ZyXEL Communications C3000Z WiFi-N VDSL2 4-port Combo WAN CPE User Manual

ZyXEL Communications Corporation WiFi-N VDSL2 4-port Combo WAN CPE

User Manual.pdf

Quick Start Guidewww.zyxel.comC3000ZWiFi-N/AC 2.4G 3x3 /5G 4X4 VDSL2 4-port Bonding Combo WAN IADVersion CZD001-4.16.002.0Edition 1, 04/2017Default Login DetailsLAN IP Address http://192.168.0.1User Name adminPassword Check the device labelCopyright © 2017 ZYXEL Communications CorporationQuick Start Guide
2Device PanelsPOWERDSLINTERNETETHERNETUSB SLOTPOWERRESETDSL PORTUSBETHERNET 1-4WIFI 2.4GWAN/LANLAN/WAN PORTS 1-4WPS BUTTONPORTWIFI 5G
3OverviewThe Device is a VDSL2 bonding integrated access device (IAD) with a four-port built-in Ethernet switch and IEEE 802.11ac wireless. The Device allows wired and wireless clients to safely access the Internet. Additionally, the Device includes a Gigabit Ethernet LAN port that can also serve as a WAN connection to support a dual WAN function. The USB port allows you to connect a USB memory stick or USB hard drive for storing or sharing files through the network.RequirementsMake sure you have the following things before you start.• Internet access - account information provided by your ISP, such as user name, password, and so on.• Internet Explorer 8.0 and later versions, with JavaScript enabled, or Mozilla Firefox 14 and later versions.
44Hardware Connections1234
51. Use a telephone cable to connect your Device’s DSL port to a telephone jack (or the DSL or modem jack on a splitter if you have one).2. ETHERNET: Use an Ethernet cable to connect a computer to a LAN port for initial configuration and/or Internet access.3. USB: You can connect a USB memory stick or a USB hard drive for file sharing. The Device automatically detects the USB device. Alternatively, use a USB cable (not provided) to connect a USB printer to this port.4. POWER: Use the provided power adaptor to connect the POWER socket to an appropriate power source. Make sure the power at the outlet is on. Look at the lights on the front panel.•The POWER light blinks while your Device starts up and then stays solid green once it is ready.•The DSL lights are solid green after your Device has a DSL connection. •The INTERNET light turns on when the Device is able to access the Internet and blinks when the Device is sending or receiving data. •The WAN/LAN light is on if the WAN/LAN port is properly connected and blinks when there is traffic.• Each ETHERNET light is on if the corresponding LAN port is properly connected and blinks when there is traffic.•The USB light turns on when there is a USB printer or memory device is connected to the Device and blinks when transmitting data.•The WiFi 2.4G light is green when the wireless LAN is ready and blinks when there is traffic. •The WiFi 5G light is green when the wireless LAN is ready and blinks when there is traffic.•The WPS light is green when WPS is enabled and blinks amber while WPS is in process.If the lights do not come on, check your connections and inspect your cables for damage. If the lights are still off, contact technical support.
66Internet Connection SetupYour Device can automatically detect and configure your Internet connection once the hardware is connected properly. Automatic Connection1. Open your web browser to a website. Wait while your Device tries to detect your DSL connection to your ISP. This may take a few minutes.2. After it detects the connection, the DSL lights show amber on your Device and the INTERNET light comes on when the Internet is ready for you to use. If you have a PPPoE connection, you will have to enter the user name and password provided by your ISP.3. Go to Set Up a Wireless Network if you wish to configure your wireless settings.4. If the automatic connection is not successful, check your connections and restart the Device. Also, make sure you have entered the user name and password correctly. If you still cannot access the Internet, follow the steps in the next section to manually configure the Internet connection.Manual ConnectionYou can also manually log into the Device’s Web Configurator and configure the Internet connection.1. In your browser, if the Device does not automatically re-direct you to the login screen, go to http://192.168.0.1.
72. Enter the default user name admin and password (see the Device’s label). Click Apply.If the login screen does not open, make sure you allow web browser pop-up windows, JavaScripts and Java permissions. Your computer should be also set to get an IP address automatically from a DHCP server. 3. The main screen appears. Click Quick Setup to configure the Device’s Internet access.
884. Enter the user name and password provided by your ISP. Click Apply to finish the configuration. 5. The DSL lights are green on your Device and the INTERNET light comes on when the Internet is ready for you to use. If you still cannot access the Internet, contact your ISP. Set Up a Wireless NetworkYou can set up a wireless network using the following methods:Using Wireless Protected Setup (WPS)Press the WPS button on the Device’s front panel for more than 5 seconds to turn the WPS function on.
9Follow these steps to add a WPS-enabled device to the wireless network using the WPS button.Set Up a Wireless Network ManuallyThe wireless LAN on your Device is enabled by default. To add a wireless client to the network, use the settings found on the bottom panel of your Device.Configure wireless devices that you want to connect to the wireless network to use the same wireless settings as the Device.The default wireless settings vary for each Device. Refer to the label of your Device and use the provided information. Place the devices you want to connect near one another.Press the WPS button on the Device.Press the WPS button on a compatible device within 2 minutes of pressing the button on the Device.The WPS light on the Device blinks amber when connection is in progress and is solid green when connected.WPS123
1010Wall MountingThe following are dimensions of a screw anchor and M4 tap screw used for wall mounting. All measurements are in millimeters (mm). 1. Locate a high position on a wall that is free of obstructions. Use a sturdy wall. 2. For a concrete or brick wall find a drill bit with the same diameter as the screw anchors. If you do not need the screw anchors, find a drill bit slightly smaller in diameter than the included screws.3. Drill the two screw holes in the wall. Make sure the distance between the centers of the holes is the same as the wall-mount holes. Be careful to avoid damaging pipes or cables located inside the wall when drilling holes for the screws.
114. Use a hammer to tap the screw anchors into the holes.5. Insert and slowly screw the screws into the anchors (or the holes if you are not using anchors). Make sure the screws are snugly fastened to the wall. They need to hold the weight of the Device with the connection cables. Do not screw the screws all the way into the wall. Leave a small gap of about 0.5 cm between the heads of the screws and the wall. 94.5mm
12126. Align the holes on the back of the Device with the screws on the wall. Hang the Device on the screws.Federal Communications Commission (FCC):This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) This device may not cause harmful interference, and(2) This device must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio
13frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.• Consult the dealer or an experienced radio/TV technician for help. CautionChanges or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible.This device and it's antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter except in accordance with FCC multi-transmitter product procedures.IMPORTANT NOTE:Radiation Exposure Statement:This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 40 cm between the radiator and your body.FCC REQUIREMENTS:This equipment complies with TIA-968-B of FCC Rules. On the bass unit of this equipment is a label that contains, among other information, the FCC Registration Number and Ringer Equivalence Number (REN) for this equipment. IF REQUESTED, THIS INFORMATION MUST BE GIVEN TO THE TELEPHONE COMPANY.The REN is useful to determine the quantity of devices you may connect to your telephone line and still have all of those devices ring when your telephone number is called. In most, but not all areas, the sum of the REN of all devices connected to one line should not exceed five (5.0). To be certain of the number of devices you may connect to you line, as determined by the REN, you should contact your local telephone company to determine the maximum REN for your calling area.
1414If your equipment causes harm to the telephone network, the telephone company may discontinue your service temporarily. If possible, they will notify you in advance. But if advance notice is not practical, you will be notified as soon as possible. You will be informed of your right to file a complaint with the FCC. Your telephone company may make changes in it is facilities, equipment, operations or procedures that could affect the proper functioning of your equipment. If they do, you will be notified in advance to give you an opportunity to maintain uninterrupted telephone service.A Plug and jack used to connect this equipment to the premises wiring and telephone network must comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA. A compliant telephone cord and modular plug is provided with this product. It is designed to be connected to a compatible modular jack that is also compliant. See installation instructions for details.The telephone company may make changes in its facilities, equipment, operations or procedures that could affect the operation of the equipment. If this happens, the telephone company will provide advance notice in order for you to make necessary modifications to maintain uninterrupted service.This equipment could be repair by users, there is not any component can be removed or changed.Connection to party line service is subject to state tariffs. Contact the state public utility commission, public service commission or corporation commission for information.If you experience trouble with this telephone equipment, please contact the following address and phone number for information on obtaining service or repairs.The telephone company may ask that you disconnect this equipment from the network until the problem has been corrected or until you are sure that the equipment is not malfunctioning.This equipment may not be used on coin service provided by the telephone company. Connection to party lines is subject to state tariffs.COMPANY: ZYXEL Communications Inc.ADDRESS: 1130 N. Miller St., Anaheim CA, 92806 USATEL NO.: 714-6320882
15Safety Warnings• Do NOT use this product near water, for example, in a wet basement or near a swimming pool.• Do NOT expose your device to dampness, dust or corrosive liquids.• Do NOT store things on the device.• Do NOT install, use, or service this device during a thunderstorm. There is a remote risk of electric shock from lightning.• Connect ONLY suitable accessories to the device.• Do NOT open the device or unit. Opening or removing covers can expose you to dangerous high voltage points or other risks. ONLY qualified service personnel should service or disassemble this device. Please contact your vendor for further information.• Make sure to connect the cables to the correct ports.• Place connecting cables carefully so that no one will step on them or stumble over them.• Always disconnect all cables from this device before servicing or disassembling.• Use ONLY an appropriate power adaptor or cord for your device.• Connect the power adaptor or cord to the right supply voltage (for example, 110V AC in North America or 230V AC in Europe).• Do NOT allow anything to rest on the power adaptor or cord and do NOT place the product where anyone can walk on the power adaptor or cord.• Do NOT use the device if the power adaptor or cord is damaged as it might cause electrocution.• If the power adaptor or cord is damaged, remove it from the device and the power source.• Do NOT attempt to repair the power adaptor or cord. Contact your local vendor to order a new one.• Do not use the device outside, and make sure all the connections are indoors. There is a remote risk of electric shock from lightning. • Do NOT obstruct the device ventilation slots, as insufficient airflow may harm your device. • Use only No. 26 AWG (American Wire Gauge) or larger telecommunication line cord.• Antenna Warning! This device meets ETSI and FCC certification requirements when using the included antenna(s). Only use the included antenna(s). • The RJ-45 jacks are not used for telephone line connection.
1616Your product is marked with this symbol, which is known as the WEEE mark. WEEE stands for Waste Electronics and Electrical Equipment. It means that used electrical and electronic products should not be mixed with general waste. Used electrical and electronic equipment should be treated separately. EU Importer: ZYXEL Communications A/S | Generatorvej 8D, 2730 Herlev, Denmark | http://www.ZYXEL.dk US Importer: ZYXEL Communications, Inc | 1130 North Miller Street Anaheim, CA 92806-2001 | http://www.us.ZYXEL.com

Navigation menu