Zebra Technologies RFID-R4CXNG-01 P4T with Zcomax WiFi plus RFID radio User Manual 3 of 3
Zebra Technologies Corporation P4T with Zcomax WiFi plus RFID radio 3 of 3
Contents
user manual 3 of 3
P4T/RP4T
User Guide
30
Bluetooth ZBR4 Radio
The following section only applies when the Bluetooth ZBR4 module is installed in a P4T
series printer. This radio conguration has demonstrated compliance to FCC regulations.
P4T series printers with this conguration sold in North America will have the FCC ID:
I28-MD-ZBR4WA and the Industrie Canada ID: 3798B-ZBR4WA for this radio module on a
label on the back of the printer.
Caution • Exposure to Radio Frequency Radiation.
The radiated output power of this internal Bluetooth radio
is far below the FCC radio frequency exposure limits. The
internal Bluetooth radio operates within guidelines found
in radio frequency safety standards and recommendations.
Do not use the printer in an unauthorized manner.
Note • The following section only applies when the ZBR4
Bluetooth Radio is installed in a P4T Series printer. Unless
specified elsewhere in this manual, the antenna used for this
transmitter must not be co-located or must not operate in
conjunction with any other antenna.
European Regulatory Information for the ZBR4 Bluetooth Radio
This device is intended for use in all EU and EFTA member states.
Europe – EU Declaration of Conformity
This device complies with the essential requirements of the R&TTE Directive
1999/5/EC. The following test methods have been applied in order to prove
presumption of compliance with the R&TTE Directive 1999/5/EC:
• EN 60950-1 Safety of Information Technology Equipment
• EN 300 328-2 Technical requirements for spread-spectrum radio
equipment
• EN 301 489-1/-17 EMC requirements for spread-spectrum radio equipment.
This device is a 2.4 GHz wireless LAN transceiver, intended for indoor home and
office use in all EU and EFTA member states.
WLAN Module Using 802.11b/g Radio
The following section only applies when the 802.11b/g WLAN module is installed in a P4T
series printer. Other than conditions specied elsewhere in this manual, only one of the
radio options can be installed in the printer at one time and the antenna used for these
transmitters must not be co-located or must not operate in conjunction with any other
antenna.
P4T Series printers for sale in North America will have the 802.11b/g radio FCC ID: 128-PLAN11BG or
FCC ID: I28MD-CXLAN11G, and the Industrie Canada ID: 3798B-PLAN11BG or Industrie Canada ID:
3798B-CXLAN11G printed on a label on the back of the unit.
Caution • The radiated output power of this internal 802.11b/g WLAN radio is far below
the FCC radio frequency exposure limits. The internal radio operates within guidelines
found in radio frequency safety standards and recommendations. Do not use the
printer in an unauthorized manner.
Caution • Use of a P4T printer with the radio module marked with FCC ID:
128-PLAN11BG or FCC ID: I28MD-CXLAN11G meets the FCC requirements for
radio frequency (RF) radiation exposure in the standard body worn conguration
with no minimum separation. In this conguration, which applies whether the
belt clip or shoulder strap is used, the face of the printer from which paper is
transported is facing away from the user’s body. The standard conguration
must always be used when the printer is body worn.
Industry Canada (IC) Warning
This device complies with Industry Canada license-exempt RSS standard(s). Operation
is subject to the following two conditions:
1) This device may not cause interference.
2) This device must accept any interference, including interference that may cause un-
desired operation of the device.
European Regulatory Information for this Radio
AT BE CY CZ DK
EE FI FR DE GR
HU IE IT LV LT
LU MT NL PL PT
SK SI ES SE GB
Note: -Member states in the EU with restrictive use for this device are
crossed out!
This device is also authorized for use in all EFTA member states (CH, IS, LI, NO)
Important Notice:
This device is a portable RF printer intended
for commercial and industrial use in all EU
and EFTA member states.
Important Notice:
This device is a portable RF printer
intended for commercial and industrial use
in all EU and EFTA member states except in
France where restrictive use applies
Radio Regulatory Information
Section Continues
Printer Preparation
pg. 7
Connecting the
Printer pg. 26
Radio Regulatory
Information pg. 30
RP4T Printers
pg. 34 Maintenance pg. 35 Troubleshooting
pg. 37
Specications
pg. 42 Appendices pg. 45 Index pg. 51
P4T Overview-
pg. 5
Manual
Introduction pg. 4
P4T/RP4T
User Guide
31
Europe – EU Declaration of Conformity
This device complies with the essential requirements of the R&TTE Directive
1999/5/EC. The following test methods have been applied in order to prove
presumption of compliance with the R&TTE Directive 1999/5/EC:
• EN55022
European Emissions Standard
• EN 60950-1
Safety of Information Technology Equipment
• EN 300 328-2
Technical requirements for spread-spectrum radio equipment
• EN 301 489-17
EMC requirements for spread-spectrum radio equipment.
This device is a 2.4 GHz wireless LAN transceiver, intended for indoor home and
office use in all EU and EFTA member states, except in France where restrictive
use applies.
The use of this frequency band in France is subject to restrictions. You may only
use channels 10 and 11 (2457 and 2462 MHz) on French territory, except in those
French departments as listed in the table below where channels 1-13 (2412-
2472 MHz) may be used. For more information see http://www.anfr.fr/ and/or
http://www.art-telecom.fr
01 Ain 36 Indre 69 Rhone
02 Aisne 37 Indre et Loire 70 Haute Saone
03 Allier 39 Jura 71 Saone et Loire
05 Hautes Alpes 41 Loir et Cher 72 Sarthe
08 Ardennes 42 Loire 75 Paris
09 Ariege 45 Loiret 77 Seine et Marne
10 Aube 50 Manche 78 Yvelines
11 Aude 54 Meurthe et
Moselle 79 Deux Sievres
12 Aveyron 55 Meuse 82 Tarn et Garonne
16 Charente 57 Moselle 84 Vaucluse
19 Correze 58 Nievre 86 Vienne
2A Corse Sud 59 Nord 88 Vosges
2B Haute Corse 60 Oise 89 Yonne
21 Cote d’Or 61 Orne 90 Territoire de Belfort
24 Dordogne 63 Puy de Dome 91 Essonne
25 Doubs 64 Pyrenees
Atlantique 92 Hauts de Seine
26 Drome 65 Hautes Pyrenees 93 Seine St Denis
27 Eure 66 Pyrenees
Orientales 94 Val de Marne
32 Gers 67 Bas Rhin
35 Ille et Vilaine 68 Haute Rhin
Republic of China Regulatory Information for the 802.11b/g Radio
經型式認證合格之低功率射頻電機,非經許可,公司、商號或使用
者均不得擅自變更頻率、加大功率或變更原設計之特性及功能。
低功率射頻電機之使用不得影響飛航安全及干擾合法通信;經發
現有干擾現象時,應立即停用,並改善至無干擾時方得繼續使用。
前項合法通信,指依電信法規定作業之無線電通信。低功率射頻
電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備
之干擾。
According to “Administrative Regulations on Low Power Radio Waves Radiated Devices”
Without permission granted by the DGT, any company, enterprise, or user is not
allowed to change frequency, enhance transmitting power or alter original characteristic
as well as performance to a approved low power radio-frequency devices. The low
power radio-frequency devices shall not influence aircraft security and interfere
legal communications; If found, the user shall cease operating immediately until no
interference is achieved. The said legal communications means radio communications
is operated in compliance with the Telecommunications Act.
The low power radio-frequency devices must be susceptible with the interference from
legal communications or ISM radio wave radiated devices.
NCC (Taiwan) Compliance Statement
“經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變
更頻率、加大功率或變更原設計之特性及功能。 低功率射頻電機之使用不得影響飛航
安全及干擾合法通信 ；經發現有干擾現象時，應立即停用，並改善至無干擾時方得繼
續使用。 前項合法通信，指依電信法規定作業之無線電通信。低功率射頻電機須忍受
合法通信或工業、科學 醫療用電波輻射性電機設備之干擾。”
KC (Korea) Compliance Statement
For 2.4 GHz Radio device:
For Class B Equipment
이 기기는 가정용(B급)으로 전자파적합등록을 한 기기로서
주로 가정에서 사용하는 것을 목적으로 하며, 모든 지역에서 사용할 수 있습니다.
Section Continues
Printer Preparation
pg. 7
Connecting the
Printer pg. 26
Radio Regulatory
Information pg. 30
RP4T Printers
pg. 34 Maintenance pg. 35 Troubleshooting
pg. 37
Specications
pg. 42 Appendices pg. 45 Index pg. 51
P4T Overview-
pg. 5
Manual
Introduction pg. 4
P4T/RP4T
User Guide
32
802.11b/g and Bluetooth Co-located Radio
Modules
The following section only applies when the CF (Compact Flash) WLAN module and
Bluetooth ZBR4 module are installed in a P4T printer. This co-located radio conguration
has demonstrated compliance to FCC regulations. P4T printers with this conguration
sold in North America will have the FCC ID: I28-ZB4LAN-01 and the Industrie Canada ID:
3798B-ZB4LAN01 for this radio conguration printed on a label on the back of the printer.
Caution • Use of a P4T printer with the co-located ZBR4
Bluetooth radio module and the 802.11b/g WLAN radio
module meets the FCC requirements for radio frequency (RF)
radiation exposure in the standard body worn configuration
with no minimum separation. In this configuration, which
applies whether the belt clip or shoulder strap is used, the
face of the printer from which paper is transported is facing
away from the user’s body. The standard configuration must
always be used when the printer is body worn.
The radiated output power of this radio configuration is far
below the FCC radio frequency exposure limits. Both the
internal Bluetooth and the 802.11b/G radio operate within
guidelines found in radio frequency safety standards and
recommendations. Do not use the printer in an unauthorized
manner.
RP4T printers are not congured with this radio option.
European Regulatory Information for the Compact Flash 802.11b Radio
and Bluetooth Co-located Radio Modules
AT BE CY CZ DK
EE FI FR DE GR
HU IE IT LV LT
LU MT NL PL PT
SK SI ES SE GB
Note: -Member states in the EU with restrictive use for this device are
crossed out!
This device is also authorized for use in all EFTA member states (CH, IS, LI, NO)
Europe – EU Declaration of Conformity
This device complies with the essential requirements of the R&TTE Directive
1999/5/EC. The following test methods have been applied in order to prove
presumption of compliance with the R&TTE Directive 1999/5/EC:
• EN 60950-1
Safety of Information Technology Equipment
• EN 300 328-2
Technical requirements for spread-spectrum radio equipment
• EN 301 489-17
EMC requirements for spread-spectrum radio equipment.
This device is a 2.4 GHz wireless LAN transceiver, intended for indoor home and
office use in all EU and EFTA member states, except in France where restrictive
use applies.
The use of this frequency band in France is subject to restrictions. You may only
use channels 10 and 11 (2457 and 2462 MHz) on French territory, except in those
French departments as listed in the table below where channels 1-13 (2412-
2472 MHz) may be used. For more information see http://www.anfr.fr/ and/or
http://www.art-telecom.fr
01 Ain 36 Indre 69 Rhone
02 Aisne 37 Indre et Loire 70 Haute Saone
03 Allier 39 Jura 71 Saone et Loire
05 Hautes Alpes 41 Loir et Cher 72 Sarthe
08 Ardennes 42 Loire 75 Paris
09 Ariege 45 Loiret 77 Seine et Marne
10 Aube 50 Manche 78 Yvelines
11 Aude 54 Meurthe et
Moselle 79 Deux Sievres
12 Aveyron 55 Meuse 82 Tarn et Garonne
16 Charente 57 Moselle 84 Vaucluse
19 Correze 58 Nievre 86 Vienne
2A Corse Sud 59 Nord 88 Vosges
2B Haute Corse 60 Oise 89 Yonne
21 Cote d’Or 61 Orne 90 Territoire de Belfort
24 Dordogne 63 Puy de Dome 91 Essonne
25 Doubs 64 Pyrenees
Atlantique 92 Hauts de Seine
26 Drome 65 Hautes Pyrenees 93 Seine St Denis
27 Eure 66 Pyrenees
Orientales 94 Val de Marne
32 Gers 67 Bas Rhin
35 Ille et Vilaine 68 Haute Rhin
Section Continues
Printer Preparation
pg. 7
Connecting the
Printer pg. 26
Radio Regulatory
Information pg. 30
RP4T Printers
pg. 34 Maintenance pg. 35 Troubleshooting
pg. 37
Specications
pg. 42 Appendices pg. 45 Index pg. 51
P4T Overview-
pg. 5
Manual
Introduction pg. 4
P4T/RP4T
User Guide
33
RFID Encoder
The following section only applies when the RFID encoder is in-
stalled in an RP4T printer. The RFID encoder may be installed in con-
junction with either the Bluetooth or 802.11g radio options detailed
previously, but may not be installed with the Bluetooth/802.11g
dual radio option.
RP4T Series printers will have the fifth character of the Product
Configuration Code (PCC), which determines country compatibility
for the RFID encoder, per the following table:
RFID option PCC
digit “5” Printer Model
No RFID 0 P4T
US U RP4T
EU 1 RP4T
Australia 2 RP4T
Taiwan 6 RP4T
New Zealand 8 RP4T
Brazil 9 RP4T
China A RP4T
Malaysia B RP4T
Phillipines C RP4T
India D RP4T
El Salvador E RP4T
Isreal F RP4T
Japan G RP4T
Korea H RP4T
The following table lists FCC and Industrie Canada ID numbers
for the various configurations of RP4T printer radio options.
Conguration FCC ID: Industrie Canada ID:
RFID Encoder I28RFID-M5ECZ-01 3798B-M5ECZ01
RFID Encoder & 802.11b/g Option K I28RFID-R4LANG-01 3798B-R4LANG01
RFID Encoder & 802.11b/g Option G 128RFID-R4CXNG-01 3798B-R4CXNG01
RFID Encoder & BT2.0 Radio I28RFID-M5ZBR4-01 3798B-M5ZBR401
Caution • Exposure to Radio Frequency Radiation.
The radiated output power of this RFID encoder is far below
the FCC radio frequency exposure limits. The RFID encoder
operates within guidelines found in radio frequency safety
standards and recommendations. Do not use the printer
in an unauthorized manner.
Printer Preparation
pg. 7
Connecting the
Printer pg. 26
Radio Regulatory
Information pg. 30
RP4T Printers
pg. 34 Maintenance pg. 35 Troubleshooting
pg. 37
Specications
pg. 42 Appendices pg. 45 Index pg. 51
P4T Overview-
pg. 5
Manual
Introduction pg. 4