Chill Tap Sparkling CO2 Disposable Gas Bottle Replacement Instructions V1.00
Chilltap Sparkling Co2 Disposable Gas Bottle Replacement Instructions V1.00 ChillTap sparkling_CO2 Disposable gas bottle replacement Instructions_v1.00 ChillTap sparkling_CO2 Disposable gas bottle replacement Instructions_v1.00 zipwater_ commercial instruction manuals zipwater.chilledwater zipwater.uk.products zipwater.uk zip-website-media
2016-08-19
: Zip Water Chilltap Sparkling Co2 Disposable Gas Bottle Replacement Instructions V1.00 ChillTap sparkling_CO2 Disposable gas bottle replacement Instructions_v1.00 zipwater_ residential instruction manuals zipwater.chilledwater zipwater.uk.products zipwater.uk
Open the PDF directly: View PDF 
.
Page Count: 2
| Download | |
| Open PDF In Browser | View PDF |
CO2 Disposable Cylinder Replacement Guide. Important! Read this guide before attempting to change your CO2 bottle. CO2 - Disposable Cylinder. Compressed Carbon Dioxide, Food Grade. Cylinder Specifications: • UN No: 1013 • Code: ZT400 • Contents: 1,000g • Class 2.2 • Volume: 2.2 litres • Tare: 1,745g CO2 Cylinder Warnings: • Pressurised container. • Protect from sunlight. • Contains gas under pressure, may explode if heated. • Do not expose to temperatures exceeding 50°C. • Do not pierce or burn, even after use. • Do not refill – non rechargeable. • Ensure cylinder is empty before disposal. • Do not expose to naked flame or any incandescent material. • Keep out of reach of children. • High concentration of gas may cause asphyxiation. • Use only in ventilated areas. • Use only in an upright position. • This bottle must be used with the approved pressure regulator. • Avoid shock. • Use according to MSDS. (Material Safety Data Sheet). CO2: Before use carefully read the product label. Use of safe work practices are recommended to avoid eye or skin contact and inhalation. Observe good personal hygiene, including washing hands before eating. Prohibit eating, drinking and smoking in contaminated areas (eg. if the container is damaged). Storage: Do not store near sources of ignition or incompatible materials. Cylinders should be stored below 50°C in a secure area, upright and restrained to prevent cylinders from falling. Cylinders should also be stored in a dry, well ventilated area constructed of non-combustible material with firm level floor (preferably concrete), away from areas of heavy traffic and emergency exits. NOTE: Care must be taken when working with high pressure C02, and in no cases should the normal operating pressure of 0.27 MPa (2.7 bar) be exceeded. WARNING: A gas cylinder containing 1kg of CO2 should be installed in a well ventilated area or an area no less than 38m3. If more than 1 gas cylinder containing 1kg of CO2 is present within the same location, the recommended ventilated area should be in proportion to the number of gas cylinders stored in that location. A ventilated area is a non-enclosed area which could include the kitchen, living room etc. See gas bottle and MSDS sheet for complete list of warnings. HydroTap Sparkling Models: BCSS160/125+ and BCSS200/125+ 1. 2. > Turn off the mains water supply and power to the chiller only. Power to the boiler must remain on. Remove the gas bottle from the strap. Make sure the regulator knob is turned fully anti-clockwise to the end-stop before removing. Remove the regulator from the gas bottle turning anti-clockwise. • Screw the regulator onto the new gas bottle. Be aware that some CO2 may be discharged from the connection to the regulator as the bottle and the regulator are assembled together. Any CO2 released will be cold. • Connect the braided gas hose to the regulator, taking care not to lose the plastic olive in the braided hose nut. Turn on the regulator clockwise and adjust to 0.27 MPa (2.7 bar). The arrow should sit in the green section of the regulator gauge; it should not fall in the red or yellow sections. • Using soapy water perform a leak test. Apply the soapy water to the gas connections using a sponge. If any bubbles appear and grow, there is a gas leak at the connection. Clean away the soapy residue and tighten or refit the leaking connection. Make sure the regulator is turned off when tightening or refitting the leaking connection. • Once satisfied that there are no leaks and with the regulator set at 0.27 MPa (2.7 bar), refit the gas bottle to the Velcro strap and secure the bottle. 3. Scroll through the menu on the display until “CO2 purge off” is displayed. Press the Adjust . Water will be dispensed followed by CO2 gas. Allow CO2 to be dispensed for 10 seconds. Then press the Adjust to stop the purge. Then press the Menu to resume normal operation. 4. Turn on water supply and mains power to the chiller. Wait 20 seconds to allow the water in the carbonator can to be refilled. 5. Press both levers simultaneously and check that sparkling water is dispensed. The water may initially spurt out and then normal flow will resume. For more detailed instructions please refer to your products instruction manual. > > CO2 Disposable Gas Bottle Replacement Instructions V1.00 Sept. 2012 HydroTap Sparkling Models: BCS120/125+ and DOMBCS 1. > Remove the gas bottle from the strap. Make sure the regulator knob is turned fully anti-clockwise to the end-stop before removing. Remove the regulator from the gas bottle turning anti-clockwise. • Screw the regulator onto the new gas bottle. Be aware that some CO2 may be discharged from the connection to the regulator as the bottle and the regulator are assembled together. Any CO2 released will be cold. • Connect the braided gas hose to the regulator, taking care not to lose the plastic olive in the braided hose nut. Turn on the regulator clockwise and adjust to 0.27 MPa (2.7 bar). The arrow should sit in the green section of the regulator gauge; it should not fall in the red or yellow sections. • Using soapy water perform a leak test. Apply the soapy water to the gas connections using a sponge. If any bubbles appear and grow, there is a gas leak at the connection. Clean away the soapy residue and tighten or refit the leaking connection. Make sure the regulator is turned off when tightening or refitting the leaking connection. • Once satisfied that there are no leaks and with the regulator set at 0.27 MPa (2.7 bar), refit the gas bottle to the Velcro strap and secure the bottle. 2. Scroll through the menu on the display until “CO2 purge off” is displayed. Press the Adjust . Water will be dispensed followed by CO2 gas. Allow this to continue for approximately 5 seconds. Then press the Adjust to stop the purge. Then press the Menu to resume normal operation. 3. Press both levers simultaneously and check that sparkling water is dispensed. The water may initially spurt out and then normal flow will resume. For more detailed instructions please refer to your products instruction manual. > > ChillTap Sparkling Models: CS125+ and DOMCTS 1. 2. Turn off the water and power supply to the chilled sparkling unit. Remove the gas bottle from the strap. Make sure the regulator knob is turned fully anti-clockwise to the end-stop before removing. Remove the regulator from the gas bottle turning anti-clockwise. • Screw the regulator onto the new gas bottle. Be aware that some CO2 may be discharged from the connection to the regulator as the bottle and the regulator are assembled together. Any CO2 released will be cold. • Connect the braided gas hose to the regulator, taking care not to lose the plastic olive in the braided hose nut. Turn on the regulator clockwise and adjust to 0.27 MPa (2.7 bar). The arrow should sit in the green section of the regulator gauge; it should not fall in the red or yellow sections. • Using soapy water perform a leak test. Apply the soapy water to the gas connections using a sponge. If any bubbles appear and grow, there is a gas leak at the connection. Clean away the soapy residue and tighten or refit the leaking connection. Make sure the regulator is turned off when tightening or refitting the leaking connection. • Once satisfied that there are no leaks and with the regulator set at 0.27 MPa (2.7 bar), refit the gas bottle to the Velcro strap and secure the bottle. 3. Turn the sparkling lever to the on position. Leave it on until all the water has been purged through the tap. Let the tap run for a further 10 seconds to purge the CO2 through the tank. Turn off the sparkling lever. 4. Turn on the cold water supply first and then the power supply. 5. Wait 20 seconds and then turn on the sparkling lever and wait for water to start to come through. 6. Dispense some sparkling water from the tap. For more detailed instructions please refer to your products instruction manual. In order to help preserve our environment we ask that you dispose of this product correctly. Please contact Zip Customer Service for advice on 0845 602 4533. CO2 Cylinder Disposal Steel CO2 cylinders are fully recyclable, to dispose, confirm the cylinder is empty by: • Observing the regulator which should read 0 (zero) bar. • When shaken you will not be able to detect the movement of liquid within the cylinder. Any remaining CO2 should be drained before discarding. Do not dispose of full CO2 cylinder. Do not discharge into any place where accumulation could be dangerous. Discharge to atmosphere in a well ventilated place. Discharge to atmosphere in large quantities should be avoided. To drain cylinder, in a well ventilated area, attach the regulator to the bottle and open the valve until the gas cylinder is empty. Once empty, do not dispose of with general household waste but take to your local recycling centre. Contact Zip Customer Service for advice on 0845 602 4533 if further guidance is required. CO2 Disposable Gas Bottle Replacement Instructions V1.00 Sept. 2012 Head Office Zip Heaters (UK) Ltd 14 Bertie Ward Way Dereham Norfolk NR19 1TE Website: www.zipheaters.co.uk sales@zipheaters.co.uk Telephone: 0845 602 4533 Facsimile: 01362 692 448.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No XMP Toolkit : Adobe XMP Core 5.3-c011 66.145661, 2012/02/06-14:56:27 Create Date : 2012:09:06 10:18:57+01:00 Metadata Date : 2012:09:06 10:18:57+01:00 Modify Date : 2012:09:06 10:18:57+01:00 Creator Tool : Adobe InDesign CS6 (Windows) Instance ID : uuid:b55c2103-3d96-4cea-a0d8-3da5be81f2d2 Original Document ID : xmp.did:1852BA126EE8E111AAAEEEAAE804F9BA Document ID : xmp.id:0E3C97D903F8E111BC45BD1D90F98588 Rendition Class : proof:pdf Derived From Instance ID : xmp.iid:0D3C97D903F8E111BC45BD1D90F98588 Derived From Document ID : xmp.did:1DD3CCD9B4F5E1119E389E1589354381 Derived From Original Document ID: xmp.did:1852BA126EE8E111AAAEEEAAE804F9BA Derived From Rendition Class : default History Action : converted History Parameters : from application/x-indesign to application/pdf History Software Agent : Adobe InDesign CS6 (Windows) History Changed : / History When : 2012:09:06 10:18:57+01:00 Format : application/pdf Producer : Adobe PDF Library 10.0.1 Trapped : False Page Count : 2 Creator : Adobe InDesign CS6 (Windows)EXIF Metadata provided by EXIF.tools