ZyXEL Communications C424G Indoor GPON HGU User Manual I88C424G

ZyXEL Communications Corporation Indoor GPON HGU I88C424G

I88C424G_User Manual

1/2 Copyright © 2016 ZyXEL Communications Corp. All Rights ReservedEU Importer: ZyXEL Communication A/S, Generatorvej 8D, 2860 Søborg, Denmark. http://www.zyxel.dkUS Importer: ZyXEL Communications, Inc 1130 North Miller Street Anaheim, CA 92806-2001. http://www.us.zyxel.comInternet SetupIP Address: 192.168.1.1Username: adminPassword: 1234Hardware ConnectionsConnect the power.WAN/GPONGREENPON not connected. Disconnect power and repeat hardware connection steps. PON connected and registered.4Connect a computer using an Ethernet cable. PON connected but not registered. 134VoIP registration failed.VoIP registration is complete. VoIP1VoIP setting is not properly configured. Go to the Web Configurator and configure VoIP settings.OFFGREENREDConnect a phone. 2Make sure the LEDs are on and check the GPON and VoIP LEDs. 123WAN/GPONWAN/GPONVoIP1VoIP1OFFGREEN (blinking)Quick Start GuideC424GDual-Band Wireless AC/N GPON HGU with 4-port GbE LAN
2/2Copyright © 2016 ZyXEL Communications Corp. All Rights ReservedSee the User's Guide at www.zyxel.com for more information.1Wall Mounting23WirelessWPSNo WPSWPS2Minutes(Within 2 Minutes)SSIDWireless key12(In 1 second...)(5 seconds)WiFi 2.4G(>5 seconds)1Press the WPS button until the WiFi 2.4G LED flashes in orange.2Press the WPS button on the client. 1The SSID and wireless key are on the device's bottom sticker. 2Find the device with its SSID. Enter wireless key to connect.12Advanced Setup > Layer2 Interface > GPON InterfaceORANGE
Federal Communications Commission (FCC) Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.  These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generate, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:    Reorient or relocate the receiving antenna.   Increase the separation between the equipment and receiver.   Connect the equipment into an outlet on a circuit different from that to which the receiver is    connected.   Consult the dealer or an experienced radio/TV technician for help.  This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)  This device may not cause harmful interference, and   (2)  This device must accept any interference received, including interference that may cause undesired operation.  FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.  RF exposure warning This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.  This  equipment  complies  with  FCC  radiation  exposure  limits  set  forth  for  an  uncontrolled environment.  This  equipment  must  be  installed  and  operated  in  accordance  with  provided instructions  and  the  antenna(s)  used  for  this  transmitter  must  be  installed  to  provide  a separation distance of at least 20cm from all persons and must not be collocated or operating in conjunction with any other antenna or transmitter.

Navigation menu