ZyXEL Communications NBG6816 Simultaneous Dual-Band Wireless AC2350 Ultra HD Media Router User Manual Book
ZyXEL Communications Corporation Simultaneous Dual-Band Wireless AC2350 Ultra HD Media Router Book
Contents
- 1. User Manual-1
- 2. User manual-2
User manual-2
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 2658767 |
| Application ID | cYL/ww9MKkH3roaU9pio/Q== |
| Document Description | User manual-2 |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 316.24kB (3953027 bits) |
| Date Submitted | 2015-06-25 00:00:00 |
| Date Available | 2015-12-24 00:00:00 |
| Creation Date | 2017-09-27 11:21:54 |
| Producing Software | GPL Ghostscript 9.18 |
| Document Lastmod | 2017-09-27 11:21:54 |
| Document Title | Book.book |
| Document Creator | FrameMaker 9.0 |
| Document Author: | ZT02102 |
A PPENDIX Pop-up Windows, JavaScript and Java Permissions In order to use the web configurator you need to allow: • Web browser pop-up windows from your device. • JavaScript (enabled by default). • Java permissions (enabled by default). Note: The screens used below belong to Internet Explorer version 6, 7 and 8. Screens for other Internet Explorer versions may vary. Internet Explorer Pop-up Blockers You may have to disable pop-up blocking to log into your device. Either disable pop-up blocking (enabled by default in Windows XP SP (Service Pack) 2) or allow pop-up blocking and create an exception for your device’s IP address. Disable Pop-up Blockers In Internet Explorer, select Tools, Pop- u p Block e r and then select Tur n Off Pop- up Block e r. Figure 101 Pop-up Blocker You can also check if pop-up blocking is disabled in the Pop- u p Block e r section in the Pr iva cy tab. In Internet Explorer, select Tools, I nt e r ne t Opt ions, Pr iva cy. Clear the Block pop- ups check box in the Pop- u p Block e r section of the screen. This disables any web pop-up blockers you may have enabled. ARMOR Z1 User’s Guide 157 Appendix A Pop-up Windows, JavaScript and Java Permissions Figure 102 Internet Options: Privacy Click Apply to save this setting. Enable Pop-up Blockers with Exceptions Alternatively, if you only want to allow pop-up windows from your device, see the following steps. In Internet Explorer, select Tools, I nt e r ne t Opt ions and then the Pr iva cy tab. Select Se t t ings…to open the Pop- up Block e r Se t t ings screen. ARMOR Z1 User’s Guide 158 Appendix A Pop-up Windows, JavaScript and Java Permissions Figure 103 Internet Options: Privacy Type the IP address of your device (the web page that you do not want to have blocked) with the prefix “http://”. For example, http://192.168.167.1. Click Add to move the IP address to the list of Allow e d sit e s. Figure 104 Pop-up Blocker Settings ARMOR Z1 User’s Guide 159 Appendix A Pop-up Windows, JavaScript and Java Permissions Click Close to return to the Pr iva cy screen. Click Apply to save this setting. JavaScript If pages of the web configurator do not display properly in Internet Explorer, check that JavaScript are allowed. In Internet Explorer, click Tools, I n t e r ne t Opt ion s and then the Se cur it y tab. Figure 105 Internet Options: Security Click the Cu st om Le ve l... button. Scroll down to Scr ipt ing. Under Act ive scr ipt ing make sure that Ena ble is selected (the default). Under Scr ipt ing of Ja va a pple t s make sure that Ena ble is selected (the default). Click OK to close the window. ARMOR Z1 User’s Guide 160 Appendix A Pop-up Windows, JavaScript and Java Permissions Figure 106 Security Settings - Java Scripting Java Permissions From Internet Explorer, click Tools, I nt e r ne t Opt ions and then the Se cu r it y tab. Click the Cu st om Le ve l... button. Scroll down to M icr osoft VM . Under Ja va pe r m issions make sure that a safety level is selected. Click OK to close the window. ARMOR Z1 User’s Guide 161 Appendix A Pop-up Windows, JavaScript and Java Permissions Figure 107 Security Settings - Java JAVA (Sun) From Internet Explorer, click Tools, I nt e r ne t Opt ions and then the Adva n ce d tab. Make sure that Use Ja va 2 for < a pple t > under Ja va ( Sun) is selected. Click OK to close the window. Figure 108 Java (Sun) ARMOR Z1 User’s Guide 162 Appendix A Pop-up Windows, JavaScript and Java Permissions Mozilla Firefox Mozilla Firefox 2.0 screens are used here. Screens for other versions may vary slightly. The steps below apply to Mozilla Firefox 3.0 as well. You can enable Java, Javascript and pop-ups in one screen. Click Tools, then click Opt ions in the screen that appears. Figure 109 Mozilla Firefox: TOOLS > Options Click Cont e n t to show the screen below. Select the check boxes as shown in the following screen. Figure 110 Mozilla Firefox Content Security ARMOR Z1 User’s Guide 163 Appendix A Pop-up Windows, JavaScript and Java Permissions Opera Opera 10 screens are used here. Screens for other versions may vary slightly. Allowing Pop-Ups From Opera, click Tools, then Pr e fe r e nce s. In the Ge n e r a l tab, go to Ch oose h ow you pr e fe r t o h a n dle pop- ups and select Ope n a ll pop- ups. Figure 111 Opera: Allowing Pop-Ups Enabling Java From Opera, click Tools, then Pr e fe r e nce s. In the Adva nce d tab, select Cont e nt from the leftside menu. Select the check boxes as shown in the following screen. ARMOR Z1 User’s Guide 164 Appendix A Pop-up Windows, JavaScript and Java Permissions Figure 112 Opera: Enabling Java To customize JavaScript behavior in the Opera browser, click Ja va Scr ipt Opt ions. Figure 113 Opera: JavaScript Options Select the items you want Opera’s JavaScript to apply. ARMOR Z1 User’s Guide 165 A PPENDIX Setting Up Your Computer’s IP Address Note: Your specific ARMOR Z1 may not support all of the operating systems described in this appendix. See the product specifications for more information about which operating systems are supported. This appendix shows you how to configure the IP settings on your computer in order for it to be able to communicate with the other devices on your network. Windows Vista/XP/2000, Mac OS 9/ OS X, and all versions of UNIX/LINUX include the software components you need to use TCP/IP on your computer. If you manually assign IP information instead of using a dynamic IP, make sure that your network’s computers have IP addresses that place them in the same subnet. In this appendix, you can set up an IP address for: • Windows XP/NT/2000 on page 166 • Windows Vista on page 169 • Windows 7 on page 172 • Mac OS X: 10.3 and 10.4 on page 176 • Mac OS X: 10.5 and 10.6 on page 179 • Linux: Ubuntu 8 (GNOME) on page 182 • Linux: openSUSE 10.3 (KDE) on page 186 Windows XP/NT/2000 The following example uses the default Windows XP display theme but can also apply to Windows 2000 and Windows NT. Click St a r t > Con t r ol Pa n e l. ARMOR Z1 User’s Guide 166 Appendix B Setting Up Your Computer’s IP Address In the Cont r ol Pa n e l, click the N e t w or k Con ne ct ion s icon. Right-click Loca l Ar e a Conne ct ion and then select Pr ope r t ie s. On the Ge n e r a l tab, select I n t e r n e t Pr ot ocol ( TCP/ I P) and then click Pr ope r t ie s. ARMOR Z1 User’s Guide 167 Appendix B Setting Up Your Computer’s IP Address The I nt e r ne t Pr ot ocol TCP/ I P Pr ope r t ie s window opens. ARMOR Z1 User’s Guide 168 Appendix B Setting Up Your Computer’s IP Address Select Obt a in a n I P a ddr e ss a ut om a t ica lly if your network administrator or ISP assigns your IP address dynamically. Select Use t h e follow in g I P Addr e ss and fill in the I P a ddr e ss, Subn e t m a sk , and D e fa ult ga t e w a y fields if you have a static IP address that was assigned to you by your network administrator or ISP. You may also have to enter a Pr e fe r r e d D N S se r ve r and an Alt e r na t e D N S se r ve r , if that information was provided. Click OK to close the I n t e r ne t Pr ot ocol ( TCP/ I P) Pr ope r t ie s window. Click OK to close the Loca l Ar e a Con n e ct ion Pr ope r t ie s window. Verifying Settings Click St a r t > All Pr ogr a m s > Acce ssor ie s > Com m a nd Pr om pt . In the Com m a nd Pr om pt window, type "ipconfig" and then press [ENTER]. You can also go to St a r t > Con t r ol Pa n e l > N e t w or k Con n e ct ions, right-click a network connection, click St a t u s and then click the Suppor t tab to view your IP address and connection information. Windows Vista This section shows screens from Windows Vista Professional. Click St a r t > Cont r ol Pa n e l. In the Cont r ol Pa n e l, click the N e t w or k a nd I n t e r n e t icon. ARMOR Z1 User’s Guide 169 Appendix B Setting Up Your Computer’s IP Address Click the N e t w or k a n d Sh a r ing Ce n t e r icon. Click M a n a ge n e t w or k con n e ct ions. Right-click Loca l Ar e a Conne ct ion and then select Pr ope r t ie s. Note: During this procedure, click Con t inu e whenever Windows displays a screen saying that it needs your permission to continue. Select I n t e r n e t Pr ot ocol Ve r sion 4 ( TCP/ I Pv4 ) and then select Pr ope r t ie s. ARMOR Z1 User’s Guide 170 Appendix B Setting Up Your Computer’s IP Address The I nt e r ne t Pr ot ocol Ve r sion 4 ( TCP/ I Pv4 ) Pr ope r t ie s window opens. ARMOR Z1 User’s Guide 171 Appendix B Setting Up Your Computer’s IP Address Select Obt a in a n I P a ddr e ss a ut om a t ica lly if your network administrator or ISP assigns your IP address dynamically. Select Use t h e follow in g I P Addr e ss and fill in the I P a ddr e ss, Subn e t m a sk , and D e fa ult ga t e w a y fields if you have a static IP address that was assigned to you by your network administrator or ISP. You may also have to enter a Pr e fe r r e d D N S se r ve r and an Alt e r na t e D N S se r ve r , if that information was provided.Click Adva nce d. Click OK to close the I n t e r ne t Pr ot ocol ( TCP/ I P) Pr ope r t ie s window. 10 Click OK to close the Loca l Ar e a Con n e ct ion Pr ope r t ie s window. Verifying Settings Click St a r t > All Pr ogr a m s > Acce ssor ie s > Com m a nd Pr om pt . In the Com m a nd Pr om pt window, type "ipconfig" and then press [ENTER]. You can also go to St a r t > Con t r ol Pa n e l > N e t w or k Con n e ct ions, right-click a network connection, click St a t u s and then click the Suppor t tab to view your IP address and connection information. Windows 7 This section shows screens from Windows 7 Enterprise. Click St a r t > Cont r ol Pa n e l. In the Cont r ol Pa n e l, click Vie w ne t w or k st a t us a nd t a sk s under the N e t w or k a n d I n t e r n e t category. ARMOR Z1 User’s Guide 172 Appendix B Setting Up Your Computer’s IP Address Click Ch a n ge a da pt e r se t t in gs. Double click Loca l Ar e a Conne ct ion and then select Pr ope r t ie s. ARMOR Z1 User’s Guide 173 Appendix B Setting Up Your Computer’s IP Address Note: During this procedure, click Con t inu e whenever Windows displays a screen saying that it needs your permission to continue. Select I n t e r n e t Pr ot ocol Ve r sion 4 ( TCP/ I Pv4 ) and then select Pr ope r t ie s. The I nt e r ne t Pr ot ocol Ve r sion 4 ( TCP/ I Pv4 ) Pr ope r t ie s window opens. ARMOR Z1 User’s Guide 174 Appendix B Setting Up Your Computer’s IP Address Select Obt a in a n I P a ddr e ss a ut om a t ica lly if your network administrator or ISP assigns your IP address dynamically. Select Use t h e follow in g I P Addr e ss and fill in the I P a ddr e ss, Subn e t m a sk , and D e fa ult ga t e w a y fields if you have a static IP address that was assigned to you by your network administrator or ISP. You may also have to enter a Pr e fe r r e d D N S se r ve r and an Alt e r na t e D N S se r ve r , if that information was provided. Click Adva nce d if you want to configure advanced settings for IP, DNS and WINS. Click OK to close the I n t e r ne t Pr ot ocol ( TCP/ I P) Pr ope r t ie s window. Click OK to close the Loca l Ar e a Con n e ct ion Pr ope r t ie s window. Verifying Settings Click St a r t > All Pr ogr a m s > Acce ssor ie s > Com m a nd Pr om pt . In the Com m a nd Pr om pt window, type "ipconfig" and then press [ENTER]. The IP settings are displayed as follows. ARMOR Z1 User’s Guide 175 Appendix B Setting Up Your Computer’s IP Address Mac OS X: 10.3 and 10.4 The screens in this section are from Mac OS X 10.4 but can also apply to 10.3. Click Apple > Syst e m Pr e fe r e nce s. In the Syst e m Pr e fe r e nce s window, click the N e t w or k icon. ARMOR Z1 User’s Guide 176 Appendix B Setting Up Your Computer’s IP Address When the N e t w or k preferences pane opens, select Built - in Et he r ne t from the network connection type list, and then click Configu r e . For dynamically assigned settings, select Usin g D H CP from the Configu r e I Pv4 list in the TCP/ I P tab. ARMOR Z1 User’s Guide 177 Appendix B Setting Up Your Computer’s IP Address For statically assigned settings, do the following: • From the Configu r e I Pv4 list, select M a nua lly. • In the I P Addr e ss field, type your IP address. • In the Subn e t M a sk field, type your subnet mask. • In the Rou t e r field, type the IP address of your device. Click Apply N ow and close the window. Verifying Settings Check your TCP/IP properties by clicking Applica t ions > Ut ilit ie s > N e t w or k Ut ilit ie s, and then selecting the appropriate N e t w or k I nt e r fa ce from the I n fo tab. ARMOR Z1 User’s Guide 178 Appendix B Setting Up Your Computer’s IP Address Figure 114 Mac OS X 10.4: Network Utility Mac OS X: 10.5 and 10.6 The screens in this section are from Mac OS X 10.5 but can also apply to 10.6. Click Apple > Syst e m Pr e fe r e nce s. In Syst e m Pr e fe r e n ce s, click the N e t w or k icon. ARMOR Z1 User’s Guide 179 Appendix B Setting Up Your Computer’s IP Address When the N e t w or k preferences pane opens, select Et he r ne t from the list of available connection types. From the Configu r e list, select Usin g D H CP for dynamically assigned settings. ARMOR Z1 User’s Guide 180 Appendix B Setting Up Your Computer’s IP Address For statically assigned settings, do the following: • From the Configu r e list, select M a nua lly. • In the I P Addr e ss field, enter your IP address. • In the Subn e t M a sk field, enter your subnet mask. • In the Rou t e r field, enter the IP address of your ARMOR Z1. Click Apply and close the window. Verifying Settings Check your TCP/IP properties by clicking Applica t ions > Ut ilit ie s > N e t w or k Ut ilit ie s, and then selecting the appropriate N e t w or k int e r fa ce from the I nfo tab. ARMOR Z1 User’s Guide 181 Appendix B Setting Up Your Computer’s IP Address Figure 115 Mac OS X 10.5: Network Utility Linux: Ubuntu 8 (GNOME) This section shows you how to configure your computer’s TCP/IP settings in the GNU Object Model Environment (GNOME) using the Ubuntu 8 Linux distribution. The procedure, screens and file locations may vary depending on your specific distribution, release version, and individual configuration. The following screens use the default Ubuntu 8 installation. Note: Make sure you are logged in as the root administrator. Follow the steps below to configure your computer IP address in GNOME: Click Syst e m > Adm in ist r a t ion > N e t w or k . When the N e t w or k Se t t in gs window opens, click Un lock to open the Aut he nt ica t e window. (By default, the Unlock button is greyed out until clicked.) You cannot make changes to your configuration unless you first enter your admin password. ARMOR Z1 User’s Guide 182 Appendix B Setting Up Your Computer’s IP Address In the Aut he nt ica t e window, enter your admin account name and password then click the Aut he nt ica t e button. In the N e t w or k Se t t ings window, select the connection that you want to configure, then click Pr ope r t ie s. ARMOR Z1 User’s Guide 183 Appendix B Setting Up Your Computer’s IP Address The Pr ope r t ie s dialog box opens. • In the Configu r a t ion list, select Au t om a t ic Con figu r a t ion ( D H CP) if you have a dynamic IP address. • In the Configur a t ion list, select St a t ic I P a ddr e ss if you have a static IP address. Fill in the I P a ddr e ss, Subne t m a sk , and Ga t e w a y a ddr e ss fields. Click OK to save the changes and close the Pr ope r t ie s dialog box and return to the N e t w or k Se t t in gs screen. If you know your DNS server IP address(es), click the D N S tab in the N e t w or k Se t t in gs window and then enter the DNS server information in the fields provided. ARMOR Z1 User’s Guide 184 Appendix B Setting Up Your Computer’s IP Address Click the Close button to apply the changes. Verifying Settings Check your TCP/IP properties by clicking Syst e m > Adm in ist r a t ion > N e t w or k Tools, and then selecting the appropriate N e t w or k de vice from the D e vice s tab. The I nt e r fa ce St a t ist ics column shows data if your connection is working properly. ARMOR Z1 User’s Guide 185 Appendix B Setting Up Your Computer’s IP Address Figure 116 Ubuntu 8: Network Tools Linux: openSUSE 10.3 (KDE) This section shows you how to configure your computer’s TCP/IP settings in the K Desktop Environment (KDE) using the openSUSE 10.3 Linux distribution. The procedure, screens and file locations may vary depending on your specific distribution, release version, and individual configuration. The following screens use the default openSUSE 10.3 installation. Note: Make sure you are logged in as the root administrator. Follow the steps below to configure your computer IP address in the KDE: Click K M e n u > Com pu t e r > Adm in ist r a t or Se t t in gs ( Ya ST) . ARMOR Z1 User’s Guide 186 Appendix B Setting Up Your Computer’s IP Address When the Run a s Root - KD E su dialog opens, enter the admin password and click OK. When the Ya ST Cont r ol Ce nt e r window opens, select N e t w or k D e vice s and then click the N e t w or k Ca r d icon. ARMOR Z1 User’s Guide 187 Appendix B Setting Up Your Computer’s IP Address When the N e t w or k Se t t in gs window opens, click the Ove r vie w tab, select the appropriate connection N a m e from the list, and then click the Configu r e button. When the N e t w or k Ca r d Se t u p window opens, click the Addr e ss tab ARMOR Z1 User’s Guide 188 Appendix B Setting Up Your Computer’s IP Address Figure 117 openSUSE 10.3: Network Card Setup Select D yna m ic Addr e ss ( D H CP) if you have a dynamic IP address. Select St a t ica lly a ssign e d I P Addr e ss if you have a static IP address. Fill in the I P a ddr e ss, Subne t m a sk , and H ost na m e fields. Click N e x t to save the changes and close the N e t w or k Ca r d Se t up window. If you know your DNS server IP address(es), click the H ost na m e / D N S tab in N e t w or k Se t t in gs and then enter the DNS server information in the fields provided. ARMOR Z1 User’s Guide 189 Appendix B Setting Up Your Computer’s IP Address Click Finish to save your settings and close the window. Verifying Settings Click the KN e t w or k M a na ge r icon on the Ta sk ba r to check your TCP/IP properties. From the Opt ion s sub-menu, select Sh ow Con n e ct ion I n for m a t ion. Figure 118 openSUSE 10.3: KNetwork Manager When the Conn e ct ion St a t u s - KN e t w or k M a n a ge r window opens, click the St a t ist ics t a b to see if your connection is working properly. ARMOR Z1 User’s Guide 190 Appendix B Setting Up Your Computer’s IP Address Figure 119 openSUSE: Connection Status - KNetwork Manager ARMOR Z1 User’s Guide 191 A PPENDIX Common Services The following table lists some commonly-used services and their associated protocols and port numbers. For a comprehensive list of port numbers, ICMP type/code numbers and services, visit the IANA (Internet Assigned Number Authority) web site. • N a m e : This is a short, descriptive name for the service. You can use this one or create a different one, if you like. • Pr ot ocol: This is the type of IP protocol used by the service. If this is TCP/ UD P, then the service uses the same port number with TCP and UDP. If this is USER- D EFI N ED, the Por t ( s) is the IP protocol number, not the port number. • Por t ( s) : This value depends on the Pr ot ocol. Please refer to RFC 1700 for further information about port numbers. • If the Pr ot ocol is TCP, UD P, or TCP/ UD P, this is the IP port number. • If the Pr ot ocol is USER, this is the IP protocol number. • D e scr ipt ion : This is a brief explanation of the applications that use this service or the situations in which this service is used. Table 61 Commonly Used Services NAME PROTOCOL PORT(S) DESCRIPTION AH (IPSEC_TUNNEL) User-Defined 51 The IPSEC AH (Authentication Header) tunneling protocol uses this service. AIM/New-ICQ TCP 5190 AOL’s Internet Messenger service. It is also used as a listening port by ICQ. AUTH TCP 113 Authentication protocol used by some servers. BGP TCP 179 Border Gateway Protocol. BOOTP_CLIENT UDP 68 DHCP Client. BOOTP_SERVER UDP 67 DHCP Server. CU-SEEME TCP 7648 UDP 24032 A popular videoconferencing solution from White Pines Software. DNS TCP/UDP 53 Domain Name Server, a service that matches web names (for example www.zyxel.com) to IP numbers. ESP (IPSEC_TUNNEL) User-Defined 50 The IPSEC ESP (Encapsulation Security Protocol) tunneling protocol uses this service. FINGER TCP 79 Finger is a UNIX or Internet related command that can be used to find out if a user is logged on. FTP TCP 20 TCP 21 File Transfer Program, a program to enable fast transfer of files, including large files that may not be possible by e-mail. H.323 TCP 1720 NetMeeting uses this protocol. HTTP TCP 80 Hyper Text Transfer Protocol - a client/server protocol for the world wide web. ARMOR Z1 User’s Guide 192 Appendix C Common Services Table 61 Commonly Used Services (continued) NAME PROTOCOL PORT(S) DESCRIPTION HTTPS TCP 443 HTTPS is a secured http session often used in ecommerce. ICMP User-Defined Internet Control Message Protocol is often used for diagnostic or routing purposes. ICQ UDP 4000 This is a popular Internet chat program. IGMP (MULTICAST) User-Defined Internet Group Management Protocol is used when sending packets to a specific group of hosts. IKE UDP 500 The Internet Key Exchange algorithm is used for key distribution and management. IRC TCP/UDP 6667 This is another popular Internet chat program. MSN Messenger TCP 1863 Microsoft Networks’ messenger service uses this protocol. NEW-ICQ TCP 5190 An Internet chat program. NEWS TCP 144 A protocol for news groups. NFS UDP 2049 Network File System - NFS is a client/server distributed file service that provides transparent file sharing for network environments. NNTP TCP 119 Network News Transport Protocol is the delivery mechanism for the USENET newsgroup service. PING User-Defined Packet INternet Groper is a protocol that sends out ICMP echo requests to test whether or not a remote host is reachable. POP3 TCP 110 Post Office Protocol version 3 lets a client computer get e-mail from a POP3 server through a temporary connection (TCP/IP or other). PPTP TCP 1723 Point-to-Point Tunneling Protocol enables secure transfer of data over public networks. This is the control channel. PPTP_TUNNEL (GRE) User-Defined 47 PPTP (Point-to-Point Tunneling Protocol) enables secure transfer of data over public networks. This is the data channel. RCMD TCP 512 Remote Command Service. REAL_AUDIO TCP 7070 A streaming audio service that enables real time sound over the web. REXEC TCP 514 Remote Execution Daemon. RLOGIN TCP 513 Remote Login. RTELNET TCP 107 Remote Telnet. RTSP TCP/UDP 554 The Real Time Streaming (media control) Protocol (RTSP) is a remote control for multimedia on the Internet. SFTP TCP 115 Simple File Transfer Protocol. SMTP TCP 25 Simple Mail Transfer Protocol is the messageexchange standard for the Internet. SMTP enables you to move messages from one e-mail server to another. SNMP TCP/UDP 161 Simple Network Management Program. SNMP-TRAPS TCP/UDP 162 Traps for use with the SNMP (RFC:1215). ARMOR Z1 User’s Guide 193 Appendix C Common Services Table 61 Commonly Used Services (continued) NAME PROTOCOL PORT(S) DESCRIPTION SQL-NET TCP 1521 Structured Query Language is an interface to access data on many different types of database systems, including mainframes, midrange systems, UNIX systems and network servers. SSH TCP/UDP 22 Secure Shell Remote Login Program. STRM WORKS UDP 1558 Stream Works Protocol. SYSLOG UDP 514 Syslog allows you to send system logs to a UNIX server. TACACS UDP 49 Login Host Protocol used for (Terminal Access Controller Access Control System). TELNET TCP 23 Telnet is the login and terminal emulation protocol common on the Internet and in UNIX environments. It operates over TCP/IP networks. Its primary function is to allow users to log into remote host systems. TFTP UDP 69 Trivial File Transfer Protocol is an Internet file transfer protocol similar to FTP, but uses the UDP (User Datagram Protocol) rather than TCP (Transmission Control Protocol). VDOLIVE TCP 7000 Another videoconferencing solution. ARMOR Z1 User’s Guide 194 A PPENDIX Legal Information Copyright Copyright © 2015 by ZyXEL Communications Corporation. The contents of this publication may not be reproduced in any part or as a whole, transcribed, stored in a retrieval system, translated into any language, or transmitted in any form or by any means, electronic, mechanical, magnetic, optical, chemical, photocopying, manual, or otherwise, without the prior written permission of ZyXEL Communications Corporation. Published by ZyXEL Communications Corporation. All rights reserved. Disclaimer ZyXEL does not assume any liability arising out of the application or use of any products, or software described herein. Neither does it convey any license under its patent rights nor the patent rights of others. ZyXEL further reserves the right to make changes in any products described herein without notice. This publication is subject to change without notice. Regulatory Notice and Statement UNITED STATE AMERICA The following information applies if you use the product within USA area. FCC EMC Statement • The device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. • Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. • This product has been tested and complies with the specifications for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used according to the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. • If this equipment does cause harmful interference to radio or television reception, which is found by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: •Reorient or relocate the receiving antenna •Increase the separation between the equipment or devices •Connect the equipment to an outlet other than the receiver’s • •Consult a dealer or an experienced radio/TV technician for assistance Note: This device is restricted for the indoor usage only. FCC Radiation Exposure Statement This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This transmitter must be at least 30 cm from the user and must not be co-located or operating in conjunction with any other antenna or transmitter. CANADA The following information applies if you use the product within Canada area Industry Canada ICES statement CAN ICES-3 (B)/NMB-3(B) Industry Canada RSS-GEN & RSS-210 statement • This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions:(1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device. ARMOR Z1 User’s Guide 195 Appendix D Legal Information • • This radio transmitter (2468C-NBG6816) has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. Antenna Type: Dipole Antenna (Reversed-SMA Connector) Antenna Gain: -2.4G: 2.94dBi -5G (5150-5250MHz): 4.26dBi; 5G (5725-5850MHz): 4.15dBi If you use the produce with 5G wireless function, the following attention shall be paid that, (i) the device is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems; (ii) the maximum antenna gain permitted for devices in the band 5725-5825 MHz shall comply with the e.i.r.p. limits specified for pointto-point and non point-to-point operation as appropriate. • Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage; (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement. • Le présent émetteur radio (2468C-NBG6816) de modèle s'il fait partie du matériel de catégorieI) a été approuvé par Industrie Canada pour fonctionner avec les types d'antenne énumérés ci-dessous et ayant un gain admissible maximal et l'impédance requise pour chaque type d'antenne. Les types d'antenne non inclus dans cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation de l'émetteur. • Si vous utilisez le produit avec 5G sans fil fonction, suivant l'attention doit être versée que, (i) les dispositifs fonctionnant dans la bande 5150-5250 MHz sont réservés uniquement pour une utilisation à l’intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux; (ii) le gain maximal d’antenne permis (pour les dispositifs utilisant la bande 5725-5825 MHz) doit se conformer à la limite de p.i.r.e. spécifiée pour l’exploitation point à point et non point à point, selon le cas. Industry Canada Radiation Exposure Statement This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 30 cm between the radiator and your body. Déclaration d’exposition aux radiations: Cet équipement est conforme aux limites d’exposition aux rayonnements IC établies pour un environnement non contrôlé.Cet équipement doit être installé et utilisé avec un minimum de 30 cm de distance entre la source de rayonnement et votre corps. EUROPEAN UNION The following information applies if you use the product within the European Union. Declaration of Conformity with Regard to EU Directive 1999/5/EC (R&TTE Directive) Compliance information for 2.4GHz and/or 5GHz wireless products relevant to the EU and other Countries following the EU Directive 1999/ 5/EC (R&TTE) Б (Bulgarian) С Español (Spanish) Por medio de la presente ZyXEL declara que el equipo cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE. Čeština (Czech) ZyXEL tímto prohlašuje, že tento zařízení je ve shodě se základními požadavky a dalšími příslušnými ustanoveními směrnice 1999/5/EC. Dansk (Danish) Undertegnede ZyXEL erklærer herved, at følgende udstyr udstyr overholder de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF. Deutsch (German) Hiermit erklärt ZyXEL, dass sich das Gerät Ausstattung in Übereinstimmung mit den grundlegenden Anforderungen und den übrigen einschlägigen Bestimmungen der Richtlinie 1999/5/EU befindet. Eesti keel (Estonian) Käesolevaga kinnitab ZyXEL seadme seadmed vastavust direktiivi 1999/5/EÜ põhinõuetele ja nimetatud direktiivist tulenevatele teistele asjakohastele sätetele. Ε η ά (Greek) я Ε Η Ε ZyXEL Α ΧΕ ,ч Α ZyXEL ∆Η Ω Ε Ε ∆ Α Α Ε Η я 1999/5/ C. ε π σ ός ∆ΗΓ Α 1999/5/ΕC. ΦΩ Ε Α Ω∆Ε Α Α Η Ε Α English Hereby, ZyXEL declares that this equipment is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. Français (French) Par la présente ZyXEL déclare que l'appareil équipements est conforme aux exigences essentielles et aux autres dispositions pertinentes de la directive 1999/5/EC. Hrvatski (Croatian) ZyXEL ovime izjavljuje da je radijska oprema tipa u skladu s Direktivom 1999/5/EC. Íslenska (Icelandic) Hér með lýsir, ZyXEL því yfir að þessi búnaður er í samræmi við grunnkröfur og önnur viðeigandi ákvæði tilskipunar 1999/5/EC. ARMOR Z1 User’s Guide 196 Appendix D Legal Information Italiano (Italian) Con la presente ZyXEL dichiara che questo attrezzatura è conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE. Latviešu valoda (Latvian) Ar šo ZyXEL deklarē, ka iekārtas atbilst Direktīvas 1999/5/EK būtiskajām prasībām un citiem ar to saistītajiem noteikumiem. Lietuvių kalba (Lithuanian) Šiuo ZyXEL deklaruoja, kad šis įranga atitinka esminius reikalavimus ir kitas 1999/5/EB Direktyvos nuostatas. Magyar (Hungarian) Alulírott, ZyXEL nyilatkozom, hogy a berendezés megfelel a vonatkozó alapvetõ követelményeknek és az 1999/5/EK irányelv egyéb elõírásainak. Malti (Maltese) Hawnhekk, ZyXEL, jiddikjara li dan tagħmir jikkonforma mal-ħtiġijiet essenzjali u ma provvedimenti oħrajn relevanti li hemm fid-Dirrettiva 1999/5/EC. Nederlands (Dutch) Hierbij verklaart ZyXEL dat het toestel uitrusting in overeenstemming is met de essentiële eisen en de andere relevante bepalingen van richtlijn 1999/5/EC. Polski (Polish) Niniejszym ZyXEL oświadcza, że sprzęt jest zgodny z zasadniczymi wymogami oraz pozostałymi stosownymi postanowieniami Dyrektywy 1999/5/EC. Português (Portuguese) ZyXEL declara que este equipamento está conforme com os requisitos essenciais e outras disposições da Directiva 1999/5/EC. Română (Romanian) Prin prezenta, ZyXEL declară că acest echipament este în conformitate cu cerinţele esenţiale şi alte prevederi relevante ale Directivei 1999/5/EC. Slovenčina (Slovak) ZyXEL týmto vyhlasuje, že zariadenia spĺňa základné požiadavky a všetky príslušné ustanovenia Smernice 1999/5/EC. Slovenščina (Slovene) ZyXEL izjavlja, da je ta oprema v skladu z bistvenimi zahtevami in ostalimi relevantnimi določili direktive 1999/5/EC. Suomi (Finnish) ZyXEL vakuuttaa täten että laitteet tyyppinen laite on direktiivin 1999/5/EY oleellisten vaatimusten ja sitä koskevien direktiivin muiden ehtojen mukainen. Svenska (Swedish) Härmed intygar ZyXEL att denna utrustning står I överensstämmelse med de väsentliga egenskapskrav och övriga relevanta bestämmelser som framgår av direktiv 1999/5/EC. Norsk (Norwegian) Erklærer herved ZyXEL at dette utstyret er I samsvar med de grunnleggende kravene og andre relevante bestemmelser I direktiv 1999/5/EF. National Restrictions This product may be used in all EU countries (and other countries following the EU Directive 1999/5/EC) without any limitation except for the countries mentioned below: Ce produit peut être utilisé dans tous les pays de l’UE (et dans tous les pays ayant transposés la directive 1999/5/CE) sans aucune limitation, excepté pour les pays mentionnés ci-dessous: Questo prodotto è utilizzabile in tutte i paesi EU (ed in tutti gli altri paesi che seguono le direttiva 1999/5/EC) senza nessuna limitazione, eccetto per i paesii menzionati di seguito: Das Produkt kann in allen EU Staaten ohne Einschränkungen eingesetzt werden (sowie in anderen Staaten die der Richtlinie 1999/5/CE folgen) mit Außnahme der folgenden aufgeführten Staaten: In the majority of the EU and other European countries, the 2.4GHz and 5GHz bands have been made available for the use of wireless local area networks (LANs). Later in this document you will find an overview of countries in which additional restrictions or requirements or both are applicable. The requirements for any country may evolve. ZyXEL recommends that you check with the local authorities for the latest status of their national regulations for both the 2.4GHz and 5GHz wireless LANs. The following countries have restrictions and/or requirements in addition to those given in the table labeled “Overview of Regulatory Requirements for Wireless LANs”:. Belgium The Belgian Institute for Postal Services and Telecommunications (BIPT) must be notified of any outdoor wireless link having a range exceeding 300 meters. Please check http://www.bipt.be for more details. Draadloze verbindingen voor buitengebruik en met een reikwijdte van meer dan 300 meter dienen aangemeld te worden bij het Belgisch Instituut voor postdiensten en telecommunicatie (BIPT). Zie http://www.bipt.be voor meer gegevens. Les liaisons sans fil pour une utilisation en extérieur d’une distance supérieure à 300 mètres doivent être notifiées à l’Institut Belge des services Postaux et des Télécommunications (IBPT). Visitez http://www.ibpt.be pour de plus amples détails. Denmark In Denmark, the band 5150 - 5350 MHz is also allowed for outdoor usage. I Danmark må frekvensbåndet 5150 - 5350 også anvendes udendørs. Italy This product meets the National Radio Interface and the requirements specified in the National Frequency Allocation Table for Italy. Unless this wireless LAN product is operating within the boundaries of the owner's property, its use requires a “general authorization.” Please check http://www.sviluppoeconomico.gov.it/ for more details. Questo prodotto è conforme alla specifiche di Interfaccia Radio Nazionali e rispetta il Piano Nazionale di ripartizione delle frequenze in ARMOR Z1 User’s Guide 197 Appendix D Legal Information Italia. Se non viene installato all 'interno del proprio fondo, l'utilizzo di prodotti Wireless LAN richiede una “Autorizzazione Generale”. Consultare http://www.sviluppoeconomico.gov.it/ per maggiori dettagli. Latvia The outdoor usage of the 2.4 GHz band requires an authorization from the Electronic Communications Office. Please check http:// www.esd.lv for more details. 2.4 GHz frekvenèu joslas izmantoðanai ârpus telpâm nepiecieðama atïauja no Elektronisko sakaru direkcijas. Vairâk informâcijas: http:// www.esd.lv. N ot e s: 1. Although Norway, Switzerland and Liechtenstein are not EU member states, the EU Directive 1999/5/EC has also been implemented in those countries. 2. The regulatory limits for maximum output power are specified in EIRP. The EIRP level (in dBm) of a device can be calculated by adding the gain of the antenna used(specified in dBi) to the output power available at the connector (specified in dBm). List of national codes COUNTRY ISO 3166 2 LETTER CODE COUNTRY ISO 3166 2 LETTER CODE Austria AT Liechtenstein LI Belgium BE Lithuania LT Bulgaria BG Luxembourg LU Croatia HR Malta MT Cyprus CY Netherlands NL Czech Republic CZ Norway NO Denmark DK Poland PL Estonia EE Portugal PT Finland FI Romania RO France FR Serbia RS Germany DE Slovakia SK Greece GR Slovenia SI Hungary HU Spain ES Iceland IS Switzerland CH Ireland IE Sweden SE Italy IT Turkey TR Latvia LV United Kingdom GB Safety Warnings • DO NOT use this product near water, for example, in a wet basement or near a swimming pool. • DO NOT expose your device to dampness, dust or corrosive liquids. • DO NOT store things on the device. • DO NOT install, use, or service this device during a thunderstorm. There is a remote risk of electric shock from lightning. • Connect ONLY suitable accessories to the device. • DO NOT open the device or unit. Opening or removing covers can expose you to dangerous high voltage points or other risks. ONLY qualified service personnel should service or disassemble this device. Please contact your vendor for further information. • Make sure to connect the cables to the correct ports. • Place connecting cables carefully so that no one will step on them or stumble over them. • Always disconnect all cables from this device before servicing or disassembling. • Use ONLY an appropriate power adaptor or cord for your device. Connect it to the right supply voltage (for example, 110V AC in North America or 230V AC in Europe). • DO NOT remove the plug and connect it to a power outlet by itself; always attach the plug to the power adaptor first before connecting it to a power outlet. • DO NOT allow anything to rest on the power adaptor or cord and do NOT place the product where anyone can walk on the power adaptor or cord. • DO NOT use the device if the power adaptor or cord is damaged as it might cause electrocution. • If the power adaptor or cord is damaged, remove it from the device and the power source. • DO NOT attempt to repair the power adaptor or cord. Contact your local vendor to order a new one. • DO NOT use the device outside, and make sure all the connections are indoors. There is a remote risk of electric shock from lightning. • CAUTION: RISK OF EXPLOSION IF BATTERY (on the motherboard) IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS. Dispose them at the applicable collection point for the recycling of electrical and ARMOR Z1 User’s Guide 198 Appendix D Legal Information electronic equipment. For detailed information about recycling of this product, please contact your local city office, your household waste disposal service or the store where you purchased the product. • DO NOT obstruct the device ventilation slots, as insufficient airflow may harm your device. The following warnings apply if product is disconnect device? • A readily accessible disconnect device shall be incorporated external to the equipment; and/or • The socket-outlet shall be installed near the equipment and shall be easily accessible. Environment Statement ErP (Energy-related Products) ZyXEL products put on the EU market in compliance with the requirement of the European Parliament and the Council published Directive 2009/125/EC establishing a framework for the setting of ecodesign requirements for energy-related products (recast), so called as "ErP Directive (Energy-related Products directive) as well as ecodesign requirement laid down in applicable implementing measures, power consumption has satisfied regulation requirements which are: Network standby power consumption < 12W, and/or Off mode power consumption < 0.5W, and/or Standby mode power consumption < 0.5W. Wireless setting, please refer to "Wireless" chapter for more detail. WEEE Directive Your product is marked with this symbol, which is known as the WEEE mark. WEEE stands for Waste Electronics and Electrical Equipment. It means that used electrical and electronic products should not be mixed with general waste. Used electrical and electronic equipment should be treated separately. "INFORMAZIONI AGLI UTENTI" Ai sensi della Direttiva 2012/19/UE del Parlamento europeo e del Consiglio, del 4 luglio 2012, sui rifiuti di apparecchiature elettriche ed elettroniche (RAEE) Il simbolo del cassonetto barrato riportato sull’apparecchiatura o sulla sua confezione indica che il prodotto alla fine della propria vita utile deve essere raccolto separatamente dagli altri rifiuti. La raccolta differenziata della presente apparecchiatura giunta a fine vita e organizzata e gestita dal produttore. L’utente che vorra disfarsi della presente apparecchiatura dovra quindi contattare il produttore e seguire il sistema che questo ha adottato per consentire la raccolta separata dell’apparecchiatura giunta a fine vita. L’adeguata raccolta differenziata per l’avvio successivo dell’apparecchiatura dismessa al riciclaggio, al trattamento e allo smaltimento ambientalmente compatibile contribuisce ad evitare possibili effetti negativi sull’ambiente e sulla salute e favorisce il reimpiego e/o riciclo dei materiali di cui e composta l’apparecchiatura. Lo smaltimento abusivo del prodotto da parte del detentore comporta l’applicazione delle sanzioni amministrative previste dalla normativa vigente." ARMOR Z1 User’s Guide 199 Appendix D Legal Information Environmental Product Declaration ARMOR Z1 User’s Guide 200 Appendix D Legal Information 灣 以下訊息僅適用於產品銷售至 第 二條 經型式認證合格之低 第 四條 低 灣地 率射頻電機，非經許 ，公司 商號或使用者均不得擅自變更頻率 大 率或變更原設計之特性及 能 率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立即停用，並改善至無干擾時方得繼續使用 前項合法通信，指依電信法規定作業之無線電通信 低 率射頻電機須忍受合法通信或工業 科學及醫療用電波輻射性電機設備之干擾 Viewing Certifications Go to http://www.zyxel.com to view this product’s documentation and certifications. ZyXEL Limited Warranty ZyXEL warrants to the original end user (purchaser) that this product is free from any defects in material or workmanship for a specific period (the Warranty Period) from the date of purchase. The Warranty Period varies by region. Check with your vendor and/or the authorized ZyXEL local distributor for details about the Warranty Period of this product. During the warranty period, and upon proof of purchase, should the product have indications of failure due to faulty workmanship and/or materials, ZyXEL will, at its discretion, repair or replace the defective products or components without charge for either parts or labor, and to whatever extent it shall deem necessary to restore the product or components to proper operating condition. Any replacement will consist of a new or re-manufactured functionally equivalent product of equal or higher value, and will be solely at the discretion of ZyXEL. This warranty shall not apply if the product has been modified, misused, tampered with, damaged by an act of God, or subjected to abnormal working conditions. Note Repair or replacement, as provided under this warranty, is the exclusive remedy of the purchaser. This warranty is in lieu of all other warranties, express or implied, including any implied warranty of merchantability or fitness for a particular use or purpose. ZyXEL shall in no event be held liable for indirect or consequential damages of any kind to the purchaser. To obtain the services of this warranty, contact your vendor. You may also refer to the warranty policy for the region in which you bought the device at http://www.zyxel.com/web/support_warranty_info.php. Registration Register your product online to receive e-mail notices of firmware upgrades and information at www.zyxel.com for global products, or at www.us.zyxel.com for North American products. Open Source Licenses This product contains in part some free software distributed under GPL license terms and/or GPL like licenses. Open source licenses are provided with the firmware package. You can download the latest firmware at www.zyxel.com. To obtain the source code covered under those Licenses, please contact support@zyxel.com.tw to get it. ARMOR Z1 User’s Guide 201 A PPENDIX Customer Support In the event of problems that cannot be solved by using this manual, you should contact your vendor. If you cannot contact your vendor, then contact a ZyXEL office for the region in which you bought the device. Regional websites are listed below. See also http://www.zyxel.com/about_zyxel/zyxel_worldwide.shtml. Please have the following information ready when you contact an office. Required Information • Product model and serial number. • Warranty Information. • Date that you received your device. • Brief description of the problem and the steps you took to solve it. Corporate Headquarters (Worldwide) Taiwan • ZyXEL Communications Corporation • http://www.zyxel.com Asia China • ZyXEL Communications (Shanghai) Corp. ZyXEL Communications (Beijing) Corp. ZyXEL Communications (Tianjin) Corp. • http://www.zyxel.cn India • ZyXEL Technology India Pvt Ltd • http://www.zyxel.in Kazakhstan • ZyXEL Kazakhstan • http://www.zyxel.kz ARMOR Z1 User’s Guide 202 Appendix E Customer Support Korea • ZyXEL Korea Corp. • http://www.zyxel.kr Malaysia • ZyXEL Malaysia Sdn Bhd. • http://www.zyxel.com.my Pakistan • ZyXEL Pakistan (Pvt.) Ltd. • http://www.zyxel.com.pk Philipines • ZyXEL Philippines • http://www.zyxel.com.ph Singapore • ZyXEL Singapore Pte Ltd. • http://www.zyxel.com.sg Taiwan • ZyXEL Communications Corporation • http://www.zyxel.com Thailand • ZyXEL Thailand Co., Ltd • http://www.zyxel.co.th Vietnam • ZyXEL Communications Corporation-Vietnam Office • http://www.zyxel.com/vn/vi Europe Austria • ZyXEL Deutschland GmbH • http://www.zyxel.de ARMOR Z1 User’s Guide 203 Appendix E Customer Support Belarus • ZyXEL BY • http://www.zyxel.by Belgium • ZyXEL Communications B.V. • http://www.zyxel.com/be/nl/ Bulgaria • ZyXEL България • http://www.zyxel.com/bg/bg/ Czech • ZyXEL Communications Czech s.r.o • http://www.zyxel.cz Denmark • ZyXEL Communications A/S • http://www.zyxel.dk Estonia • ZyXEL Estonia • http://www.zyxel.com/ee/et/ Finland • ZyXEL Communications • http://www.zyxel.fi France • ZyXEL France • http://www.zyxel.fr Germany • ZyXEL Deutschland GmbH • http://www.zyxel.de Hungary • ZyXEL Hungary & SEE • http://www.zyxel.hu Latvia • ZyXEL Latvia ARMOR Z1 User’s Guide 204 Appendix E Customer Support • http://www.zyxel.com/lv/lv/homepage.shtml Lithuania • ZyXEL Lithuania • http://www.zyxel.com/lt/lt/homepage.shtml Netherlands • ZyXEL Benelux • http://www.zyxel.nl Norway • ZyXEL Communications • http://www.zyxel.no Poland • ZyXEL Communications Poland • http://www.zyxel.pl Romania • ZyXEL Romania • http://www.zyxel.com/ro/ro Russia • ZyXEL Russia • http://www.zyxel.ru Slovakia • ZyXEL Communications Czech s.r.o. organizacna zlozka • http://www.zyxel.sk Spain • ZyXEL Spain • http://www.zyxel.es Sweden • ZyXEL Communications • http://www.zyxel.se Switzerland • Studerus AG ARMOR Z1 User’s Guide 205 Appendix E Customer Support • http://www.zyxel.ch/ Turkey • ZyXEL Turkey A.S. • http://www.zyxel.com.tr UK • ZyXEL Communications UK Ltd. • http://www.zyxel.co.uk Ukraine • ZyXEL Ukraine • http://www.ua.zyxel.com Latin America Argentina • ZyXEL Communication Corporation • http://www.zyxel.com/ec/es/ Ecuador • ZyXEL Communication Corporation • http://www.zyxel.com/ec/es/ Middle East Egypt • ZyXEL Communication Corporation • http://www.zyxel.com/homepage.shtml Middle East • ZyXEL Communication Corporation • http://www.zyxel.com/homepage.shtml North America USA • ZyXEL Communications, Inc. - North America Headquarters • http://www.us.zyxel.com/ ARMOR Z1 User’s Guide 206 Appendix E Customer Support Oceania Australia • ZyXEL Communications Corporation • http://www.zyxel.com/au/en/ Africa South Africa • Nology (Pty) Ltd. • http://www.zyxel.co.za ARMOR Z1 User’s Guide 207 Index Index see also Dynamic Host Configuration Protocol DHCP server 59, 102 Address Assignment 66 Digital Living Network Alliance 107 AP 10 disclaimer 195 AP Mode menu 45 status screen 43 DLNA 107, 117 indexing 118 overview 117 rescan 118 AP+Bridge 10 DLNA-compliant client 107 DNS Server 66 documentation related 2 Domain Name System. See DNS. Bridge/Repeater 10 duplex setting 37, 45 Dynamic Host Configuration Protocol 59 DynDNS 133 DynDNS see also DDNS 133 certifications 197 viewing 201 Channel 37, 44 channel 83 encryption 84 and local (user) database 85 key 85 WPA compatible 85 CIFS 107 Common Internet File System, see CIFS Configuration restore 141, 144, 146 ESSID 154 contact information 202 content filtering by keyword (in URL) 106 copyright 195 CPU usage 37, 44 FCC interference statement 197 customer support 202 file sharing 120 access right 121, 123 bandwidth 123 example 123 FTP 122, 127 overview 120 Samba 120 user account 121, 122 Windows Explorer 120 Daylight saving 139 DDNS service providers 133 DHCP 59 ARMOR Z1 User’s Guide 208 Index work group 120 Firewall guidelines 131 ICMP packets 133 MAC 95 MAC address 66, 83 cloning 66 firewall stateful inspection 130 MAC address filter 83 Firmware upload 140 file extension using HTTP MAC address filtering 95 MAC filter 95 managing the device good habits 11 using the web configurator. See web configurator. using the WPS. See WPS. firmware version 36, 44 MBSSID 10 Media access control 95 General wireless LAN screen 87 media client 117 Guest WLAN 85 Guest WLAN Bandwidth 86 media file 117, 118 type 118 Guide Quick Start 2 media server overview 117 meida file play 117 Memory usage 37, 44 mode 10 Multicast 67 IGMP 67 IGMP 67 see also Internet Group Multicast Protocol version IGMP version 67 Internet Group Multicast Protocol 67 IP Address 102 NAT Traversal 128 Navigation Panel 38, 45 navigation panel 38, 45 LAN 101 LAN overview 101 LAN setup 101 operating mode 10 Language 142 other documentation 2 Link type 37, 44 local (user) database 84 and encryption 85 Local Area Network 101 Point-to-Point Protocol over Ethernet 73 port speed 37, 45 PPPoE 73 ARMOR Z1 User’s Guide 209 Index dial-up connection TCP/IP configuration 59 Time setting 138 Quality of Service (QoS) 97 Quick Start Guide 2 Universal Plug and Play 119 Application 128 Security issues 129 RADIUS server 84 UPnP 119 related documentation 2 user authentication 84 local (user) database 84 RADIUS server 84 Reset button 11 Reset the device 11 Restore configuration 141, 144, 146 Roaming 96 Router Mode status screen 35 WAN (Wide Area Network) 65 RTS/CTS Threshold 83, 96, 97 WAN MAC address 66 warranty 201 note 201 Samba 107 Web Configurator how to access 15 Overview 15 Scheduling 99 web configurator 10 Server Message Block, see SMB WEP Encryption 90 Service Set 88, 94 windows media player 117 Service Set IDentification 88, 94 wireless channel 154 Service Set IDentity. See SSID. wireless LAN 154 SMB 107 wireless LAN scheduling 99 SSID 37, 44, 83, 88, 94 Wireless network basic guidelines 83 channel 83 encryption 84 example 82 MAC address filter 83 overview 82 security 83 SSID 83 stateful inspection firewall 130 Static DHCP 61 Status 35 StreamBoost bandwidth 114 device priority 116 example 114 Subnet Mask 102 Wireless security 83 overview 83 type 83 System General Setup 136 System restart 142 wireless security 154 ARMOR Z1 User’s Guide 210 Index Wireless tutorial 48 Wizard setup 18 WLAN button 11 work group 107 name 107 Windows 107 WPA compatible 85 WPS 10 ARMOR Z1 User’s Guide 211
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : Yes Encryption : Standard V4.4 (128-bit) User Access : Print, Annotate, Fill forms, Extract, Print high-res Author : ZT02102 Create Date : 2015:06:25 09:15:15Z Modify Date : 2015:06:25 09:40:02+08:00 Has XFA : No XMP Toolkit : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03 Creator Tool : FrameMaker 9.0 Metadata Date : 2015:06:25 09:40:02+08:00 Format : application/pdf Title : Book.book Creator : ZT02102 Producer : Acrobat Distiller 11.0 (Windows) Document ID : uuid:530af6ad-36bf-4512-a22f-124bf04109e1 Instance ID : uuid:ab9ac662-c16b-45fa-97ca-34cfbc23b163 Page Mode : UseOutlines Page Count : 55EXIF Metadata provided by EXIF.tools