Zhongshan K mate General Electronics BTE010 Bluetooth mono headset User Manual 5 BTE010 User s Manual revised

Zhongshan K-mate General Electronics Co., Ltd Bluetooth mono headset 5 BTE010 User s Manual revised

UserManual.wiki >

Zhongshan K mate General Electronics >

BTE010 User Manual

Users Manual

BTE010 Bluetooth mono headset User’s manual  Brief introduction………………………………………..1 1. Bluetooth wireless communication technology…………………...1 2. About BTE010…………………………………………….………….1  Before use....……………………………………………..1 1. Overview…………………………………………………………..….1 2. Charging the battery of BTE010…………………………..…….....2  Basic operation………………………………………….3 1. Switching on/off BTE010………………………………….……...…3 2. Pairing BTE010 with a Bluetooth cell phone………….……….….3 3. Wearing BTE010……………………………………………………..4 4. Making calls with BTE010…………..………………………………4 5. LED indicator………………………………………………………….5 6. Indication tone……………………………………………………..…5  Care and maintenance……………………………….…5  FAQs…………………………………………………….…6  Specifications…………………………………………….6

Welcome to use this Bluetooth mono headset, BTE010. Please read this user’s manual carefully before use.  Brief introduction 1. Bluetooth Wireless communication technology Bluetooth is a standard of close range radio-communication technology that was drawn up by Ericsson, IBM, Intel, Nokia and Toshiba. With Bluetooth technology, we can achieve the highest transmission rate among cell phones, computers, printers, PDAs and other devices. The max transmission range of class 2 is 10 meters while the max transmit range of class 1 can reach up to 100 meters. 2. About BTE010 BTE010 is a Bluetooth mono headset. It has the following features:  Answer call, end call and reject call  Redial last number  Voice dial (This function needs to be supported by your cell phone)  Adjust the volume  Call transfer between BTE010 and your Bluetooth cell phone  Microphone mute  Noise filtering function to ensure a clearer conversation  Before using 1. Overview

1 Multi-function button (MFB Switch on/off, dial number, answer call, reject call and end call2 Vice microphone noise filtering 3 LED indicator4 Ear cap5 VOL + —Volume up 6 VOL - —Volume down7 Main microphone8 Charging port9 Loudspeaker10 Ear hook 2. Charging the battery of BTE010 First use—You must charge the battery of BTE010 fully before first use. Low power—When you hear a string of indication tones every 30 seconds and see the red LED flashing, the battery is low power and needs to be charged. The charging steps are as follows: Step1: Connect the charger or charging cable to standard power outlet; Step2: Connect the end of charger or charging cable to charging port of BTE010; Step3: The red LED is on while charging. It takes about 1.5 hours to fully charge the battery; Step4: When charging has completed, the blue LED will switch on. Warning: 1) The battery is recycled. 2) Batteries (battery pack or batteries installed) shall not be exposed to excessive heat such as sunshine, fire or the like.

 Basic operation 1. Switching on/off BTE010 Remark: In order to save power, BTE010 will switch off automatically if no devices can be connected after 5 minutes. 2. Pairing BTE010 with a Bluetooth cell phone You have to pair BTE010 with your Bluetooth cell phone before first use. Please make sure your cell phone is Bluetooth-enabled. Specific pairing steps may vary with different cell phones. Please refer to your cell phone user’s manual for further information. The general pairing steps are as follows: 1) Keep BTE010 and Bluetooth cell phone within 1 meter when pairing; 2) Make sure BTE010 is off, otherwise switch it off first; 3) Press and hold MFB button for about 6 7 seconds, until the red and blue LEDs are flashing alternately. BTE010 successfully entered pairing mode; 4) Switch on your cell phone’s Bluetooth function and search for Bluetooth devices. After the search is completed select “BTE010” from the Bluetooth device list; 5) According to the indication, enter password or PIN No:”1234” and press ” Yes” or “confirm”; 6) After successful pairing, select “BTE010” from the Bluetooth device list, and press “connect”. The LED indicator will flash twice every 5 seconds if connected successfully. Remarks:  Pairing mode will last 2 minutes. BTE010 will switch to standby mode automatically if it can’t connect to any device after 2 minutes. If you want to continue pairing BTE010 with a Bluetooth device, please switch off BTE010 first and then re-pair according to steps 1 6 mentioned above.  BTE010 can remember 8 paired devices. When the number of devices exceeds 8, the first one will be replaced.  Every time you switch on BTE010, and it doesn’t connect to any device, press MFB button once, BTE010 will connect to the last connected device.  Every time you switch on BTE010, it will connect to the last connected device automatically. If you want to pair it with other devices, please switch off the Bluetooth function of the last connected devices first and pair BTE010 with the new device according to steps 1 6 mentioned above. Function Operation LED indicator Indication tone Switching on BTE010 Press and hold MFB button for 3 5 seconds Blue LED is on for 1 second Four rising tones Switching off BTE010 Press and hold MFB button for 3 5 seconds Red LED is on for 1 second Four falling tones Entering pairing mode Make sure BTE010 is off, then press and hold MFB button for 6 7 seconds Red and blue LEDs flash alternately Six falling tones

3. Wearing BTE010 The headset is suitable for both ears, because you can freely turn the ear hook. After putting on the headset, align the microphone towards the user’s mouth to get the best conversation quality. 4. Making calls with BTE010 Function Operation Indication tone Voice dial Press and hold MFB button for 2 seconds Two short tones Redial last number Double click MFB button One short tone Cancel calling Short press MFB button One short tone Volume up Short press VOL + button One short tone Volume down Short press VOL– button One short tone End call Short press MFB button One short tone Answer call Short press MFB button One short tone Reject call Press and hold MFB button for about 2 seconds One long “DU” tone and then two falling tones Call transfer (from headset to cell phone) Press and hold VOL+ button for about 2 seconds One short tone Call transfer (from cell phone to headset) Press and hold VOL+ button for about 2 seconds One short tone Microphone mute Short press VOL+ button and VOL- button simultaneously Two rising tones Cancel mute Short press VOL+ button and VOL- button simultaneously Two falling tones Re-connect Short press MFB button Two long “DI” tones Warning: Don’t turn up the headset’s volume too much as this may cause hearing loss. Remarks:  Not all cell phones support all functions listed above. Please refer to your cell phone’s user’s manual for further information.  When the volume is adjusted to max. you will hear a rising “DU” tone; when the volume is adjusted to Min. you will hear a falling “DU” tone.  When pressing the answer button on some cell phones, the call will be transferred to the cell phone. You have to transfer the call to BTE004 manually then. Please refer to your cell phone’s user’s manual for further.  Please be advised to switch off your cell phone’s Bluetooth function if you are not going to make a call with BTE010 in anytime soon.

5. LED indicator 1) While it is charging LED indicator Status of the headset Red LED is on Charging in progress Blue LED is on Charging finished 2) While it is not charging LED indicator Status of the headset Red and blue LEDs flash alternately Pairing mode Blue LED flashes once every 2 seconds Standby mode (not connect to a Bluetooth device) Blue LED flashes twice every 5 seconds Standby mode (connected to a Bluetooth device) Blue LED flashes quickly Incoming call/calling Blue LED gradually turns on and off Conversation mode Red LED flashes Low power 6. Indication tone Indication tone Status of the headset Two continuous DU tones every 10 seconds Microphone mute A string of indication tones every 30 seconds Low power  Care and maintenance Read the following recommendations before using BTE010. Following these you will be able to enjoy our product for many years.  Keep it dry and don’t take it to damp places to avoid the product’s internal circuit being affected.  Keep the product away from direct sunlight or hot places. High temperatures will shorten the life of electronic devices, destroy the battery or distort certain plastic parts.  Don’t expose the product to cold areas. It may damage the internal circuit board.  Don’t try to disassemble the product as it may get damaged if you are not professional.  Don’t let it fall down onto the floor or other hard surfaces. The internal circuit might get damaged.