and 17a :
34
QL 320 User’s Guide
Sample Configuration Label
Print Head Test
End of First Report
Unit Serial Number
Application Number
Report appears only on
units with wireless options
installed.
Units with no wireless
options will print an empty
line and resume the report.
Peripherals installed: In
this example the LCD
display option is not
installed.
FIGURE 17
continued on next page
QL 320 User’s Guide
35
Sample Configuration Label (continued)
Flash Memory Size
Maximum Label Size
Resident Fonts
Pre-scaled font (.cpf)
listed separately
Files Loaded in Printer
Memory (will include Prescaled or Scalable Fonts)
Amount of Memory
Available
Instructions on entering
Communications
Diagnostics (Dump) Mode.
FIGURE 17A
36
QL 320 User’s Guide
Communications Diagnostics
If there’s a problem transferring data between the computer and
the printer, try putting the printer in the Communications Diagnostics Mode (also referred to as the “DUMP” mode). The printer will
print the ASCII characters and their and their text representation
(or the period ‘.’, if not a printable character) for any data received
from the host computer
To enter Communications Diagnostics Mode:
1. Print a configuration label as described on pg. 34.
5. At the end of 2nd diagnostics report, the printer will print:
“Press FEED key to enter DUMP mode”.
6. Press the FEED key. The printer will print: “Entering DUMP
mode”.
Note: If the FEED key is not pressed within 3 seconds, the printer will print “DUMP
mode not entered” and will resume normal operation.
7. At this point, the printer is in DUMP mode and will print the
ASCII hex codes of any data sent to it, and their text representation (or “.” if not a printable character).
Additionally, a file with a “.dmp” extension containing the ASCII
information will be created and stored in the printer’s memory. It
can be viewed, “cloned” or deleted using the Label Vista application. (Refer the Label Vista documentation for more information.)
To terminate the Communications Diagnostics Mode and return
the printer to normal operations:
1. Turn the printer OFF.
2. Wait 5 seconds.
3. Turn the printer ON.
Calling the Help Desk
If the printer fails to print the configuration label, or you encounter problems not covered in the Troubleshooting Guide, contact
the Help Desk. Help Desk addresses and phone numbers for
your area can be found in Appendix D of this manual. The Help
Desk will need the following information:
• Model number/type (e.g. QL 320)
• Unit serial number (Found on the large label on the back of
the printer, also found in the configuration label printout))
• Product Configuration Code (PCC) (15 digit number found
on the small label on the back of the unit)
QL 320 User’s Guide
37
Specifications
NOTE.- Printer specifications are subject to change without notice.
Printing Specifications
Print Density
203 dots/inch (8 dots/mm)
Print Width
Up to 2.9“ (71.2 mm)
Print Speed
4” per second (101.6 mm per second)
Print Head Life,
calculated
1,964,160” (50 Km) nominal
Distance from
Print Element
to Top of Form
.571” (14.5 mm)
116 dots
Memory/Communications Specifications
Flash Memory
1 MB flash (standard); 2MB flash (optional)
SRAM Memory
1MB SRAM (standard); 2 MB SRAM (optional)
Standard
Communications
RS-232 serial port (8 Pin circular DIN connector)
Configurable Baud rate (from 9600 to 57.6 Kbps),
parity and data bits.
Software (X-ON/X-OFF) or hardware (DTR/STR)
communication handshake protocols.
Infrared wireless link (meets IrDA 1.1 communications
specifications) 2,400 to 115,200 Baud rate
Optional Wireless
Communications
Bluetooth compatible 2.4 GHz SRRF link
Optional SRRF frequencies of 916 MHz and 2.4 GHz per
Zebra proprietary wireless protocol.
Optional wireless LAN capabilities comply with 802.11 and
802.11b protocols
38
QL 320 User’s Guide
Label Specifications
Label/Tag Width
1.5" to 3.1" (38.1 mm to 78.4 mm)
Max. Label/
Tag Length
16" (406.4 mm) with standard memory
Inter-label Gap.
.08" to .16" (.12" preferred)
2 mm to 4 mm (3 mm preferred)
Label/Tag Thickness
.0025” to .0065” (.064 mm to .165 mm)
Label Roll Size:
Max. Diameter
2.625" (66.7 mm) O.D.
Inner Core
Diameter
Media Requirements
.75" (19 mm) std, 1.38” (35.05 mm) optional
Use Zebra-brand direct thermal media that is outside
wound. Media may be reflective (black mark) sensing or
transmissive (gap) sensing, die-cut, continuous or
linerless.
For die-cut labels, use only full auto dies.
The reflective media black marks should extend past
the centerline of the roll.
Minimum Black Mark Dimensions:
Mark width: 0.5” (12.7mm) perpendicular to the edge of
the media, centered within the width of the roll.
Mark length: 0.094” (2.4 mm) parallel to the edge of the
media.
Font/Bar Code Specifications
Fonts Available
1D Bar Codes Available
Five resident scalable and rotatable fonts available
from 12-48 pt.
Downloadable pre-scaled fonts via Label Vista™
software
Optional international character sets
Codabar
UCC/EAN 128
Code 39
Code 93
EAN 8/JAN 8, 2 and 5 digit extensions
EAN 13/JAN 13, 2 and 5 digit extensions
lnterleaved 2 of 5
MSI/Plessey
FIM/POSTNET
UPC-A, 2 and 5 digit extensions
UPC E, 2 and 5 digit extensions
2D Bar Codes Available
MaxiCode
PDF 417
Rotation Angles
0∞, 90∞, 180∞, and 270∞
QL 320 User’s Guide
39
Physical/Environmental/Electrical Specifications
3.9”
[97.9 mm]
3.1”
[78.7 mm]
8.0”
[203.2 mm]
8.3”
[210.2 mm]
4.60”
[116.8 mm]
FIGURE 18 OVERALL DIMENSIONS
Weight
w/ battery
excluding media.
Temperature
Operating
Storage
5∞ to 122∞ F (-15∞ to 50∞ C)
-13∞ to 158∞ F (-25∞ to 70∞ C) Range
Relative Humidity
Operation
Storage
10% to 80% (non-condensing)
10% to 90% (non-condensing)
Electrical
40
1.65 lbs. (.75 kg. )
Battery: 7.4V Lithium-Ion
Charger: External battery charger, 120-230 VAC
depending on model selected.
QL 320 User’s Guide
Communications Port
Signal
Pin#
Name
RXD
TXD
CTS
RTS
Type
Description
input
output
input
output
Receive Data
Transmit Data
Clear To Send from host
Request To Send
set high when printer
is ready to accept command
/data
GND
NC
DSR
input
Ground
No Connect
Data Set Ready
low to high transition turns
printer on, high to low
transition turns printer off
(if enabled)
DTR
output
Data Terminal Ready
set high when printer is on
(set to battery voltage for
“S” versions)
FIGURE 19 COMMUNICATIONS PORT
(8 pin Circular DIN)
QL 320 User’s Guide
41
Agency Approvals
• FCC Part 15 Subpart B Class A Electromagnetic Radiation
Standard
• Built to UL, CUL and TUV standards
• EN50082-1 International lmmunity Standard
• EN55022 Class B European Electromagnetic Radiation
Standard
Accessories
• Adjustable shoulder strap
• Protective soft case
• Extra battery packs
• 120-230 VAC battery charger
• Desk Mount
• Data cables
For details, call your authorized Zebra re-seller.
Appendix A
Interface Cables
Part Number ´BL11757-000; 8-Pin DIN to 9-Pin DB PC Cable
This part is also available as a coiled cable under Part Number
BL15063-1.
For Use With a Personal Computer
Pin 9
PC Signals
(TXD)
(RXD)
(RTS)
Pin 1 (CTS)
(GND)
DB-9 Pin
(DTR)
Female Plug
(DSR)
(to P.C.)
Shield
Printer Signals
1 (RXD)
2 (TXD)
3 (CTS)
4 (RTS)
5 (GND)
7 (DSR)
8 (DTR)
Shield
QL Series User’s Guide Appendices
8 Pin
Male Plug
(to printer)
43
44
QL Series User’s Guide Appendices
PDT3100/3500
/6100 Series
PDT3100 Series
SYMBOL
PDT3300 Series
PDT4100 Series
NORAND
RT1100/1700 Series
RT1100/1700 Series
RT5900 Series
RT1100/1700 Series
RT1100/1700 Series
RT1100/1700 Series
6400
COMPSEE
Apex II
LXE
MX1,MX3
1380,1390,1590
2325
Terminal
8’ /Coiled
8’ /Coiled
BL12093-2
6’ /Straight
BL12093-1
8’ /Coiled
RJ45
RJ45
9 Pin DB Fem.
DB25 male
6’/Straight
BL11757-000
9 Pin DB
8’ /Coiled
8’ /Coiled
8’ /Coiled
8’ /Coiled
BL12803-1
BL12804-1
BL13298-1
BL13309-1
BL11757-000
BL11391-000
15 Pin D-Sub
6 Pin MiniDIN
6 Pin MiniDIN
6 Pin Mini DIN
8’ /Coiled
12’/Coiled
6 Pin MinDIN
6 Pin MiniDIN
RJ45
9 Pin DB
9 Pin DB
RJ45
Terminal
Connector
BL11537-1
BL11537-2
6’/Straight
8’/Coiled
6’/Straight
BL17757-000
BL17757-000
BL12093-1
8’ Coiled
Cord
Lgth/Type
BL12093-3
Cable
Part Number
Power On/Off (+5V)
Notes
8 Pin DIN
8 Pin DIN
8 Pin DIN
8 Pin DIN
Percon Falcon
Power On/Off (DTR Line)
Must be used with Symbol RS232
Adapter - Symbol PN#25-12059-01
a. Power On/Off (+5V) b. Used for the
8 Pin DIN
8 Pin DIN -Locking
8 Pin DIN Over-molded Auto ON/OFF
8Pin DIN
Auto ON/OFF
8 Pin DIN
8 Pin DIN Over-molded
8 Pin DIN Over-molded
8 Pin DIN
8 Pin DIN
8 Pin DIN
8 Pin DIN
Printer
Connector
Appendix A
INTERFACE CABLES
TELXON
960
960SL Adapter
for BL11122-1
960 (BL11122-1)
& 960SL (CC13711-1)
960
860 & 912
TEKLOGIC
7030 ILR
7025 ILR
SYMBOL (CONT.)
SPT1700 Series
SPT2700 Series
LRT/LDT3800 Series
LRT/LDT3800 Series
(2 Way)
LRT/LDT3800
& 6800 Series
LRT/LDT3800
& 6800 Series
Terminal
PIM Optical
6’ / Coiled
6’ / Coiled
CC11371-14
CC11371-15
8’ /Coiled
n/a
n/a
8’ /Coiled
8’ /Coiled
CP74005
BL12996-1
CL11314-000
Coiled
Coiled
BL11122-1
CC13711-1
BL13285-2
BL13285-1
PIM Optical
QL Series User’s Guide Appendices
RJ45
DB25
n/a
RJ45
n/a
36 Pin IDC Fem
15 Pin DB male
PIM Optical
PIM Optical
Cradle
Cradle
9’ /Coiled
9’ /Coiled
6’ / Coiled
Terminal
Connector
6’ /Coiled
Cord
Lgth/Type
BL15483-1
BL15482-1
CC11371-3
CC11371-14
Cable
Part Number
8 Pin DIN-Locking
8 Pin DIN
n/a
8 Pin DIN
n/a
8 Pin DIN
8 Pin DIN
8 Pin DIN
8 Pin DIN
8 Pin DIN
8 Pin DIN
8 Pin DIN
8 Pin DIN
Printer
Connector
“S” Printers Only
“S” Printers Only
No Power On/Off (DTR Line)
Power On/Off (DTR Line)
“S” Printers Only
“S” Printers Only
Notes
Appendix A
INTERFACE CABLES (continued)
45
Appendix B
Media Supplies
To insure maximum printer life and consistent print quality and
performance for your individual application, it is recommended
that only media produced by Zebra be used. These advantages
include:
• Consistent quality and reliability of media products.
• Large range of stocked and standard formats.
• In-house custom format design service.
• Large production capacity which services the needs of
many large and small media consumers including major retail chains world wide.
• Media products that meet or exceed industry standards.
For more information call Zebra Technologies Corporation at
+1.401.739.5800 and ask to speak to a Media Sales Representative.
46
QL Series User’s Guide Appendices
Appendix C
Maintenance Supplies
In addition to using quality media provided by Zebra, it is recommended that the printer be cleaned as prescribed in the maintenance section. The following items are available for this purpose:
• Cleaning Pen (10 pack), Reorder No. AN11209-1
• Cleaning Kit with Cleaning Pen, and Cotton Swabs, Reorder No. AT702-1
QL Series User’s Guide Appendices
47
Appendix D
Product Support
When calling with a specific problem regarding your printer,
please have the following information on hand:
• Model number/type (e.g. QL 320)
• Unit serial number (Found on the large label on the back of
the printer)
• Product Configuration Code (PCC) (15 digit number found
on the small label on the back of the unit)
Contact the Help Desk at:
Zebra Technologies Corporation
30 Plan Way
Warwick, Rhode Island 02886-1012 USA
Telephone:
+1 401.739.5800
Fax:
+1 401.732.7808
e-mail:
risupport@zebra.com
In Europe:
Zebra Technologies Europe, Limited
Zebra House
The Valley Centre, Gordon Road
High Wycombe
Buckinghamshire HP13 6EQ, United Kingdom
Telephone:
+44 1494 768298
Fax:
+44 1494 768210
e-mail:
tseurope@zebra.com
Ask for Customer Support
48
QL Series User’s Guide Appendices
Index
peel-off mode 12
tear-off mode 12
Accessories 42
Agency Approvals 42
Operator Controls 13
LCD Keypad 15
functions displayed 17
Standard Keypad 13
error indicator 14
power-on indicator 13
Battery, charging 9
while printing 9
Battery, installing 9
Battery life, tips 29
Belt clip 25, 28
Bluetooth Device Address
(BDA). See Communications:
short range radio frequency
(SRRF): Bluetooth™
piconet. See Communications: SRRF: Bluetooth™
Platen
linerless 31
Programming language
CPL 7
ZPL II 26
interpreter for 7
Charger, battery 9
Cleaning
Exterior 31
Interior 31
Linerless platen roller 31
Peel bar 31
Platen roller 31
Printhead 31
Sensors 31
Tear bar 31
QuickLink™ module 13
Shoulder Strap, adjusting 27
Software 26
Specifications
Font/bar Code 39
Label 39
Memory/communications 38
Physical 40
printing 38
Communications
Connector signals 41
infrared (IR) 20
SRRF 21
Bluetooth™ 23
Zebra propietary protocol 21
with a cable 19
Communications diagnostics 37
Configuration label 34
sample printout 35, 36
Damage, shipping 7
Help Desk, contacting 37
Troubleshooting
entering Communications
Diagnostics Mode 37
entering Communications
Diagnostics Mode Diagnosti 37
LCD Control Panel 32
Standard control panel indicators
32
Troubleshooting tests 34
printing a configuration label 18
Troubleshooting Topics 33
Label Vista 17, 26
use in troubleshooting 37
LAN. See Wireless communication: Local Area Network
Wireless communication
Local Area Network 13, 25
Manual
CPL Programming 7, 26
ZPL II Programming 7, 26
Media, loading 10
adjusting for core diameter 11
QL 320 User’s Guide Index
49
Patent Information
This product and/or its use may be covered by one or more of the
following US patents and corresponding international patents
worldwide
D275,286
D347,021
D389,178
D430,199
D433,702
3,964,673
4,019,676
4,044,946
4,360,798
4,369,361
4,387,297
4,460,120
4,496,831
4,593,186
4,607,156
4,673,805
4,736,095
4,758,717
4,816,660
4,845,350
4,896,026
4,897,532
4,923,281
4,933,538
4,992,717
5,015,833
5,017,765
5,304,786
5,479,441
5,909,233
5,021,641
5,029,183
5,047,617
5,103,461
5,113,445
5,140,144
5,132,709
5,142,550
5,149,950
5,157,687
5,304,788
5,321,246
5,335,170
5,364,133
5,367,151
5,372,439
5,373,148
5,378,882
5,396,053
5,396,055
5,486,057
5,503,483
5,504,322
5,528,621
5,532,469
5,543,610
5,545,889
5,552,592
5,570,123
5,578,810
5,976,720
5,978,004
5,995,128
5,997,193
6,004,053
6,010,257
6,020,906
6,034,708
6,036,383
6,057,870
5,168,148
5,168,149
5,399,846
5,408,081
5,589,680
5,612,531
6,068,415
6,070,805
5,180,904
5,229,591
5,410,139
5,410,140
5,642,666
5,657,066
6,095,704
6,109,801
5,230,088
5,235,167
5,243,655
5,247,162
5,250,791
5,250,792
5,262,627
5,267,800
5,412,198
5,415,482
5,418,812
5,420,411
5,436,440
5,444,231
5,449,891
5,449,893
5,768,991
5,790,162
5,791,796
5,806,993
5,813,343
5,816,718
5,820,279
5,848,848
6,123,471
6,147,767
6,151,037
6,201,255B1
6,231,253B1
6,261,009
6,261,013
6,267,521
5,280,163
5,280,164
5,280,498
5,468,949
5,479,000
5,479,002
5,860,753
5,872,585
5,874,980
6,270,072B1
6,285,845B1
6,292,595
6,296,032


---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Encryption                      : Standard V1.2 (40-bit)
User Access                     : Print, Fill forms, Extract, Assemble, Print high-res
Create Date                     : 2002:03:11 12:07:08-05:00
Modify Date                     : 2002:04:01 09:57:28-05:00
Subject                         : QL 320 User's Manual rev D
Page Count                      : 52
Creation Date                   : 2002:03:11 12:07:08-05:00
Mod Date                        : 2002:04:01 09:57:28-05:00
Producer                        : Acrobat Distiller 5.00 for Macintosh
Author                          : Zebra Technologies Corporation, MPCOE, Warwick
Keywords                        : 
Metadata Date                   : 2002:03:11 17:07:08Z
Creator                         : Zebra Technologies Corporation, MPCOE, Warwick
Title                           : UMAN-Q3D.pdf
Description                     : QL 320 User's Manual rev D
Page Mode                       : UseOutlines

EXIF Metadata provided by EXIF.tools