ZyXEL Communications P330W 802.11g Wireless Broadband Router User Manual WR254MNL 1

ZyXEL Communications Corporation 802.11g Wireless Broadband Router WR254MNL 1

User Manual

Download: ZyXEL Communications P330W 802.11g Wireless Broadband Router User Manual WR254MNL 1
Mirror Download [FCC.gov]ZyXEL Communications P330W 802.11g Wireless Broadband Router User Manual WR254MNL 1
Document ID821625
Application ID7rPCisWEAOUxNPs55S71aQ==
Document DescriptionUser Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize185.23kB (2315352 bits)
Date Submitted2007-07-27 00:00:00
Date Available2007-07-27 00:00:00
Creation Date2007-06-07 11:35:43
Producing SoftwareGNU Ghostscript 7.06
Document Lastmod2007-07-27 13:29:37
Document TitleMicrosoft Word - WR254MNL-1.DOC
Document CreatorPScript5.dll Version 5.2
Document Author: ken

Multi-Function
802.11b+g Wireless
Router
802.11g/802.11b Wireless Access Point
Broadband Internet Access
4-Port Switching Hub
User’s Manual
Table of Contents
INTRODUCTION ............................................................................................................... 2
Wireless Router Features............................................................................................. 2
Package Contents ......................................................................................................... 4
Physical Details ............................................................................................................ 5
INSTALLATION................................................................................................................. 7
Requirements ............................................................................................................... 7
Procedure ..................................................................................................................... 7
SETUP.................................................................................................................................. 9
Overview....................................................................................................................... 9
Configuration Program................................................................................................ 9
Setup Wizard.............................................................................................................. 11
Configuration via Web............................................................................................... 13
PC CONFIGURATION..................................................................................................... 33
Overview..................................................................................................................... 33
Windows Clients......................................................................................................... 33
Macintosh Clients....................................................................................................... 45
Linux Clients .............................................................................................................. 45
Other Unix Systems.................................................................................................... 45
Wireless Station Configuration.................................................................................. 46
APPENDIX A TROUBLESHOOTING .............................................................. 47
Overview..................................................................................................................... 47
General Problems....................................................................................................... 47
Internet Access ........................................................................................................... 47
Wireless Access .......................................................................................................... 48
APPENDIX B ABOUT WIRELESS LANS ........................................................ 49
Modes ......................................................................................................................... 49
BSS/ESS...................................................................................................................... 49
Channels ..................................................................................................................... 49
WEP............................................................................................................................ 50
Wireless LAN Configuration ..................................................................................... 50
APPENDIX C SPECIFICATIONS ................................................................................... 51
Multi-Function Wireless Router ................................................................................ 51
Wireless Interface ...................................................................................................... 51
Regulatory Approvals ................................................................................................ 52
Chapter 1: I n tro d u c ti o n
This Chapter provides an overview of the Wireless Router's features and capabilities.
Congratulations on the purchase of your new Wireless Router. The Wireless Router is a multifunction device providing the following services:
•
•
•
Shared Broadband Internet Access for all LAN users.
4-Port Switching Hub for 10BaseT or 100BaseT connections.
Wireless Access Point for 802.11b and 802.11g Wireless Stations.
Wireless Router Features
The Wireless Router incorporates many advanced features, carefully designed to provide
sophisticated functions while being easy to use.
Internet Access Features
•
Shared Internet Access. All users on the LAN or WLAN can access the Internet
•
DSL & Cable Modem Support. The Wireless Router has a 10/100BaseT Ethernet
•
PPPoE, and PPTP. The Internet (WAN port) connection supports PPPoE (PPP over
Ethernet), PPTP (Peer-to-Peer Tunneling Protocol), as well as "Direct Connection" type
services. Unnumbered IP with PPPoE is also supported.
•
through the Wireless Router, using only a single external IP Address. The local (invalid)
IP Addresses are hidden from external sources. This process is called NAT (Network
Address Translation).
port for connecting a DSL or Cable Modem. All popular DSL and Cable Modems are
supported. SingTel RAS and Big Pond (Australia) login support is also included.
Fixed or Dynamic IP Address. On the Internet (WAN port) connection, the Wireless
Router supports both Dynamic IP Address (IP Address is allocated on connection) and
Fixed IP Address.
Introduction
Advanced Internet Functions
•
Communication Applications. Support for Internet communication applications, such
•
Special Internet Applications. Applications which use non-standard connections or
•
Virtual Servers. This feature allows Internet users to access Internet servers on your
LAN. The required setup is quick and easy.
•
•
•
as interactive Games, Telephony, and Conferencing applications, which are often difficult
to use when behind a Firewall, is included.
port numbers are normally blocked by the Firewall. The ability to define and allow such
applications is provided, to enable such applications to be used normally.
DDNS Support. DDNS (Dynamic DNS) allows Internet users to connect to Virtual
Servers on your LAN using a domain name, even if your IP address is not fixed.
DMZ. For each WAN (Internet) IP address allocated to you, only one (1) PC on your
local LAN can be configured to allow unrestricted 2-way communication with Servers or
individual users on the Internet. This provides the ability to run programs which are
incompatible with Firewalls.
•
URL Filter. Use the URL Filter to block access to undesirable Web sites by LAN users.
Internet Access Log. See which Internet connections have been made.
Access Control. Using the Access Control feature, you can assign LAN users to
•
VPN Pass through Support. PCs with VPN (Virtual Private Networking) software
•
different groups, and determine which Internet services are available to each group.
using PPTP, L2TP and IPSec are transparently supported - no configuration is required.
Wireless Features
•
•
•
•
•
•
Standards Compliant. The Wireless Router complies with the IEEE802.11g (DSSS)
specifications for Wireless LANs.
Supports both 802.11b and 802.11g Wireless Stations. The 802.11g standard
provides for backward compatibility with the 802.11b standard, so both 802.11b and
802.11g Wireless stations can be used simultaneously.
Speeds to 54Mbps. All speeds up to the 802.11g maximum of 54Mbps are supported.
WEP support. Support for WEP (Wired Equivalent Privacy) is included. Key sizes of
64 Bit and 128 Bit are supported.
Wireless MAC Access Control. The Wireless Access Control feature can check the
the MAC address (hardware address) of Wireless stations to ensure that only trusted
Wireless Stations can access your LAN.
Simple Configuration. If the default settings are unsuitable, they can be changed
quickly and easily.
LAN Features
•
•
•
4-Port Switching Hub. The Wireless Router incorporates a 4-port 10/100BaseT
switching hub, making it easy to create or extend your LAN.
DHCP Server Support. Dynamic Host Configuration Protocol provides a dynamic IP
address to PCs and other devices upon request. The Wireless Router can act as a DHCP
Server for devices on your local LAN and WLAN.
Configuration & Management
•
Easy Setup.
•
Configuration File Upload/Download. Save (download) the configuration data from
•
Remote Management. The Wireless Router can be managed from any PC on your
•
Network Diagnostics. You can use the Wireless Router to perform a Ping or DNS
•
UPnP Support.
configuration.
Use your WEB browser from anywhere on the LAN or WLAN for
the Wireless Router to your PC, and restore (upload) a previously-saved configuration file
to the Wireless Router.
LAN. And, if the Internet connection exists, it can also (optionally) be configured via the
Internet.
lookup.
UPnP (Universal Plug and Play) allows automatic discovery and
configuration of the Wireless Router. UPnP is by supported by Windows ME, XP, or later.
Security Features
•
Password - protected Configuration. Optional password protection is provided to
•
Wireless LAN Security. WEP (Wired Equivalent Privacy) is supported, as well as
Wireless access control to prevent unknown wireless stations from accessing your LAN.
prevent unauthorized users from modifying the configuration data and settings.
•
NAT Protection. An intrinsic side effect of NAT (Network Address Translation)
•
Protection against DoS attacks. DoS (Denial of Service) attacks can flood your
technology is that by allowing all LAN users to share a single IP address, the location and
even the existence of each PC is hidden. From the external viewpoint, there is no network,
only a single device - the Wireless Router.
Internet connection with invalid packets and connection requests, using so much
bandwidth and so many resources that Internet access becomes unavailable. The Wireless
Router incorporates protection against DoS attacks.
Package Contents
The following items should be included:
•
•
•
•
The Wireless Router Unit
Power Adapter
Quick Installation Guide
CD-ROM containing the on-line manual.
If any of the above items are damaged or missing, please contact your dealer immediately.
Introduction
Physical Details
Front-mounted LEDs
Figure 1: Front Panel
Power LED
On - Power on.
Off - No power.
Internet LED
On - Connection to the Broadband Modem attached to the WAN
(Internet) port is established.
Off - No connection to the Broadband Modem.
Flashing - Data is being transmitted or received via the WAN port.
WLAN LED
On - Wireless connection available; Wireless Access Point is ready for
use.
Off - No Wireless connection available.
Flashing - Data is being transmitted or received via the Wireless access
point. Data includes "network traffic" as well as user data.
LAN LEDs
For each port, there are 2 LEDs
•
Link/Act
•
•
•
•
On - Corresponding LAN (hub) port is active.
Off - No active connection on the corresponding LAN (hub)
port.
Flashing - Data is being transmitted or received via the
corresponding LAN (hub) port.
100
•
•
On - Corresponding LAN (hub) port is using 100BaseT.
Off - Corresponding LAN (hub) port connection is using
10BaseT, or no active connection.
Rear Panel
Figure 2: Rear Panel
Power port
Connect the supplied power adapter here.
10/100BaseT
LAN port
Use standard LAN cables (RJ45 connectors) to connect your PCs to
these ports.
If required, any port can be connected to another hub. Any LAN port
will automatically function as an "Uplink" port when necessary.
Internet port
(10/100BaseT)
Connect the DSL or Cable Modem here. If your modem came with a
cable, use the supplied cable. Otherwise, use a standard LAN cable.
Reset Button
This button has two (2) functions:
•
•
Reboot. When pressed within 3~5 seconds, the power LED
lights amber then released, the Wireless Router will reboot
(restart).
Clear All Data. This button can also be used to clear ALL data
and restore ALL settings to the factory default values.
To Clear All Data and restore the factory default values:
1. After Power On.
2. Hold the Reset Button down.
3. Keep holding the Reset Button more than 5 seconds, until the
Amber LED has flashed.
4.
Release the Reset Button. The Wireless Router is now using the
factory default values.
Chapter 2 : I n s tal l ati o n
This Chapter covers the physical installation of the Wireless Router.
Requirements
•
•
•
•
Network cables. Use standard 10/100BaseT network (UTP) cables with RJ45 connectors.
TCP/IP protocol must be installed on all PCs.
For Internet Access, an Internet Access account with an ISP, and either of a DSL or
Cable modem (for WAN port usage)
To use the Wireless Access Point, all Wireless devices must be compliant with the
IEEE802.11b or IEEE802.11g specifications.
Procedure
1. Choose an Installation Site
Select a suitable place on the network to install the Wireless Router.
Ensure the Wireless Router and the DSL/Cable modem are powered OFF.
2. Connect LAN Cables
Use standard LAN cables to connect PCs to the Switching Hub ports on the Wireless
Router. Both 10BaseT and 100BaseT connections can be used simultaneously.
If required, connect any port to a normal port on another Hub, using a standard LAN
cable. Any LAN port on the Wireless Router will automatically function as an "Uplink"
port when required.
3. Connect WAN Cable
Connect the DSL or Cable modem to the WAN port on the Wireless Router. Use the cable
supplied with your DSL/Cable modem. If no cable was supplied, use a standard cable.
4. Power Up
•
•
Power on the Cable or DSL modem.
Connect the supplied power adapter to the Wireless Router and power up.
Use only the power adapter provided. Using a different one may cause hardware damage
5. Check the LEDs
•
•
•
•
•
The Power LED should be ON.
The Status LED should flash, then turn Off. If it stays on, there is a hardware error.
For each LAN (PC) connection, the LAN Link/Act LED should be ON (provided the PC
is also ON.)
The WAN LED should be ON.
The WLAN LED should be ON
For more information, refer to Front-mounted LEDs in Chapter 1.
Chapter 3 : S etu p
This Chapter provides Setup details of the Wireless Router.
Overview
This chapter describes the setup procedure for:
•
•
•
•
Internet Access
LAN configuration
Wireless setup
Assigning a Password to protect the configuration data.
PCs on your local LAN may also require configuration. For details, see Chapter 4 - PC
Configuration.
Other configuration may also be required, depending on which features and functions of the
Wireless Router you wish to use. Use the table below to locate detailed instructions for the
required functions.
Configuration Program
The Wireless Router contains an HTTP server. This enables you to connect to it, and
configure it, using your Web Browser. Your Browser must support JavaScript.
The configuration program has been tested on the following browsers:
•
•
Netscape V4.08 or later
Internet Explorer V4 or later
Preparation
Before attempting to configure the Wireless Router, please ensure that:
•
•
•
Your PC can establish a physical connection to the Wireless Router. The PC and the
Wireless Router must be directly connected (using the Hub ports on the Wireless Router)
or on the same LAN segment.
The Wireless Router must be installed and powered ON.
If the Wireless Router's default IP Address (192.168.1.254) is already used by another
device, the other device must be turned OFF until the Wireless Router is allocated a new
IP Address during configuration.
Using UPnP
If your Windows system supports UPnP, an icon for the Wireless Router will appear in the
system tray, notifying you that a new network device has been found, and offering to create a
new desktop shortcut to the newly-discovered device.
•
•
Unless you intend to change the IP Address of the Wireless Router, you can accept the
desktop shortcut.
Whether you accept the desktop shortcut or not, you can always find UPnP devices in My
Network Places (previously called Network Neighborhood).
•
Double - click the icon for the Wireless Router (either on the Desktop, or in My Network
Places) to start the configuration. Refer to the following section Setup Wizard for details
of the initial configuration process.
Using your Web Browser
To establish a connection from your PC to the Wireless Router:
1. After installing the Wireless Router in your LAN, start your PC. If your PC is already
running, restart it.
2. Start your WEB browser.
3. In the Address box, enter "HTTP://" and the IP Address of the Wireless Router, as in this
example, which uses the Wireless Router's default IP Address:
HTTP://192.168.1.254
Because the default password is blank, you will not be prompted for a password. However, you
should assign a password. See the Password Setup section later in this chapter for details.
If you can't connect
If the Wireless Router does not respond, check the following:
•
The Wireless Router is properly installed, LAN connection is OK, and it is
powered ON. You can test the connection by using the "Ping" command:
•
•
Open the MS-DOS window or command prompt window.
Enter the command:
ping 192.168.1.254
If no response is received, either the connection is not working, or your
PC's IP address is not compatible with the Wireless Router's IP Address.
(See next item.)
•
If your PC is using a fixed IP Address, its IP Address must be within the range
192.168.1.1 to 192.168.1.253 to be compatible with the Wireless Router's
default IP Address of 192.168.1.254. Also, the Network Mask must be set to
255.255.255.0. See Chapter 4 - PC Configuration for details on checking your
PC's TCP/IP settings.
•
Ensure that your PC and the Wireless Router are on the same network
segment. (If you don't have a router, this must be the case.)
•
Ensure you are using the wired LAN interface. The Wireless interface can
only be used if its configuration matches your PC's wireless settings.
10
Setup Wizard
The Setup Wizard provides brief and basic configuration of this device, you may enter each
screen to change the default settings. For more detailed settings, you may refer to the
“Configuration via Web” section.
1. View the listed configuration items and click Next to continue.
2. Configure Time Zone and NTP server by enabling NTP client update. Click Next to
continue.
3. Configure the parameters for area network (If you want to change the default parameter)
by entering New IP Address and Subnet Mask.
4. Change the access method (Static IP, DHCP, PPPoE or PPTP) by selecting for the pulldown menu. Click Next to continue.
11
5.
Configure the parameters for wireless LAN clients. Check the Disable Access Point to
disable the settings of this screen. Click Next to continue.
6. To manage your wireless network security by selecting the encryption type (None, WEP
and WPA (TKIP)) from the pull-down menu. Click Finish to exit Set Wizard screen.
Common Connection Types
Cable Modems
Type
Dynamic
IP Address
Details
Your IP Address is allocated
automatically, when you
connect to you ISP.
Static (Fixed)
IP Address
Your ISP allocates a
permanent IP Address to you.
ISP Data required
Usually, none.
However, some ISP's may
require you to use a particular
Hostname, Domain name, or
MAC (physical) address.
IP Address allocated to you.
Some ISP's may also require
you to use a particular
Hostname, Domain name, or
MAC (physical) address.
12
DSL Modems
Type
Details
ISP Data required
Dynamic
IP Address
Your IP Address is allocated
automatically, when you
connect to you ISP.
None.
Static (Fixed)
IP Address
Your ISP allocates a
permanent IP Address to you.
IP Address allocated to you.
PPPoE
You connect to the ISP only
when required. The IP address
is usually allocated
automatically.
User name and password.
PPTP
Mainly used in Europe.
•
You connect to the ISP only
when required. The IP address
is usually allocated
automatically, but may be
Static (Fixed).
•
•
PPTP Server IP Address.
User name and password.
IP Address allocated to
you, if Static (Fixed).
Other Modems (e.g. Broadband Wireless)
Type
Details
ISP Data required
Dynamic
IP Address
Your IP Address is allocated
automatically, when you
connect to you ISP.
None.
Static (Fixed)
IP Address
Your ISP allocates a permanent
IP Address to you.
IP Address allocated to you.
Configuration via Web
LAN Interface Setup
13
IP Address
Default: 192.168.1.254 (this is the local address of this
Router)
Subnet Mask
Default: 255.255.255.0
DHCP
Disable: Select to disable this Router to distribute IP
Addresses (Disabled)
Server: Select to enable this Router to distribute IP Addresses
(DHCP Server). And the following field will be activated for
you to enter the starting IP Address
DHCP Client Range
The starting address of this local IP network address pool.
The pool is a piece of continuous IP address segment. Keep
the default value 192.168.1.1 should work for most cases.
•
Maximum: 253. Default value 253 should work
for most cases.
Note: If “Continuous IP address poll starts” is set at
192.168.1.1 and the “Number of IP address in pool” is 253,
the device will distribute IP addresses from 192.168.1.1 to
192.168.1.253 to all the computers in the network that request
IP addresses from DHCP server (Router)
Show Client
Click to show Active DHCP Client table.
Save
After completing the settings on this page, click Save to save
the settings.
Reset
Click Reset to restore to default values.
14
Password Setup
New Password
Maximum input is 36 alphanumeric characters (case
sensitive)
Confirmed Password
Key in the password again to confirm.
Save
After completing the settings on this page, click Save to save
the settings.
Reset
Click Reset to clear settings.
Status
Internet
Shows the internet connection status
LAN
Shows the Local area network information
System
Briefly shows the device name and firmware information
Connection Details
Click to show more details of the internet connection
System Data
Click to show the detailed information of the system
Refresh Screen
Click to refresh all the data
15
Wireless Basic Settings
Disable Access Point
Check to disable the AP function.
The wireless (WLAN) LED on front panel will remain OFF if the
Wireless interface is disabled.
Band
You can choose one mode of the following you need.
 2.4GHz (B): 802.11b supported rate only.
 2.4GHz (G): 802.11g supported rate only.
 2.4GHz (B+G): 802.11b supported rate and 802.11g supported
rate.
The default is 2.4GHz (B+G) mode.
Network Type
Infrastructure: If set to Client (Infrastructure) mode, this device
can work like a wireless station when it’s connected to a computer
so that the computer can send packets from wired end to wireless
interface.
Ad hoc: If set to the Client (Ad-hoc) mode, this device can work
like a wireless station when it is connected to a computer so that
the computer can send packets from wired end to wireless
interface. You can share files and printers between wireless
stations (PC and laptop with wireless network adapter installed).
SSID
Shows the SSID name.
Channel Number
Select which channel to be located (from 1 to 11).
Associated Clients
Click to show all the listed active clients.
Save
After completing the settings on this page, click Save to save the
settings.
Reset
Click Reset to restore to default values.
16
Wireless Advanced Settings
Authentication Type
Open System If your access point/wireless router is using "Open
" authentication, then the wireless adapter will need to be set to the
same authentication type.
Shared Key: Shared Key is when both the sender and the
recipient share a secret key.
Auto: Select Auto Switch for the adapter to automatically select the
appropriate
Preamble Type
A preamble is a signal used in wireless environment to synchronize the
transmitting timing including Synchronization and Start frame delimiter.
(Note: If you want to change the Preamble type into Long or Short, please
check the setting of AP.)
Broadcast SSID
Enable: This wireless AP will broadcast its SSID to stations.
Disable: This wireless AP will not broadcast its SSID to stations. If stations
want to connect to this wireless AP, this AP’s SSID should be known in
advance to make a connection.
IAPP
IAPP (Inter Access Point Protocol) is designed for the enforcement
of unique association throughout a ESS (Extended Service Set) and
a secure exchange of station’s security context between current
access point (AP) and new AP during handoff period.
Enable: Clcik to enable the function.
Disable: Click to disable the function.
Save
After completing the settings on this page, click Save to save the
settings.
Reset
Click Reset to restore to default values.
17
Site Survey
Site survey displays all the active Access Points and IBSS in the neighborhood. When you are
in the client mode, you can select one AP to associate.
Click Refresh to get the latest information.
Security
Here you can configure the security of your wireless network. Selecting different method will
enable you to have different level of security. Please note that by using any encryption, by
which data packet is encrypted before transmission to prevent data packets from being
eavesdropped by unrelated people, there may be a significant degradation of the data
throughput on the wireless link.
Encryption: None (Encryption is set to None by default)
If Use 802.1x Authentication is selected, the RADIUS Server will proceed to check the
802.1x Authentication.
Encryption: WEP
If WEP is selected, users will have to Set WEP keys either manually, or select to Use 802.1x
Authentication to make the RADIUS server to issue the WEP key dynamically.
18
SET WEP KEY
Click the Set WEP Keys will prompt you a
window to set 64bit or 128bit Encryption.
Select HEX if you are using hexadecimal
numbers (0-9, or A-F). Select ASCII if you are
using ASCII characters (case-sensitive).
Ten hexadecimal digits or five ASCII
characters are needed if 64-bit WEP is used;
26 hexadecimal digits or 13 ASCII characters
are needed if 128-bit WEP is used.
Encryption: WPA (TKIP)
WPA (TKIP): If WPA is selected, users will have to select the Authentication modes
between Enterprise (RADIUS) and Personal (Pre-shared Key).
Pre-shared Key
Pre-Shared-Key serves as a password. Users may key in a 1
to 63 characters string to set the password or leave it blank,
in which the 802.1x Authentication will be activated. Make
sure the same password is used on client's end.
There are two formats for choice to set the Pre-shared key,
i.e. Passphrase and Hex. If Hex is selected, users will have
to enter a 64 characters string. For easier configuration, the
Passphrase (at least 8 characters) format is recommended.
Group Key Life Time
Enter the number of seconds that will elapse before the group
key change automatically. The default is 86400 seconds.
Enable PreAuthentication
The two most important features beyond WPA to become
standardized through 802.11i/WPA2 are: pre-authentication,
which enables secure fast roaming without noticeable signal
latency.
Preauthentication provides a way to establish a PMK security
association before a client associates. The advantage is that
the client reduces the time that it's disconnected to the
network.
Authentication RADIUS Port: Enter the RADIUS Server’s port number provided by
Server
your ISP. The default is 1812.
IP Address: Enter the RADIUS Server’s IP Address
provided by your ISP.
Password: Enter the password that the AP shares with the
19
RADIUS Server.
Save
Press to save the new settings on the screen.
Reset
Press to discard the current settings.
Wireless Trusted Stations
Wireless Access Control Mode
Select the Access Control Mode from the pull-down
menu.
Disable: Select to disable Wireless Access Control Mode.
Allow Listed: Only the stations shown in the table can
associate with the AP.
MAC Address
The Mac address of the station associated with the AP.
Description
You may key in a description for the MAC Address
Current Access Control List
Shows the current access control list.
Delete Selected
Select the MAC Address (es) you want to delete and then
click the Delete Selected button to delete the selected
items.
Delete All
Click to delete all the MAC Address (es) listed.
Save
After completing the settings on this page, click Save to
save the settings.
Reset
Click Reset to restore to default values.
20
Access Control
Enable Access Control
Select to enable Access Control function.
Select Services to Block
This lists all defined Services. Select the Services you wish to
block.
Port Range
For TCP and UDP Services, enter the beginning of the range
of port numbers used by the service. If the service uses a single
port number, enter it in both the start and finish fields.
Protocol
Select the protocol (TCP, UDP or Both) used to the remote
system or service.
Description
You may key in a description for port range.
Save
After completing the settings on this page, click Save to save
the settings.
Reset
Click Reset to restore to default values.
Dynamic DNS
21
Enable DDNS
Select to enable DDNS function.
This free service is very useful when combined with the Virtual
Server feature. It allows Internet users to connect to your Virtual
Servers using a URL, rather than an IP Address. This also solves
the problem of having a dynamic IP address. With a dynamic IP
address, your IP address may change whenever you connect, which
makes it difficult to connect to you.
Service Provider
•
•
•
•
Select the desired DDNS Service Provider from the list.
Details of your DDNS account (Name, password, Domain
name) must then be entered and saved on this screen.
This device will then automatically ensure that your current IP
Address is recorded by the DDNS Service Provider.
From the Internet, users will now be able to connect to your
Virtual Servers (or DMZ PC) using your Domain name.
Domain Name
•
User Name/Email
Enter your Username for the DDNS Service.
Password/key
Enter your current password for the DDNS Service.
Save
After completing the settings on this page, click Save to save the
settings.
Reset
Click Reset to restore to default values.
Apply for a Domain Name, and ensure it is allocated to you.
 Normally, this message should be "Update successful"
 If the message is "No host" or some other error message, you need to connect to the DDNS
Service provider and correct the problem.
DMZ
Enable DMZ
If the DMZ Host Function is enabled, it means that you set up
DMZ host at a particular computer to be exposed to the Internet
so that some applications/software, especially Internet / online
game can have two-way connections.
DMZ Host IP Address
Enter the IP address of a particular host in your LAN which will
receive all the packets originally going to the WAN port/Public IP
address above.
Note: You need to give your LAN PC clients a fixed/static IP
address for DMZ to work properly.
Save
After completing the settings on this page, click Save to save the
22
settings.
Reset
Click Reset to restore to default values.
Virtual Server
Enable Virtual Servers
Check to enable virtual server function.
Servers
You can set up a local server with specific port number that
stands for the service (e.g. web (80), FTP (21), Telnet (23)).
When this device receives an incoming access request for
this specific port, it will be forwarded to the corresponding
internal server. You can add virtual servers by either port
numbers or by names.
Maximum 24 Server entries are allowed and each port
number can only be assigned to one IP address.
Local IP Address
Enter the Local Server’s IP address.
Protocol
Select the protocol (TCP, UDP or Both) used to the remote system
or service.
Port Range
For TCP and UDP Services, enter the beginning of the range of
port numbers used by the service. If the service uses a single port
number, enter it in both the start and finish fields.
Description
You may key in a description for the local IP address.
Save
After completing the settings on this page, click Save to save the
settings.
Reset
Click Reset to restore to default values.
23
Special Application
If you use Internet applications that use non-standard connections or port numbers, you may
find that they do not function correctly because they are blocked by the Wireless Router's
firewall. In this case, you can define those applications as "Special Application" so that they
can function properly.
You can define your Special Applications. You will need detailed information about the
application such as number of port required; this is normally available from the supplier of the
application.
Also, note that "Incoming" on this screen refer to traffic from the client (PC) viewpoint.
You have to firstly check Enable before you can add/edit an application.
Name
Enter the application name.
Incoming Type
Click the down arrow  to select the incoming application type (TCP
or UDP)
Incoming Port
Range
Enter one or more set(s) of port number range as the incoming ports.
Once the trigger port is detected, the incoming packets are allowed to
pass the firewall to these already specified Incoming Ports.
Trigger Type
Click the down arrow  to select the trigger type (TCP or UDP)
Trigger Start
Port
Enter a port number as the starting outbound port for the special
application defined in the preceding field.
Trigger Finish
Port
Enter a port number as the ending outbound port for the special
application defined in the preceding field.
Save
Press to save the new settings on the screen.
Undo
Press to discard the data you have entered since last time you press
Save.
WAN Port
24
WAN Access Type
Select the WAN access type (Static IP, DHCP, PPPoE
and PPTP) from the pull-down menu.
DNS 1-3
Enter the DNS server IP address(es) provided by your
ISP, or you can specify your own preferred DNS server IP
address(es).
DNS 1 and DNS 2 servers are optional. You can enter
another DNS server’s IP address as a backup. DNS 1 and
DNS 2 servers will be used when the DNS 1 server fails.
Clone MAC Address
Your ISP may require a particular MAC address in order
for you to connect to the Internet. This MAC address is
the PC’s MAC address that your ISP had originally
connected your Internet connection to. Type in this Clone
MAC address in this section to replace the WAN MAC
address with the MAC address of that PC.
Enable uPNP
Check to enable the listed functions.
Enable Ipsec pass through
on VPN connection
Enable L2TP pass through
on VPN conenction
Save
After completing the settings on this page, click Save to
save the settings.
Reset
Click Reset to restore to default values.
Ping
This screen allows you to perform a "Ping". The response messages that will appear below
can be useful in diagnosing network problems.
25
IP Address/ Host Enter the IP address or domain name that you want to ping.
name
Run
Click to start pinging.
Reset
Click to clear the current IP address /Host name.
DoS Setting
A DoS (Denial of Service) attack does not attempt to steal data or damage your PCs, but
overloads your Internet connection so you cannot use it - the service is therefore unavailable.
If DoS function is enabled, DoS attacks will be detected and blocked. The default is unabled.
It is strongly recommended that this setting be left enabled.
Enable DoS
Prevention
Check to enable the DoS prevention function. Select the item listed to
enable.
Enable Source IP Set the threshold for the frequency of packets that are allowed to pass
Blocking Block through. The default value is 50 packets per seconds. You can adjust the
value according to your need. It is recommended that you set a practical
26
time (sec)
number so that your network performance won’t be hampered.
Selct All
Click to selct all listed items.
Clear All
Click to clear all listed items.
Apply Changes
Click to save the current settings.
Diagnostics
Remote management
The Wireless Router can be managed from any PC on your LAN. And, if the Internet
connection exists, it can also (optionally) be configured via the Internet.
Enable web Server Access via WAN
Check to enable the function.
Port number
Save
Click to save the current settings.
Reset
Click to clear the current settings.
Config File
This feature allows you to download the current settings from the Wireless Router, and save
them to a file on your PC.
You can restore a previously downloaded configuration file to the Wireless Router, by
uploading it to the Wireless Router.
27
This screen also allows you to set the Wireless Router back to its factory default configuration.
Any existing settings will be deleted.
An example Config File screen is shown below.
Backup Config
Use this to download a copy of the current configuration,
and store the file on your PC. Click Download to start the
download.
Restore Config
This allows you to restore a previously saved configuration
file back to the Wireless Router.
Click Browse to select the configuration file, then click
Restore to upload the configuration file.
WARNING !
Uploading a configuration file will destroy (overwrite) ALL
of the existing settings.
Default Config
Clicking the Restore Defaults button will reset the Wireless
Router to its factory default settings.
WARNING !
This will delete ALL of the existing settings.
Log
The Logs record various types of activity on the Wireless Router. This data is useful for
troubleshooting, but enabling all logs will generate a large amount of data and adversely affect
performance.
28
Enable Log
Click to enable log function.
Enable Remote Log
Click to enable the remote log function. The log record will be
saved into a remote server.
System all:
Wireless only:
Dos only:
Save
After completing the settings on this page, click Save to save the
settings.
Refresh
Click to refresh the logs.
Clear
Click to delete the logs.
IP Filtering
Enable IP Filtering
Check to enable the IP filtering function.
Local IP Address
Enter the client IP address.
Protocol
Select the protocol (TCP, UDP or Both) used to the remote system
or service.
Description
You may key in a description for the local IP address
Current Filter Table
Shows the current filter information.
Save
After completing the settings on this page, click Save to save the
settings.
Reset
Click Reset to restore to default values.
29
MAC Filtering
Enable MAC
Filtering
Check to enable MAC filtering function.
MAC Address
Enter the client MAC address.
Description
You may key in a description for the MAC address.
Current Filter Table
Shows the current filter information.
Save
After completing the settings on this page, click Save to save the
settings.
Reset
Click Reset to restore to default values.
Statistics
Refresh
Click to refresh the statistics table.
30
Time Zone Setting
Current Time
Enter the current time of this wireless router.
Enable NTP client
update
Check to enable NTP (Network Time Protocol Server) client update
function.
Time Zone Select
Select the time zone from the pull-down menu.
NTP server
You may choose to select NTP server from the pull-down menu or
enter an IP address of a specific server.
Save
After completing the settings on this page, click Save to save
the settings.
Reset
Click Reset to restore to default values.
Refresh
Click to refresh the current time.
Upgrade Firmware
31
Browse
Click the Browse button, find and open the firmware file (the
browser will display to correct file path).
Start Upgrade
Click the Start Upgrade button to perform
Reset
Click Reset to restore to default values.
Navigation & Data Input
•
•
Use the menu bar on the left of the screen, and the "Back" button on your Browser, for
navigation.
Changing to another screen without clicking "Save" does NOT save any changes you may
have made. You must "Save" before changing screens or your data will be ignored.
32
Chapter 4 : P C Co n f i g u rati o n
Overview
For each PC, the following may need to be configured:
•
•
•
TCP/IP network settings
Internet Access configuration
Wireless configuration
Windows Clients
This section describes how to configure Windows clients for Internet access via the Wireless
Router.
The first step is to check the PC's TCP/IP settings.
The Wireless Router uses the TCP/IP network protocol for all functions, so it is essential that
the TCP/IP protocol be installed and configured on each PC.
TCP/IP Settings - Overview
If using the default Wireless Router settings, and the default Windows
TCP/IP settings, no changes need to be made.
•
•
By default, the Wireless Router will act as a DHCP Server, automatically providing a
suitable IP Address (and related information) to each PC when the PC boots.
For all non-Server versions of Windows, the default TCP/IP setting is to act as a DHCP
client.
If using a Fixed (specified) IP address, the following changes are
required:
•
•
The Gateway must be set to the IP address of the Wireless Router
The DNS should be set to the address provided by your ISP.
33
Checking TCP/IP Settings - Windows 98/ME:
1.
Select Control Panel - Network. You should see a screen like the following:
2.
3.
Select the TCP/IP protocol for your network card.
Click on the Properties button. You should then see a screen like the following.
Ensure your TCP/IP settings are correct, as follows:
Using DHCP
To use DHCP, select the radio button Obtain an IP Address automatically. This is the default
Windows setting. Using this is recommended. By default, the Wireless Router will act as a
DHCP Server.
Restart your PC to ensure it obtains an IP Address from the Wireless Router.
Using "Specify an IP Address"
If your PC is already configured, check with your network administrator before making the
following changes:
•
On the Gateway tab, enter the Wireless Router's IP address in the New Gateway field and
click Add, as shown below. Your LAN administrator can advise you of the IP Address
they assigned to the Wireless Router.
34
•
On the DNS Configuration tab, ensure Enable DNS is selected. If the DNS Server Search
Order list is empty, enter the DNS address provided by your ISP in the fields beside the
Add button, then click Add.
35
Checking TCP/IP Settings - Windows NT4.0
1.
Select Control Panel - Network, and, on the Protocols tab, select the TCP/IP protocol, as
shown below.
2.
Click the Properties button to see a screen like the one below.
36
3.
4.
Select the network card for your LAN.
Select the appropriate radio button - Obtain an IP address from a DHCP Server or
Specify an IP Address, as explained below.
Obtain an IP address from a DHCP Server
This is the default Windows setting. Using this is recommended. By default, the Wireless
Router will act as a DHCP Server.
Restart your PC to ensure it obtains an IP Address from the Wireless Router.
Specify an IP Address
If your PC is already configured, check with your network administrator before making the
following changes.
1.
The Default Gateway must be set to the IP address of the Wireless Router. To set this:
•
•
•
Click the Advanced button on the screen above.
On the following screen, click the Add button in the Gateways panel, and enter the
Wireless Router's IP address.
If necessary, use the Up button to make the Wireless Router the first entry in the
Gateways list.
37
2.
The DNS should be set to the address provided by your ISP, as follows:
•
•
Click the DNS tab.
On the DNS screen, shown below, click the Add button (under DNS Service Search
Order), and enter the DNS provided by your ISP.
38
39
Checking TCP/IP Settings - Windows 2000:
1.
2.
Select Control Panel - Network and Dial-up Connection.
Right - click the Local Area Connection icon and select Properties. You should see a
screen like the following:
3.
4.
Select the TCP/IP protocol for your network card.
Click on the Properties button. You should then see a screen like the following.
40
5.
Ensure your TCP/IP settings are correct, as described below.
Using DHCP
To use DHCP, select the radio button Obtain an IP Address automatically. This is the default
Windows setting. Using this is recommended. By default, the Wireless Router will act as a
DHCP Server.
Restart your PC to ensure it obtains an IP Address from the Wireless Router.
Using a fixed IP Address ("Use the following IP Address")
If your PC is already configured, check with your network administrator before making the
following changes.
•
•
Enter the Wireless Router's IP address in the Default gateway field and click OK. (Your
LAN administrator can advise you of the IP Address they assigned to the Wireless Router.)
If the DNS Server fields are empty, select Use the following DNS server addresses, and
enter the DNS address or addresses provided by your ISP, then click OK.
41
Checking TCP/IP Settings - Windows XP
1.
2.
Select Control Panel - Network Connection.
Right click the Local Area Connection and choose Properties. You should see a screen
like the following:
3.
4.
Select the TCP/IP protocol for your network card.
Click on the Properties button. You should then see a screen like the following.
42
5.
Ensure your TCP/IP settings are correct.
Using DHCP
To use DHCP, select the radio button Obtain an IP Address automatically. This is the default
Windows setting. Using this is recommended. By default, the Wireless Router will act as a
DHCP Server.
Restart your PC to ensure it obtains an IP Address from the Wireless Router.
Using a fixed IP Address ("Use the following IP Address")
If your PC is already configured, check with your network administrator before making the
following changes.
•
•
In the Default gateway field, enter the Wireless Router's IP address and click OK. Your
LAN administrator can advise you of the IP Address they assigned to the Wireless Router.
If the DNS Server fields are empty, select Use the following DNS server addresses, and
enter the DNS address or addresses provided by your ISP, then click OK.
43
Internet Access
To configure your PCs to use the Wireless Router for Internet access:
•
•
Ensure that the DSL modem, Cable modem, or other permanent connection is functional.
Use the following procedure to configure your Browser to access the Internet via the LAN,
rather than by a Dial-up connection.
For Windows 9x/ME/2000
1.
2.
3.
4.
5.
6.
7.
Select Start Menu - Settings - Control Panel - Internet Options.
Select the Connection tab, and click the Setup button.
Select "I want to set up my Internet connection manually, or I want to connect through a
local area network (LAN)" and click Next.
Select "I connect through a local area network (LAN)" and click Next.
Ensure all of the boxes on the following Local area network Internet Configuration screen
are unchecked.
Check the "No" option when prompted "Do you want to set up an Internet mail account
now?".
Click Finish to close the Internet Connection Wizard.
Setup is now completed.
For Windows XP
1.
2.
3.
4.
5.
6.
7.
8.
9.
Select Start Menu - Control Panel - Network and Internet Connections.
Select Set up or change your Internet Connection.
Select the Connection tab, and click the Setup button.
Cancel the pop-up "Location Information" screen.
Click Next on the "New Connection Wizard" screen.
Select "Connect to the Internet" and click Next.
Select "Set up my connection manually" and click Next.
Check "Connect using a broadband connection that is always on" and click Next.
Click Finish to close the New Connection Wizard.
Setup is now completed.
Accessing AOL
To access AOL (America On Line) through the Wireless Router, the AOL for Windows
software must be configured to use TCP/IP network access, rather than a dial-up connection.
The configuration process is as follows:
•
•
•
•
•
•
Start the AOL for Windows communication software. Ensure that it is Version 2.5, 3.0 or
later. This procedure will not work with earlier versions.
Click the Setup button.
Select Create Location, and change the location name from "New Locality" to "Wireless
Router".
Click Edit Location. Select TCP/IP for the Network field. (Leave the Phone Number
blank.)
Click Save, then OK.
Configuration is now complete.
Before clicking "Sign On", always ensure that you are using the "Wireless Router"
location.
44
Macintosh Clients
From your Macintosh, you can access the Internet via the Wireless Router. The procedure is
as follows.
1. Open the TCP/IP Control Panel.
2. Select Ethernet from the Connect via pop-up menu.
3. Select Using DHCP Server from the Configure pop-up menu. The DHCP Client ID field
can be left blank.
4. Close the TCP/IP panel, saving your settings.
Note:
If using manually assigned IP addresses instead of DHCP, the required changes are:
•
•
Set the Router Address field to the Wireless Router's IP Address.
Ensure your DNS settings are correct.
Linux Clients
To access the Internet via the Wireless Router, it is only necessary to set the Wireless Router
as the "Gateway".
Ensure you are logged in as "root" before attempting any changes.
Fixed IP Address
By default, most Unix installations use a fixed IP Address. If you wish to continue using a
fixed IP Address, make the following changes to your configuration.
•
•
Set your "Default Gateway" to the IP Address of the Wireless Router.
Ensure your DNS (Name server) settings are correct.
To act as a DHCP Client (recommended)
The procedure below may vary according to your version of Linux and X -windows shell.
1. Start your X Windows client.
2. Select Control Panel - Network
3. Select the "Interface" entry for your Network card. Normally, this will be called "eth0".
4. Click the Edit button, set the "protocol" to "DHCP", and save this data.
5. To apply your changes
•
•
Use the "Deactivate" and "Activate" buttons, if available.
OR, restart your system.
Other Unix Systems
To access the Internet via the Wireless Router:
• Ensure the "Gateway" field for your network card is set to the IP Address of the Wireless
Router.
•
Ensure your DNS (Name Server) settings are correct.
45
Wireless Station Configuration
This section applies to all Wireless stations wishing to use the Wireless Router's Access Point,
regardless of the operating system which is used on the client.
To use the Wireless Access Point in the Wireless Router, each Wireless Station must have
compatible settings, as follows:
Mode
The mode must be set to Infrastructure.
SSID (ESSID)
This must match the value used on the Wireless Router. The default
value is Untitled
Note! The SSID is case sensitive.
WEP
By default, WEP on the Wireless Router is disabled.
•
•
If WEP remains disabled on the Wireless Router, all stations must
have WEP disabled.
If WEP is enabled on the Wireless Router, each station must use the
same settings as the Wireless Router.
Note:
By default, the Wireless Router will allow both 802.11b and 802.11g connections.
46
Appendix A
T ro u b l es ho o ti n g
This Appendix covers the most likely problems and their solutions.
Overview
This chapter covers some common problems that may be encountered while using the
Wireless Router and some possible solutions to them. If you follow the suggested steps and the
Wireless Router still does not function properly, contact your dealer for further advice.
General Problems
Problem 1:
Can't connect to the Wireless Router to configure it.
Solution 1:
Check the following:
•
•
•
•
The Wireless Router is properly installed, LAN connections are OK,
and it is powered ON.
Ensure that your PC and the Wireless Router are on the same network
segment. (If you don't have a router, this must be the case.)
If your PC is set to "Obtain an IP Address automatically" (DHCP
client), restart it.
If your PC uses a Fixed (Static) IP address, ensure that it is using an IP
Address within the range 192.168.1.1 to 192.168.1.253 and thus
compatible with the Wireless Router's default IP Address of
192.168.1.254.
Also, the Network Mask should be set to 255.255.255.0 to match the
Wireless Router.
In Windows, you can check these settings by using Control PanelNetwork to check the Properties for the TCP/IP protocol.
Internet Access
Problem 1:
When I enter a URL or IP address I get a time out error.
Solution 1:
A number of things could be causing this. Try the following
troubleshooting steps.
•
•
•
Problem 2:
Check if other PCs work. If they do, ensure that your PCs IP settings
are correct. If using a Fixed (Static) IP Address, check the Network
Mask, Default gateway and DNS as well as the IP Address.
If the PCs are configured correctly, but still not working, check the
Wireless Router. Ensure that it is connected and ON. Connect to it and
check its settings. (If you can't connect to it, check the LAN and power
connections.)
If the Wireless Router is configured correctly, check your Internet
connection (DSL/Cable modem etc) to see that it is working correctly.
Some applications do not run properly when using the Wireless Router.
Solution 2:
The Wireless Router processes the data passing through it, so it is not
transparent.
Use the Special Applications feature to allow the use of Internet
applications which do not function correctly.
If this does solve the problem you can use the DMZ function. This should
work with almost every application, but:
• It is a security risk, since the firewall is disabled.
• Only one (1) PC can use this feature.
Wireless Access
Problem 1:
My PC can't locate the Wireless Access Point.
Solution 1:
Check the following.
•
•
•
•
•
•
Your PC is set to Infrastructure Mode. (Access Points are always in
Infrastructure Mode)
The SSID on your PC and the Wireless Access Point are the same.
Remember that the SSID is case-sensitive. So, for example
"Workgroup" does NOT match "workgroup".
Both your PC and the Wireless Router must have the same setting for
WEP. The default setting for the Wireless Router is disabled, so your
wireless station should also have WEP disabled.
If WEP is enabled on the Wireless Router, your PC must have WEP
enabled, and the key must match.
If the Wireless Router's Wireless screen is set to Allow LAN access to
selected Wireless Stations only, then each of your Wireless stations
must have been selected, or access will be blocked.
To see if radio interference is causing a problem, see if connection is
possible
when
close
to
the
Wireless
Router.
Remember that the connection range can be as little as 100 feet in poor
environments.
Problem 2:
Wireless connection speed is very slow.
Solution 2:
The wireless system will connect at the highest possible speed, depending
on the distance and the environment. To obtain the highest possible
connection speed, you can experiment with the following:
•
•
•
•
Wireless Router location.
Try adjusting the location and orientation of the Wireless Router.
Wireless Channel
If interference is the problem, changing to another channel may show a
marked improvement.
Radio Interference
Other devices may be causing interference. You can experiment by
switching other devices Off, and see if this helps. Any "noisy" devices
should be shielded or relocated.
RF Shielding
Your environment may tend to block transmission between the wireless
stations. This will mean high access speed is only possible when close
to the Wireless Router.
48
Appendix B
A b o u t W i rel es s L A N s
This Appendix provides some background information about using Wireless
LANs (WLANs).
Modes
Wireless LANs can work in either of two (2) modes:
•
•
Ad-hoc
Infrastructure
Ad-hoc Mode
Ad-hoc mode does not require an Access Point or a wired (Ethernet) LAN. Wireless
Stations (e.g. notebook PCs with wireless cards) communicate directly with each other.
Infrastructure Mode
In Infrastructure Mode, one or more Access Points are used to connect Wireless Stations
(e.g. Notebook PCs with wireless cards) to a wired (Ethernet) LAN. The Wireless Stations
can then access all LAN resources.
Access Points can only function in "Infrastructure" mode,
and can communicate only with Wireless Stations which are
set to "Infrastructure" mode.
BSS
BSS
A group of Wireless Stations and a single Access Point, all using the same ID (SSID), form a
Basic Service Set (BSS).
Using the same SSID is essential. Devices with different SSIDs are unable to communicate
with each other.
Channels
The Wireless Channel sets the radio frequency used for communication.
•
•
Access Points use a fixed Channel. You can select the Channel used. This allows you to
choose a Channel which provides the least interference and best performance. In the USA
and Canada, 11 channel are available. If using multiple Access Points, it is better if
adjacent Access Points use different Channels to reduce interference.
In "Infrastructure" mode, Wireless Stations normally scan all Channels, looking for an
Access Point. If more than one Access Point can be used, the one with the strongest
signal is used. (This can only happen within an ESS.)
WEP
WEP (Wired Equivalent Privacy) is a standard for encrypting data before it is transmitted.
This is desirable because it is impossible to prevent snoopers from receiving any data which is
transmitted by your Wireless Stations. But if the data is encrypted, then it is meaningless
unless the receiver can decrypt it.
If WEP is used, the Wireless Stations and the Access Point must have the same settings
for each of the following:
WEP
Off, 64 Bit, 128 Bit
Key
For 64 Bit encryption, the Key value must match.
For 128 Bit encryption, the Key value must match
WEP Authentication
Open System or Shared Key.
Wireless LAN Configuration
To allow Wireless Stations to use the Access Point, the Wireless Stations and the Access Point
must use the same settings, as follows:
Mode
On client Wireless Stations, the mode must be set to "Infrastructure".
(The Access Point is always in "Infrastructure" mode.)
SSID (ESSID)
Wireless Stations should use the same SSID (ESSID) as the Access
Point they wish to connect to. Alternatively, the SSID can be set to
"any" or null (blank) to allow connection to any Access Point.
WEP
The Wireless Stations and the Access Point must use the same settings
for WEP (Off, 64 Bit, 128 Bit).
WEP Key: If WEP is enabled, the Key must be the same on the
Wireless Stations and the Access Point.
WEP Authentication: If WEP is enabled, all Wireless Stations must
use the same setting as the Access Point (either "Open System" or
"Shared Key").
50
A ppen d i x C
S pec i f i c ati o n s
Multi-Function Wireless Router
Model
Wireless Router
Dimensions
141mm(W) * 100mm(D) * 27mm(H)
Operating Temperature
0° C to 40° C
Storage Temperature
-10° C to 70° C
Network Protocol:
TCP/IP
Network Interface:
5 Ethernet:
4 * 10/100BaseT (RJ45) LAN connection
1 * 10/100BaseT (RJ45) for WAN
LEDs
12
Power Adapter
12 V DC External
Wireless Interface
Standards
IEEE802.11g WLAN, JEIDA 4.2, roaming support
Frequency
2.4 to 2.4835GHz (Industrial Scientific Medical Band )
Channels
Maximum 14 Channels, depending on regulatory authorities
Modulation
DSSS BPSK/QPSK/CCK, OFDM/CCK
Data Rate
Up to 54 Mbps
Coverage Area
Indoors : 15m @54Mbps, 120m @6Mbps or lower
Outdoors : 40m @54Mbps, 300m @6Mbps or lower
WEP
64Bit, 128Bit
Output Power (Peak)
1802.11B
802.11b:19.04dBm;802.11g:18.73dBm
Receiver Sensitivity
-80dBm Min.
Regulatory Approvals
CE Standards
This product complies with the 99/5/EEC directives, including the following safety and EMC
standards:
•
•
•
EN300328-2
EN301489-1/-17
EN60950
CE Marking Warning
This is a Class B product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.
52
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one of the
following measures:
● Reorient or relocate the receiving antenna.
● Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
●
Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the
party responsible for compliance could void the user’s authority to operate this
equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference,
and (2) this device must accept any interference received, including
interference that may cause undesired operation.
This device and its antenna(s) must not be co-located or operation in
conjunction with any other antenna or transmitter.
●
IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated
with minimum distance 20cm between the radiator & your body.
For product available in the USA/Canada market, only channel 1~11 can be
operated. Selection of other channels is not possible.
CE Statement
Hereby, ZyXEL, declares that this device is in compliance with the essential
requirement and other relevant provisions of the R&TTE Driective 1999/5/EC.
IC Statement
The Class B digital appartus complies with Canadian ICES-003.
Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause
undesired operation of the device.

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Encryption                      : Standard V2.3 (128-bit)
User Access                     : Print, Extract, Print high-res
XMP Toolkit                     : 3.1-701
Modify Date                     : 2007:07:27 13:29:37+08:00
Create Date                     : 2007:06:07 11:35:43+08:00
Metadata Date                   : 2007:07:27 13:29:37+08:00
Creator Tool                    : PScript5.dll Version 5.2
Format                          : application/pdf
Title                           : Microsoft Word - WR254MNL-1.DOC
Creator                         : ken
Document ID                     : uuid:3b45d128-c56c-406f-8e8a-cedf7e8a28c7
Instance ID                     : uuid:46abe071-e27f-4292-95ab-6515a8267450
Producer                        : GNU Ghostscript 7.06
Has XFA                         : No
Page Count                      : 55
Author                          : ken
EXIF Metadata provided by EXIF.tools
FCC ID Filing: I88P330W

Navigation menu