Zoom Telephonics 1093WL Zoom ADSL MODEM / Router w/ Wireless-N User Manual

Download:
Mirror Download [FCC.gov]
Document ID	1555953
Application ID	OijQ6PDEQykpZk3EnfyX/Q==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	39.51kB (493840 bits)
Date Submitted	2011-10-06 00:00:00
Date Available	2011-10-06 00:00:00
Creation Date	2011-09-17 10:21:40
Producing Software	Acrobat Distiller 7.0 (Windows)
Document Lastmod	2011-09-28 13:16:20
Document Title	untitled

X7N
U S E R
M A N U A L
NOTICE
This document contains proprietary information protected
by copyright, and this Manual and all the accompanying
hardware, software, and documentation are copyrighted.
No part of this document may be photocopied or
reproduced by mechanical, electronic, or other means in
any form.
The manufacturer does not warrant that the hardware will
work properly in all environments and applications, and
makes no warranty or representation, either expressed or
implied, with respect to the quality, performance,
merchantability, or fitness for a particular purpose of the
software or documentation. The manufacturer reserves the
right to make changes to the hardware, software, and
documentation without obligation to notify any person or
organization of the revision or change.
All brand and product names are the trademarks of their
respective owners.
© Copyright 2011
All rights reserved.
Contents
Contents ............................................................................3
Overview............................................................................6
Installation Instructions ...................................................7
Package Contents........................................................7
Before You Begin.........................................................8
Installing the X7N ..........................................................10
Installing the X7N on a Windows Computer using the
Install Assistant ..........................................................10
Installing your X7N on a Macintosh or other computer
(does not use Install Assistant) ..................................11
Establishing Communication......................................13
Setting Up a Network .....................................................18
Setting Up Your Wireless Network ...............................21
Connecting a Windows 7 Computer with Built-in
Wireless Capabilities..................................................23
Connecting a Windows Vista Computer with Built-in
Wireless Capabilities..................................................26
Connecting a Windows XP Computer with Built-in
Wireless Capabilities..................................................27
Connecting a Wireless-enabled Computer or Device
(including the iPhone or other cellular phones, the iPod
Touch, etc.) to the X7N .............................................29
Connecting a Computer with a Wireless adapter to the
X7N ............................................................................31
Checking Your Settings .............................................33
Setting Wireless Security ..............................................35
Overview ....................................................................35
Setting Up Security Manually.....................................37
Setting Up Security Using Mixed WPA2 / WPA mode37
Setting Up Security Using WEP.................................39
Online Gaming ................................................................42
Status Monitoring ...........................................................44
Why Monitor Status? .....................................................44
Monitoring ADSL Status ................................................44
Advanced X7N Setup Options.......................................46
Viewing the Advanced Setup Options ...........................47
Changing Your WAN Settings .......................................50
Changing Your LAN Settings ........................................53
Configuring Fixed DHCP Mapping ................................54
Creating a Virtual Server ...............................................55
DMZ ..............................................................................56
Port Triggering...............................................................57
Using IP Filters ..............................................................57
Using MAC Filtering ......................................................58
Setting Up a Time Restrictions......................................59
Setting Up a Static Routing Table .................................60
Adding a DNS Server Name .........................................61
Using the ADSL Settings...............................................62
Enabling or Disabling UPnP ..........................................62
Wireless Options ............................................................64
Wireless MAC Filtering..................................................64
WDS ..............................................................................65
Management and Diagnostics.......................................66
Backing Up Your Configuration .....................................69
Resetting Default Settings.............................................70
Remote Access to Your Modem Configuration Settings71
TR-069 ..........................................................................72
Changing User Names and Passwords ........................72
Diagnostics....................................................................73
Appendix A: Troubleshooting Tips...............................74
Appendix B: ADSL Internet Settings Tables................85
Appendix C: Top and Back Panels ...............................91
Appendix D: TCP/IP Network Settings .........................93
Macintosh TCP/IP Settings ........................................93
Windows TCP/IP Settings..........................................95
Appendix E: Configuring Your Web Browser ..............99
Appendix F: Wireless Channels by Country..............105
Appendix G: Getting Help............................................106
Appendix H: Regulatory Information..........................107
Overview
This User Manual provides instructions for setting up your X7N,
connecting the X7N to wired and wireless computers or other
devices on a network, and securing your network. There are also
instructions for setting up the X7N for gaming.
For most customers, Chapter 1 covers what you need to get
connected to the Internet. Chapter 2 applies if you want to set up a
network. Chapters 3 and 4 help you set up and secure your X7N
wireless network, and Chapter 5 provides what you need for
online gaming.
Chapters 6-9 provide advanced information that is primarily for
System Administrators. These chapters explain how to use
advanced features of the X7N such as adding extra security with
firewall filtering, backing up and restoring the X7N configuration,
updating the X7N firmware, creating a fixed IP address, monitoring
status, and management and diagnostic features of your X7N.
1
Installation Instructions
This chapter covers the basic instructions needed to
install your X7N and connect to the Internet. These
instructions can be used by those with a Windows®,
Macintosh®, or Linux operating system.
If you already installed and connected your X7N (by,
for instance, using the separate Quick Start), you can
skip this chapter and begin with Chapter 2: Setting up
a Network on page 18.
Package Contents
Your package contains the following items:
•
Zoom X7N ADSL modem
•
Ethernet cable
•
Power cube
•
CD
•
One long phone cord
•
A splitter to enable you to use a single ADSL wall jack for
both an Internet connection and for telephone service (certain
countries only). Some splitters ship with a small phone cord
attached to the splitter, others ship with a separate small
phone cord.
The CD contains the installation software, documentation,
warranty, and Customer Support information.
If anything is missing or damaged, please contact Zoom Customer
Support or whoever sold you the modem.
In addition, the package may include:
•
Phone-jack adapter to adapt the phone cord to a particular
phone jack (certain countries only)
•
ADSL line filter(s) (certain models only)
Before You Begin
Before you begin installing the X7N modem using this manual, you
must have the following available to you:
•
ADSL service enabled on your telephone line. To do this, you
need to sign up with an ADSL service provider. Once this
service is enabled, you should have an ADSL-enabled
telephone wall jack to plug the X7N modem into. (Your
service provider may refer to ADSL service as DSL service).
•
If ADSL service was working at your location and you
are replacing an ADSL modem, read this.
It’s important to know whether your ADSL service requires
the modem to have a User Name and Password to access and
browse the Internet. This User Name and Password may be
different from the User Name and Password used to access a
service provider’s email or to log in to the modem’s
Configuration Manager.
If your ADSL service DOES require a User Name and
Password, be sure to write down the ones you’ve been using.
They will be useful when you install your Zoom modem.
If your ADSL service DOES NOT require a User Name and
Password, please be aware that some of these services require
you to disconnect your “old” modem for at least 2 hours
before installing a new modem including your Zoom modem.
•
At least one computer for setting up the X7N. The X7N
supports Macintosh, Linux, and Windows operating systems.
Chapter 1: Installation Instructions
X7N User Manual
You may also want to have these available to you:
•
Any computer or other device that you want to connect
without wires to your network. These must have built-in
wireless capabilities or be equipped with a wireless adapter .
The X7N works with 802.11b, 802.11g, and 802.11n
compatible adapters.
•
Any computer or other device that you want to physically
connect to your X7N ETHERNET port. The X7N has four
ETHERNET ports to which you can connect devices. The
computer or other device must have an Ethernet port to
make these connections.
•
Additional Ethernet cables. If you plan to connect more than
one computer directly to the modem, you will need additional
Ethernet cables to make the connection. The modem
supports up to four direct connections with its four
ETHERNET ports.
Installing the X7N
Important! The X7N should be installed near a phone jack with
ADSL service. Ideally it should be located so that it’s not too far
from any wireless devices that will communicate with the X7N.
Sometimes it’s helpful to set up the X7N at one location, and to
then move it to a location that gives better wireless performance.
Important Safety Measures
ƒ To reduce the risk of fire, use the supplied phone cord.
ƒ Do not use this product near water — for example, in a
wet basement or next to a swimming pool.
¾ Macintosh and Linux users: please go to page 11.
Installing the X7N on a Windows
Computer using the Install
Assistant
1 Turn on the Windows computer that you will use for setup.
This can be any Windows 7, Vista™, XP, 2000, Me or 98
computer with an available Ethernet port.
2 Insert the supplied CD into the CD drive of your computer.
The CD should start automatically.
3 Follow the on-screen prompts for the Install Assistant.
4 If you are prompted to enter your ADSL provider User Name
and Password, remember that these terms are case-sensitive.
Pay careful attention to whether you’re using a capital or small
letter, a zero or the letter O, and so on. Clearly write down
and store the User Name and Password, perhaps on the
bottom of your modem and in a ModemSettings document.
Chapter 1: Installation Instructions
X7N User Manual
Note: Windows 7 users, you may see a message box that says your
software might not have installed correctly. You can safely ignore
this message box.
Now check that your installation worked by opening a Web
browser and connecting to your favorite web site. If you cannot
connect to the Web, please refer to Appendix A:
Troubleshooting Tips.
If you want to connect other computers or other devices to the
X7N, continue with Chapter 2: Setting Up a Network on page
18.
Now continue with the next section: Establishing
Communication.
Installing your X7N on a
Macintosh or other computer
(does not use Install Assistant)
1 Shut down the computer that you want to connect to the X7N.
2 Connect an Ethernet cable into any one of the X7N’s
ETHERNET ports and any of the computer’s or other device’s
Ethernet ports. Then turn on the computer or game station.
One Ethernet LED on your modem’s top panel should turn on.
X7N Back Panel Diagram
ANTENNA
DSL
ETH 4
ETH 3
ETH 2
ETH 1
POWER RESET/WPS ON/OFF ANTENNA
11
3 Connect the supplied phone cord between your modem’s DSL
jack and a phone jack with ADSL service.
Note: If you are using your ADSL modem on the same phone
line where you’re also using other equipment such as telephones
or fax machines, you should put an ADSL filter between each
phone and the wall jack where the phone was connected. This
filter prevents interference between the modem and the phone
or other equipment. Your modem may have come with a filter,
and filters are also available from retailers of phones, modems,
and other electronics. DO NOT put a filter between the X7N
and the wall jack that it is connected to.
Phone
Filter
Wall telephone jack
One form of filter is a splitter. Many X7Ns include a splitter,
typically one with three female jacks. To use this splitter, first
connect one end of the included phone cord into the splitter’s
LINE jack and the other end into a telephone wall jack. Plug the
modem into the splitter’s MODEM jack. If you’d like, plug a
phone, fax, or other telephone device into the PHONE jack.
Note: Some splitters come with a short phone cord instead of a
line jack. If you have one of these splitters, plug the short phone
cord into the telephone wall jack and plug the other cords in as
described above.
4 After a few seconds, your DSL LED will begin blinking, then
become solid. If it does not become solid, please refer to the
Troubleshooting Tips in the User Manual on your CD.
5 Refer to Logging into the Configuration Manager on page
13 and then continue with Step 6.
6 Go to the Configuration Manager’s Basic Setup page. Under
Automatic Configuration, click Start.
Chapter 1: Installation Instructions
X7N User Manual
7 If the X7N finds a PPPoE or PPPoA connection, on the Basic
Setup page enter the User Name and Password for your
Internet Service Provider, then click Save. (You should have a
User ID or User Name, which is often your email address or
the characters preceding the @ sign in your email address. You
should also have a password. The PPPoE or PPPoA User
Name and Password are NOT the User ID and Password that
you used to get into the Basic Setup menu.)
Now check that your installation worked by opening a Web
browser and connecting to your favorite web site. If you cannot
connect to the Web, please refer to Appendix A:
Troubleshooting Tips.
If you want to connect other computers or other devices to the
X7N, continue with Chapter 2: Setting Up a Network on page
18.
Now continue with the next section: Establishing
Communication.
Establishing Communication
Important!
Macintosh and Linux users must make sure that the computer’s
TCP/IP settings are configured properly BEFORE starting this
section. See Macintosh TCP/IP Settings on page 93 for
instructions.
You must set up the X7N so that it can communicate with your
Internet service provider. To do this, you use the Zoom
Configuration Manager.
1 Log into the Zoom Configuration Manager:
13
a
Open your Web browser and, in its address bar, type
http://192.168.1.1 and then press the Enter key on your
keyboard.
In the Enter Network Password dialog box, type the
following user name and password in lowercase, then click
OK. (The X7N User Name and Password you enter here
are not the same as the User Name and Password that
your Internet service provider may have given you.)
User Name: admin
Password: zoomadsl
If you are not prompted for a User Name and Password,
do the following in this order: Recheck all connections;
restart the modem and computer; and reset the modem by
pressing the RESET button on the modem’s back panel
for 5 seconds.
Important:
For security, you may want to choose your own X7N password
after the setup is complete. See Changing User Names and
Passwords on page 66.
2 After you log in, use the Basic Setup page to configure the
modem so it can connect with your Internet service provider.
•
To use Automatic Configuration (recommended):
a Under Automatic Configuration, click Start.
b In the "Settings successfully detected" message box,
click OK to return to the Basic Setup page.
c If the X7N finds a PPPoE or PPPoA connection, on
the Basic Setup page enter the user name and
password given to you by your Internet Service
Provider. (Your provider should have given you a
User ID or User Name, usually your email address
or the characters preceding the @ sign in your email
address, and a Password. These are NOT the User
ID and Password that you used to get into the Basic
Setup menu.)
Chapter 1: Installation Instructions
X7N User Manual
If the X7N finds a 1483 Bridged or 1483 Routed
connection, you have the option of using either
dynamic or static IP addressing. Depending on your
situation, select the appropriate option button:
−
−
•
[MOST USERS] Ensure that Obtain an IP
address Automatically is selected if you are
using Dynamic Host Configuration Protocol (also
known as DHCP or dynamic IP addressing). This
option is selected by default because most Internet
service providers use DHCP.
Select Use the following IP Address only if you
are using a static IP address. (You should know if
you are using static IP addressing. There is
typically an extra charge for a static IP address and
you usually have to make special arrangements
with your Internet service provider to get one.)
Then enter the IP Address, Subnet Mask,
Default Gateway, and DNS that you plan to use.
Click Save/Reboot. Continue with step 3 to test
your network.
To configure your settings manually if Automatic Configuration does
not work, follow these instructions:
a On the Basic Setup page, enter your Protocol,
Encapsulation, VPI, and VCI settings in the
appropriate boxes. Your service provider should
supply these values. If you do not know these settings,
refer to the tables starting on page 73.
b NAT (Network Address Translation) is Enabled by
default. This feature lets multiple users access the
Internet sharing a single IP address. Enabled is
typically the right setting. Select Disable in the
unlikely event that you want to assign different public
IP addresses to each network user.
c Depending on the Protocol setting you selected the
bottom half of the page will change so that you can
enter additional information.
ƒ If you selected PPPoA or PPPoE, enter your
ADSL User Name and Password in the
appropriate boxes. Your Internet service provider
should have given this information to you. (Your
15
User Name is typically your email address or the
characters preceding the @ sign in your email
address. This is NOT the same User Name and
Password that you used earlier to open the Zoom
Configuration Manager.)
ƒ
If you selected 1483 Bridged or 1483 Routed,
you have the option of using either dynamic or
static IP addressing. Depending on your situation,
select the appropriate option button:
−
[MOST USERS] Ensure that Obtain an IP
address Automatically is selected if you are
using Dynamic Host Configuration Protocol
(also known as DHCP or dynamic IP
addressing). This option is selected by default
because most Internet service providers use
DHCP.
−
Select Use the following IP Address only if
you are using a static IP address. (You should
know if you are using static IP addressing.
There is typically an extra charge for a static
IP address and you usually have to make
special arrangements with your Internet
service provider to get one.)
Then enter the IP Address, Subnet Mask,
Default Gateway, and DNS that you plan to
use. Click Save/Reboot.
3 Verify that you Internet connection is working. Open your
Web browser (for instance, Internet Explorer, Firefox, or
Chrome) and try to connect to a familiar Web address. If you
connect successfully, you are ready to set up the rest of your
network.
(If you do not connect, see Appendix A: Troubleshooting Tips
on page 73.)
Chapter 1: Installation Instructions
X7N User Manual
Tip!
If you configured the X7N using a notebook computer, you can
keep it plugged in or you can disconnect it from the unit’s
ETHERNET port. As long as the X7N remains plugged into an
ADSL wall jack and a power source, the X7N can function as a
stand-alone device. You can then make the notebook part of your
wireless network.
Congratulations! You have established communication and your
computer is connected to the Internet.
If you wish to add additional devices to your X7N, continue with
Chapter 2: Setting Up a Network on page 18.
If you do not wish to add additional devices to your X7N, you are
ready to start using your X7N. If you want additional information
on how to use your X7N, you may choose to continue with:
¾ Chapter 5 to learn about using the X7N with
online gaming.
¾ Chapter 6 to learn about monitoring your ADSL
Status. (Most users will not need to use status
monitoring.)
¾ Chapter 7 to learn about the advanced features of
the X7N. (Most users will not need to change
advanced features.)
17
2
Setting Up a Network
Once a computer that is directly connected to the X7N modem is
able to browse the Internet, you know for certain that your ADSL
Internet connection is working. Now you can set up the rest of
your network.
It is up to you whether you want to have some computers
connected directly to the X7N and others connected wirelessly.
The X7N supports both wired and wireless connections. You can
have up to 253 connections, four of which can be wired directly
through the X7N’s four ETHERNET ports. You can also plug a
network device (such as a hub, switch, router, or Homeplug
adapter) into one of the ETHERNET ports.
To set up your network, you can do any or all of the following, in
any order that you choose:
•
If you want to connect additional computers directly to the
X7N, see To Connect Additional Wired Computers below.
•
If you want to connect a hub, switch, router or other device
directly to the X7N, see To Connect a Network Device on
page 19.
•
If you want to connect additional computers or other devices
using a wireless network, see Chapter 3: Setting Up Your
Wireless Network on page 21.
Chapter 2: Setting Up a Network
X7N User Manual
To Connect Additional Wired
Computers
You can connect up to four computers that have Ethernet ports
directly to the X7N.
1 Shut down and power of the computer you want to connect to
the X7N. (This is important because the computer must locate
the correct IP address for the modem. This is done when the
computer is turned back on in step 3 below.)
2 Plug one end of an Ethernet cable into one of the modem’s
ETHERNET ports and plug the other end into the computer’s
Ethernet port.
3 Turn on the computer.
4 Verify that your Internet connection is working. Open your
Web browser (for instance, Internet Explorer, Firefox, or
Chrome) and try to connect to a familiar Web address.
5 Repeat steps 1–4 for each computer you want to add.
To Connect a Network Device
You can use one of the ETHERNET ports on the X7N to plug
in a network device (for example, a hub, switch, router, or
Homeplug adapter).
1 Plug one end of an Ethernet cable into one of the modem’s
ETHERNET ports and the other end into the network
device’s Ethernet port. (For a hub or a switch, this is typically
called an Uplink or Expansion port. For a router, this is
typically called a WAN port.)
2 Set up your network and/or device. Refer to the
documentation provided with your particular network device
for instructions on how to do this.
3 Once your network and/or device is set up, reboot any
computer that is part of the network.
4 Verify that your Internet connection is working. Open the
Web browser (for instance, Internet Explorer, Firefox, or
19
Chrome) on each computer and try to connect to a familiar
Web address.
Congratulations! You have set up your wired devices. If you
have wireless devices that you want to add to your network, go to
Setting Up Your Wireless Network on page 21.
Chapter 2: Setting Up a Network
X7N User Manual
3
Setting Up Your Wireless
Network
This chapter discusses how to set up a wireless
network using computers and/or other devices that
have built-in wireless capabilities and/or a wireless
adapter. Chapter 4 provides information about
implementing wireless security.
Note that for each computer or other device added to your
wireless network, you will need to take appropriate steps for setting
up that computer or other device. To do that, select one of the
possibilities for that computer or other device below:
¾ If all the wireless devices you plan to connect to your network
support push button Wi-Fi Protected Setup (WPS), you can
use WPS to connect and secure your devices in one step.
Follow the instructions below. If your devices only support
using a PIN code, then you must configure security manually.
Refer to Setting Up Security Manually on page 37.
If all the wireless devices you plan to connect to your network
do not support WPS, skip this bullet point and continue with
the next bullet point.
Note: WPS configures one client device at a time. Please
repeat the configuration method for each client on your
wireless network that supports WPS security.
Chapter 3: Setting Up Your Wireless Network
21
The X7N supports Push Button WPS configuration. This
button can be either a physical button on the unit or a
software button in its application.
Press the WPS button on your Router and hold it in for
seven (7) seconds until the Wireless LED starts blinking
rapidly.
Important! The Registrar (the device configuring the
WLAN,) goes into the WPS mode and the Enrollee (the
device joining the WLAN) then looks for it. You should
always start the Registrar first. The X7N is configured as
a Registrar so you should put it into WPS mode first..
Click or press the WPS button on the client device. This
button may be a physical button on the unit or a software
button in its application.
Refer to your client device's documentation for further
instructions, if necessary.
Open your Web browser (for instance, Internet Explorer,
Firefox, or Chrome) and try to connect to a familiar Web
address.
If you connect successfully, you are ready to browse the Web!
If it fails to connect, refer to Appendix A:
Troubleshooting Tips on page 73.
If you want additional information on how to use your
X7N, you may choose to continue with:
Chapter 5 to learn about using the X7N
with online gaming.
Chapter 6 to learn about monitoring your
ADSL Status. (Most users will not need
to use status monitoring.)
Chapter 7 to learn about the advanced
features of the X7N.(Most users will not
need to change advanced features.)
Chapter 3: Setting up Your Wireless Network
X7N User Manual
¾ Many newer Windows 7, Vista, and XP computers have
built-in wireless networking capabilities and do not require
the installation of a wireless component. If this is the case, you
should set up that computer’s wireless connection using the
Windows 7, Vista, or XP connect utility. See the sections
below on connecting Windows 7 (page 23) , Vista (page 23),
or XP (page 27) computers with built-in wireless capabilities.
¾ Some computers may have built-in wireless networking
capabilities, but do not use the Windows 7, Vista, or XP utility to
configure their device. If this is so, set up your computer’s wireless
connection using the instructions on page 28 for Connecting a
Wireless-enabled Computer or Device to the X7N.
¾ If you have a non-computer wireless device like an iPhone or
other cellular phone, iPod Touch, etc., see the instructions on
page 28 for Connecting a Wireless-enabled Computer or
Device to the X7N.
¾ Some computers may need a wireless network adapter installed.
This can be a USB adapter, PC Card adapter, or PCI adapter. When
you install the adapter, make sure that it is set to infrastructure or
access point mode (NOT ad-hoc or peer-to-peer mode). If you
need help installing your wireless adapter or setting its mode, refer
to the documentation that came with it. After you install the adapter,
see the instructions on page 28 for Connecting a Computer with
a wireless adapter to the X7N.
Connecting a Windows 7
Computer with Built-in Wireless
Capabilities
From the taskbar, click on the wireless symbol.
Chapter 3: Setting Up Your Wireless Network
23
2
In the wireless network options box, highlight Zoom and click
Connect.
• If your desired network is secured, in the next dialog box
enter the security key or password and click Connect.
• If your desired network is unsecured, in the message box
select Connect Anyway.
Note: We strongly recommend that you set up a secured
network. For information on wireless security, see Setting
Wireless Security on page 35.
¾ When you click on the wireless network option box,
Windows will scan for available networks. More than one
wireless network may appear in the list. These are other
wireless networks that are within range of your network.
Your neighbors, for instance, may be within range of your
network. Each wireless network has a channel associated
with it. We recommend there be at least a five-channel
difference between your network and those of your
neighbors. Having less than a five-channel difference may
result in interference with your connection. By default, the
X7N uses channel 10. If you need to change this channel,
you must do so using the Wireless Setup page of the
Zoom Configuration Manager. For instructions on how
to log in to the Zoom Configuration Manager, see page
13. After logging in, select Wireless from the left-hand
Chapter 3: Setting up Your Wireless Network
X7N User Manual
menu. On the Wireless page you can select a new channel
from the drop-down menu.
If you have difficulty connecting, make sure you have entered
the correct password (if security is enabled). Otherwise refer to
Appendix A: Troubleshooting Tips on page 73.
In the Successfully connected to [desired network] dialog
box, you have three options. You can:
•
Select Save the network and Start this connection
automatically if you always want to connect to the same
network. Then click Close. The next time you start your
computer you will automatically connect to the selected
network.
• Select Save the network and clear the Start this
connection automatically check box if you don't want to
automatically connect to this network every time you start
your computer but you will want to connect in the future.
Click Close to display the Select a location . . . dialog box
where you choose a location. Windows 7 automatically
applies the correct network security settings.
If the User Account Control dialog box appears, click
Continue.
• Click Close to complete the connection procedure. Select
this option if you are connecting to this network only one
time.
To disconnect from the current network:
Right-click the wireless network icon in the notification area of
the Windows taskbar.
Right-click Zoom and select Disconnect.
Chapter 3: Setting Up Your Wireless Network
25
Connecting a Windows Vista
Computer with Built-in Wireless
Capabilities
From the Start menu select Connect to.
In the Connect to a network dialog box, highlight Zoom and
click Connect.
• If your desired network is secured, in the next dialog box
enter the security key or password and click Connect.
• If your desired network is unsecured, in the message box
select Connect Anyway.
Note: We strongly recommend that you set up a secured
network. For information on wireless security, see Setting
Wireless Security on page 35.
¾ When you click on the wireless network option box,
Windows will scan for available networks. More than one
wireless network may appear in the list. These are other
wireless networks that are within range of your network.
Your neighbors, for instance, may be within range of your
network. Each wireless network has a channel associated
with it. We recommend there be at least a five-channel
difference between your network and those of your
neighbors. Having less than a five-channel difference may
result in interference with your connection. By default, the
X7N uses channel 10. If you need to change this channel,
you must do so using the Wireless Setup page of the
Zoom Configuration Manager. For instructions on how
to log in to the Zoom Configuration Manager, see page
13. After logging in, select Wireless from the left-hand
menu. On the Wireless page you can select a new channel
from the drop-down menu.
If you have difficulty connecting, make sure you have entered
the correct password (if security is enabled). otherwise refer to
Appendix A: Troubleshooting Tips on page 73.
Chapter 3: Setting up Your Wireless Network
X7N User Manual
3
In the Successfully connected to [desired network] dialog
box, you have three options. You can:
•
Select Save the network and Start this connection
automatically if you always want to connect to the same
network. Then click Close. The next time you start your
computer you will automatically connect to the selected
network.
• Select Save the network and clear the Start this
connection automatically check box if you don't want to
automatically connect to this network every time you start
your computer but you will want to connect in the future.
Click Close to display the Select a location . . . dialog box
where you choose a location. Windows Vista automatically
applies the correct network security settings.
If the User Account Control dialog box appears, click
Continue.
• Click Close to complete the connection procedure. Select
this option if you are connecting to this network only one
time.
To disconnect from the current network:
From the Start menu, select Connect to.
In the Disconnect or Connect to another network dialog
box, select the current network and click Disconnect.
In the Are You Sure? message box, click Disconnect again.
In the next dialog box, you can connect to another network or
click Close to complete the disconnect procedure.
Connecting a Windows XP
Computer with Built-in Wireless
Capabilities
On your Windows desktop, click the Start button then click
SettingsÆControl Panel.
Double-click the Network Connections icon.
Chapter 3: Setting Up Your Wireless Network
27
3
Right-click the Wireless Network Connection icon, then
select Properties.
On the Wireless Network Connection Properties dialog
box, select the Wireless Networks tab. Windows will
automatically scan for available wireless networks in your area.
Any compatible networks within range will appear in the
Available networks list. It should find the wireless network of
the X7N—named Zoom. (The scan is done automatically
because the Use Windows to configure my wireless
network settings check box is selected by default).
Select Zoom from the Available networks list, then click the
Configure button to add it to the Preferred networks list.
The notebook will try to connect to the Internet using the
wireless networks listed here, in the order in which they appear.
(If you already have networks listed here, we recommend you
either remove them or use the Move up button to move
Zoom to the top of the list.)
Click OK.
Test your wireless connection. From the computer or
notebook that you set up, open your Web browser (for
instance, Internet Explorer or Firefox) and try to connect to a
familiar Web address.
If you connect successfully, your notebook’s wireless
capability is configured and you are ready to browse the Web!
Important!
If you want to add security to your network, please see Setting
Wireless Security on page 35.
¾ When you click on the wireless network option box,
Windows will scan for available networks. More than one
wireless network may appear in the list. These are other
wireless networks that are within range of your network.
Your neighbors, for instance, may be within range of your
network. Each wireless network has a channel associated
with it. We recommend there be at least a five-channel
difference between your network and those of your
neighbors. Having less than a five-channel difference may
result in interference with your connection. By default, the
X7N uses channel 10. If you need to change this channel,
you must do so using the Wireless Setup page of the
Chapter 3: Setting up Your Wireless Network
X7N User Manual
Zoom Configuration Manager. For instructions on how
to log in to the Zoom Configuration Manager, see page
13. After logging in, select Wireless from the left-hand
menu. On the Wireless page you can select a new channel
from the drop-down menu.
To disconnect from the current network:
On your Windows desktop, click the Start button then click
SettingsÆControl Panel.
Double-click the Network Connections icon.
Right-click the Wireless Network Connection icon, then
select View Available Wireless Networks and click Zoom.
Click Disconnect in the wireless connection window.
Close the window by clicking on the X at the top of the
window.
Connecting a Wireless-enabled
Computer or Device
(including the
iPhone or other cellular phones, the iPod
Touch, etc.)
to the X7N
Go to the wireless-enabled computer or device that you want
to add to the network. The device should have software that
will let it perform a site search to scan for available wireless
networks in your area. You may have to click on something
like Settings and then Wi-Fi. When the SSID (Service Set
Identifier) of your X7N wireless network appears in the list—
the default SSID is Zoom—select it as the network you want
to use to connect to the Internet.
Tip!
If you need help, refer to the documentation that came with
your wireless device.
Chapter 3: Setting Up Your Wireless Network
29
There are several site scan issues you should be aware of:
¾ More than one wireless network may appear in the list.
These are other wireless networks that are within range of
your network. Your neighbors, for instance, may be within
range of your network. Each wireless network has a
channel associated with it. We recommend there be at least
a five-channel difference between your network and those
of your neighbors. Having less than a five-channel
difference may result in interference with your connection.
By default, the X7N uses channel 10. If you need to change
this channel, you must do so using the Wireless Setup
page of the Zoom Configuration Manager. For
instructions on how to log in to the Zoom Configuration
Manager, see page 13. After logging in, select Wireless
from the left-hand menu. On the Wireless page you can
select a new channel from the drop-down menu.
¾ If you want to secure your wireless network so it won’t be
accessible by others, you should specify security settings.
To learn how, see Setting Wireless Security on page 35.
(By default, the wireless connections provided by the X7N
do not have any security applied.)
Test your wireless connections. From each computer or device
that you set up, open your Web browser (for instance, Internet
Explorer, Firefox, or Chrome) and try to connect to a familiar
Web address.
If you connect successfully, you are ready to browse the Web!
Important!
To add security to your network, see Setting Wireless Security on
page 35.
To disconnect from the current network:
On your wireless device or computer, find the wireless
network connection option (similar to the process of adding
your device or computer to the network).
Click or highlight Zoom.
Select or click on Disconnect or similarly-named button.
Chapter 3: Setting up Your Wireless Network
X7N User Manual
Connecting a Computer with a
Wireless adapter to the X7N
Go to the computer that is set up with a wireless adapter that
you want to add to the network. The computer should have
software that will let it perform a site search to scan for
available wireless networks in your area. When the SSID
(Service Set Identifier) of your X7N wireless network appears
in the list—the SSID is Zoom—select it as the network you
want to use to connect to the Internet.
Tip!
For most wireless adapters, you will use its wireless
configuration manager software and click a Scan button or
select a Site Scan, Scan Networks, or other similarly named
tab to do a site search. If you need help, refer to the
documentation that came with your wireless adapter.
There are several site scan issues you should be aware of:
¾ If you are trying to connect to a wireless network that
already has security enabled, your wireless adapter might
not recognize what type of security is on the network.
You may need to manually set up the security for your
adapter. If you need help, refer to the documentation that
came with your wireless adapter.
¾ Windows 7, XP, and Vista users: If you installed a
wireless adapter on a Windows 7, XP, or Vista computer,
Windows may try to automatically configure the adapter
(rather than let you use the software provided with the
wireless adapter). You will know this is happening because
you will be prompted with a message about one or more
wireless networks being available. You will also be able to
click a link to open the Wireless Network Connection
Properties dialog box. If this happens, click the link, clear
the Use Windows to configure my wireless network
settings check box, and then click OK. You can then use
Chapter 3: Setting Up Your Wireless Network
31
the software provided with your wireless adapter without
interruption from Windows.
¾ More than one wireless network may appear in the list.
These are other wireless networks that are within range of
your network. Your neighbors, for instance, may be within
range of your network. Each wireless network has a
channel associated with it. We recommend there be at least
a five-channel difference between your network and those
of your neighbors. Having less than a five-channel
difference may result in interference with your connection.
By default, the X7N uses channel 10. If you need to change
this channel, you must do so using the Wireless Setup
page of the Zoom Configuration Manager. For
instructions on how to log in to the Zoom Configuration
Manager, see page 13. After logging in, select Wireless
from the left-hand menu. On the Wireless page you can
select a new channel from the drop-down menu.
¾ If you want to secure your wireless network so it won’t be
accessible by others, you should specify security settings.
To learn how, see Setting Wireless Security on page 35.
(By default, the wireless connections provided by the X7N
do not have any security applied.)
Test your wireless connections. From each desktop or
notebook computer that you set up, open your Web browser
(for instance, Internet Explorer or Firefox) and try to connect
to a familiar Web address.
If you connect successfully, you are ready to browse the Web!
Important!
To add security to your network, see Setting Wireless Security on
page 35.
To disconnect from the current network:
On your computer that has a wireless adapter, find the wireless
network connection option (similar to the process of adding
your computer to the network).
Click or highlight Zoom.
Select or click on Disconnect or similarly-named button.
Chapter 3: Setting up Your Wireless Network
X7N User Manual
Checking Your Settings
If you ever need to check your wireless settings, you can do so
from the Wireless Setup page. This page is available in the Zoom
Configuration Manager by clicking Wireless from the left-side
menu. For instructions on how to log in to the Zoom
Configuration Manager, go to page 13.
The table below explains the Wireless Basic settings:
This setting…
Lets you specify…
Enable Wireless
A check mark in the Enable Wireless check
box shows that your wireless network is up. If
there is no check mark next to the Enable
Wireless check box, this indicates your
Wireless is not enabled.
Channel
Indicates the channel your wireless connection
uses by default for your wireless connection.
The X7N comes set for channel 10.
SSID (Wireless
Network
Name)
The Service Set Identifier for your wireless
network. By default, the SSID for the X7N is
Zoom. You can change the SSID to any name
that you want.
BSSID
(Broadcast
SSID)
Shows the MAC address.
Country
Select your country from the drop-down
menu.
Hide SSID
Click in the check box if you do not want to
broadcast the SSID of your network.
Chapter 3: Setting Up Your Wireless Network
33
Other Wireless Settings
Max Clients: up to 16 allowed.
Clients Isolation: Which ever wireless clients connect to an SSID
with "Client Isolation" enabled will be isolated from themselves.
They will still be able to communicate successfully with any clients
connected to different SSIDs.
Wireless – Guest/Virtual Access Points: Allows you to connect
up to 3 virtual access points. Click the Enabled box to activate each
virtual access point.
Chapter 3: Setting up Your Wireless Network
X7N User Manual
4
Setting Wireless Security
When you first set up your X7N wireless network, security is
turned off by default. This means that your wireless signal is
not encrypted and that anyone with compatible wireless
technology can access your computer network and the
Internet using your wireless connection. This chapter
explains how to set up wireless security to protect your
network and Internet connection.
Overview
Before setting up wireless security you need to decide which
method to use.
•
Use Wi-Fi Protected Setup (WPS) if all of your devices
support WPS security. WPS is easy to configure. Please
refer to WPS Configuration below for details.
•
If not all your devices support WPS or you plan on using
WEP security because you are using an older device that
only supports WEP than refer to Setting Up Security
Manually on page 37.
WPS Configuration
You can automatically configure WPS security using the router's
built-in WPS configuration program on each client device that is
part of your wireless network. The X7N supports Push Button
WPS configuration. This button can be either a physical button on
35
the unit or a software button in its application. If your devices only
support using a PIN code, then you must configure security
manually. Refer to Setting Up Security Manually on page 37.
Note: WPS configures one client device at a time. Please repeat the
configuration method for each client on your wireless network that
supports WPS security.
Press the WPS button on your Router and hold it in for seven
(7) seconds until the Wireless LED starts blinking rapidly.
Important! The Registrar (the device configuring the
WLAN,) goes into the WPS mode and the Enrollee (the
device joining the WLAN) then looks for it. You should always
start the Registrar first. The X7N is configured as a Registrar
so you should put it into WPS mode first..
Click or press the WPS button on the client device. This
button may be a physical button on the unit or a software
button in its application.
3 Refer to your client device's documentation for further
instructions, if necessary.
Open your Web browser (for instance, Internet Explorer, Firefox,
or Chrome) and try to connect to a familiar Web address.
If you connect successfully, you are ready to browse the Web!
If it fails to connect, refer to Appendix A: Troubleshooting Tips
on page 73.
If you want additional information on how to use your X7N, you
may choose to continue with:
¾ Chapter 5 to learn about using the X7N with
online gaming.
¾ Chapter 6 to learn about monitoring your ADSL
Status. (Most users will not need to use status
monitoring.)
Chapter 4:Setting Wireless Security
X7N User Manual
¾ Chapter 7 to learn about the advanced features of
the X7N.(Most users will not need to change
advanced features.)
Setting Up Security Manually
To manually set up wireless security, you will create and enter a
unique passphrase or an alphanumeric key. Once entered, only
devices with the proper key or passphrase will be allowed to
establish a connection to the network.
There are two basic ways to configure and implement a passphrase
or key. They are WPA2/WPA and WEP. The X7N supports
WPA2/WPA mixed mode which lets you connect with devices
that support either standard. We recommend you use this setting
unless you know that you have a device that only supports WEP.
You can check to see if all other clients that you plan to put on the
network support WPA2 or WPA. You can do this by checking the
manual that came with each device or by checking the
configuration software for the installed device. Look under
Security or Encryption or Setup or Advanced Features. If all
the clients support WPA2 or WPA, proceed with Setting Up
Security Using WPA2/WPA. If they do not, skip to Setting Up
Security Using WEP on page 39.
Setting Up Security Using Mixed
WPA2 / WPA mode
WPA2 and WPA use a passphrase that you choose and enter on
the X7N and other wireless devices on the network (clients) to set
up security. To use Mixed WPA2 /WPA, all of the wireless devices
on your network must support either encryption method. If you
37
know that all your devices support the more secure WPA2 you can
select WPA2 instead of mixed WPA2/WPA.
Check to see that all other clients that you plan to put on the
network support WPA2 or WPA. If they do not, skip to
Setting Up Security Using WEP on page 39.
2 Open the Zoom Configuration Manager by typing the following
in your Web browser's address bar: http://192.168.1.1
3 In the Enter Network Password dialog box, type the
following User Name and Password in lower case, then click
OK..
User Name: admin
Password: zoomadsl
(The User Name and Password entered here are not the same as
the user name and password that your Internet service provider
may have given you.)
4 Click Wireless on the left-side menu of the Configuration
Manager.
Then click Security on the left-side menu and from the dropdown menu for Select SSID, select Zoom.
From the Network Authentication drop-down menu, select
Mixed WPA2 / WPA.
In the WPA Pre-Shared Key text box, enter a passphrase of
your choice.
Write down this passphrase and put it where you can find it –
on the bottom of the X7N case, for instance.
Click Save/Apply.
10 Now you need to set up each of your wireless devices with the
SSID and passphrase.
First, make sure that the device's wireless
capability is switched on. (Many notebooks have a
switch for wireless, for instance.)
Next go to the device’s area for configuring a
wireless network connection.
For a Windows computer, click the Wireless
Networking icon at the lower right corner of the
screen.
Chapter 4:Setting Wireless Security
X7N User Manual
c
Select the Site Survey or Scan option to see a list
of the access points in your area. That list should
include the SSID Zoom.
Select Zoom and enter the WPA2 key that you
just wrote down in Step 8.
Note: If you are not using the Windows configuration
utility, you may need to manually set WPA2 security
on your device. Refer to the documentation that came
with your device.
Save your settings.
That’s it! Your security setup is now complete!
Open your Web browser (for instance, Internet Explorer, Firefox,
or Chrome) and try to connect to a familiar Web address.
If you connect successfully, you are ready to browse the Web!
If it fails to connect, refer to Appendix A: Troubleshooting Tips
on page 73.
If you want additional information on how to use your X7N, you
may choose to continue with:
¾ Chapter 5 to learn about using the X7N with
online gaming.
¾ Chapter 6 to learn about monitoring your ADSL
Status. (Most users will not need to use status
monitoring.)
¾ Chapter 7 to learn about the advanced features of
the X7N.(Most users will not need to change
advanced features.)
Setting Up Security Using WEP
If all of your network devices DO NOT support WPA2 or WPA,
39
you can use WEP to configure network security. WEP can be
configured two ways: 64-bit and 128-bit. 128-bit WEP provides a
bit more security than 64-bit, but 128-bit WEP also tends to
diminish network performance. We recommend that most people
configure their WEP for 64-bit security.
Open the Zoom Configuration Manager by typing the following
in your Web browser's address bar: http://192.168.1.1
2 In the Enter Network Password dialog box, type the
following User Name and Password in lower case, then click
OK..
User Name: admin
Password: zoomadsl
(The User Name and Password entered here are not the same as
the user name and password that your Internet service provider
may have given you.)
3 Click Wireless on the left-side menu of the Configuration
Manager.
Then click Security on the left-side menu and from the dropdown menu for Select SSID, select Zoom.
From the Network Authentication drop-down menu, select
WEP Open or WEP Shared. (Most devices use WEP Open;
however some older Apple Macbooks require WEP Shared.)
For Encryption Strength select 128-bit or 64-bit. (The 128-bit
option is more secure but 64-bit may be faster on older devices.
We recommend setting 64-bit security.)
In the Network Key text box, enter a passphrase of your
choice.
Write down this passphrase and put it where you can find it –
on the bottom of the X7N case, for instance.
Click Save/Apply.
10 Now you need to set up each of your wireless devices with the
SSID and passphrase.
First, make sure that the device's wireless
capability is switched on. (Many notebooks have a
switch for wireless, for instance.)
Chapter 4:Setting Wireless Security
X7N User Manual
b
Next go to the device’s area for configuring a
wireless network connection.
For a Windows computer, click the Wireless
Networking icon at the lower right corner of the
screen.
Select the Site Survey or Scan option to see a list
of the access points in your area. That list should
include the SSID Zoom.
Select Zoom and enter the WEP key that you just
wrote down in Step 8.
Note: If you are not using the Windows configuration
utility you may need to manually set WEP security on
your device. Refer to the documentation that came
with your device.
Save your settings.
That’s it! Your security setup is now complete!
Open your Web browser (for instance, Internet Explorer, Firefox,
or Chrome) and try to connect to a familiar Web address.
If you connect successfully, you are ready to browse the Web!
If it fails to connect, refer to Appendix A: Troubleshooting Tips
on page 73.
If you want additional information on how to use your X7N, you
may choose to continue with:
¾ Chapter 5 to learn about using the X7N with
online gaming.
¾ Chapter 6 to learn about monitoring your ADSL
Status. (Most users will not need to use status
monitoring.)
¾ Chapter 7 to learn about the advanced features of
the X7N.(Most users will not need to change
advanced features.)
41
5
Online Gaming
If you are using your router for gaming, you may need to make
changes to the router’s firewall setting for the game to work. This
is done by setting up a DMZ or virtual server, or using port
triggering so that the modem’s firewall won’t block the other
players from your system during your gaming. The main difference
between the three methods is the amount of access someone has to
your system.
A virtual server will allow access to your computer or gaming
station on certain ports. A port is a channel that is used by
applications (such as games) for communication. For example, the
directions for the game you want to play over the Internet might
tell you to open up port 6000.
Port triggering works by sensing when data is sent out on the
predetermined outgoing port and then automatically opening up
the corresponding incoming port(s). It will automatically forward
the traffic on the incoming port to the computer that accessed the
outgoing port. If your game uses one port to send outgoing data
and a different port (or ports) for incoming data, you may want to
use port triggering. The advantage of port triggering is that it is
more secure than setting up a virtual server since the incoming port
is only open when you are using it, and since it tracks which
computer sent the outgoing data. Port triggering can also be easier
to set up because you do not need to know the IP address of your
gaming station. The disadvantage of port triggering is that only 1
host can be accessing the port at one time, so if you have two
computers or game stations playing the same game on your
network you will need to use a virtual server or DMZ.
A DMZ differs from a virtual server in that it allows access on all
Chapter 5: Online Gaming
X7N User Manual
ports of the computer. Because of this, DMZ's are less secure and
should be used with caution on your computer. However DMZ’s
work well with your gaming stations since security is not as much
of an issue for gaming stations as it is for computers.
Once you’ve decided what type of security to use for gaming, you
can set up that security using the appropriate section of this manual:
•
Virtual Server: For instructions on how to set up a virtual
server, please refer to page 54.
•
DMZ: For instructions on how to set up a DMZ, please
refer to page 56.
•
Port Triggering: For instructions on how to set up port
triggering, please refer to page 57.
43
6
Status Monitoring
This chapter discusses how to check the status of your
modem and its ADSL connection.
Most users can skip this chapter, as it is primarily for
advanced users and for those who are instructed by
their Internet service provider or Zoom Technical
Support to verify settings, usually for troubleshooting.
If you skip this section, you should go to Chapter 7.
Why Monitor Status?
The X7N provides easy-to-read screens for you to review the status
of the modem and its ADSL connection.
While most users will probably never need to check the status,
there are some cases in which it would be helpful. For example,
you may need to know the IP address assigned to you by your
Internet service provider.
For advanced users with special configuration needs, the status
information is useful for overall system maintenance.
Monitoring ADSL Status
If you want to check the status of your ADSL connection, click on
the Status link on the left pane in the Zoom Configuration
Chapter 6: Status Monitoring
X7N User Manual
Manager. (If you forgot how to log in to the Zoom
Configuration Manager, see page 13.)
The Status page provides information about your ADSL
connection. For example, you can verify whether your ADSL
connection is active or not. You can also monitor related ADSL
parameters—for example, how fast the X7N is transferring data
(Downstream Speed and Upstream Speed), your WAN settings,
your LAN settings, and so forth.
Note:
The Status page does not provide a way to change any of these
settings—see Chapter 7: Advanced Setup Options, if you need
to make changes to these settings.
45
7
Advanced X7N Setup Options
Advanced Setup is primarily for technically advanced
users. For most people, the options that are set by
default when the X7N is installed are sufficient.
However, those who want or need to change the X7N
settings can do so using the Advanced Setup page in
the Zoom Configuration Manager. This chapter
explains the advanced options and features of the
X7N modem and how to apply them to your network.
The information in this chapter applies to you if:
•
Your Internet service provider instructs you to
enable, disable, or change the default settings for
your X7N
•
You need to change your Wide Area Network
settings
•
You want to change the default firewall settings to
block particular IP addresses and intrusive hosts
•
You want to change your ADSL password
•
You have customized your configuration and
want to back it up for future use or apply it to
additional modems
•
You want to set up fixed IP addresses for your
computer(s)
Chapter 7: Advanced X7N Setup Options
X7N User Manual
Viewing the Advanced Setup
Options
For Advanced Setup options, click Advanced Setup from the
left-side menu of the Zoom Configuration Manager.
This link…
ATM
Opens a page that lets you…
Used to set up multiple ATM channels. Most
users will only do this if instructed by their
service provider.
WAN
Specify how the Wide Area Network (WAN)
ADSL setup is configured. Some of the values
need to be supplied by your ISP/DSL
provider.
LAN
Specify the settings that control the
connection between the X7N modem and
your computer. Set a fixed IP address for your
computer.
NAT
Virtual Servers Setup page: To direct
incoming traffic from the WAN side. A
maximum of 32 entries can be configured.
Port Triggering: To dynamically open up
ports in the firewall when an application on
the LAN initiates a TCP/UDP connection to
the remote application using a ‘Triggering
Port’. A maximum of 32 entries can be
configured.
DMZ Host: To forward IP packets from the
WAN that do not belong to any of the
applications configured in the Virtual Servers
table to the DMZ host computer.
47
SecurityÆ
IP Filtering
Outgoing: To block selected IP traffic by
setting up filters.
Incoming: To accept selected IP traffic by
setting up filters (when the firewall is enabled).
SecurityÆ
MAC
Filtering
Allows you to block access to the Internet
based on a device’s MAC address.
Parental
ControlÆ
Time
Restrictions
Allows control of when certain computers or
devices are allowed to access the Internet.
Parental
ControlÆ
URL Filter
To choose particular URLs to be excluded or
included by setting up a URL list. A maximum
of 100 entries can be configured.
QoS
(Quality of
Service)
This lets you assure better performance for
gaming and VoIP.
Queue Management Configuration: Allows
you to automatically mark incoming traffic
without reference to a particular classifier.
Queue Configuration: Allows you to
configure a maximum of 24 entries.
QoS Class: Allows you to configure network
traffic classes.
Routing
Default Gateway: Set up the routes on which
you want the X7N to send data that it receives
on a particular interface, such as a LAN or
Ethernet interface.
Static Route: Routes specify the IP address of
the next device, interface, or Internet
destination to forward data to, based on the
ultimate destination of the data. A maximum
of 32 routes can be configured.
RIP: Sets the X7N to use Routing
Information Protocol (RIP). Most users will
not set this.
Chapter 7: Advanced X7N Setup Options
X7N User Manual
DNS
DNS Server: Allows you to specify multiple
DNS servers. Typically, most users do not
need to enter a DNS server unless instructed
by their ISP.
Dynamic DNS: Allows you to map a
dynamic IP address to a static address allowing
your DSL router to be more easily accessed
from various locations on the Internet.
Typically used to host a website behind your
router without paying for a static IP address.
DSL
To set DSL settings. Modulation and capability
can be selected from lists on this page. DSL
Advanced Settings can also be found on this
page.
UPnP
Allows you to enable/disable UPnP. UPnP
allows other UPnP software or devices to
work together without user intervention. The
default setting for UpnP is Enabled.
When Enabled (default setting), attached
LAN devices performing DHCP
release/renew will have the router's LAN IP
assigned as the DNS Server and the X7N acts
as a DNS Proxy.
DNS Proxy
When Disabled, the X7N no longer acts as a
Proxy and assigns to LAN DHCP devices it's
own DNS servers that it uses (can be used if
the servers are down and you want to put in
your own DNS).
Interface
Group
To create mapping groups with appropriate
LAN and WAN interfaces to set up groups
that perform as independent networks
(utilizing multiple ports to PVC and bridging
groups).
IPSec
To add, edit, or remove IPSec tunnel mode
connections.
Certificate
Local: To add, view, or remove local
certificates used by peers to verify your
49
identity. A maximum of 4 certificates can be
stored.
Trusted CA (Certificate Authority): Add,
view, or remove CA certificates used by you to
verify peers’ certificates. A maximum of 4
certificates can be stored.
Multicast
Sets up IGMP protocol. Most users will only
do this if instructed by their service provider.
Changing Your WAN Settings
The WAN Configuration page of the X7N Configuration
Manager is used to change the advaced settings of your Wide Area
Network (WAN) connection. Most users should use the Basic
Setup to edit their WAN connection. To open this page, click
Basic Setup on the left-side menu.
To Edit a Previous Configuration:
If you already created a configuration (from the Basic Setup page
or from the WAN page at an earlier time), you can click Edit to
make changes to that configuration. Then use the Next and Back
buttons to navigate through a series of pages where you can make
changes to advanced parameters such as the ATM Traffic Class
and Encapsulation Mode, and enabling NAT settings, IGMP
Multicast, and WAN Service.
To Add a New Configuration:
If you want to add a new configuration from this page, start by
clicking Add. Then use the Next and Back buttons to navigate
through a series of pages where you can make changes to advanced
parameters such as the ATM Traffic Class and Encapsulation
Mode, and enabling NAT settings, IGMP Multicast, and WAN
Service.
Once you have made the changes you want on the first section,
click on Next to proceed to the following section. Repeat this until
you reach the WAN Setup – Summary page. Then click the
Save/Reboot button.
Chapter 7: Advanced X7N Setup Options
X7N User Manual
The following table describes the settings on the WAN
Configuration pages and the values that you can enter. The
settings displayed on the page will vary according to the protocol
you are using.
Setting
Description
PVC
Displays the value (PVC0 through
PVC3) of the selected Permanent
Virtual Circuit (PVC). You can set the
PVC value by entering it in the text box.
VPI
Virtual Path Identifier ranges from 0 –
256. Your DSL provider supplies the
VPI when you sign up for ADSL
service.
VCI
Virtual Circuit Identifier ranges from 0
– 65536. Your DSL provider supplies
the VCI when you sign up for ADSL
service.
ATM Traffic Class
These settings allow you to give priority
to data that is sent over the network.
Important! You must make
arrangements with your DSL provider
to use anything except UBR
(Unspecified Bit Rate) in the Traffic
Class setting. Your service provider will
also supply you with the Cell, Burst, and
Tolerance Rates.
Connection Type
Your Internet Service Provider supplies
this value.
If your service provider instructs you to
use 1483 Bridged mode, select 1483
Bridged + NAT to take advantage of
your modem’s advanced routing and
firewall features.
Encapsulation
Mode
The encapsulation value should match
your DSL provider’s encapsulation. The
51
value refers to the way that data is
passed over the Internet. An example
value is LLC (Logical Link Control).
Your DSL provider supplies this value
when you sign up for ADSL service.
User Name
Your DSL provider supplies this PPP
User Name when you sign up for ADSL
service.
Password
Your DSL provider supplies this PPP
password when you sign up for ADSL
service.
MTU
Maximum Transmission Unit. Largest
physical packet size, measured in bytes,
that the modem can send. Any messages
larger than the MTU have to be
fragmented before being sent.
NAT
Network Address Translation. By
default, this setting is Enabled. NAT
keeps a table of individual private IP
addresses in your network and refers to
the table when incoming requests are
made. If no matches are found, the
incoming data cannot come into your
network. An Enabled setting keeps
your IP addresses hidden from outside
users.
Service Name
This is an optional value that your
service provider may ask you to enter.
After you enter your values, click Save.
Chapter 7: Advanced X7N Setup Options
X7N User Manual
Changing Your LAN Settings
When would I need to change my LAN settings?
DHCP (Dynamic Host Configuration Protocol) is a protocol that
enables your modem to manage the assignment of IP addresses to
computers and devices on your Ethernet (LAN) network. Enabling
DHCP on your modem allows it to assign temporary IP addresses
to your computers whenever they connect to your network. You
can control the amount of time that lapses before a new address is
issued or renewed. You can extend the range of IP addresses that
are assigned to your network devices should you add new devices
to your network. You can also change the default LAN IP address
for your modem.
The following table shows you the values to enter. After you enter
the values, click Save/Reboot.
Setting
Description
IP Address
The IP address of your modem.
Subnet Mask
The modem's subnet mask address.
DHCP Server
Click Enable to turn on the DHCP
Server or Disable to turn it off.
Start IP Address
The first IP address of a range that you
specify using the Start and End IP
Address settings. Your modem's DHCP
server will assign the IP addresses in this
range at random to the computers and
devices in your network.
End IP Address
The last IP address of a range that you
specify using the Start and End IP
Address settings. Your modem’s DHCP
server will assign numbers from this
range at random to the computers and
devices in your network.
Leased Time
The maximum amount of time, in hours,
53
(hour)
that a device in your network will have
the IP address before a new one is issued
by the modem’s DHCP server.
Configuring Fixed DHCP
Mapping
Fixed DHCP mapping is used when you want the modem to
always assign the same IP address to a computer or gaming device.
You would want to do this if you were setting up a virtual server or
DMZ using this device.
To set up a device with Fixed DHCP Mapping:
Click Advanced SetupÆ LAN to open the LAN page.
Under Fixed IP Mapping click on Add Entries.
Enter the MAC Address of the computer or gaming station
that you wish to assign a fixed IP address to.
Tip: To find the MAC address of the devices connected to
your X7N refer to the Existing DHCP Clients table at the
bottom of the page.
Enter the IP address that you always want assigned to your
computer or gaming station. This address can be the one
already given to it on the DHCP Status page or can be an
unused IP address. For example if none of the devices on the
DHCP Status page have been assigned 192.168.1.25 you can
use that as the IP address.
Click Save/Apply to store your settings.
Creating a Virtual Server, a DMZ,
or Using Port Triggering
Chapter 7: Advanced X7N Setup Options
X7N User Manual
Do I need to create a virtual server, DMZ, or use
Port Triggering?
By default, your modem uses NAT to hide your computers from
users on the Internet; however, there may be times when you want
to allow access by outside users to a computer or gaming station on
your network. For instance, you would want to allow access if a
computer in your network is hosting Internet games or running a
web server. If you wish to set up your X7N for online gaming you
should refer to Chapter 5: Online Gaming to help you decide if a
Virtual Server, DMZ or Port Triggering is right for you.
Creating a Virtual Server
Before starting this section, you should set up a fixed DHCP
address for the computer or gaming station that you want to use
the virtual server with to prevent the IP address from changing in
the future
Click Advanced SetupÆ NATÆ Virtual ServersÆ Add to
open the Add Virtual Servers page.
For the server name check the list of predefined games and
applications to see if yours is on the list. If it is, go ahead and
select it. You will need to enter the IP address of your
computer or gaming station in the Server IP Address field but
the rest of the information will be filled out for you.
Click Save/Apply to save your new virtual server.
If your game or application was not on the list continue to step
5 to create a custom Virtual Server.
Enter a Custom Server name for your virtual server.
Enter the IP address on the computer or game station that you
want to use the virtual server with in the Server IP Address
field.
For each range of ports you need to open up enter the Starting
and Ending External Ports and the Protocol used. Your
game documentation should provide you with this information.
55
8
If you only need to open one port, enter that port number in
both the Start and End External Port fields.
Once you enter the External Ports, the Internal Port fields will
automatically be set to the same values. The Internal ports
cannot be changed.
10 If you know the Remote IP address of the device you are
connecting to, enter it under the Remote IP field. If you don’t
know it you can leave this field blank.
11 Click Save/Apply to save your new virtual server.
DMZ
Use this page to designate a computer or gaming station on the
Local Area Network as a DMZ (Demilitarized Zone). When you
set up a DMZ, all ports on that computer are opened up to all
Internet traffic – the computer is no longer protected by the X7N’s
NAT firewall. Caution should be used when setting up a computer
with a DMZ. A game station does not have the same security
issues as your computer so setting up a DMZ works well with your
game station.
You may want to create a DMZ if a computer in your network is
acting as a web server or hosting Internet games.
You need to manually assign an IP address to the DMZ.
DMZ Host IP Address: Enter the IP address of the computer or
gaming station designated as a DMZ.
Note: You need to give your LAN PC clients a fixed/static IP
address for DMZ to work properly. To do this, go to
Configuring Fixed DHCP Mapping on page 54.
Click Save/Apply.
Chapter 7: Advanced X7N Setup Options
X7N User Manual
Port Triggering
Port triggering allows a host machine to dynamically forward a
specific port back to itself and is a way to automate port
forwarding. When traffic is seen on an outgoing port any traffic
received on the corresponding incoming port will be forwarded to
your computer or gaming station.
To set up port triggering, follow the instructions below.
1 Click Advanced SetupÆ NATÆ Port Triggering.
2 Click Add to add a new Port Triggering rule.
3 Check the drop down list next to Server Name (check that
this is called server name). If your game or application is listed,
go ahead and select it.
4 Click Save/Apply.
If your game or application is not listed, enter a Custom
Name for your port triggering rule and go to step 5.
5 Enter the Start and End Trigger Ports in the text fields. Your
games documentation should supply you with this information.
6 Select the Protocol for the Trigger Protocol from the dropdown menu.
7 Enter the Start and End Open Ports in the text fields.
8 Select the Open Protocol from the drop-down menu.
9 Repeat steps 5-8 for each range of ports you want to trigger
open ports with. When you are finished go to step 10.
10 Click Save/Apply.
Note: To delete a previously created Trigger Port, click the
checkbox of the Trigger Port in the Trigger Port list and click
Delete. Then click Apply to save your settings.
Using IP Filters
Use the IP Filter Configuration page to set up IP filters to block
outgoing or allow incoming traffic into your computer from the
Internet. To open this page, click Advanced Setup Æ Security.
57
Then click on IP Filtering. Select Outgoing or Incoming
depending on which type of filter you want to set up.
Outgoing IP Filtering Setup:
By default, all outgoing IP traffic from LAN is allowed, but some
IP traffic can be blocked by setting up filters. Choose Add or
Remove to configure outgoing IP filters. Once you have set up the
IP filters you want, click the Save/Apply button.
Incoming IP Filtering Setup:
By default, all incoming IP traffic from the WAN is blocked when
the firewall is enabled. However, some IP traffic can be accepted
by setting up filters.
To filter Internet traffic, you must define one or more rules (that is,
criteria you want the information to meet before it can proceed).
As information comes in from the Internet, the X7N examines it
and—if it meets the rule—the information moves forward to its
destination on your computer or network. If it does not, it is
discarded.
The rule can be based on many characteristics, including the
network or Internet protocol it carries, the source IP address, the
port that the traffic is coming in on, and so forth.
Choose Add or Remove to configure incoming IP filters. Once
you have set up the IP filters you want, click the Save/Apply
button.
Using MAC Filtering
Use the MAC Filter Configuration page to block a device from
accessing the Internet. To open this page, click Advanced Setup
Æ Security. Then click on MAC Filtering. Select ADD to add
the MAC address of the device you wish to prevent from accessing
the Internet. If you do not know the MAC address Click on
STATUS Æ DHCP for a list of devices and their MAC address
that are connected to your X7N.
Chapter 7: Advanced X7N Setup Options
X7N User Manual
Setting Up a Time Restrictions
Do I need time restrictions?
Time restrictions can be used to prevent a user from accessing the
Internet during certain hours. For example you can use Time
restrictins to block a child from accessing the Internet until you are
home.
To open this page, click Advanced Setup Æ Parental Control.
Then click on Time Restrictions.
The following table describes the Time Restriction settings.
Setting
Description
User Name
The name you wish to give this rule.
MAC
Enter the MAC Address of the
computer you wish to block. To find
the MAC address of the devices
connected to your X7N are shown in
the Existing DHCP Clients table at the
bottom of the page.
Days of the Week
Select the days of the week that you
wish to block access on.
Start
Enter the starting time that you wish to
block access.
Stop
Enter the time that you wish to block
access until.
Remove
59
Setting Up a Static Routing Table
Do I need static routing?
Most users do not need to set up static routes. The default route
used in your modem will forward all packets correctly. However, if
you set up your network with different subnets, you can use static
routing to ensure your packets are handled correctly.
You can manually create a static route to tell the modem how to
reach a specific IP network. The route entry specifies a destination
network (or single host), together with a mask to indicate what
range of addresses the network covers, and a next-hop gateway
address or interface. If there is a choice of routes for a destination,
the route with the most specific mask is chosen.
To route to a destination that is not on any local network, a route
may be added via a gateway, for instance another router. The
gateway IP address must be on the same subnet as one of the
router's interfaces.
Click Routing from the left-side menu of the Zoom Configuration
Manager. Click Static Route. Click Add.
The following table describes Routing Table settings.
Setting
Description
IP Version
IPv4
IPv6
Destination IP
address / prefix
length
Enter the Destination Network
Address.
Interface
You can make a selection from the
drop-down menu.
Gateway IP
Address
Enter the Gateway IP address of your
destination’s subnet. The HOP gateway
must be on the same subnet as the
Chapter 7: Advanced X7N Setup Options
X7N User Manual
modem.
Metric
The number of routers that the data
packets go through (optional). When
adding a static route, if you know how
many “hops” or “routers” a packet must
go through to reach the destination
network, then you can add it. This is
usually not a mandatory requirement.
If you change any of the settings, click Save/Apply.
If you want to remove any of the settings, click the check box next
to Remove and then click the Remove button.
Adding a DNS Server Name
Do I need to add a DNS server name?
Typically you should not need to enter a DNS server name as it is
assigned automatically when your connection is established.
However, your ISP may instruct you to enter an IP address for a
DNS server name. To do this, follow the instructions below:
Check the box Use the Following Static DNS IP Address.
In the Primary DNS Server and Secondary DNS Server text
boxes, enter the IP addresses of the DNS servers that your ISP
instructed you to enter.
Click Save/Reboot.
61
Using the ADSL Settings
Do I need to change my ADSL settings?
Typically you should not need to change your ADSL settings;
however, you may be instructed to do so by your service provider.
Or, if you are having problems establishing a physical layer
connection, you may want to change a couple of the settings on the
DSL page.
Click DSL under Advanced Setup from the left-side menu of the
Zoom Configuration Manager.
The following table shows you the values to enter. After you enter
the values, click Save/Apply.
Setting
Description
BitSwap
Enables or disables bit swapping in both
upstream and downstream directions. If you
experience frequent connection drops, it may
help to change the bit swap settings.
Enabling or Disabling UPnP
Universal Plug and Play (UPnP) with Internet Gateway Device
(IGD) protocol is installed in X7N units when they are shipped by
Zoom. This means that other devices plugged into your computer
or network (for example, a gaming application, router, or
stand-alone firewall) that use UPnP should automatically detect the
X7N and make the needed configurations for them to work
together. There is no setup for you to do. Change this setting only
if you have a good reason to do so.
To change the status of Universal Plug and Play, go to the LAN
page under the Advanced Setup link.
Chapter 7: Advanced X7N Setup Options
X7N User Manual
Setting
Description
Enable UPnP
Select this check box to enable or
disable Universal Plug and Play. By
default UPnP is enabled.
Click Save/Apply.
63
8
Wireless Options
To configure wireless features, click Wireless from the left-side
menu of the Zoom Configuration Manager.
This link…
Basic
Security
MAC
Filtering
Opens a page that lets you…
Configure basic features of the wireless LAN
interface. See Chapter 3: Setting Up Your
Wireless Network on page 21.
Configure security features of the wireless
LAN interface. See Chapter 4: Setting
Wireless Security on page 35.
Configure wireless MAC filtering to block
Internet access.
WDS
Configure the WDS (Wireless Distribution
System) feature of the wireless LAN interface.
Advanced
Configure the advanced features of the
wireless LAN interface.
Client Info
Shows authenticated wireless clients and their
status.
Wireless MAC Filtering
Most users will not need this feature.
However, if there is a PC or other device on the X7N network that
you don’t want using the Internet, you can use MAC address
filtering to deny the device Internet access. (That computer or
Chapter 8: Wireless Options
X7N User Manual
device will still be able to communicate with other devices on the
LAN, such as printers.) Otherwise, as an added layer of security
you can set the X7N up to only allow the MAC address of your
wireless devices to access the internet.
To block Internet access, click Advanced Setup on the left-side
menu of the Zoom Configuration Manager. Click Wireless. Then
click MAC Filtering. Follow the instructions below:
From the Select SSID drop-down menu, select the name
associated with the MAC address.
For the MAC Restrict Mode, select Disabled, Allow, or
Deny.
Click Add.
Click Save/Apply changes after you finish adding or removing
information.
If you want to remove any of the settings, click the check box
next to Remove and then click the Remove button.
WDS
You can select WDS (also known as Wireless Bridge) to disable
access point functionality. Selecting Access Point enables access
point functionality. WDS functionality will still be available and
wireless stations will be able to associate to the AP.
Select Disabled in Bridge Restrict to disable Wireless Bridge
restriction. Any wireless bridge will be granted access.
Select Enabled or Enabled (Scan) to enable wireless bridge
restriction. Only those bridges selected in Remote Bridges will be
granted access.
Click Refresh to update the remote bridges. Wait for a few
seconds to update.
Click Save/Apply to configure the wireless bridge options.
65
9
Management and Diagnostics
Please read this chapter if you want to perform modem management
functions, as discussed below, or if you want to run diagnostics to
diagnose a modem problem. If you don’t want to do either of these
things, your modem is probably set up and ready to go. You may want
to read Appendix C: Top and Back Panels on page 91, for details
about the modem’s lights and back panel jacks.
Management Buttons
The buttons in the Management group of the Zoom
Configuration Manager are typically used for administrative tasks,
such as upgrading firmware, changing your Zoom Configuration
Manager password, etc.
The following table lists each button in the Management group
and gives a brief description of the settings you can specify.
Open page
from…
This button…
Opens a page that
lets you…
ManagementÆ
Settings
Backup
Save your current
configuration
settings to a file so
that they may be
restored at a later
time.
Update
Upload your
previously saved
settings.
Restore Default
Restore the X7N
Chapter 9: Management and Diagnostics
X7N User Manual
settings to the
factory defaults.
Management
System Log
By default the
System Log is
disabled. You must
Enable it and then
click View System
Log.
View data generated
or acquired by
routine system
communication with
other devices. This
information does
not necessarily
represent
unexpected or
improper
functioning and is
not captured by the
system traps that
create alarms. You
can save the system
log to a file.
Management
SNMP Agent
Access the SNMP –
configuration page.
Simple Network
Management
Protocol (SNMP)
allows a
management
application to
retrieve statistics
and status from the
SNMP agent in this
device.
Management
TR-069 Client
Access to a page
that allow an AutoConfiguration
Server (ACS) to
67
perform autoconfiguration,
provision,
collection, and
diagnostics to the
ADSL modem.
Select the desired
values and click
Save to configure
the TR-069 client
options.
Management
Internet Time
Access to a page
that allows you to
set up the X7N to
automatically
synchronize with
Internet time
servers.
ManagementÆ
Access Control
Services
A Service Control
List (“SCL”) enables
or disables router
services (for LAN /
WAN such as FTP,
HTTP, ICMP, and
TELNET) from
being used.
ManagementÆ
Access Control
Passwords
Manage the User
IDs and passwords
that can access the
Zoom
Configuration
Manager. This is
where you can
change the default
password supplied
to you with the
X7N.
Management
Update
Software
Specify the path to
the upgrade file you
need to update your
Chapter 9: Management and Diagnostics
X7N User Manual
firmware. Use the
Browse button on
this page to navigate
to the file, then click
the Update
Software button to
perform the
firmware update.
Management
Save / Reboot
Click the Save /
Reboot button on
the Save / Reboot
page to reboot the
modem.
Backing Up Your Configuration
Users who change the Configuration Manager settings for the X7N
may want to back up their settings. This will enable them to restore
those settings at a later time, if needed.
This feature may be especially useful when you receive firmware
updates from Zoom. Installing the update may overwrite your
customized settings with default values. Before you update the
firmware, backup your configuration. Then, after the firmware has
been updated, restore your configuration.
Note:
You do not need to back up the default settings. This is because
you can easily restore the defaults by clicking Management Æ
Settings Æ Restore Default. For more information, see
Resetting Default Settings on page 错误！未定义书签。.
To back up your current configuration
Use the Backup page of the Configuration Manager to save your
modem’s current configuration to a file on your computer.
69
1
Click on the Management link on the left pane of the window.
Then click on the Settings link. Then click on the Backup
link.
On the Backup page, click Backup Settings to download a
configuration file from the X7N to a folder on your computer.
Be sure to note the name (backupsettings.conf) and location.
You will need this information if you ever want to restore the
X7N to this backed-up configuration. (You can change the
name of the file and specify a location for it on your computer
after it is downloaded.)
To restore a configuration
1 Click on the Management link on the left pane of the window
in the Configuration Manager.
2 Then click on the Settings link.
3 Then click on the Update link.
4 On the Update Settings page, click Browse and navigate to
the file containing the configuration to which you want the
X7N restored.
5 Click Update Settings.
Resetting Default Settings
If you have changed the system settings on your X7N and for
some reason want to restore them to the factory default settings,
you can do so in one of two ways: You can perform a software
reset or a hard reset.
To reset using the X7N’s Web interface
If you can open your Web browser and access your X7N’s
Configuration Manager, do the following to perform a software
reset:
Chapter 9: Management and Diagnostics
X7N User Manual
1
Log into the Zoom Configuration Manager. (See page 13 if
you need help logging in.)
Click on the Management link on the left pane of the window.
Then click on the Settings link. Then click on the Restore
Default link.
Click the Restore Default Settings button.
To perform a hard reset
If you lose your link to the unit and cannot communicate with it
via the Web browser, do the following to perform a hard reset:
Press the RESET button on the modem’s back panel for five
seconds.
You are now guaranteed that all system settings are restored to the
X7N’s factory defaults.
Remote Access to Your Modem
Configuration Settings
If you want to be able to access your modem Configuration
Manager to change or view your configuration settings remotely:
Click on Management. Click on Access Control, and
then select the enable check box for Http WAN to allow
access from a remote PC. Click Save/Apply and wait several
seconds for the settings to be saved.
Click on Status from the left pane of the Zoom
Configuration Manager. Click on WAN. Write down the
public IP address displayed under WAN Info.
Type this public IP address into the browser of your remote
PC.
At the log in prompt, enter the User Name and Password
shown below:
User Name: support
Password: support
71
5
You can now view or make changes to your modem’s
configuration from your remote PC.
TR-069
The TR-069 option of the X7N Configuration Manager opens a
page where you can allow an Access Control Server (ACS) to
control and configure your X7N.
This feature must be supported by your service provider and
should be used only if the provider instructs you to enable it.
Click Management from the left-side menu of the Zoom
Configuration Manager.
Then click TR-069 Client.
After you make changes on the TR-069 client – config page,
click Save.
Changing User Names and
Passwords
Use the Passwords page to manage the user names and passwords
that can access the Zoom Configuration Manager. To open this
page, click Management Æ Access Control Æ Passwords.
When you installed the X7N and tried to open the Zoom
Configuration Manager, you were prompted for a User Name
and Password in order to gain access. (The default User Name and
Password were supplied to you in the section Establishing
Communication.)
If you want, you can change the default password. Changing the
password is not required, but as a good security measure, we
recommend it.
Chapter 9: Management and Diagnostics
X7N User Manual
To change the default password
Access to your DSL modem is controlled through three user
accounts: admin, support, and user.
Select the User Name for which you want to change the
Password from the drop-down menu of the Passwords page of
the Configuration Manager.
Enter the current password in the textbox Old password.
Choose the password you would like to replace it with (up to
16 characters without any spaces) and enter it in the textbox
New password.
Retype the password in the textbox Confirm password.
Click on Save/Apply.
Diagnostics
You can use the Diagnostics page of the Configuration Manager
to run a series of diagnostic tests of your system software and
hardware connections.
73
Appendix A:
Troubleshooting Tips
The following are some problems you may experience and some
possible solutions to remedy the situation.
Problem
I am unable to connect to the Internet.
Solution
There are several issues that could cause this problem. Check these
items:
• Verify that the PWR light on the modem is on. If it is off check
that the modem is plugged into an wall outlet and that the
POWER button on the back of the modem is pushed in. If the
light does not turn on, make sure there is power going to the
outlet you are using. If the unit still doesn’t work contact Zoom
Technical Support. See Appendix G on page 106 for contact
information.
• If you are using a wireless device, try connecting a computer
directly to the X7N’s Ethernet ports. If a computer directly
connected to the X7N works, then the problem is with your
wireless connections. See the wireless troubleshooting tip on
page 80.
• If you cannot access the Internet with a computer directly
connected to the X7N’s Ethernet port, check your Ethernet
connection. Most computers have a power light next to the
Ethernet jack (to indicate the Ethernet cable is properly
connected). Verify that this light is on and that the Ethernet
light on the front of the X7N is on. If the Ethernet light is off
on either the X7N or on the computer, verify that the cable is
properly pushed in. If the light still doesn’t turn on, you should
try another Ethernet cable.
• Check your phone cable and splitters. Replace your phone cable
with a tested working phone cable. If you have installed a
Appendix A: Troubleshooting Tips
X7N User Manual
splitter between the X7N and the phone jack, remove this
splitter. If this solves the problem you may need to replace this
splitter. When testing the X7N, make sure that the telephones
in your house are not in use. If the problem only exists when a
particular phone is in use, then you may need to install a filter
on that phone; or if there is an existing filter, you should replace
it.
• Try turning your computer off and then on. This ensures that
your computer gets a correct IP address from the X7N.
• Check your modem’s DSL light.
If the light is blinking then the X7N was unable to
make a DSL connection. Go to My X7N’s DSL
light continually blinks and does not stay
solidly lit.
If the DSL Light is solid go to My X7N’s DSL
light is solidly lit, but I cannot connect to the
Internet.
Problem
My X7N’s DSL light continually blinks and does not stay solidly lit.
Solution
There are several issues that could cause this problem. Check these
items:
•
Ensure that the phone cord is firmly plugged into the wall
jack and the DSL jack on the back of the X7N.
•
Verify that the jack the phone jack your X7N is connected to
is enabled for ADSL service. Unless your service provider has
enabled it, you cannot use a standard telephone jack for
ADSL service.
•
Your phone cord may be defective. Replace the phone cord
with a known good one.
•
If your DSL modem is installed onto the same phone jack as
a DSL filter, the filter may be defective. Please remove the
filter from the line and plug the DSL modem into the phone
jack. If this solves the problem, replace the defective filter.
Appendix A: Troubleshooting Tips
75
•
Verify that none of the phones are in use when testing the
X7N. If the problem appears only when you are using your
phone than you either need to install a filter on that phone or
if there is an existing filter you should replace it with a known
working one.
•
You may be having an issue with the phone wiring inside your
house. Try plugging the X7N into different phone jacks to see
if that solves the problem. If you know where your phone line
enters your house (often called the Demarc Point and is
typically a gray box found either in your basement, your
garage, or on the outside of the house) and you have easy
access to the Demarc Point, try plugging your X7N at this
point. If this solves your problem you may need a
professional to repair your inside phone wiring.
Problem
My X7N’s DSL light is solidly lit, but I cannot connect to the
Internet.
Solution
There are several issues that could cause this problem. Check these
items:
•
Ensure that you are using the correct VPI, VCI and
Encapsulation settings. If you don’t know what they are,
please refer to the ADSL Settings Table in Appendix B.
•
If your Encapsulation begins with PPP, ensure that you
have typed your ADSL User Name and Password correctly.
(Note that this is NOT the User Name and Password you
used to log into the Zoom Configuration Manager on
page 13.) To verify that your PPP User Name and Password
are correct, login into the configuration manager.
Open the Zoom Configuration Manager by entering the
following in your Web browser's address bar:
http://192.168.1.1
In the Enter Network Password dialog box, type the
following User Name and Password in lower case, then click
OK.
Appendix A: Troubleshooting Tips
X7N User Manual
User Name: admin
Password: zoomadsl
(The User Name and Password entered here are
not the same as the user name and password that
your Internet service provider may have given
you.)
On the left-hand side, click Diagnostics to start the
diagnostic test. In the Test the Connection to your
Internet Service Provider box if the Test PPP Server
Connection tests passes but the Test Authentication with
your ISP test fails, then your PPP User Name and Password
are wrong. If you are having problems remembering your
PPP User Name and Password please see the solution to the
next troubleshooting problem My DSL connection requires
a User Name and Password, but I don’t know where to
find this information on page 78.
•
Verizon users who are replacing an existing modem in
California, Florida, or Texas may need two wait 2 hours after
unplugging the existing modem for Verizon to release the line
before it is available for use. If this applies to you, power
down your X7N and wait 2 hours before trying to connect
again.
•
Verify that your service provider’s ADSL connection is
functioning properly. (Place a call to your service provider’s
customer support department to verify this.)
•
Windows users only: Verify that the Web browser on the
computer on which you installed the software is configured
for a network connection (this might be called a “Local Area
Network” or “broadband” connection). If you need help
configuring your Web browser, refer to Appendix E:
Configuring Your Web Browser on page 99.
•
Verify that your TCP/IP network settings are properly
configured on your computer. To do this, refer to the
appropriate section.
¾ If you are using Macintosh, see Macintosh TCP/IP
Settings on page 93.
Appendix A: Troubleshooting Tips
77
¾ If you are using Windows, see Windows TCP/IP
Settings on page 95.
Problem
My DSL connection requires a User Name and Password, but I
don’t know where to find this information.
Solution
•
If you are replacing a modem, use the same User Name
and Password that you used for the modem you’re
replacing.
•
If you don’t know what that is, here are some suggestions:
¾ If you have an email address with the service
provider like name@verizon.net, the User Name
is likely to be the word name in this example.
NAME will not work, since upper and lower case
matter. There are some exceptions to this
however. Some AT&T customers especially in old
BellSouth areas have a separate network User
Name and password used to verify their DSL
connection. Please see the AT&T support website
on how to reset your User Name and password.
¾ If you have a service provider Password, that’s
probably your Password for Internet access too.
¾ You may also be able to change your User Name
and Password so that you can use the new User
Name and Password with your Zoom modem.
Some service providers like Verizon provide a
software tool that lets you do that if your old
modem is still plugged in. Many service providers
allow you to change your User Name and
Password on their support website in case you
have forgotten this information.
•
If you are not replacing a modem, you may need to use
your service provider’s Internet software tool or speak
Appendix A: Troubleshooting Tips
X7N User Manual
with the service provider to find out your User Name and
Password.
•
Remember that the User Name and Password are case
sensitive, so it matters whether a letter is a capital letter or
a small letter; so does the difference between the letter O
and the number 0.
•
Once you have a working User Name and Password, be
sure to remember them. You may want to write them on
the bottom of your modem or in a document called
ModemSettings.
•
We are talking here about the User Name and Password to
get into the Internet, NOT the User Name and Password
used to get into your modem’s configuration page.
Problem
Autodetecting the connection through either the Install Wizard or
the Zoom configuration manager was unable to detect my
connection.
Solution
There are several issues that could cause this problem. Check these
items:
•
Your DSL connection is not established. You must wait for
your DSL connection to be established before running the
autodetect. If you are having problems establishing your DSL
connection see the My X7N’s DSL light continually blinks
and does not stay solidly lit tip on page 75.
•
You are trying to detect a static IP connection. Autodetect
only works with connections that use DHCP. Typically you
have to request and pay extra for a static IP connection. If
you know this applies to you, then you must configure your
connection manually. See Chapter 1 for more information on
configuring your connection manually.
Appendix A: Troubleshooting Tips
79
•
Autodetect may not be able to detect your connection. In this
case you may need to manually configure your connection.
See Chapter 1 for configuring your connection manually.
Problem
My computer/devices are not connecting wirelessly to the X7N.
Solution
Try the following:
• Check your wireless security settings on your X7N and verify
that your device is using the same settings.
•
Check the signal strength of your wireless connection. Most
wireless adapters have some type of signal strength meter that
shows how strong your wireless signal is. Windows users,
click the Wireless icon in your system tray to check signal
strength. If your signal strength is not strong enough, try the
following:
¾
¾
¾
•
Reorient the receiving antenna on your X7N.
Move the X7N to another area.
Move the device trying to access the X7N to a
different location.
Change the wireless channel. In the unlikely event that you
experience performance issues with your wireless network,
you may want to set your network up on a channel that’s
different from the factory-set channel of 10. To do that,
follow these steps:
Open the Zoom Configuration Manager by
entering the following in your Web browser's
address bar: http://192.168.1.1
In the Enter Network Password dialog box,
type the following User Name and Password in
lower case, then click OK.
User Name: admin
Password: zoomadsl
Appendix A: Troubleshooting Tips
X7N User Manual
(The User Name and Password entered here are
not the same as the user name and password that
your Internet service provider may have given
you.)
On the Basic Setup page, click Wireless on the
left-side menu to open the Wireless page. Click
Advanced on the left-side menu.
On the Wireless - Advanced page, from the
Channel drop-down menu, select a different
channel, such as 1 or 6.
Be sure to click Save/Apply after you change the
channel. All devices connecting wirelessly to the
X7N will automatically switch to the new channel.
Problem
When I run the Zoom Install Wizard it reports that my DSL
modem is not found.
Solution
•
Verify that your X7N is powered on. The Power led should
be on.
•
You are using Windows Vista or Windows 7 and Telnet is not
enabled.
To enable Telnet:
1 Click Start, select Control Panel, then double-
click Programs and Features.
2 In Programs and Features, in the Tasks pane,
click Turn Windows features on or off.
Vista users only: At the User Account
Control message, click Continue.
3 In the Windows Features dialog box, select
Telnet Client, click OK, and wait while the
Appendix A: Troubleshooting Tips
81
feature is configured. This normally takes about
2 minutes.
4 In the Uninstall or Change a Program
window, click the Close box to exit.
•
You unplugged some other ADSL modem, a
router, or some other Ethernet device from your
computer and then did not power-cycle your
computer. If this applies to you, try turning your
computer off and then on. This ensures that your
computer gets a correct IP address from the X7N.
•
Your Zoom modem's Ethernet cable is not
plugged in properly or is defective. Please check
this cable.
•
Your computer is set to use static IP addressing.
This needs to be changed to Dynamic Addressing
to use the Install Assistant, and you can later go
back to static IP addressing if that is appropriate.
To use Dynamic Addressing for the Install
Assistant,
Problem
I cannot log into the Zoom Configuration Manager. I have
typed http://192.168.1.1 but I am not prompted for a User Name
and Password.
Solution
There are several issues that could cause this problem. Check these
items:
•
If you are using a Macintosh computer, your TCP/IP settings
may not be properly configured. See page 93 for more
information.
•
If you are using Mac OS X 10.3 and above, renew your IP
address: Point to System Preferences, then choose Network.
Click the Configure button and then the Renew DHCP
Lease button.
Appendix A: Troubleshooting Tips
X7N User Manual
•
If you are using a Windows computer, perform a
Release/Renew operation:
¾ Windows 7/Vista/2000/XP users: From the
desktop, click the Start button, then point to All
Programs (for Windows 2000 point to Programs
instead of All Programs), point to Accessories, and
then right-click on Command Prompt and select
Run as administrator. Click Yes at the User Account
Control box. Type ipconfig /all and press the Enter
key on your keyboard. In the subsequent dialog box,
make sure the NIC adapter is listed, type ipconfig
/release and then ipconfig /renew. Then type
192.168.1.1 into your browser’s address bar, and the
Network Password box should display.
¾ For Windows 95/98/Me users: From the desktop,
click the Start button and the point to Run. Type
winipcfg, and click OK. In the subsequent dialog box,
make sure the NIC adapter is highlighted in the
drop-down list, click Release and then click Renew.
Then type 192.168.1.1 into your browser’s address bar,
and the Network Password box should display.
Problem
The computer on which I initially installed the X7N on is
connected to the Web, but devices connected wirelessly to the
X7N are unable to connect to the Internet.
Solution
•
Try powering off then powering on each device on your
network.
•
Verify that the devices on your wireless network are using
Dynamic Host Configuration Protocol (DHCP). This is also
known as dynamic IP addressing. Depending on your device,
this may be controlled by an Obtain an IP address
automatically option. If you need help, refer to the
documentation that came with your network device or
contact its manufacturer. If you are using a Windows, Mac or
Linux computer, refer to Appendix D: TCP/IP Network
Appendix A: Troubleshooting Tips
83
Settings on page 93 for directions on configuring your
computer for DHCP.
•
Your problem might be in the wireless connection. Try the
steps in My computer/devices are not connecting
wirelessly to the X7N troubleshooting tip on page 80.
Problem
The computer on which I initially installed the X7N on is
connected to the Web, but the computers connected through my
network device cannot access the Internet.
Solution
The problem is most likely with your network device (such as a
wireless access point, router, hub, or switch). Check these items:
•
Try rebooting each computer on your network. For example,
if you are using a router, reboot each computer that is
connected to the router. This will allow for the computers to
release and renew their IP addresses.
•
If you are using a wireless access point or a router, verify that
the device is using Dynamic Host Configuration Protocol
(DHCP). This is also known as dynamic IP addressing.
Depending on your device, this may be controlled by an
Obtain an IP address automatically option. If you need
help, refer to the documentation that came with your network
device or contact its manufacturer.
•
Refer to the documentation provided with your network
device or contact its manufacturer for assistance.
Appendix A: Troubleshooting Tips
X7N User Manual
Appendix B: ADSL
Internet Settings Tables
These tables are for customers where ADSL settings were not
automatically detected by the X7N Install Assistant, and whose
service providers do not supply them with the ADSL settings to
connect to the Internet. Many ADSL providers use different
settings depending on the region in which they are operating,
which is why there may be more than one setting for your service
provider. We post updated tables on our Web site. If your country
is not listed in the tables below, please consult www.zoomtel.com
Note to USA customers
If your ADSL service provider is not shown below, first use the
settings for Service Provider Not Shown at the bottom of the
table. If those settings do not work, use the settings for the
company that provides local telephone service in your area.
Table A: USA
ISP
VPI
VCI
Encapsulation
All Tel (1)
35
PPPoE LLC
All Tel (2)
35
1483 Bridged IP LLC
AT&T (1)
35
PPPoE LLC
AT&T (2)
35
1483 Bridged IP LLC
AT&T (3)
35
1483 Bridged IP LLC
August.net (1)
35
1483 Bridged IP LLC
August.net (2)
35
1483 Bridged IP LLC
BellSouth
35
PPPoE LLC
Castle.Net
96
1483 Bridged IP LLC
CenturyTel (1)
35
PPPoE LLC
CenturyTel (2)
35
1483 Bridged IP LLC
Appendix B: ADSL Internet Settings Tables
85
Coqui.net
35
PPPoA LLC
Covad
35
PPPoE LLC
Crocker
Communications
35
PPPoE LLC
Earthlink (1)
35
PPPoE LLC
Earthlink (2)
35
PPPoE LLC
Earthlink (3)
35
PPPoE VC-MUX
Earthlink (4)
32
PPPoA LLC
Eastex
100
PPPoA LLC
Embarq
35
1483 Bridged IP LLC
4DV.net
32
PPPoA VC-MUX
Frontier
35
PPPoE LLC
Grande
Communications
34
PPPoE LLC
GWI
35
1483 Bridged IP LLC
Hotwire
35
1483 Bridged IP LLC
Internet Junction
35
1483 Bridged IP LLC
PVT
35
1483 Bridged IP LLC
Qwest (1)
32
PPPoA VC-MUX
Qwest (2)
32
PPPoA LLC
Qwest (3)
32
PPPoE LLC
Qwest (4)
32
1483 Bridged IP LLC
SBC (1)
35
PPPoE LLC
SBC (2)
35
1483 Bridged IP LLC
SBC (3)
35
1483 Bridged IP LLC
Socket (1)
35
1483 Bridged IP LLC
Socket (2)
35
1483 Bridged IP LLC
Socket (3)
35
PPPoE LLC
Sonic
35
1483 Bridged IP LLC
Appendix C:Top and Back Panels
X7N User Manual
SouthWestern Bell
35
1483 Bridged IP LLC
Sprint (1)
35
PPPoA LLC
Sprint (2)
35
PPPoE LLC
SureWest
Communications (1)
34
1483 Bridged LLC Snap
SureWest
Communications (2)
32
PPPoE LLC
SureWest
Communications (3)
32
PPPoA LLC
Toast.Net
35
PPPoE LLC
Uniserve
33
1483 Bridged IP LLC
US West
32
PPPoA VC-MUX
Verizon (1)
35
PPPoE LLC
Verizon (2)
35
1483 Bridged IP LLC
Appendix B: ADSL Internet Settings Tables
87
Table B: Countries Other Than The USA
ISP
VPI
VCI
Encapsulation
Australia - Telstra
35
PPPoA LLC
Argentina - Telecom
33
PPPoE LLC
Argentina Telefonica
35
PPPoE LLC
Argentina
33
PPPoA VC-MUX
Belgium-ADSL Office
35
1483 Routed IP LLC
Belgium - Turboline
35
PPPoA LLC
Bolivia
34
1483 Routed IP LLC
Brazil - Brasil Telcom
35
PPPoE LLC
Brazil - Telefonica
35
PPPoE LLC
Brazil - Telmar
33
PPPoE LLC
Brazil - South Region
32
PPPoE LLC
Colombia - EMCALI
33
PPPoA VC-MUX
Columbia - ETB
33
PPPoE LLC
Costa Rica - ICE
50
1483 Routed IP LLC
Denmark-Cybercity,
Tiscali
35
PPPoA VC-MUX
France (1)
35
PPPoE LLC
France (2)
67
PPPoE LLC
France (3)
35
PPPoA VC-MUX
Germany
32
PPPoE LLC
Hungary - SciNetwork
35
PPPoE LLC
Iceland - Islandssimi
35
PPPoA VC-MUX
Iceland - Siminn
48
PPPoA VC-MUX
Israel
35
PPPoA VC-MUX
Italy
35
PPPoA VC-MUX
Appendix C:Top and Back Panels
X7N User Manual
Jamaica (1)
35
PPPoA VC-MUX
Jamaica (2)
35
PPPoA VC-MUX
Jamaica (3)
35
1483 Bridged IP LLC SNAP
Jamaica (4)
35
1483 Bridged IP LLC SNAP
Kazakhstan
33
PPPoA VC-MUX
Mexico
35
PPPoE LLC
Netherlands - BBNED
35
PPPoA VC-MUX
Netherlands - MX
Stream
48
PPPoA VC-MUX
New Zealand Slingshot
100
PPPoA VC-MUX
Portugal
35
PPPoE LLC
Puerto Rico Coqui.net
35
PPPoA LLC
Saudi Arabia (1)
33
PPPoE LLC
Saudi Arabia (2)
35
PPPoE LLC
Saudi Arabia (3)
33
1483 Bridged IP LLC
Saudi Arabia (4)
33
1483 Routed IP LLC
Saudi Arabia (5)
35
1483 Bridged IP LLC
Saudi Arabia (6)
35
1483 Routed IP LLC
Spain - Albura, Tiscali
32
PPPoA VC-MUX
Spain - Colt Telecom,
Ola Internet
35
PPPoA VC-MUX
Spain - EresMas,
Retevision
35
PPPoA VC-MUX
Spain - Telefonica (1)
32
PPPoE LLC
Spain - Telefonica (2),
Terra
32
1483 Routed IP LLC
Spain - Wanadoo (1)
35
PPPoA VC-MUX
Spain - Wanadoo (2)
32
PPPoE LLC
Spain - Wanadoo (3)
32
1483 Routed IP LLC
Appendix B: ADSL Internet Settings Tables
89
Sweden - Telenordia
35
PPPoE
Sweden - Telia
35
1483 Routed IP LLC
Switzerland
35
PPPoE LLC
Trinidad & Tobago TSTT
35
PPPoA VC-MUX
Turkey (1)
35
PPPoE LLC
Turkey (2)
35
PPPoA VC-MUX
United Kingdom (1)
38
PPPoA VC-MUX
United Kingdom (2)
38
PPPoE LLC
38
PPPoE VC-MUX
50
PPPoA LLC
Venezuela - CANTV
33
1483 Routed IP LLC
Vietnam
35
PPPoE LLC
Vietnam - VDC
35
PPPoE LLC
Vietnam - Viettel
35
PPPoE LLC
Vietnam - FPT
33
PPPoE LLC
United Kingdom AOL
United Kingdom Karoo
Appendix C:Top and Back Panels
X7N User Manual
Appendix C: Top and
Back Panels
The following table describes each light on the top panel.
Light
Power
Description
Lights when the X7N is plugged into a power
source.
DSL
Blinks when the X7N is performing its startup
sequence. Stays on solid when the unit has synched
up with its ADSL connection.
Note: If the light fails to switch from blinking to
steady after a minute or two, check with your ADSL
provider that the ADSL connection is activated, or
refer to Appendix A: Troubleshooting Tips on
page 73.
Internet
Blinks when data is sent and received.
Ethernet Lights when the Ethernet port of the X7N is
plugged into the Ethernet port of a powered-up
[1-4]
device. Blinks when there is data activity.
WLAN
Lights when the Wireless Local Area Network is
running and enabled. Blinks when data is sent.
The following table describes each item on the back panel.
Port
Description
DSL
Jack to connect the modem to the ADSL telephone
wall jack.
Ethernet
[1-4]
LAN ports that can connect the unit to access points,
network hubs, or the Ethernet ports of a computer.
Power
Port to connect the unit to the X7N’s power cube.
RESET
In the unlikely event that you need to reset the modem
to its system default settings (necessary if
communication link is lost), you can press the RESET
button for 5 seconds.
Appendix C: Top and Back Panels
91
Press the WPS button on your Router and hold it in
for seven (7) seconds until the Wireless LED starts
WPS
blinking rapidly. Click or press the WPS button on the
client device. This button may be a physical button on
the unit or a software button in its application. Refer to
your client device's documentation for further
instructions, if necessary.
ON/OFF Button when pressed once turns the modem’s power
ON. When pressed again turns the modem’s power
OFF.
Appendix C:Top and Back Panels
X7N User Manual
Appendix D: TCP/IP
Network Settings
If you are using a Mac computer, you must ensure that your
computer’s TCP/IP network settings are configured properly.
Otherwise, you will not be able to connect to the Internet.
Note:
If you are using a Windows computer, you do not have to
configure the TCP/IP settings if you are using DHCP because
your Windows computer will automatically configure them for you.
If you are not using DHCP, you will need to set up the TCP/IP
settings for your Windows computer. Windows users who are
troubleshooting the X7N will need to verify the TCP/IP settings.
Depending on your operating system, follow the steps in the
appropriate section to ensure your TCP/IP settings are correct.
•
If you are using Macintosh, see Macintosh TCP/IP
Settings on page 93.
•
If you are using Windows, see Windows TCP/IP Settings
on page 95.
Macintosh TCP/IP Settings
How you configure your Macintosh computer’s network settings
differs, depending on your Mac OS. For OS X, follow the
instructions below. Otherwise, go to page 94.
Mac OS X 10.7 (Lion), 10.6 (Snow
Leopard), and 10.5 (Leopard)
From the Dock or Apple menu, select System Preferences
and then Network.
Select your connection method, normally Ethernet for a wired
connection.
Appendix D: TCP/IP Network Settings
93
3
On the right pane, select Using DHCP from the Configure
IPv4 (for Mac OS X v10.7 and v10.6) and Configure (for Mac
OS X v10.5) drop-down menu. All of the text fields should be
left blank.
Click Apply.
Mac OS X 10.4 and 10.3
From the Dock or Apple menu, select System Preferences
and then Network.
Select your connection method, normally Built-in Ethernet
for a wired connection.
Make sure the TCP/IP tab is selected, and then select Using
DHCP from the Configure IPv4 drop-down menu. All of the
text fields should be left blank.
Click Apply Now.
Mac OS 7.6.1 - 9.2.2
From the Apple menu, choose Control Panels and then
TCP/IP to display the TCP/IP Window.
Under Connect via:, select Ethernet built-in.
Under Configure:, select Using DHCP Server. Do not enter
anything in the DHCP Client ID field.
Close the TCP/IP Window. You will be asked if you want to
save the changes. Click Save.
Continue with Establishing Communication on page 13.
Appendix D: TCP/IP Network Settings
X7N User Manual
Windows TCP/IP Settings
How you configure your Windows computer’s network settings
differs, depending on your operating system.
Windows 7 Users:
From the desktop, click the Start button, select Control Panel.
Under Network and Sharing Center, select Change adapter
settings from the menu on the left side of the screen.
Right-click on the Local Area Connection icon and select
Properties.
In the Local Area Connection Properties dialog box,
highlight Internet Protocol Version 4 (TCP/Ipv4) and click
the Properties button.
Select Use the following IP address and enter 192.168.1.100
and 255.255.255.0 as the IP address and Subnet mask,
respectively.
Click OK twice.
Re-enter 192.168.1.1 in your Web browser’s address bar.
Windows Vista Users:
From the desktop, click the Start button, select Control Panel,
and then double-click Network and Sharing Center.
In the Network and Sharing Center window, under Tasks,
select Manage Network Connections.
In the Network Connections window, double-click the Local
Area Connection option.
In the Local Area Connection Status dialog box, click the
Properties button.
In the Local Area Connection Properties dialog box,
highlight Internet Protocol Version 4 (TCP/Ipv4) and click
the Properties button.
Select Use the following IP address and enter 192.168.1.100
and 255.255.255.0 as the IP address and Subnet mask,
respectively.
Click OK, then click Close.
Re-enter 192.168.1.1 in your Web browser’s address bar.
Appendix D: TCP/IP Network Settings
95
Windows XP
Open the Internet Protocol (TCP/IP) Properties dialog box.
From the desktop, click the Start button, point to Control
Panel, and then click Network and Internet
Connections.
Click Network Connections.
Right-click the Local Area Connection icon, and select
Properties.
Select your NIC card’s TCP/IP entry (it should include
“TCP/IP” in it, but not “AOL,” “Dial-up,” or “Adapter”)
and click the Properties button.
Ensure the following is selected, depending on whether you are
using dynamic (DHCP) or static IP addressing:
¾ If you are using DHCP (most users): Ensure that Obtain
an IP address automatically is selected and that either
Obtain a DNS server address automatically or Enable
DNS is selected. All fields should be blank.
¾ If you are using a static IP address: Ensure that Use the
following IP address and Use the following DNS server
addresses are selected and that the correct IP address,
Subnet mask, Default gateway, and Preferred DNS server
values appear.
Windows 2000
Open the Internet Protocol (TCP/IP) Properties dialog box.
From the desktop, click the Start button, point to
Settings, then Network and Dial-up Connections.
Right-click the Local Area Connection icon, and select
Properties.
Appendix D: TCP/IP Network Settings
X7N User Manual
c
Select your NIC card’s TCP/IP entry (it should include
“TCP/IP” in it, but not “AOL,” “Dial-up,” or “Adapter”)
and click the Properties button.
Ensure the following is selected, depending on whether you are
using dynamic (DHCP) or static IP addressing:
¾ If you are using DHCP (most users): Ensure that Obtain
an IP address automatically is selected and that either
Obtain a DNS server address automatically or Enable
DNS is selected. All fields should be blank.
¾ If you are using a static IP address: Ensure that Use the
following IP address and Use the following DNS server
addresses are selected and that the correct IP address,
Subnet mask, Default gateway, and Preferred DNS server
values appear.
Windows 98/Me
Open the Internet Protocol (TCP/IP) Properties dialog box.
From the desktop, click the Start button, point to
Settings, then Control Panel.
Double-click the Network icon to display the Network
dialog box.
Select your NIC card’s TCP/IP entry (it should include
“TCP/IP” in it, but not “AOL,” “Dial-up,” or “Adapter”)
and click the Properties button and then click OK
Ensure the following is selected, depending on whether you are
using dynamic (DHCP) or static IP addressing:
¾ If you are using DHCP (most users): Ensure that Obtain
an IP address automatically is selected and that either
Obtain a DNS server address automatically or Enable
DNS is selected. All fields should be blank.
¾ If you are using a static IP address: Ensure that
Specify an IP address is selected and that the correct IP
Address and Subnet Mask values appear. On the DNS
Configuration tab, ensure that Enable DNS is selected
and that something appears in the Host box. (If not, enter
any name, word, or combination of letters and numbers.)
Appendix D: TCP/IP Network Settings
97
Ensure that the DNS Server Search Order box contains
192.168.1.1
Appendix D: TCP/IP Network Settings
X7N User Manual
Appendix E: Configuring
Your Web Browser
Important!
This section is for Windows computers only. If you are using a
Mac computer, your browser is already configured properly.
However, you must ensure that your computer’s TCP/IP settings
are configured properly. See Macintosh TCP/IP Settings on
page 93 for instructions on how to do this.
When using a Windows computer, the software that you use to
make an Internet connection must be set for a network
connection, not a dial-up connection. This configuration should
have been done automatically when you installed the software.
If you find that you need to configure your Web browser, this
section includes instructions for recent versions of two popular
Web browsers: Internet Explorer Version 5.0 (or later) and Mozilla
Firefox 3.x. The configuration is done on the same computer on
which you installed the X7N software.
Depending on the browser you have on your Windows computer,
follow the corresponding instructions in this section.
Tip:
If you are using an earlier version of one of these browsers, the
configuration may be slightly different from below. In those
cases—or if you are using another browser altogether—configure
the browser to use a network connection (this might be called a
“Local Area Network” or “broadband” connection).
Appendix E: Configuring Your Web Browser
99
Configuring Internet Explorer Version 8.0
The following instructions are for Internet Explorer Version 8.0.
(If you do not have this version, you can get a free upgrade from
Microsoft Corp. If you are not sure what version you have, open
Internet Explorer and from the Help menu, choose About
Internet Explorer. The version number is directly below the
Microsoft Internet Explorer logo. You can ignore all the numbers
after the period following the first digit.)
Note: If you are using Windows 7, you do not need to do
anything since it will be configured automatically.
Internet Explorer can be configured to use a specific connection
but by default will use the correct default active connection.
However, if you want to manually setup a different connection:
On the desktop, double-click the Internet Explorer icon.
Tip:
If you cannot access Internet Explorer in this way, open your
computer’s Control Panel (click the Start button and then,
depending on your computer, either click Control Panel, or
click Settings and then Control Panel). In the Control Panel,
double-click the Internet Options icon. If this icon does not
appear, double-click the Network and Internet Options icon
and then double-click the Internet Options icon.
Once open, select Tools Æ Internet Options and then click
on the Connections tab.
Select Setup to setup an Internet connection.
If the wired Ethernet is correctly setup then a popup message
“You Are Already Connected To The Internet” will display.
You do not need to proceed further. The browser is already
setup successfully using the wired Ethernet connection.
If you select Set up a new connection anyway you will be
displayed options to setup a different connection type that
your PC supports (PPPoE connection and a Wireless
connection). Since the X7N device is not wireless and will not
Appendix E: Configuring Your Web Browser
X7N User Manual
work with a PPPoE connection type by default then you do
not need to setup either of these and can use the existing wired
connection successfully.
Configuring Internet Explorer Version 7.0
The following instructions are for Internet Explorer Version 8.0.
(If you are not sure what version you have, open Internet Explorer
and from the Help menu, choose About Internet Explorer. The
version number is directly below the Microsoft Internet Explorer
logo. You can ignore all the numbers after the period following the
first digit.)
Note: If you are using Windows 7, you do not need to do
anything since it will be configured automatically.
Internet Explorer can be configured to use a specific connection
but by default will use the correct default active connection.
However, if you want to manually setup a different connection:
On the desktop, double-click the Internet Explorer icon.
Tip:
If you cannot access Internet Explorer in this way, open your
computer’s Control Panel (click the Start button and then,
depending on your computer, either click Control Panel, or
click Settings and then Control Panel). In the Control Panel,
double-click the Internet Options icon. If this icon does not
appear, double-click the Network and Internet Options icon
and then double-click the Internet Options icon.
Once open, select Tools Æ Internet Options and then click
on the Connections tab.
Select Setup to setup an Internet connection which will open
the New Connection Wizard screen.
Click Next.
Select the type of connection desired. Select Connect to the
Internet. to access the modem's HTTP Server. Click Next.
Select Set up my connection manually. Click Next.
Appendix E: Configuring Your Web Browser
101
7
Select Connect using a broadband connection that is
always on. Click Next.
Select Finish.
Configuring Internet Explorer 5.0 or 6.0
The following instructions are for Internet Explorer Version 5.0
and 6.0. (If you are not sure what version you have, open Internet
Explorer and from the Help menu, choose About Internet
Explorer. The version number is directly below the Microsoft
Internet Explorer logo. You can ignore all the numbers after the
period following the first digit.)
On the desktop, right-click the Internet Explorer icon, and
select Properties.
Tip:
If you cannot access Internet Explorer in this way, open your
computer’s Control Panel (click the Start button and then,
depending on your computer, either click Control Panel, or
click Settings and then Control Panel). In the Control Panel,
double-click the Internet Options icon. If this icon does not
appear, double-click the Network and Internet Options icon
and then double-click the Internet Options icon.
On the Internet Properties dialog box, select the
Connections tab, then click the Setup button.
Appendix E: Configuring Your Web Browser
X7N User Manual
3
The setup process will proceed differently, depending on your
operating system. The following table details the process for
your Windows computer.
Note: If you are using Windows 7, you do not need to do
anything since it will be configured automatically.
Windows XP
Windows 98/Me/2000
a.
a.
b.
c.
d.
e.
On the Welcome to the
New Connection Wizard
dialog box, click Next.
(If you see a Location
Information dialog box,
click Cancel and then
when asked if you are sure
you want to cancel, click
Yes to return to the
Welcome dialog box.)
On the Network
Connection Type dialog
box, select Connect to
the Internet, then click
Next.
On the Getting Ready
dialog box, select Set up
my connection manually,
then click Next.
On the Internet
Connection dialog box,
select Connect using a
broadband connection
that is always on, then
click Next.
On the Completing the
New Connection Wizard
dialog box, click Finish.
b.
c.
d.
e.
On the Internet
Connection Wizard
dialog box, select I want
to set up my Internet
connection manually, or
I want to connect
through a local area
network (LAN), then click
Next.
On the Setting up your
Internet connection
dialog box, select I
connect through a local
area network (LAN), then
click Next.
On the Local area
network Internet
configuration dialog box,
uncheck the Automatic
discovery of proxy
server check box, then
click Next.
On the Set Up Your
Internet Mail Account
dialog box select No, then
click Next.
On the Completing the
New Connection Wizard
dialog box, uncheck the
To connect to the
Internet immediately,
select this box… check
box (if it appears) and click
Finish.
If you accessed Internet Explorer’s settings from the Control
Panel (as explained in the “Tip” following step 1), the Control
Panel window will still be open. Close it before continuing.
Appendix E: Configuring Your Web Browser
103
Configuring Mozilla Firefox
No setup is necessary since Mozilla Firefox will use the active
connection. Unlike IE, Firefox cannot be configured to use a
specific connection type; it will use whatever is available and active
at the time.
Configuring Google Chrome
No setup is necessary since Google Chrome will use the active
connection. Unlike IE, Google Chrome cannot be configured to
use a specific connection type; it will use whatever is available and
active at the time.
Appendix E: Configuring Your Web Browser
X7N User Manual
Appendix F: Wireless
Channels by Country
For most countries channels 1-13 are normal for private wireless
networks. The following table shows countries known to use
channels other than 1-13 for private wireless networks.
Country
France
Israel
Japan
Taiwan
USA
Channels
10-13
4-9
1-13
14 (802.11b only)
1-11
1-11
Appendix F: Wireless Channels by Country
Appendix G: Getting
Help
Zoom has many Technical Support services available to its
customers.
• To Register Your Product Or Get Assistance
We can support you best if you register your product at
www.zoomtel.com/register
We have many ways to assist you, and you can see them at
www.zoomtel.com/techsupport
From here, you can send email to our technical support experts
and/or do a smart search through our intelligent database by
using SmartFacts™.
Tip:
From time to time, Zoom may release improved firmware.
This is also available at www.zoomtel.com, along with
upgrade instructions. We recommend that you check our Web
site periodically for updates.
You can reach Technical Support by calling these numbers:
In the United States, call (617) 753-0961.
In the UK, call
London: +44 2033180660 or
Manchester: +44 1618840074
• Some retailers of Zoom products provide support or can
recommend a convenient support center.
Appendix G: Getting Help
Appendix H: Regulatory
Information
Declaration of Conformity
Declaración de conformidad
Manufacturer/Fabricante
Zoom Telephonics, Inc.
207 South Street
Boston, MA 02111 USA
617-423-1072
www.zoomtel.com
Brand/Marca
Zoom ADSL Modem/Router w/ Wireless-N
Type/Tipo
Series 1093 Model 5790XY (where X=A,B,C,D,E,F or nothing
and Y=G,H,J,K,L,M or nothing)
The manufacturer declares under sole responsibility that this equipment is
compliant to Directive 1999/5/EC via the following. This product is CE marked.
El fabricante declara bajo su exclusiva responsabilidad que este equipo satisface
la Directiva 1999/5/EC por medio de lo siguiente. Este producto tiene marca CE.
73/23/EEC – LVD
EN60950-1:2006 + A11:2009
+A1:2010, IEC60950-1:2005
89/336/EEC – EMC/EMF
EN301 489-1 V1.8.1:2008-04;
EN301 489-17 V2.1.1:2009-05;
EN55022:2006, Class B
1999/5/EC
EN300 328 v1.7.1:2006-10
Director, Hardware Engineering/
Director, Ingeniería de apoyo
Paul Prohodski
15 September 2011
1084/TF, Boston, MA, USA
Appendix H: Regulatory Information
Regulatory Notices for X7n Router with Wireless-N
(Regulatory Notices also apply to ADSL Splitter Model TD-1301)
U.S. FCC Part 68 Statement
This equipment complies with Part 68 of the FCC rules and the requirements adopted by the
ACTA. The unit bears a label on the back which contains among other information a
product identifier in the format US:AAAEQ##TXXXX. If requested, this number must be
provided to the telephone company.
This equipment uses the following standard jack types for network connection: RJ11C.
This equipment contains an FCC compliant modular jack. It is designed to be connected to
the telephone network or premises wiring using compatible modular plugs and cabling
which comply with the requirements of FCC Part 68 rules.
The Ringer Equivalence Number, or REN, is used to determine the number of devices
which may be connected to the telephone line. An excessive REN may cause the equipment
to not ring in response to an incoming call. In most areas, the sum of the RENs of all
equipment on a line should not exceed five (5.0).
In the unlikely event that this equipment causes harm to the telephone network, the
telephone company can temporarily disconnect your service. The telephone company will try
to warn you in advance of any such disconnection, but if advance notice isn't practical, it
may disconnect the service first and notify you as soon as possible afterwards. In the event
such a disconnection is deemed necessary, you will be advised of your right to file a
complaint with the FCC.
From time to time, the telephone company may make changes in its facilities, equipment, or
operations which could affect the operation of this equipment. If this occurs, the telephone
company is required to provide you with advance notice so you can make the modifications
necessary to obtain uninterrupted service.
There are no user serviceable components within this equipment. See Warranty flyer for
repair or warranty information.
It shall be unlawful for any person within the United States to use a computer or other
electronic device to send any message via a telephone facsimile unless such message clearly
contains, in a margin at the top or bottom of each transmitted page or on the first page of
the transmission, the date and time it is sent and an identification of the business, other
entity, or individual sending the message and the telephone number of the sending machine
or of such business, other entity, or individual. The telephone number provided may not be
a 900 number or any other number for which charges exceed local or long distance
transmission charges. Telephone facsimile machines manufactured on and after December
20, 1992, must clearly mark such identifying information on each transmitted message.
Facsimile modem boards manufactured on and after December 13, 1995, must comply with
the requirements of this section.
This equipment cannot be used on public coin phone service provided by the telephone
company.
If trouble is experienced with this equipment, for repair or warranty information, please
contact: Zoom Telephonics, Inc. 207 South Street, Boston, MA 02111, USA, (617) 753-0961
If the equipment is causing harm to the telephone network, the telephone company may
request that you disconnect the equipment until the problem is resolved.
Connection to Party Line Service is subject to state tariffs. Contact your state public utility
commission, public service commission, or corporation commission for more information.
If your home has specially wired alarm equipment connected to the telephone line, ensure
the installation of this equipment does not disable your alarm equipment. If you have
questions about what will disable alarm equipment, consult your telephone company or a
qualified installer.
Appendix H: Regulatory Information
WHEN PROGRAMMING EMERGENCY NUMBERS AND(OR) MAKING TEST
CALLS TO EMERGENCY NUMBERS:
1) Remain on the line and briefly explain to the dispatcher the reason for the call.
2) Perform such activities in the off-peak hours, such as early morning or late evenings.
U.S. FCC Part 15 Emissions Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible
for compliance could void the user's authority to operate this equipment.
Operations in the 5.15-5.25GHz band are restricted to indoor usage only.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
IMPORTANT NOTE:
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance
20cm between the radiator & your body.
This transmitter must not be co-located or operating in conjunction with any other antenna
or transmitter.
Note: The country code selection is for non-US model only and is not available to all US
model. Per FCC regulation, all WiFi product marketed in US must fixed to US operation
channels only.
Industry Canada Emissions Statement
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing
Equipment Regulations.
Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le
matériel brouilleur du Canada.
This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2) this
Appendix H: Regulatory Information
device must accept any interference received, including interference that may cause
undesired operation.
Ce dispositif est conforme à la norme CNR-210 d'Industrie Canada applicable aux appareils
radio exempts de licence. Son fonctionnement est sujet aux deux conditions suivantes: (1) le
dispositif ne doit pas produire de brouillage préjudiciable, et (2) ce dispositif doit accepter
tout brouillage reçu, y compris un brouillage susceptible de provoquer un fonctionnement
indésirable.
IMPORTANT NOTE: (For mobile device use)
Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance
20cm between the radiator & your body.
NOTE IMPORTANTE: (Pour l'utilisation de dispositifs mobiles)
Déclaration d'exposition aux radiations:
Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un
environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum
de 20 cm de distance entre la source de rayonnement et votre corps.
(The user manual of transmitter devices equipped with detachable antennas shall contain the
following information in a conspicuous location: )
This device has been designed to operate with an antenna having a maximum gain of 5.1 dB.
Antenna having a higher gain is strictly prohibited per regulations of Industry Canada. The
required antenna impedance is 50 ohms.
Under Industry Canada regulations, this radio transmitter may only operate using an antenna
of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To
reduce potential radio interference to other users, the antenna type and its gain should be so
chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that
necessary for successful communication.
This radio transmitter (IC: 1535A-1093 / Model: 5790) has been approved by Industry
Canada to operate with the antenna types listed below with the maximum permissible gain
and required antenna impedance for each antenna type indicated. Antenna types not
included in this list, having a gain greater than the maximum gain indicated for that type, are
strictly prohibited for use with this device.
(Le manuel d'utilisation de dispositifs émetteurs équipés d'antennes amovibles doit contenir
les informations suivantes dans un endroit bien en vue:)
Ce dispositif a été conçu pour fonctionner avec une antenne ayant un gain maximal de dB 5.
Une antenne à gain plus élevé est strictement interdite par les règlements d'Industrie Canada.
L'impédance d'antenne requise est de 50 ohms.
Conformément à la réglementation d'Industrie Canada, le présent émetteur radio
peutfonctionner avec une antenne d'un type et d'un gain maximal (ou inférieur) approuvé
pourl'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage
radioélectriqueà l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain
de sorte que lapuissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité
nécessaire àl'établissement d'une communication satisfaisante.
Le présent émetteur radio (IC: 1535A-1093 / Modèle: 5790) a été approuvé par Industrie
Canada pour fonctionner avec les types d'antenne énumérés ci-dessous et ayant un gain
admissible maximal et l'impédance requise pour chaque type d'antenne. Les types d'antenne
Appendix H: Regulatory Information
non inclus dans cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont
strictement interdits pour l'exploitation de l'émetteur.
Industry Canada CS03 Statement
Notice: The Industry Canada label identifies certified equipment. This certification means
that the equipment meets telecommunications network protective, operational and safety
requirements as prescribed in the appropriate Terminal Equipment Technical Requirements
document(s). The Department does not guarantee the equipment will operate to the user's
satisfaction.
Before installing the equipment, users should ensure that it is permissible to be connected to
the facilities of the local telecommunications company. The equipment must also be installed
using an acceptable method of concern. The customer should be aware that compliance with
the above conditions may not prevent degradation of service in some situations.
Repairs to certified equipment should be coordinated by a representative designated by the
supplier. Any repairs or alterations made by the user to this equipment, or equipment
malfunctions, may give the telecommunications company cause to request the user to
disconnect the equipment.
Users should ensure for their own protection that the electrical ground connections of the
power utility, telephone lines and internal metallic water pipe system, if present, are
connected together. This precaution may be particularly important in rural areas. Caution:
Users should not attempt to make such connections themselves, but should contact the
appropriate electric inspection authority, or electrician, as appropriate.
''NOTICE: This equipment meets the applicable Industry Canada Terminal Equipment
Technical Specifications. This is confirmed by the registration number. The abbreviation, IC,
before the registration number signifies that registration was performed based on a
Declaration of Conformity indicating that Industry Canada technical specifications were met.
It does not imply that Industry Canada approved the equipment.”
« AVIS : Le présent matériel est conforme aux spécifications techniques d’Industrie Canada
applicables au matériel terminal. Cette conformité est confirmée par le numéro
d'enregistrement. Le sigle IC, placé devant le numéro d'enregistrement, signifie que
l’enregistrement s’est effectué conformément à une déclaration de conformité et indique que
les spécifications techniques d'Industrie Canada ont été respectées. Il n’implique pas
qu’Industrie Canada a approuvé le matériel. »
''NOTICE: The Ringer Equivalence Number (REN) for this terminal equipment is 0.1. The
REN assigned to each terminal equipment provides an indication of the maximum number
of terminals allowed to be connected to a telephone interface. The termination on an
interface may consist of any combination of devices subject only to the requirement that the
sum of the Ringer Equivalence Numbers of all the devices does not exceed five.''
« AVIS : L'indice d'équivalence de la sonnerie (IES) du présent matériel est de 0,1. L'IES
assigné à chaque dispositif terminal indique le nombre maximal de terminaux qui peuvent
être raccordés à une interface téléphonique. La terminaison d'une interface peut consister en
une combinaison quelconque de dispositifs, à la seule condition que la somme d'indices
d'équivalence de la sonnerie de tous les dispositifs n'excède pas 5. »
Appendix H: Regulatory Information
European Declaration of Conformity
The manufacturer declares under sole responsibility that this equipment is compliant to
Directive 1999/5/EC (R&TTE Directive) via the following. This product is CE Marked.
Directive
Standard
Test Report
73/23/EEC-Low
Voltage
EN60950-1:2006 + A11:2009,
IEC60950-1:2005
Electrical safety
89/336/EEC-EMC
EN 301 489-1 v1.6.1 :2005-09; EN
301 489-17 1.2.1 :2002;
EN 55022 : 2006, Class B
EMC-immunity
EMC-emissions
Electrostatic Discharge Statement
The unit may require resetting after a severe electrostatic discharge event.
Note: If you do not use the supplied phone cord, use an equivalent of minimum AWG 26
line cord.
CAUTION: To reduce the risk of fire, use only No. 26 AWG or larger UL Listed or CSA
Certified Telecommunication Line Cord
Europe – EU Declaration of Conformity
This device complies with the essential requirements of the R&TTE Directive 1999/5/EC.
The following test methods have been applied in order to prove presumption of conformity
with the essential requirements of the R&TTE Directive 1999/5/EC:
EN 60950-1: 2006
Safety of Information Technology Equipment
EN50385：2002
Assessment of electronic and electrical equipment related to human exposure
restrictions for electromagnetic fields
EN 300 328 V1.7.1: (2006-10)
Electromagnetic compatibility and Radio spectrum Matters (ERM); Wideband
Transmission systems; Data transmission equipment operating in the 2,4 GHz ISM
band and using spread spectrum modulation techniques; Harmonized EN covering
essential requirements under article 3.2 of the R&TTE Directive
EN 301 489-1 V1.8.1: (2008-04)
Electromagnetic compatibility and Radio Spectrum Matters (ERM); ElectroMagnetic
Compatibility (EMC) standard for radio equipment and services; Part 1: Common
technical requirements
EN 301 489-17 V1.3.2 (2008-04)
Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic
Compatibility (EMC) standard for radio equipment and services; Part 17: Specific
conditions for 2,4 GHz wideband transmission systems and 5 GHz high performance
RLAN equipment
This device is a 2.4 GHz wideband transmission system (transceiver), intended for use in all
EU member states and EFTA countries, except in France and Italy where restrictive use
applies.
In Italy the end-user should apply for a license at the national spectrum authorities in order
to obtain authorization to use the device for setting up outdoor radio links and/or for
supplying public access to telecommunications and/or network services.
Appendix H: Regulatory Information
This device may not be used for setting up outdoor radio links in France and in some areas
the RF output power may be limited to 10 mW EIRP in the frequency range of 2454 –
2483.5 MHz. For detailed information the end-user should contact the national spectrum
authority in France.
Česky
[Czech]
[Jméno výrobce] tímto prohlašuje, že tento [typ zařízení] je ve shodě se
základními požadavky a dalšími příslušnými ustanoveními směrnice
1999/5/ES.
Dansk
[Danish]
Undertegnede [fabrikantens navn] erklærer herved, at følgende udstyr
[udstyrets typebetegnelse] overholder de væsentlige krav og øvrige
relevante krav i direktiv 1999/5/EF.
Deutsch
[German]
Hiermit erklärt [Name des Herstellers], dass sich das Gerät [Gerätetyp] in
Übereinstimmung mit den grundlegenden Anforderungen und den
übrigen einschlägigen Bestimmungen der Richtlinie 1999/5/EG
befindet.
Eesti
[Estonian]
Käesolevaga kinnitab [tootja nimi = name of manufacturer] seadme
[seadme tüüp = type of equipment] vastavust direktiivi 1999/5/EÜ
põhinõuetele ja nimetatud direktiivist tulenevatele teistele
asjakohastele sätetele.
English
Hereby, [name of manufacturer], declares that this [type of equipment] is in
compliance with the essential requirements and other relevant
provisions of Directive 1999/5/EC.
Español
[Spanish]
Por medio de la presente [nombre del fabricante] declara que el [clase de
equipo] cumple con los requisitos esenciales y cualesquiera otras
disposiciones aplicables o exigibles de la Directiva 1999/5/CE.
Ελληνική
[Greek]
ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ [name of manufacturer] ΔΗΛΩΝΕΙ ΟΤΙ [type of
equipment] ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩΔΕΙΣ
ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ
ΤΗΣ ΟΔΗΓΙΑΣ 1999/5/ΕΚ.
Français
[French]
Par la présente [nom du fabricant] déclare que l’appareil [type d’appareil]
est conforme aux exigences essentielles et aux autres dispositions
pertinentes de la directive 1999/5/CE.
Italiano
[Italian]
Con la presente [nome del costruttore] dichiara che questo [tipo di
apparecchio] è conforme ai requisiti essenziali ed alle altre disposizioni
pertinenti stabilite dalla direttiva 1999/5/CE.
Latviski
Ar šo [name of manufacturer / izgatavotāja nosaukums] deklarē, ka [type of
Appendix H: Regulatory Information
[Latvian]
equipment / iekārtas tips] atbilst Direktīvas 1999/5/EK būtiskajām
prasībām un citiem ar to saistītajiem noteikumiem.
Lietuvių
Šiuo [manufacturer name] deklaruoja, kad šis [equipment type] atitinka
[Lithuanian]
esminius reikalavimus ir kitas 1999/5/EB Direktyvos nuostatas.
Nederlands
[Dutch]
Hierbij verklaart [naam van de fabrikant] dat het toestel [type van toestel]
in overeenstemming is met de essentiële eisen en de andere relevante
bepalingen van richtlijn 1999/5/EG.
Malti
[Maltese]
Hawnhekk, [isem tal-manifattur], jiddikjara li dan [il-mudel tal-prodott]
jikkonforma mal-ħtiġijiet essenzjali u ma provvedimenti oħrajn
relevanti li hemm fid-Dirrettiva 1999/5/EC.
Magyar
[Hungarian]
Alulírott, [gyártó neve] nyilatkozom, hogy a [... típus] megfelel a
vonatkozó alapvetõ követelményeknek és az 1999/5/EC irányelv
egyéb elõírásainak.
Polski
[Polish]
Niniejszym [nazwa producenta] oświadcza, że [nazwa wyrobu] jest
zgodny z zasadniczymi wymogami oraz pozostałymi stosownymi
postanowieniami Dyrektywy 1999/5/EC.
Português
[Portuguese]
[Nome do fabricante] declara que este [tipo de equipamento] está conforme
com os requisitos essenciais e outras disposições da Directiva
1999/5/CE.
Slovensko
[Slovenian]
Slovensky
[Slovak]
Suomi
[Finnish]
[Ime proizvajalca] izjavlja, da je ta [tip opreme] v skladu z bistvenimi
zahtevami in ostalimi relevantnimi določili direktive 1999/5/ES.
[Meno výrobcu] týmto vyhlasuje, že [typ zariadenia] spĺňa základné
požiadavky a všetky príslušné ustanovenia Smernice 1999/5/ES.
[Valmistaja = manufacturer] vakuuttaa täten että [type of equipment =
laitteen tyyppimerkintä] tyyppinen laite on direktiivin 1999/5/EY
oleellisten vaatimusten ja sitä koskevien direktiivin muiden ehtojen
mukainen.
Svenska
[Swedish]
Härmed intygar [företag] att denna [utrustningstyp] står I
överensstämmelse med de väsentliga egenskapskrav och övriga
relevanta bestämmelser som framgår av direktiv 1999/5/EG.
Appendix H: Regulatory Information
Compliance Model Identification
FCC 15C，
FCC 15B，
FCC 68
Model name
Product name
Zoom ADSL
MODEM/Router
w/ Wireless-N
SERIES 1093 MODEL
5790XY WHERE
X=A,B,C,D,E,F OR
NOTHING AND
Y=G,H,J,K,L,M OR
NOTHING
Series 1093 Model 5790
Zoom ADSL
MODEM/Router
w/ Wireless-N
Zoom ADSL
Series 1093
CE0678！
MODEM/Router
w/ Wireless-N
FCC Part 68 ID
BDNDL01B1093
IC ，ICES003，CS-03
FCC ID
IC ID
2581-A
BDN1093WL
1535A-1093
27659
Appendix H: Regulatory Information
©2011

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Encryption                      : Standard V2.3 (128-bit)
User Access                     : Print, Extract, Print high-res
XMP Toolkit                     : 3.1-701
Producer                        : Acrobat Distiller 7.0 (Windows)
Create Date                     : 2011:09:17 10:21:40+08:00
Modify Date                     : 2011:09:28 13:16:20+08:00
Metadata Date                   : 2011:09:28 13:16:20+08:00
Format                          : application/pdf
Title                           : untitled
Document ID                     : uuid:08b215d9-d580-492e-aecc-88b07336bf9b
Instance ID                     : uuid:b0ac231e-b883-4426-b69a-a390199747e0
Page Count                      : 115

EXIF Metadata provided by EXIF.tools