Zhongshan K mate General Electronics BTH026 Bluetooth Stereo Headset User Manual BTH026N User s Manual

Zhongshan K-mate General Electronics Co., Ltd Bluetooth Stereo Headset BTH026N User s Manual

UserManual.wiki >

Zhongshan K mate General Electronics >

BTH026 User Manual

User Manual

BTH026N Bluetooth stereo headset User’s manual

Contents  Brief introduction…………...…………………………..…....1 1. Bluetooth wireless communication technology……………….…....1 2. About BTH026N………………………………………………...1  Before use……………………………………………………..2 1. Overview…………………………………………………...……2 2. Charging for headset..……………………………………………3  Getting started……..…………………………………………3 1. Turning on/off the headset…………....………………………......3 2. Pairing headset with Bluetooth devices…….…………………..….4 1) How to enter pairing mode………………….………………….4 2) Pairing headset with Bluetooth cell phone via Bluetooth……..….4 3) Pairing headset with Bluetooth cell phone via NFC......................5 4) Pairing headset with Bluetooth transmitter via Bluetooth ……....7 3. Reconnecting the headsets with devices………………………....7 4. Making a call with the headset………………………………...….8 5. Playing music………………………………………………..…...9 6. LED indicator………………………………………………....10 7. Indication tone………………………………………………….11 8. Factory Reset………………………………………………..….11  Care and maintenance……………………………..………..11  FAQs……………………………………...…………………..12  Specification……………………………...………………..…13

4) Easy to switch between the call and music, you will not miss the incoming call during listening to music. 5) Every time the headset is turned on, it will connect to last connected device automatically. Note: In order to complete above function, the Bluetooth profiles of paired device must be same as the headset. And even though the paired device and the headset support the same Bluetooth profiles, functions may vary due to specification differences of the paired devices.  Before use 1. Overview 2 1 Left speaker 6 Multi-functions button (MFB） 2 Right speaker 7 Volume down/next song 3 Built-in microphone 8 Charging jack 4 LED indicator 9 NFC chip 5 Volume up/previous song

2. Charging for headset The headset comes with a built-in rechargeable battery, prior to using it, it is recommended to charge the battery fully for the first time. When the headset is low power, the headset emits “Dong” tones every 5 minutes and the red LED flashes instead of blue LED. Please recharge the battery of the headset. The way of charging as following: Using USB cable 1. Plug the USB charging cable to charging jack of headset 2. Plug another side of cable to the USB port of PC Red light on: Charging Red light off: Finish charging 3. It will takes about 2 hours to finish charging Remarks: 1) The battery is recyclable. 2) Batteries (battery pack or batteries installed) shall not be exposed to excessive heat place, such as sunshine, fire or the like.  Getting started 1. Turning on/off the headset Functions Operation LED indicator Turning on Press and hold MFB button about 4 seconds until blue LED flashes Blue LED on one second Turning off Press and hold MFB button about 4 seconds until red LED flashes Red LED on one second Remark: In order to save power, the headset will turn off automatically if no devices can be connected after 5 minutes. 3

2. Pairing the headset with Bluetooth devices 1) How to enter pairing mode Functions Operation LED indicator Entering pairing mode Ensure the headset is off, otherwise please turn it off first. And then press and hold MFB button about 8 seconds until red and blue LED flash alternately Red and blue LED flash alternately Remark: Pairing mode will last 2 minutes. If no devices can be connected after 2 minutes, it will return to standby mode automatically. 2) Pairing headset with Bluetooth cell phone via Bluetooth Prior to using the headset for the first time, you have to pair it with a Bluetooth-enabled cell phone. The pairing procedures are subject to different models of cell phones. Please refer to your cell phone user’s manual for further information. The general pairing procedures are as follows: 1) Keep your headset and phone within 1 meter when pairing; 2) Make the headset enter pairing mode (please refer to “How to enter pairing mode); 3) Activate your cell phone’s Bluetooth function and set your cell phone to search for Bluetooth devices within range, and select “BTH026N” from the list of devices shown; 4) According to the indication, enter password or PIN No: “0000”. ( If the mobile phone supports Bluetooth V2.1, password is not required.). If prompted by your cell phone to connect, select “Yes” (this will vary among cell phone models); 5) After successful paired, choose and connect “BTH026N” from the list of devices shown on cell phone; 6) After successful connecting, blue LED of headset flashes twice every 4 seconds Remarks:  If pairing is failed, please turn off the headset first and then re-pair according to steps 1～6 mentioned above. 4

 After pairing is successful, the headset and the cell phone will remember each other, they will no need to re-pair next time. The headset can remember 8 paired devices, when the number of paired devices exceeds 8, the first one will be replaced.  Every time the headset is turned on, it will connect to last connected device automatically. If you want to pair it with other devices, please turn off the Bluetooth function of last connected devices first and pair the headset with the new device according to steps 1～6 mentioned above. 3) Pairing headset with a Bluetooth cell phone via NFC BTH026N support NFC function, it can quickly connect with Bluetooth cell phone via NFC, hereby take Samsung S3(Android 4.0) (Not included in accessory) for example. The general pairing procedures are as follows: 1) Please activate the Bluetooth and NFC function of cell phone; Please refer to following pictures： Touch Setting button into setting interface, activate Bluetooth function, then into More settings interface to activate NFC function. 5

2) Pairing and connecting with cell phone Please refer to following pictures: Make the NFC chip of cell phone and headset within 1 centimeter, the headset will turn on and enter pairing mode automatically, there will be a request and prompt tone on cell phone “Pair the Bluetooth device”, according to prompt tone, click “Yes” to confirm. Now, the headset has already paired and connected with cell phone. Remarks:  The screen of cellphone must be in unlocked mode during pairing via NFC  The NFC chip of cell phone and headset must be in 1 centimeter during pairing  Under the headset’s status of turn off, standby mode(not connect with device), pairing mode, you can pair it with cell phone via NFC 6

4) Pairing headset with Bluetooth transmitter via Bluetooth You can connect the headset to a Bluetooth transmitter to enjoy music wirelessly. Hereby take BTT005 (Bluetooth transmitter, not included in accessories) for example. The pairing steps are as follows: 1) Keep your headset and transmitter within 1 meter when pairing; 2) Make the headset enter pairing mode (Please refer to “How to enter pairing mode); 3) Turn on the Bluetooth transmitter and make it enter pairing mode. It will search for Bluetooth devices automatically and send a pairing request; 4) When the headset requests to enter a PIN No., the transmitter will response “0000” automatically; 5) After successful pairing and connecting, blue LED of the headset flashes twice every 4 seconds. Remarks:  The pairing password of the headset is “0000”. So, the headset can only pair with a Bluetooth transmitter whose pairing password is “0000”.  If pairing still fails after several tries, please refer to the Bluetooth transmitter’s user’s manual for further information. 3. Reconnecting the headset with devices 1) Automatic connecting Every time the headset is turned on, it will connect to last connected device automatically. 2) Manual connecting When the headset is in standby mode and doesn’t connect to a device, short press MFB button once, it will connect to last connected device. Remarks:  Before connecting to a Bluetooth device, please activate the Bluetooth function of Bluetooth device.  On some Bluetooth devices, take some Nokia cell phones for example, you have to allow automatic connecting in the cell phone’s settings. Please refer to your cell phone’s manual for further information. 7

4. Making a call with the headset 1) Basic operation Functions Status of headset Operation Cancel a call Calling Short press MFB once Answer a call Incoming call ringing Short press MFB once Reject a call Incoming call ringing Long press MFB about 2 seconds and release it until listen a tone End a call During a call Short press MFB once Volume up During a call Short press + button Volume down During a call Short press — button Transfer conversation to mobile phone During a call Long press MFB about 2 seconds Transfer conversation to headset During a call Long press MFB about 2 seconds Microphone mute During a call Long press volume up “+” button about 2 seconds Cancel mute During a call (microphone mute) Long press volume up “+” button about 2 seconds Voice dial Standby mode (connected device) Short press MFB and volume up “+” button once simultaneously Redial the last number Standby mode (connected device) Double click MFB button Warning: Excessive pressure from earphones and headphones can cause hearing loss. Note:  Not all the mobile phones support all the functions listed above. Please refer to your mobile phone user’s manual. 8

 Different function and prompt tone according to different mobile phone.  When the volume is adjusted to max or min, you will hear one prompt tone.  When pressing the answer button on some mobile phones, the call will be transferred to the mobile phone. You can switch the call to the headset by using the conversation switch button or through operating on the mobile phone. Please refer to your mobile phone user manual for further information. 2) Three-ways call operation Functions Status of headsets Operation Answer new call and end current call There are second incoming call Short press MFB once Answer new call and retain current call There are second incoming call Double click MFB button Switch calls Keep conversation Double click MFB button End current call and switch retain call Keep conversation Short press MFB once 5. Playing music When the headset connects to a mobile phone or Bluetooth transmitter which supports A2DP, you can enjoy music wirelessly through the headset. Functions Status of the headset Operation Volume up Playing music Short press “+”button Volume down Playing music Short press “―”button Last song Playing music Long press “+”button Next song Playing music Long press “―”button Pause Playing music Short press MFB once play Pausing Short press MFB once 9

7. Indication tone Indication tone Status of the headset Two prompt tone every 10 seconds during a call Microphone mute Five “dong” warning tone every 5 minutes Low battery 8. Factory Reset In the status of charging, long press volume up “+” button about 4 seconds and release it until the red and blue LED flashes simultaneously, you will hear 4 “dong” tone. Remarks: After factory reset, the paired list of headset will be deleted. After turn it on again, the headset will enter pairing mode automatically, and you need to re-pair and connect with Bluetooth devices.  Care and maintenance Read the following recommendations carefully before using BTH026N. Following these you will be able to enjoy this product for many years.  Keep it dry and don’t put it in the dump place to avoid the product’s internal circuit being affected.  Keep the product away from direct sunlight or hot places. High temperatures will shorten the life of electronic devices, destroy the battery or distort certain plastic parts.  Don’t expose the product to cold areas. It may damage the internal circuit board.  Don’t try to disassemble the product as it may get damaged if you are not professional.  Don’t let it fall down onto the floor or other hard surfaces. The internal circuit might get damaged.  Don’t use intensive chemical products or detergent to clean the product.  Don’t scratch the surface with sharp things.  Don’t use this product during strenuous exercise. It may get damaged by sweat. In case the product doesn’t function properly, send it to the store you bought it. The staff will help you to solve the problem 11

 Specifications Bluetooth version Bluetooth V4.0 Bluetooth profiles Headset, Hands free, A2DP, AVRCP Operating distance 10meters Headset music time About 4.5 hours Headset talk time About 5 hours Headset charging time About 2 hours Dimension Headset: 37x16.3x27.7 mm Cable: about 500mm Weight About 12.6 g Notes: Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions : (1) this device may not cause harmful interference, and (2) this device must accept any interference received including interference that may cause undesired operation.

lithium battery： CAUTION RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS TO THE INSTRUCTIONS Headset: To prevent possible hearing damage,do not listen at high volume levels for long periods 13