Zebra Z4Mplus Users Manual Technical Writer II

2014-12-11

• Your feedback helps us improve our documents to better serve you!
  • Product and Personal Information
  • Document Usability
  • Additional Comments
• Product Improvements
• FCC Compliance Statement
• Canadian DOC Compliance Statement
• Liability Disclaimer
• Limitation of Liability
• Copyrights
• DECLARATION OF CONFORMITY
  • Zebra Technologies Corporation
    • For Home, Office, Commercial, and industrial use
• Printer Products
  • Supplies Products
  • Warranty Exclusions & Conditions Statement
• Printer Software and Firmware License Agreement
• Contacts
  • Support
• About this Document
• Document Conventions
• Related Documents
• Inspect the printer
  • Report Damage
  • Storage
• Z4Mplus and Z6Mplus Printer Overview
  • Front Panel
  • Printer Side View
• Before You Begin
  • Media
  • Ribbon
  • Types of Media
    • Non-Continuous Web Media
    • Non-Continuous Black Mark Labels
    • Continuous Media
  • Print Mode
• Load Media and Ribbon
  • Load the Media
• Load the Ribbon
• Calibration
  • Auto Calibration
• Printhead Pressure Adjustment
  • Set Printhead Pressure
• Rewind Media Alignment
• Configuration Label
  • Print a Configuration Label
• Troubleshoot Printing Problems
• Basic Configuration
  • Basic Configuration Process
• Position the Label Sensor
  • Reflective Sensor
    • Adjust the Reflective Sensor
    • Transmissive Sensor
  • Configure the Software or Printer Driver
• System Considerations
  • Interfaces
    • Standard Interfaces
  • Cable Requirements
• Printer Overview
  • Front Panel
    • Front Panel Keys
    • Front Panel Lights
• Load Roll Media
  • Tear-Off Mode
  • Cutter Mode
  • Peel-Off Mode
  • Liner Take-Up Mode
    • Liner Removal
  • Rewind
    • Peel Mode
    • Liner Removal
    • Rewind Mode
    • Media Removal
• Load Fanfold Media
• Load the Ribbon
  • Remove the Ribbon
• Configuration
  • Enter Setup Mode
  • Change Password-Protected Parameters
  • Leave the Setup Mode
• Configuration and Calibration Sequence
• Cleaning Procedures
  • Clean the Exterior
  • Clean the Interior
    • Clean the Printhead and Platen Roller
    • Avoid abrasion
    • Clean the printhead regularly
  • Clean the Sensors
  • Clean the Rewind Option
  • Clean the Peel-Off Assembly
  • Clean the Cutter Module
• LCD Error Conditions and Warnings
  • Error Conditions
    • Error condition — RIBBON OUT
    • Error condition — RIBBON IN
    • Error condition — PAPER OUT
    • Error condition — HEAD OPEN
  • Warnings
    • Warning — HEAD OVER TEMP
    • Warning — HEAD UNDER TEMP
    • Warning — CUTTER JAM
    • OUT OF MEMORY*
• Print Quality Problems
  • General print quality issues
  • Gray lines on blank labels with no consistent pattern
  • Light, consistent vertical lines running through all labels
  • Intermittent creases on the left and right edges of the label
  • Wrinkled ribbon
  • Calibration
  • Communication Problems
• Printer Diagnostics
  • Power-On Self Test
  • Additional Printer Self Tests
  • Cancel Self Test
  • Pause Self Test
  • Feed Self Test
  • Communications Diagnostics Test
    • Loading Factory Defaults
• General Specifications
• Printing Specifications
• Media Specifications
• Ribbon Specifications
• Options
• Zebra Programming Language (ZPL II)
• Bar codes
• AC Power Cord
  • Power Line Cord Specifications
• Printer Interface Technical Information
  • Serial Data Communications
    • Hardware Control Signal Descriptions
  • Cable Specifications
    • RS-232 Serial Data Port
• Parallel Data Port
  • Parallel Interface
    • Parallel Cabling Requirements
  • Parallel Port Interconnections
• Memory Cards
  • PCMCIA Card
    • Install the PCMCIA Card
• Extend the Life of Your Printhead with SaveaPrinthead Cleaning Film
  • Recommended for all Zebra printers
    • Challenge
    • Preventive Maintenance
    • Avoid the Contributing Factors to Premature Printhead Failure
    • Save-a-Printhead Cleaning Film
  • Use Save-a-Printhead Cleaning Film
  • How to Order Cleaning Film Kits