Zhongshan K mate General Electronics BTH023 Bluetooth Stereo Headset User Manual BTH023 User s Manual

Zhongshan K-mate General Electronics Co., Ltd Bluetooth Stereo Headset BTH023 User s Manual

UserManual.wiki >

Zhongshan K mate General Electronics >

BTH023 User Manual

User Manual

BTH023 Bluetooth stereo headset User’s manual

Contents  Brief introduction…………...…………………………..…....1 1. Bluetooth wireless communication technology……………….…....1 2. About BTH023…………………………………………………...1  Before use……………………………………………………..2 1. Overview…………………………………………………...……2 2. Charging for Headset..……………………………………………3  Getting started……..…………………………………………3 1. Turning on/off the headset…………....………………………......3 2. Pairing headset with Bluetooth devices…….…………………..….4 1) How to enter pairing mode………………….………………….4 2) Pairing headset with Bluetooth cell phone…………………..….4 3) Pairing headset with Bluetooth transmitter………..…………....5 4) Pairing headset with Multi-devices………….………………….5 3. Reconnecting the headsets with devices………………………....6 4. Making a call with the headset………………………………….6 5. Playing music……………………………………………….…...9 6. LED indicator…………………………………………………..9 7. Indication tone………………………………………………….10 8. Factory Reset………………………………………………..….10  Care and maintenance……………………………..………..10  FAQs……………………………………...…………………..11  Specification……………………………...………………..…12

3) Easy to switch between the call and music, you will not miss the incoming call during listening to music. 4) Every time the headset is turned on, it will connect to last connected device automatically. Note: In order to complete above function, the Bluetooth profiles of paired device must be same as the headset. And even though the paired device and the headset support the same Bluetooth profiles, functions may vary due to specification differences of the paired devices.  Before use 1. Overview 1 LED indicator 5 Multi-functions button(MFB): pause /play 2 Charging jack 6 Volume down/next song 3 Built-in microphone 7 Right speaker 4 Volume up/last song 8 Left speaker 2

2. Charging for headset The headset comes with a built-in rechargeable battery, prior to using it, it is recommended to charge the battery fully for the first time. When the headset is low power, the headset emits five “Dong” tones every 5 minutes and the red LED flashes instead of blue LED. Please recharge the battery of the headset. The way of charging as following: Using USB cable 1. Plug the special charging clip into the charging jack of headset, make it clip the headset as pictures shown : 2. Plug another side of cable to the USB port of PC Red light on: Charging Red light off: Finish charging 3. It will takes about 2 hours to finfish charging Remarks: 1) The battery is recyclable. 2) Batteries (battery pack or batteries installed) shall not be exposed to excessive heat place, such as sunshine, fire or the like.  Getting started 1. Turning on/off the headset Functions Operation LED indicator Turning on Press and hold MFBbutton about 4 seconds until blue LED flashesBlue LED on one second Turning off Press and hold MFB buttonabout 4 seconds until red LED flashesRed LED on one second Remark: In order to save power, the headset will turn off automatically if no devices can be connected after 5 minutes. 3

2. Pairing the headset with Bluetooth devices 1) How to enter pairing mode Functions Operation LED indicatorEntering pairing mode Ensure the headset is off, otherwise please turn it off first. And then press and hold MFB button about 8 seconds until red and blue LED flash alternatelyRed and blue LED flash alternately Remark: Pairing mode will last 2 minutes. If no devices can be connected after 2 minutes, it will return to standby mode automatically. 2) Pairing headset with Bluetooth cell phone Prior to using the headset for the first time, you have to pair it with a Bluetooth-enabled cell phone. The pairing procedures are subject to different models of cell phones. Please refer to your cell phone user’s manual for further information. The general pairing procedures are as follows: 1) Keep your headset and phone within 1 meter when pairing; 2) Make the headset enter pairing mode (please refer to “How to enter pairing mode); 3) Activate your cell phone’s Bluetooth function and set your cell phone to search for Bluetooth devices within range, and select “BTH023” from the list of devices shown; 4) According to the indication, enter password or PIN No: “0000”. ( If the mobile phone supports Bluetooth V2.1, password is not required.). If prompted by your cell phone to connect, select “Yes” (this will vary among cell phone models); 5) After successful paired, choose and connect “BTH023” from the list of devices shown on cell phone; 6) After successful connecting, blue LED of headset will flashes twice every 4 seconds Remarks:  If pairing is failed, please turn off the headset first and then re-pair according to steps 1～6 mentioned above.  After pairing is successful, the headset and the cell phone will remember each other, they will no need to re-pair next time. The headset can remember 8 paired devices, when the number of paired devices exceeds 8, the first one will be replaced. 4

 Every time the headset is turned on, it will connect to last connected device automatically. If you want to pair it with other devices, please turn off the Bluetooth function of last connected devices first and pair the headset with the new device according to steps 1～6 mentioned above. 3) Pairing headset with Bluetooth transmitter You can connect the headset to a Bluetooth transmitter to enjoy music wirelessly. Hereby take BTT005 (Bluetooth transmitter, not included) for example. The pairing steps are as follows: 1) Keep your headset and transmitter within 1 meter when pairing; 2) Make the headset enter pairing mode (Please refer to “How to enter pairing mode); 3) Turn on the Bluetooth transmitter and make it enter pairing mode. It will search for Bluetooth devices automatically and send a pairing request; 4) When the headset requests to enter a PIN No., the transmitter will response “0000” automatically; 5) After successful pairing and connecting, blue LED of the headset flashes twice every 4 seconds. Remarks:  The pairing password of the headset is “0000”. So, the headset can only pair with a Bluetooth transmitter whose pairing password is “0000”.  If pairing still fails after several tries, please refer to the Bluetooth transmitter’s user’s manual for further information. 4) Pairing headset with Multi-devices The headset can connect with two Bluetooth devices at most. If you want to finish the Multi-pairing, please refer to the following steps: 1) Firstly, pair and connect the headset with a Bluetooth device one (refer to “pairing the headset with a Bluetooth cell phone); 2) Turn on the headset and make it enter pairing mode again, make the headset pair and connect with Bluetooth device two (refer to “pairing the headset with a Bluetooth cell phone); 5

3) Operate Bluetooth device one to connect with headset. Now, the headset has already connected with two devices. The headset will connect with last connected two devices automatically when you turn it on again. Remarks:  After successful multi-pairing, the paired devices will remember each other, they will no need to pair next time.  The headset will connect with last connected two devices automatically when you turn it on again.  Turn off multi-pairing:in the status of standby mode（not connected device）, long press MFB and volume down “—” button, and release it until hear four fall tone.  Turn on multi-pairing:in the status of standby mode（not connected device）, long press MFB and volume up “+” button, and release it until hear 4 raise tone. 3. Reconnecting the headset with devices 1) Automatic connecting Every time the headset is turned on, it will connect to last connected device automatically. 2) Manual connecting When the headset is in standby mode and does’t connect to a device, short press MFB button once, it will connect to last connected device. Remarks:  Before connecting to a Bluetooth device, please turn on the Bluetooth function of Bluetooth device.  On some Bluetooth devices, take some Nokia cell phones for example, you have to allow automatic connecting in the cell phone’s settings. Please refer to your cell phone’s manual for further information. 4. Making a call with the headset 1) Basic operation Functions Status of headset Operation Cancel a call Calling Short press MFB once Answer a call Incoming ringing Short press MFB once 6

Reject a call Incoming ringing Long press MFB about 2 seconds and release it until listen a tone End a call During a call Short press MFB once Volume up During a call Short press+ button Volume down During a call Short press — button Transfer conversation to mobile phone During a call Long press MFB about 2 seconds Transfer conversation to headset During a call Long press MFB about 2 seconds Microphone mute During a call Long press volume up “+” button about 2 seconds Cancel mute During a call (microphone mute) Long press volume down “+” button about 2 seconds Voice dial Standby mode (connected device) Short press MFB and volume up “+” button simultaneously Redial the last number Standby mode (connected device) Double click MFB button Remove paired list Charging status In the status of charging, long press volume up “+” button, red and blue LED will flashes simultaneously and you will hear four “dong” tone Warning: Excessive pressure form earphones and headphones can cause hearing loss. Note:  Not all the mobile phones support all the functions listed above. Please refer to your mobile phone user’s manual.  Different function and prompt tone according to different mobile phone. 7

 When the volume is adjusted to max or min, you will hear one prompt tone.  When pressing the answer button on some mobile phones, the call will be transferred to the mobile phone. You can switch the call to the headset by using the conversation switch button or through operating on the mobile phone. Please refer to your mobile phone user manual for further information. 2) Three-ways call operation Functions Status of headsets Operation Answer new call and end current call There are second incoming call Short press MFB once Answer new call and retain current call There are second incoming call Double click MFBbutton Switch calls Keep conversation Double click MFBbutton End current call and switch retain call Keep conversation Short press MFB once 3) Making a call with two headsets Functions Status of headset OperationRetain phone 1 call and answer phone 2 call During phone 1 call, phone 2 is incoming callDouble click MFB button End phone 1 call and answer phone 2 call During phone 1 call, phone 2 is incoming callShort press MFB button once Switch call During call, one of phone call is retainedDouble click MFB buttonEnd current phone call, back to retain phone call During call, one of phone call is retained Short press MFB button once 8

Blue LED flashes twice every 4 seconds Connect with deviceBlue LED flashes continuouslyCalling/incoming callBlue LED flashes once quickly every 2 seconds During a callRed LED flashes instead of blue LED Low battery 7. Indication tone Indication tone Status of the headsetContinuous two prompt tone every 10 secondsConversation mode and microphone muteFive “dong” warning tone every 5 minutes Low battery 8. Factory Reset In the status of charging, long press volume up “+” button about 4 seconds and release it until the red and blue LED flashes simultaneously, you will hear 4 “dong” tone. Remarks: After factory reset, the paired list of headset will be deleted. After turn it on again, the headset will enter pairing mode automatically, and you need to re-pair and connect with Bluetooth devices.  Care and maintenance Read the following recommendations carefully before using BTH023. Following these you will be able to enjoy this product for many years.  Keep it dry and don’t put it in the dump place to avoid the product’s internal circuit being affected.  Keep the product away from direct sunlight or hot places. High temperatures will shorten the life of electronic devices, destroy the battery or distort certain plastic parts.  Don’t expose the product to cold areas. It may damage the internal circuit board.  Don’t try to disassemble the product as it may get damaged if you are not professional. 10

 Don’t let it fall down onto the floor or other hard surfaces. The internal circuit might get damaged.  Don’t use intensive chemical products or detergent to clean the product.  Don’t scratch the surface with sharp things.  Don’t use this product during strenuous exercise. It may damage the product if the sweat into product. In case the product does’t function properly, send it to the store you bought it. The staff will help you to solve the problem  FAQs 1. What does it mean when red LED flashes instead of blue LED? Battery is low power, need to be recharged. 2. Why is the red LED off when charging? a) Please make sure the charging device connect with headset Well; b) You did’t use the headset for a long time, the battery may dry up. At this time, you have to charge the battery for 30 minutes, and then the red LED will be ON. 3. How far is the effective rang between the headset and mobile phone? According to the Bluetooth standard, the max available range of Class II headset is 10 meters. It varies under different environment. 4. Why my mobile phone can not search and find the headset? The mobile phone will not find the headset if headset and mobile phone are not under the pairing mode. Make sure the headset is under the pairing mode and in the effective working range, and then the headset can be paired and connected. 5. Why the headset can not hear the voice? a) Make sure the headset has been switched on; b) Make sure the volume is not too low or muted; c) Make sure the headset connects with the mobile phone correctly; d) Make sure the distance between the headset and the cell phone is in the available Bluetooth range. 11

4. Note: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment. 5. Note:: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help 12