Zeeva EP-0546 BT LED WRAP EARBUDS AST User Manual IM EP 0546

Zeeva International Limited BT LED WRAP EARBUDS AST IM EP 0546

User Manual

Headset Overview3. Activate the Bluetooth function on your phone within range and select “BT LED WRAP EARBUD” from the list shown.4. The LED lights in blue when paired successfully.Attention: If the pairing is not successful within 5 minutes, the headset will power off, please repeat the pairing procedures to try again. Pair BT LED WRAP EARBUDS with your mobile device1. Keep the distance between your wireless headset and mobile phone (or other devices) within 32.8 Feet.2. Power on the BT LED WRAP EARBUDSReconnect BT LED WRAP EARBUDS to your mobile deviceWhen powered on, the headset will automatically connect with the last successfully paired device.Disconnect the headset from your mobile deviceLeave the headset 60ft away from your mobile phone or further.Power off the headset; orSwitch off the Bluetooth on your mobile phone; orAnswer/Reject a callEnd a callWhen you receive a call, press the On/Off Button once to accept the call,or answer the call normally via your mobile phone.Long press On/Off Button to reject a callPress the On/Off Button once to end the call or hang up your mobile phone.Technical specificationFAQFCC ID: 2ADM5-EP-0546Made Exclusively for Five BelowDistributed by Zeeva International LimitedSuite 1006C-8, 10th Floor, Exchange Tower, 33 Wang Chiu Road, Kowloon Bay,Hong Kong, ChinaKeep all relevant information for future referenceFCC STATEMENT1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) This device may not cause harmful interference.(2) This device must accept any interference received, including interference that may cause undesired operation.2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:- Reorient or relocate the receiving antenna.- Increase the separation between the equipment and receiver.- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.- Consult the dealer or an experienced radio/TV technician for help.RF warning statement:The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.LED indicator light turns red when charging your headsetLED indicator light turns blue when your headset are fully chargedShort press + Button to advance to next songLong press + Button to turn up volumeLong press - Button to turn down volumeShort press - Button to go back to previous songFunctionsCharging your headsetHeadset OverviewPower On/OffLED Micro USB Charging Cable:USB PlugMicro USB PlugPower onPress and hold down the On/Off Button for 3 seconds and the LED will flash in red and blue alternately.Power offPress and hold down the On/Off Button for 4 seconds and the LED will turn off.LED Flash Power On/OffLED Power on Double click the Vol+ button to switch On the LED flash.LED Power offDouble click the Vol+ button to switch Off the LED flash.If the BT LED WRAP EARBUDS cannot be paired with your device, please try the following:Ensure that your headset are in pairing mode or reconnection mode.Ensure that Bluetooth search function of your mobile device is activated.If the BT LED WRAP EARBUDS will not turn on:Make sure the headset are fully charged.Can I change the battery for the headset?BT LED WRAP EARBUDS use a built-in non-detachable battery whichcannot be removed.If the BT LED WRAP EARBUDS cannot be recharged:If you use a power outlet, ensure that the power supply is connected securely and the outlet works. If you use a computer, ensure that it is connected and the USB port is powered.-The input voltage to the product is 5V 1A.-In order to charge the product in safe manner and reliable conditions, please only adopt certified appropriate charger/ adapter for charging the product.-Only charge the product at ambient temperatures between 10 deg °C/ 50 deg °F and 40 deg °C/104 deg °F.-Do not heat above 70 deg °C/158 deg °F, eg. Do not expose to sunlight or throw into fire.-Switch off the product after use.-Please note that we won’t take any responsibility for any wrong operation (e.g. Voltage higher than 5V) as this may result in severe injury or loss of property, and we cannot control the operating process during the time the user using this product.-In extreme cases, abuse or misuse of Lithium battery pack can lead to explosion, heat generation, fire development or smoke development.Safety instructions for the lithium battery and charging the productThank you for purchasing the BT LED WRAP EARBUDS.This manual provides more information about the wireless headset, please read the instructions before using. INSTRUCTION MANUALVol-/Previous SongOn/Off ButtonPlay/Pause MusicAnswer/End CallVol+/Next SongFront: Side:MicrophoneMicro USB Charging PortPackage ContentsBT LED WRAP EARBUDS x 1 pcMicro USB Charging Cable x 1 pcUser Manual x 1BT LED WRAP EARBUDSImpedance: 32 Ohms Sensitivity: 95 dB +/- 3 dBFrequency Response: 20 Hz - 20 KHzPower Supply: Li-ion Battery 3.7V 60 mAh Playing Time: 2-3 HoursCharging Time: 2 HoursBluetooth Range: 32.8 FeetMicro USB cable included.

Navigation menu