ZyXEL Communications P664HNT1 802.11n Dual ADSL 2+ 4-port Gateway User Manual

ZyXEL Communications Corporation 802.11n Dual ADSL 2+ 4-port Gateway

User Manual

P-664HN-T1802.11nDualADSL 2+4-portGatewayQuick StartGuideVersion 3.408/2010Edition 1
P-664HN-T1 Quick Start GuideOverviewThe P-664HN-T1 is a 802.11n Dual ADSL2+ 4-port Gateway with a four-port built-inswitch.This Quick Start Guide shows you how to use the P-664HN-T1 to connect to the Internet andhow to configure the device settings to connect wirelessly.See your User’s Guide for background information on all features.Quick Login InformationLAN IP addresshttp://192.168.1.1default administrator password12342
P-664HN-T1 Quick Start Guide1HardwareConnections1 DSL: Use the gray telephone wire to connect your P-664HN-T1’s DSL port to telephone jack (or tothe modem port on a splitter if you are using one).2 ETHERNET: Use the yellow Ethernet cable to connect a computer to an ETHERNET port forinitial configuration and/or Internet access.3 POWER: Use the included power adaptor to connect an appropriate power source to the POWER socket.Make sure the power source is on.4Push in the POWER button.5Look at the lights on the front panel.• The POWER light blinks while your P-664HN-T1 starts up and stays on once it is ready.• Each ETHERNET light stays on if the corresponding ETHERNET port is properly connected and blinkswhen there is traffic.• The DSL light is on when the P-664HN-T1 has a DSL connection.• The INTERNET light is on when you are able to access the Internet and blinks when the P-664HN-T1is sending or receiving data. Wait a couple of minutes while your device checks the connection.If any of these lights are not on, check your connections and inspect your cables for damage. If the lightsare still off, contact your local vendor.2Internet ConnectionSetup: AutomaticUse this section to have your P-664HN-T1 automatically detect and set up your Internet connection.1Open your web browser to a website. W ait while your P-664HN-T1 tries to detect your DSL connection toyourISP. This may take a few minutes.2After it detects the connection, the DSL light shows green on your device and the Internet light comes onwhen the Internet is ready for you to use. If you have a PPPoE connection, you will have to enter youruser name and password.3Go to section 3if you wish to configure your wireless settings.4If you do not see the connection test screen, or the connection test is not successful , follow thei nstructions i n the screen below, or check your connections and restart the P-664HN-T1. If you stillcannot access the Internet, follow the steps in section 3.3Configuring your WirelessSettingsTo create a wireless network, the P-664HN-T1 and your wireless computer must all use the sameSSID (network name), channel and security settings.If you do not set wireless security then anyone within range could use your P-664HN-T1 to accessyour network and the Internet.Choose W PA-PSK wireless security if your wireless device supports it as it is stronger than W EP. Otherwisechoose W EP.3
P-664HN-T1 Quick Start Guide1Select Active and click Next to continue. It is strongly recommended that Enable OTIST is NOT selected.Seesection7for more information.2Configure your wireless settings in the screen. Click Next.3) If you select either WEP or WPA-PSK security (recommended), then follow the directions to enterthe appropriate key. Click Next to continue and Apply to save your wireless LAN settings.4Check your configuration and write down your wireless LAN settings for later use. Click Finish to complete andsave the wizard setup.5Your Internet is ready for you to use. Open your browser and navigate to your favorite website.4Internet ConnectionSetup UsingAdvancedSettingsUse this section to set up your Internet connection manually if you do not see the ISP Parameters for InternetAccess screen when you run the wizard (see section 4, step 4).1Login again. (Follow steps 1to 5in section 3.)2Select Go to Advanced setup. Then, click Apply.3The Status screen appears. Click Network >WAN in the navigation panel on the left of the screen.4Enter the information exactly as provided by your ISP. Click Apply.5If you still cannot access the Internet, see Troubleshooting and/or contact your Internet Service Provider(ISP) for assistance.4
P-664HN-T1 Quick Start GuideTroubleshooting1If you cannot access the web configurator,• Your computer may be set to use a static IP address in a different subnet from the ZyXEL device. See theappendix in the User’s Guide for information on setting up your IP address.• If you are using Internet Explorer in W indows XP or W indows Server 2003, make sure you allow pop-upwindows, JavaScripts and Java permissions or set the Internet security level lower than High in InternetExplorer (in Internet Explorer, click Tools > Internet Options > Security > Custom Level...). See theappendix in the User’s Guide for more information.2If you cannot access the Internet when your computer is connected to the ETHERNET port, follow thesesteps.A) Check the lights on the front panel. If they are different from what is described in section 1, make surethe P-664HN-T1 is correctly connected. (See section 1.) If the lights are still different, turn off thedevice, wait a few seconds, and turn it on again.B) Check you have correctly entered the informatinon your ISP gave you. For example, if your account hasa user name and password, make sure you type it correctly. In addition, if you are not sure whichencapsulation your ISP uses, contact your ISP. If your ISP did not give you Internet connectioninformation, follow the steps in section 2.C) If you are using a new Internet account, contact your ISP to make sure it is active.D) If you still have problems, see Troubleshooting in the User’s Guide.If you cannot access the Internet after you take the steps above, either try the following or contact your ISP:E) Turn your P-664HN-T1 off and on. Open your Internet browser if it is not already open.Let the P-664HN-T1 complete the DSL connection test (this may take several minutes). See section 2for details.If the test is successful, check whether you can access the Internet.F) If the test is unsuccessful or if you cannot access the Internet, log in to the P-664HN-T1’sweb configurator (see section 3).• Click Network >WAN >Internet Connection. Ensure that the settings i n this screen are the sam e asthose your ISP gave you. If your ISP gave you a stati c IP address to use, select Static IP Address inthe IP Address section and enter it i n the IP Address field. If not, sel ect Obtain an IP Address Auto-matically. Click Apply.• Click the wizard icon ( ). Run the Internet/Wireless Setup wizard again. Check whether you canaccess the Internet.If you still cannot access the Internet, take the following steps:• If you are using Bridge mode (check Mode in the Network >WAN >Internet Connection screen) clickNAT >General and ensure Active Network Address Translation (NAT) is not selected. Click LAN >DHCP Setup and ensure that DHCP is set to None. Your ISP gives your computer an IP addressdirectly. If you want to access the P-664HN-T1 again, you need to use a static IP address in the samesubnet as your P-664HN-T1 (the P-664HN-T1’s default IP address is http://192.168.1.1).• Click the wizard icon ( ). Run the Internet/Wireless Setup wizard again. Check whether you canaccess the Internet.If you still cannot access the Internet, contact your Internet Service Provider.5
P-664HN-T1 Quick Start Guide3If you cannot access the Internet using the wireless network, follow these steps.A) On a computer in the wireless network, open your browser, and go to http://192.168.1.1. If you see thelogin screen in section 3, follow suggestions A-Fabove. If you do not, go to the next step.B) On a computer connected to the P-664HN-T1, make sure your P-664HN-T1 and the computerson your wireless network are using the same wireless and wireless security settings. See thechapter on W ireless LAN in the User’s Guide for more information.Viewing YourProduct’sCertifications1Go to www.zyxel.com.2Select your product from the drop-down list box on the ZyXEL home page to go to that product's page.3Select the certification you wish to view from this page.Customer InformationStatementThe information informing the user of his/her and the telephone company's rights and obligations is outlinedon the following pages. This information will be included in the final version of the manual.Customer Information1This equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA. Onbottom of this equipment is a label that contains, among other information, a product identifier of P-664HN-T1. If requested, this number must be provided to the telephone company.2If this equipment DL causes harm to the telephone network, the telephone com pany will notify you inadvance that temporary discontinuance of service may be required. But if advance notice isn't practical,the telephone company will notify the customer as soon as possible. Also you will be advised of your rightto file a complaint with the FCC if you believe it is necessary.3The telephone company may make changes in its facilities, equipment, operations or procedures thatcould affect the operation of the equipm ent. If this happens, the telephone company will provide advancenotice in order for you to make necessary modification to maintain uninterrupted service.4If you experience trouble with this equipment, you disconnect it from the network until the problem hasbeen corrected or until you are sure that the equipment is not malfunctioning.5Please follow instructions for repairing if any (e.g. battery replacement section); otherwise do not alternateor repair any parts of device except specified.6Connection to party line service is subject to state tariffs. Contact the state public utility commission, publicservice commission or corporation commission for information.6
P-664HN-T1 Quick Start Guide7If your home has specially wired alarm equipment connected to the telephone line, ensure the installationof this equipment does not disable alarm equipment, consult your telephone company or a qualifiedinstaller.Service RequirementsIn the event of equipment malfunction, all repairs should be performed by our Company or an authorizedagent. It is the responsibility of users requiring service to report the need for service to our Company or to oneof our authorized agents.Service can be facilitated through our office at:ZyXEL Communications Corporation6, Innovation Rd II, Science-Based Industrial Park, Hsin-Chu, Taiwan, R.O.C.+886- 3-578-3942CertificationsFederal Communications Commission (FCC) Interference StatementThe device complies with Part 15 of FCC rules. Operation is subject to thefollowing two conditions:• This device may not cause harmful interference.• This device must accept any interference received, including interference thatmay cause undesired operations.This device has been tested and found to comply with the limits for a Class Bdigital device pursuant to Part 15 of the FCC Rules. These limits are designed toprovide reasonable protection against harmful interference in a residentialinstallation. This device generates, uses, and can radiate radio frequency energy,and if not installed and used in accordance with the instructions, may causeharmful interference to radiocommunications.However, there is no guaranteethat interference will not occur in a particular installation.If this device does cause harmful interference to radio/television reception, whichcan be determined by turning the device off and on, the user is encouraged to tryto correct the interference by one or more of the following measures:1Reorient or relocate the receiving antenna.2Increase the separation between the equipment and the receiver.3Connect the equipment into an outlet on a circuit different from that to which thereceiver is connected.4Consult the dealer or an experienced radio/TV technician for help.7
P-664HN-T1 Quick Start GuideFCC Radiation Exposure Statement• This transmitter must not be co-located or operating in conjunction with anyother antenna or transmitter.• IEEE 802.11b or 802.11g or 802.11n(20MHz) operation of this product in theU.S.A. is firmware-limited to channels 1 through 11. 802.11n(40MHz)operation of this product in the U.S.A. is firmware-limited to channels 3through 9.• To comply with FCC RF exposure compliancerequirements,a separationdistance of at least 20 cm must be maintained between the antenna of thisdevice and all persons.Safety Warnings• Do NOT use this product near water, for example, in a wet basement or near aswimming pool.• Do NOT expose your device to dampness, dust or corrosiveliquids.• Do  NOT store  things on  thedevice.• Do NOT install, use, or service this device during a thunderstorm. There is aremote risk of electric shock from lightning.• Connect ONLY  suitable  accessories to thedevice.• Do NOT open the device or unit. Opening or removing covers can expose youto dangerous high voltage points or other risks. ONLY qualified servicepersonnel should service or disassemble this device. Please contact yourvendor for further information.• Make  sure  to  connect  the  cables  to  thecorrect ports.• Place  connecting  cables  carefully  so  that no  one  will  step on  them or  stumbleover them.• Always  disconnect  all  cables  from  this  device  before  servicing ordisassembling.• Use ONLY an appropriate power adaptor or cord for yourdevice.• Connect  the  power  adaptor  or  cord  to the  right  supply voltage  (for  example,110V AC in North America or 230V AC in Europe).• Do NOT allow anything to rest on the power adaptor or cord and do NOTplace the product where anyone can walk on the power adaptor or cord.• Do NOT use the device if the power adaptor or cord is damaged as itmight cause electrocution.8
P-664HN-T1 Quick Start Guide• If the power adaptor or cord is damaged, remove it from the device and thepower source.• Do NOT attempt to repair the power adaptor or cord. Contact your local vendor toorder a new one.• Do not use the device outside, and make sure all the connections are indoors.There is a remote risk of electric shock from lightning.• Do NOT obstruct the device ventilation slots, as insufficient airflow mayharm your device.• Use only  No. 26 AWG  (American  Wire  Gauge)  or  larger  telecommunicationline cord.• Antenna Warning! This device meets ETSI and FCC certification requirementswhen using the included antenna(s). Only use the included antenna(s).• If you wall mount your device, make sure that no electrical lines, gas or waterpipes will be damaged.9

Navigation menu