ZyXEL Communications WAP5605 5-GHz Wireless N Media Streaming Box User Manual V 2 Part 2

ZyXEL Communications Corporation 5-GHz Wireless N Media Streaming Box V 2 Part 2

Contents

User manual V.2 (Part 2)

WAP5605 User’s Guide 113APPENDIX APop-up Windows, JavaScripts and JavaPermissionsIn order to use the web configurator you need to allow:• Web browser pop-up windows from your device.• JavaScripts (enabled by default).• Java permissions (enabled by default).Note: The screens used below belong to Internet Explorer version 6, 7 and 8. Screens for other Internet Explorer versions may vary.Internet Explorer Pop-up BlockersYou may have to disable pop-up blocking to log into your device. Either disable pop-up blocking (enabled by default in Windows XP SP (Service Pack) 2) or allow pop-up blocking and create an exception for your device’s IP address.Disable Pop-up Blockers1In Internet Explorer, select Tools, Pop-up Blocker and then select Turn Off Pop-up Blocker. Figure 68 Pop-up BlockerYou can also check if pop-up blocking is disabled in the Pop-up Blocker section in the Privacy tab. 1In Internet Explorer, select Tools, Internet Options, Privacy.
Appendix A Pop-up Windows, JavaScripts and Java PermissionsWAP5605 User’s Guide1142Clear the Block pop-ups check box in the Pop-up Blocker section of the screen. This disables any web pop-up blockers you may have enabled. Figure 69 Internet Options: Privacy3Click Apply to save this setting.Enable Pop-up Blockers with ExceptionsAlternatively, if you only want to allow pop-up windows from your device, see the following steps.1In Internet Explorer, select Tools, Internet Options and then the Privacy tab.
Appendix A Pop-up Windows, JavaScripts and Java PermissionsWAP5605 User’s Guide 1152Select Settings…to open the Pop-up Blocker Settings screen.Figure 70 Internet Options: Privacy3Type the IP address of your device (the web page that you do not want to have blocked) with the prefix “http://”. For example, http://192.168.167.1.
Appendix A Pop-up Windows, JavaScripts and Java PermissionsWAP5605 User’s Guide1164Click Add to move the IP address to the list of Allowed sites.Figure 71 Pop-up Blocker Settings5Click Close to return to the Privacy screen. 6Click Apply to save this setting. JavaScriptsIf pages of the web configurator do not display properly in Internet Explorer, check that JavaScripts are allowed.
Appendix A Pop-up Windows, JavaScripts and Java PermissionsWAP5605 User’s Guide 1171In Internet Explorer, click Tools, Internet Options and then the Security tab. Figure 72 Internet Options: Security 2Click the Custom Level... button. 3Scroll down to Scripting. 4Under Active scripting make sure that Enable is selected (the default).5Under Scripting of Java applets make sure that Enable is selected (the default).
Appendix A Pop-up Windows, JavaScripts and Java PermissionsWAP5605 User’s Guide1186Click OK to close the window.Figure 73 Security Settings - Java ScriptingJava Permissions1From Internet Explorer, click Tools, Internet Options and then the Security tab. 2Click the Custom Level... button. 3Scroll down to Microsoft VM. 4Under Java permissions make sure that a safety level is selected.
Appendix A Pop-up Windows, JavaScripts and Java PermissionsWAP5605 User’s Guide 1195Click OK to close the window.Figure 74 Security Settings - Java JAVA (Sun)1From Internet Explorer, click Tools, Internet Options and then the Advanced tab. 2Make sure that Use Java 2 for <applet> under Java (Sun) is selected.
Appendix A Pop-up Windows, JavaScripts and Java PermissionsWAP5605 User’s Guide1203Click OK to close the window.Figure 75 Java (Sun)Mozilla FirefoxMozilla Firefox 2.0 screens are used here. Screens for other versions may vary slightly. The steps below apply to Mozilla Firefox 3.0 as well.You can enable Java, Javascripts and pop-ups in one screen. Click Tools, then click Options in the screen that appears.Figure 76 Mozilla Firefox: TOOLS > Options
Appendix A Pop-up Windows, JavaScripts and Java PermissionsWAP5605 User’s Guide 121Click Content to show the screen below. Select the check boxes as shown in the following screen.Figure 77 Mozilla Firefox Content SecurityOperaOpera 10 screens are used here. Screens for other versions may vary slightly.
Appendix A Pop-up Windows, JavaScripts and Java PermissionsWAP5605 User’s Guide122Allowing Pop-UpsFrom Opera, click Tools, then Preferences. In the General tab, go to Choose how you prefer to handle pop-ups and select Open all pop-ups.Figure 78 Opera: Allowing Pop-UpsEnabling JavaFrom Opera, click Tools, then Preferences. In the Advanced tab, select Content from the left-side menu. Select the check boxes as shown in the following screen.Figure 79 Opera: Enabling Java
Appendix A Pop-up Windows, JavaScripts and Java PermissionsWAP5605 User’s Guide 123To customize JavaScript behavior in the Opera browser, click JavaScript Options. Figure 80 Opera: JavaScript OptionsSelect the items you want Opera’s JavaScript to apply.
Appendix A Pop-up Windows, JavaScripts and Java PermissionsWAP5605 User’s Guide124
WAP5605 User’s Guide 125APPENDIX BIP Addresses and SubnettingThis appendix introduces IP addresses and subnet masks. IP addresses identify individual devices on a network. Every networking device (including computers, servers, routers, printers, etc.) needs an IP address to communicate across the network. These networking devices are also known as hosts.Subnet masks determine the maximum number of possible hosts on a network. You can also use subnet masks to divide one network into multiple sub-networks.Introduction to IP AddressesOne part of the IP address is the network number, and the other part is the host ID. In the same way that houses on a street share a common street name, the hosts on a network share a common network number. Similarly, as each house has its own house number, each host on the network has its own unique identifying number - the host ID. Routers use the network number to send packets to the correct network, while the host ID determines to which host on the network the packets are delivered.StructureAn IP address is made up of four parts, written in dotted decimal notation (for example, 192.168.1.1). Each of these four parts is known as an octet. An octet is an eight-digit binary number (for example 11000000, which is 192 in decimal notation). Therefore, each octet has a possible range of 00000000 to 11111111 in binary, or 0 to 255 in decimal.
Appendix B IP Addresses and SubnettingWAP5605 User’s Guide126The following figure shows an example IP address in which the first three octets (192.168.1) are the network number, and the fourth octet (16) is the host ID.Figure 81 Network Number and Host IDHow much of the IP address is the network number and how much is the host ID varies according to the subnet mask. Subnet MasksA subnet mask is used to determine which bits are part of the network number, and which bits are part of the host ID (using a logical AND operation). The term “subnet” is short for “sub-network”.A subnet mask has 32 bits. If a bit in the subnet mask is a “1” then the corresponding bit in the IP address is part of the network number. If a bit in the subnet mask is “0” then the corresponding bit in the IP address is part of the host ID. The following example shows a subnet mask identifying the network number (in bold text) and host ID of an IP address (192.168.1.2 in decimal).By convention, subnet masks always consist of a continuous sequence of ones beginning from the leftmost bit of the mask, followed by a continuous sequence of zeros, for a total number of 32 bits.Subnet masks can be referred to by the size of the network number part (the bits with a “1” value). For example, an “8-bit mask” means that the first 8 bits of the mask are ones and the remaining 24 bits are zeroes.Table 46 IP Address Network Number and Host ID Example1ST OCTET:(192)2ND OCTET:(168)3RD OCTET:(1)4TH OCTET(2)IP Address (Binary) 11000000 10101000 00000001 00000010Subnet Mask (Binary) 11111111 11111111 11111111 00000000Network Number 11000000 10101000 00000001Host ID 00000010
Appendix B IP Addresses and SubnettingWAP5605 User’s Guide 127Subnet masks are expressed in dotted decimal notation just like IP addresses. The following examples show the binary and decimal notation for 8-bit, 16-bit, 24-bit and 29-bit subnet masks. Network SizeThe size of the network number determines the maximum number of possible hosts you can have on your network. The larger the number of network number bits, the smaller the number of remaining host ID bits. An IP address with host IDs of all zeros is the IP address of the network (192.168.1.0 with a 24-bit subnet mask, for example). An IP address with host IDs of all ones is the broadcast address for that network (192.168.1.255 with a 24-bit subnet mask, for example).As these two IP addresses cannot be used for individual hosts, calculate the maximum number of possible hosts in a network as follows:NotationSince the mask is always a continuous number of ones beginning from the left, followed by a continuous number of zeros for the remainder of the 32 bit mask, you can simply specify the number of ones instead of writing the value of each octet. This is usually specified by writing a “/” followed by the number of bits in the mask after the address. For example, 192.1.1.0 /25 is equivalent to saying 192.1.1.0 with subnet mask 255.255.255.128. The following table shows some possible subnet masks using both notations. Table 47 Subnet MasksBINARYDECIMAL1ST OCTET 2ND OCTET 3RD OCTET 4TH OCTET8-bit mask 11111111 00000000 00000000 00000000 255.0.0.016-bit mask 11111111 11111111 00000000 00000000 255.255.0.024-bit mask 11111111 11111111 11111111 00000000 255.255.255.029-bit mask 11111111 11111111 11111111 11111000 255.255.255.248Table 48 Maximum Host NumbersSUBNET MASK HOST ID SIZE MAXIMUM NUMBER OF HOSTS8 bits 255.0.0.0 24 bits 224 – 2 1677721416 bits 255.255.0.0 16 bits 216 – 2 6553424 bits 255.255.255.0 8 bits 28 – 2 25429 bits 255.255.255.248 3 bits 23 – 2 6Table 49 Alternative Subnet Mask NotationSUBNET MASK ALTERNATIVE NOTATION LAST OCTET (BINARY) LAST OCTET (DECIMAL)255.255.255.0 /24 0000 0000 0255.255.255.128 /25 1000 0000 128255.255.255.192 /26 1100 0000 192
Appendix B IP Addresses and SubnettingWAP5605 User’s Guide128SubnettingYou can use subnetting to divide one network into multiple sub-networks. In the following example a network administrator creates two sub-networks to isolate a group of servers from the rest of the company network for security reasons.In this example, the company network address is 192.168.1.0. The first three octets of the address (192.168.1) are the network number, and the remaining octet is the host ID, allowing a maximum of 28 – 2 or 254 possible hosts.The following figure shows the company network before subnetting. Figure 82 Subnetting Example: Before SubnettingYou can “borrow” one of the host ID bits to divide the network 192.168.1.0 into two separate sub-networks. The subnet mask is now 25 bits (255.255.255.128 or /25).The “borrowed” host ID bit can have a value of either 0 or 1, allowing two subnets; 192.168.1.0 /25 and 192.168.1.128 /25. 255.255.255.224 /27 1110 0000 224255.255.255.240 /28 1111 0000 240255.255.255.248 /29 1111 1000 248255.255.255.252 /30 1111 1100 252Table 49 Alternative Subnet Mask Notation (continued)SUBNET MASK ALTERNATIVE NOTATION LAST OCTET (BINARY) LAST OCTET (DECIMAL)
Appendix B IP Addresses and SubnettingWAP5605 User’s Guide 129The following figure shows the company network after subnetting. There are now two sub-networks, A and B. Figure 83 Subnetting Example: After SubnettingIn a 25-bit subnet the host ID has 7 bits, so each sub-network has a maximum of 27 – 2 or 126 possible hosts (a host ID of all zeroes is the subnet’s address itself, all ones is the subnet’s broadcast address).192.168.1.0 with mask 255.255.255.128 is subnet A itself, and 192.168.1.127 with mask 255.255.255.128 is its broadcast address. Therefore, the lowest IP address that can be assigned to an actual host for subnet A is 192.168.1.1 and the highest is 192.168.1.126. Similarly, the host ID range for subnet B is 192.168.1.129 to 192.168.1.254.Example: Four Subnets The previous example illustrated using a 25-bit subnet mask to divide a 24-bit address into two subnets. Similarly, to divide a 24-bit address into four subnets, you need to “borrow” two host ID bits to give four possible combinations (00, 01, 10 and 11). The subnet mask is 26 bits (11111111.11111111.11111111.11000000) or 255.255.255.192. Each subnet contains 6 host ID bits, giving 26 - 2 or 62 hosts for each subnet (a host ID of all zeroes is the subnet itself, all ones is the subnet’s broadcast address). Table 50 Subnet 1IP/SUBNET MASK NETWORK NUMBER LAST OCTET BIT VALUEIP Address (Decimal) 192.168.1. 0IP Address (Binary) 11000000.10101000.00000001. 00000000Subnet Mask (Binary) 11111111.11111111.11111111. 11000000
Appendix B IP Addresses and SubnettingWAP5605 User’s Guide130Example: Eight SubnetsSimilarly, use a 27-bit mask to create eight subnets (000, 001, 010, 011, 100, 101, 110 and 111). Subnet Address: 192.168.1.0Lowest Host ID: 192.168.1.1Broadcast Address: 192.168.1.63Highest Host ID: 192.168.1.62Table 51 Subnet 2IP/SUBNET MASK NETWORK NUMBER LAST OCTET BIT VALUEIP Address 192.168.1. 64IP Address (Binary) 11000000.10101000.00000001. 01000000Subnet Mask (Binary) 11111111.11111111.11111111. 11000000Subnet Address: 192.168.1.64Lowest Host ID: 192.168.1.65Broadcast Address: 192.168.1.127Highest Host ID: 192.168.1.126Table 52 Subnet 3IP/SUBNET MASK NETWORK NUMBER LAST OCTET BIT VALUEIP Address 192.168.1. 128IP Address (Binary) 11000000.10101000.00000001. 10000000Subnet Mask (Binary) 11111111.11111111.11111111. 11000000Subnet Address: 192.168.1.128Lowest Host ID: 192.168.1.129Broadcast Address: 192.168.1.191Highest Host ID: 192.168.1.190Table 53 Subnet 4IP/SUBNET MASK NETWORK NUMBER LAST OCTET BIT VALUEIP Address 192.168.1. 192IP Address (Binary) 11000000.10101000.00000001. 11000000Subnet Mask (Binary) 11111111.11111111.11111111. 11000000Subnet Address: 192.168.1.192Lowest Host ID: 192.168.1.193Broadcast Address: 192.168.1.255Highest Host ID: 192.168.1.254Table 50 Subnet 1 (continued)IP/SUBNET MASK NETWORK NUMBER LAST OCTET BIT VALUE
Appendix B IP Addresses and SubnettingWAP5605 User’s Guide 131The following table shows IP address last octet values for each subnet.Subnet PlanningThe following table is a summary for subnet planning on a network with a 24-bit network number.The following table is a summary for subnet planning on a network with a 16-bit network number. Table 54 Eight SubnetsSUBNET SUBNET ADDRESS FIRST ADDRESS LAST ADDRESS BROADCAST ADDRESS1 0 1 30 31232 33 62 63364 65 94 95496 97 126 1275128 129 158 1596160 161 190 1917192 193 222 2238224 225 254 255Table 55 24-bit Network Number Subnet PlanningNO. “BORROWED” HOST BITS SUBNET MASK NO. SUBNETS NO. HOSTS PER SUBNET1255.255.255.128 (/25) 21262255.255.255.192 (/26) 4623255.255.255.224 (/27) 8304255.255.255.240 (/28) 16 145255.255.255.248 (/29) 32 66255.255.255.252 (/30) 64 27255.255.255.254 (/31) 128 1Table 56 16-bit Network Number Subnet PlanningNO. “BORROWED” HOST BITS SUBNET MASK NO. SUBNETS NO. HOSTS PER SUBNET1255.255.128.0 (/17) 2327662255.255.192.0 (/18) 4163823255.255.224.0 (/19) 881904255.255.240.0 (/20) 16 40945255.255.248.0 (/21) 32 20466255.255.252.0 (/22) 64 10227255.255.254.0 (/23) 128 5108255.255.255.0 (/24) 256 2549255.255.255.128 (/25) 512 12610 255.255.255.192 (/26) 1024 6211 255.255.255.224 (/27) 2048 3012 255.255.255.240 (/28) 4096 14
Appendix B IP Addresses and SubnettingWAP5605 User’s Guide132Configuring IP AddressesWhere you obtain your network number depends on your particular situation. If the ISP or your network administrator assigns you a block of registered IP addresses, follow their instructions in selecting the IP addresses and the subnet mask.If the ISP did not explicitly give you an IP network number, then most likely you have a single user account and the ISP will assign you a dynamic IP address when the connection is established. If this is the case, it is recommended that you select a network number from 192.168.0.0 to 192.168.255.0. The Internet Assigned Number Authority (IANA) reserved this block of addresses specifically for private use; please do not use any other number unless you are told otherwise. You must also enable Network Address Translation (NAT) on the WAP5605. Once you have decided on the network number, pick an IP address for your WAP5605 that is easy to remember (for instance, 192.168.1.1) but make sure that no other device on your network is using that IP address.The subnet mask specifies the network number portion of an IP address. Your WAP5605 will compute the subnet mask automatically based on the IP address that you entered. You don't need to change the subnet mask computed by the WAP5605 unless you are instructed to do otherwise.Private IP AddressesEvery machine on the Internet must have a unique address. If your networks are isolated from the Internet (running only between two branch offices, for example) you can assign any IP addresses to the hosts without problems. However, the Internet Assigned Numbers Authority (IANA) has reserved the following three blocks of IP addresses specifically for private networks:• 10.0.0.0 — 10.255.255.255• 172.16.0.0 — 172.31.255.255• 192.168.0.0 — 192.168.255.255You can obtain your IP address from the IANA, from an ISP, or it can be assigned from a private network. If you belong to a small organization and your Internet access is through an ISP, the ISP can provide you with the Internet addresses for your local networks. On the other hand, if you are part of a much larger organization, you should consult your network administrator for the appropriate IP addresses.Regardless of your particular situation, do not create an arbitrary IP address; always follow the guidelines above. For more information on address assignment, please refer to RFC 1597, Address Allocation for Private Internets and RFC 1466, Guidelines for Management of IP Address Space.13 255.255.255.248 (/29) 8192 614 255.255.255.252 (/30) 16384 215 255.255.255.254 (/31) 32768 1Table 56 16-bit Network Number Subnet Planning (continued)NO. “BORROWED” HOST BITS SUBNET MASK NO. SUBNETS NO. HOSTS PER SUBNET
Appendix B IP Addresses and SubnettingWAP5605 User’s Guide 133IP Address ConflictsEach device on a network must have a unique IP address. Devices with duplicate IP addresses on the same network will not be able to access the Internet or other resources. The devices may also be unreachable through the network. Conflicting Computer IP Addresses ExampleMore than one device can not use the same IP address. In the following example computer A has a static (or fixed) IP address that is the same as the IP address that a DHCP server assigns to computer B which is a DHCP client. Neither can access the Internet. This problem can be solved by assigning a different static IP address to computer A or setting computer A to obtain an IP address automatically. Figure 84 Conflicting Computer IP Addresses ExampleConflicting Router IP Addresses ExampleSince a router connects different networks, it must have interfaces using different network numbers. For example, if a router is set between a LAN and the Internet (WAN), the router’s LAN and WAN addresses must be on different subnets. In the following example, the LAN and WAN are on the same subnet. The LAN computers cannot access the Internet because the router cannot route between networks.Figure 85 Conflicting Router IP Addresses Example
Appendix B IP Addresses and SubnettingWAP5605 User’s Guide134Conflicting Computer and Router IP Addresses ExampleMore than one device can not use the same IP address. In the following example, the computer and the router’s LAN port both use 192.168.1.1 as the IP address. The computer cannot access the Internet. This problem can be solved by assigning a different IP address to the computer or the router’s LAN port. Figure 86 Conflicting Computer and Router IP Addresses Example
WAP5605 User’s Guide 135APPENDIX CSetting Up Your Computer’s IP AddressNote: Your specific WAP5605 may not support all of the operating systems described in this appendix. See the product specifications for more information about which operating systems are supported.This appendix shows you how to configure the IP settings on your computer in order for it to be able to communicate with the other devices on your network. Windows Vista/XP/2000, Mac OS 9/OS X, and all versions of UNIX/LINUX include the software components you need to use TCP/IP on your computer. If you manually assign IP information instead of using a dynamic IP, make sure that your network’s computers have IP addresses that place them in the same subnet.In this appendix, you can set up an IP address for:•Windows XP/NT/2000 on page 135•Windows Vista on page 139•Windows 7 on page 143•Mac OS X: 10.3 and 10.4 on page 147•Mac OS X: 10.5 and 10.6 on page 150•Linux: Ubuntu 8 (GNOME) on page 153•Linux: openSUSE 10.3 (KDE) on page 157Windows XP/NT/2000The following example uses the default Windows XP display theme but can also apply to Windows 2000 and Windows NT.
Appendix C Setting Up Your Computer’s IP AddressWAP5605 User’s Guide1361Click Start > Control Panel.2In the Control Panel, click the Network Connections icon.3Right-click Local Area Connection and then select Properties.
Appendix C Setting Up Your Computer’s IP AddressWAP5605 User’s Guide 1374On the General tab, select Internet Protocol (TCP/IP) and then click Properties.
Appendix C Setting Up Your Computer’s IP AddressWAP5605 User’s Guide1385The Internet Protocol TCP/IP Properties window opens.6Select Obtain an IP address automatically if your network administrator or ISP assigns your IP address dynamically.Select Use the following IP Address and fill in the IP address, Subnet mask, and Default gateway fields if you have a static IP address that was assigned to you by your network administrator or ISP. You may also have to enter a Preferred DNS server and an Alternate DNS server, if that information was provided.7Click OK to close the Internet Protocol (TCP/IP) Properties window.8Click OK to close the Local Area Connection Properties window.Verifying Settings1Click Start > All Programs > Accessories > Command Prompt.2In the Command Prompt window, type "ipconfig" and then press [ENTER]. You can also go to Start > Control Panel > Network Connections, right-click a network connection, click Status and then click the Support tab to view your IP address and connection information.
Appendix C Setting Up Your Computer’s IP AddressWAP5605 User’s Guide 139Windows VistaThis section shows screens from Windows Vista Professional.1Click Start > Control Panel.2In the Control Panel, click the Network and Internet icon.3Click the Network and Sharing Center icon.
Appendix C Setting Up Your Computer’s IP AddressWAP5605 User’s Guide1404Click Manage network connections.5Right-click Local Area Connection and then select Properties.Note: During this procedure, click Continue whenever Windows displays a screen saying that it needs your permission to continue.
Appendix C Setting Up Your Computer’s IP AddressWAP5605 User’s Guide 1416Select Internet Protocol Version 4 (TCP/IPv4) and then select Properties.
Appendix C Setting Up Your Computer’s IP AddressWAP5605 User’s Guide1427The Internet Protocol Version 4 (TCP/IPv4) Properties window opens.8Select Obtain an IP address automatically if your network administrator or ISP assigns your IP address dynamically.Select Use the following IP Address and fill in the IP address, Subnet mask, and Default gateway fields if you have a static IP address that was assigned to you by your network administrator or ISP. You may also have to enter a Preferred DNS server and an Alternate DNS server, if that information was provided.Click Advanced.9Click OK to close the Internet Protocol (TCP/IP) Properties window.10 Click OK to close the Local Area Connection Properties window.Verifying Settings1Click Start > All Programs > Accessories > Command Prompt.2In the Command Prompt window, type "ipconfig" and then press [ENTER]. You can also go to Start > Control Panel > Network Connections, right-click a network connection, click Status and then click the Support tab to view your IP address and connection information.
Appendix C Setting Up Your Computer’s IP AddressWAP5605 User’s Guide 143Windows 7This section shows screens from Windows 7 Enterprise.1Click Start > Control Panel.2In the Control Panel, click View network status and tasks under the Network and Internet category.3Click Change adapter settings.
Appendix C Setting Up Your Computer’s IP AddressWAP5605 User’s Guide1444Double click Local Area Connection and then select Properties.Note: During this procedure, click Continue whenever Windows displays a screen saying that it needs your permission to continue.
Appendix C Setting Up Your Computer’s IP AddressWAP5605 User’s Guide 1455Select Internet Protocol Version 4 (TCP/IPv4) and then select Properties.
Appendix C Setting Up Your Computer’s IP AddressWAP5605 User’s Guide1466The Internet Protocol Version 4 (TCP/IPv4) Properties window opens.7Select Obtain an IP address automatically if your network administrator or ISP assigns your IP address dynamically.Select Use the following IP Address and fill in the IP address, Subnet mask, and Default gateway fields if you have a static IP address that was assigned to you by your network administrator or ISP. You may also have to enter a Preferred DNS server and an Alternate DNS server, if that information was provided. Click Advanced if you want to configure advanced settings for IP, DNS and WINS. 8Click OK to close the Internet Protocol (TCP/IP) Properties window.9Click OK to close the Local Area Connection Properties window.Verifying Settings1Click Start > All Programs > Accessories > Command Prompt.2In the Command Prompt window, type "ipconfig" and then press [ENTER].
Appendix C Setting Up Your Computer’s IP AddressWAP5605 User’s Guide 1473The IP settings are displayed as follows.Mac OS X: 10.3 and 10.4The screens in this section are from Mac OS X 10.4 but can also apply to 10.3.1Click Apple > System Preferences.
Appendix C Setting Up Your Computer’s IP AddressWAP5605 User’s Guide1482In the System Preferences window, click the Network icon.3When the Network preferences pane opens, select Built-in Ethernet from the network connection type list, and then click Configure.
Appendix C Setting Up Your Computer’s IP AddressWAP5605 User’s Guide 1494For dynamically assigned settings, select Using DHCP from the Configure IPv4 list in the TCP/IP tab.5For statically assigned settings, do the following:•From the Configure IPv4 list, select Manually.•In the IP Address field, type your IP address.•In the Subnet Mask field, type your subnet mask.•In the Router field, type the IP address of your device.6Click Apply Now and close the window.
Appendix C Setting Up Your Computer’s IP AddressWAP5605 User’s Guide150Verifying SettingsCheck your TCP/IP properties by clicking Applications > Utilities > Network Utilities, and then selecting the appropriate Network Interface from the Info tab.Figure 87 Mac OS X 10.4: Network UtilityMac OS X: 10.5 and 10.6The screens in this section are from Mac OS X 10.5 but can also apply to 10.6.1Click Apple > System Preferences.
Appendix C Setting Up Your Computer’s IP AddressWAP5605 User’s Guide 1512In System Preferences, click the Network icon.3When the Network preferences pane opens, select Ethernet from the list of available connection types.4From the Configure list, select Using DHCP for dynamically assigned settings.5For statically assigned settings, do the following:
Appendix C Setting Up Your Computer’s IP AddressWAP5605 User’s Guide152•From the Configure list, select Manually.•In the IP Address field, enter your IP address.•In the Subnet Mask field, enter your subnet mask.•In the Router field, enter the IP address of your WAP5605.6Click Apply and close the window.
Appendix C Setting Up Your Computer’s IP AddressWAP5605 User’s Guide 153Verifying SettingsCheck your TCP/IP properties by clicking Applications > Utilities > Network Utilities, and then selecting the appropriate Network interface from the Info tab.Figure 88 Mac OS X 10.5: Network UtilityLinux: Ubuntu 8 (GNOME)This section shows you how to configure your computer’s TCP/IP settings in the GNU Object Model Environment (GNOME) using the Ubuntu 8 Linux distribution. The procedure, screens and file locations may vary depending on your specific distribution, release version, and individual configuration. The following screens use the default Ubuntu 8 installation.Note: Make sure you are logged in as the root administrator. Follow the steps below to configure your computer IP address in GNOME: 1Click System > Administration > Network.
Appendix C Setting Up Your Computer’s IP AddressWAP5605 User’s Guide1542When the Network Settings window opens, click Unlock to open the Authenticate window. (By default, the Unlock button is greyed out until clicked.) You cannot make changes to your configuration unless you first enter your admin password.3In the Authenticate window, enter your admin account name and password then click the Authenticate button.
Appendix C Setting Up Your Computer’s IP AddressWAP5605 User’s Guide 1554In the Network Settings window, select the connection that you want to configure, then click Properties.5The Properties dialog box opens.•In the Configuration list, select Automatic Configuration (DHCP) if you have a dynamic IP address.•In the Configuration list, select Static IP address if you have a static IP address. Fill in the IP address, Subnet mask, and Gateway address fields. 6Click OK to save the changes and close the Properties dialog box and return to the Network Settings screen.
Appendix C Setting Up Your Computer’s IP AddressWAP5605 User’s Guide1567If you know your DNS server IP address(es), click the DNS tab in the Network Settings window and then enter the DNS server information in the fields provided. 8Click the Close button to apply the changes.
Appendix C Setting Up Your Computer’s IP AddressWAP5605 User’s Guide 157Verifying SettingsCheck your TCP/IP properties by clicking System > Administration > Network Tools, and then selecting the appropriate Network device from the Devices tab. The Interface Statistics column shows data if your connection is working properly.Figure 89 Ubuntu 8: Network ToolsLinux: openSUSE 10.3 (KDE)This section shows you how to configure your computer’s TCP/IP settings in the K Desktop Environment (KDE) using the openSUSE 10.3 Linux distribution. The procedure, screens and file locations may vary depending on your specific distribution, release version, and individual configuration. The following screens use the default openSUSE 10.3 installation.Note: Make sure you are logged in as the root administrator. Follow the steps below to configure your computer IP address in the KDE:
Appendix C Setting Up Your Computer’s IP AddressWAP5605 User’s Guide1581Click K Menu > Computer > Administrator Settings (YaST).2When the Run as Root - KDE su dialog opens, enter the admin password and click OK.
Appendix C Setting Up Your Computer’s IP AddressWAP5605 User’s Guide 1593When the YaST Control Center window opens, select Network Devices and then click the Network Card icon.4When the Network Settings window opens, click the Overview tab, select the appropriate connection Name from the list, and then click the Configure button.
Appendix C Setting Up Your Computer’s IP AddressWAP5605 User’s Guide1605When the Network Card Setup window opens, click the Address tabFigure 90 openSUSE 10.3: Network Card Setup6Select Dynamic Address (DHCP) if you have a dynamic IP address.Select Statically assigned IP Address if you have a static IP address. Fill in the IP address, Subnet mask, and Hostname fields.7Click Next to save the changes and close the Network Card Setup window.
Appendix C Setting Up Your Computer’s IP AddressWAP5605 User’s Guide 1618If you know your DNS server IP address(es), click the Hostname/DNS tab in Network Settings and then enter the DNS server information in the fields provided.9Click Finish to save your settings and close the window.Verifying SettingsClick the KNetwork Manager icon on the Task bar to check your TCP/IP properties. From the Options sub-menu, select Show Connection Information.Figure 91 openSUSE 10.3: KNetwork Manager
Appendix C Setting Up Your Computer’s IP AddressWAP5605 User’s Guide162When the Connection Status - KNetwork Manager window opens, click the Statistics tab to see if your connection is working properly.Figure 92 openSUSE: Connection Status - KNetwork Manager
WAP5605 User’s Guide 163APPENDIX DWireless LANsWireless LAN TopologiesThis section discusses ad-hoc and infrastructure wireless LAN topologies.Ad-hoc Wireless LAN ConfigurationThe simplest WLAN configuration is an independent (Ad-hoc) WLAN that connects a set of computers with wireless adapters (A, B, C). Any time two or more wireless adapters are within range of each other, they can set up an independent network, which is commonly referred to as an ad-hoc network or Independent Basic Service Set (IBSS). The following diagram shows an example of notebook computers using wireless adapters to form an ad-hoc wireless LAN. Figure 93 Peer-to-Peer Communication in an Ad-hoc NetworkBSSA Basic Service Set (BSS) exists when all communications between wireless clients or between a wireless client and a wired network client go through one access point (AP). Intra-BSS traffic is traffic between wireless clients in the BSS. When Intra-BSS is enabled, wireless client A and B can access the wired network and communicate with each other. When Intra-BSS is
Appendix D Wireless LANsWAP5605 User’s Guide164disabled, wireless client A and B can still access the wired network but cannot communicate with each other.Figure 94 Basic Service SetESSAn Extended Service Set (ESS) consists of a series of overlapping BSSs, each containing an access point, with each access point connected together by a wired network. This wired connection between APs is called a Distribution System (DS).This type of wireless LAN topology is called an Infrastructure WLAN. The Access Points not only provide communication with the wired network but also mediate wireless network traffic in the immediate neighborhood.
Appendix D Wireless LANsWAP5605 User’s Guide 165An ESSID (ESS IDentification) uniquely identifies each ESS. All access points and their associated wireless clients within the same ESS must have the same ESSID in order to communicate.Figure 95 Infrastructure WLANChannelA channel is the radio frequency(ies) used by wireless devices to transmit and receive data. Channels available depend on your geographical area. You may have a choice of channels (for your region) so you should use a channel different from an adjacent AP (access point) to reduce interference. Interference occurs when radio signals from different access points overlap causing interference and degrading performance.Adjacent channels partially overlap however. To avoid interference due to overlap, your AP should be on a channel at least five channels away from a channel that an adjacent AP is using. For example, if your region has 11 channels and an adjacent AP is using channel 1, then you need to select a channel between 6 or 11.RTS/CTSA hidden node occurs when two stations are within range of the same access point, but are not within range of each other. The following figure illustrates a hidden node. Both stations (STA) are within range of the access point (AP) or wireless gateway, but out-of-range of each other, so they
Appendix D Wireless LANsWAP5605 User’s Guide166cannot "hear" each other, that is they do not know if the channel is currently being used. Therefore, they are considered hidden from each other. Figure 96 RTS/CTSWhen station A sends data to the AP, it might not know that the station B is already using the channel. If these two stations send data at the same time, collisions may occur when both sets of data arrive at the AP at the same time, resulting in a loss of messages for both stations.RTS/CTS is designed to prevent collisions due to hidden nodes. An RTS/CTS defines the biggest size data frame you can send before an RTS (Request To Send)/CTS (Clear to Send) handshake is invoked.When a data frame exceeds the RTS/CTS value you set (between 0 to 2432 bytes), the station that wants to transmit this frame must first send an RTS (Request To Send) message to the AP for permission to send it. The AP then responds with a CTS (Clear to Send) message to all other stations within its range to notify them to defer their transmission. It also reserves and confirms with the requesting station the time frame for the requested transmission.Stations can send frames smaller than the specified RTS/CTS directly to the AP without the RTS (Request To Send)/CTS (Clear to Send) handshake. You should only configure RTS/CTS if the possibility of hidden nodes exists on your network and the "cost" of resending large frames is more than the extra network overhead involved in the RTS (Request To Send)/CTS (Clear to Send) handshake. If the RTS/CTS value is greater than the Fragmentation Threshold value (see next), then the RTS (Request To Send)/CTS (Clear to Send) handshake will never occur as data frames will be fragmented before they reach RTS/CTS size. Note: Enabling the RTS Threshold causes redundant network overhead that could negatively affect the throughput performance instead of providing a remedy.Fragmentation ThresholdA Fragmentation Threshold is the maximum data fragment size (between 256 and 2432 bytes) that can be sent in the wireless network before the AP will fragment the packet into smaller data frames.A large Fragmentation Threshold is recommended for networks not prone to interference while you should set a smaller threshold for busy networks or networks that are prone to interference.
Appendix D Wireless LANsWAP5605 User’s Guide 167If the Fragmentation Threshold value is smaller than the RTS/CTS value (see previously) you set then the RTS (Request To Send)/CTS (Clear to Send) handshake will never occur as data frames will be fragmented before they reach RTS/CTS size.Preamble TypePreamble is used to signal that data is coming to the receiver. Short and long refer to the length of the synchronization field in a packet.Short preamble increases performance as less time sending preamble means more time for sending data. All IEEE 802.11 compliant wireless adapters support long preamble, but not all support short preamble. Use long preamble if you are unsure what preamble mode other wireless devices on the network support, and to provide more reliable communications in busy wireless networks. Use short preamble if you are sure all wireless devices on the network support it, and to provide more efficient communications.Use the dynamic setting to automatically use short preamble when all wireless devices on the network support it, otherwise the WAP5605 uses long preamble.Note: The wireless devices MUST use the same preamble mode in order to communicate.IEEE 802.11g Wireless LANIEEE 802.11g is fully compatible with the IEEE 802.11b standard. This means an IEEE 802.11b adapter can interface directly with an IEEE 802.11g access point (and vice versa) at 11 Mbps or lower depending on range. IEEE 802.11g has several intermediate rate steps between the maximum and minimum data rates. The IEEE 802.11g data rate and modulation are as follows:Wireless Security OverviewWireless security is vital to your network to protect wireless communication between wireless clients, access points and the wired network.Wireless security methods available on the WAP5605 are data encryption, wireless client authentication, restricting access by device MAC address and hiding the WAP5605 identity.Table 57 IEEE 802.11gDATA RATE (MBPS) MODULATION1 DBPSK (Differential Binary Phase Shift Keyed)2 DQPSK (Differential Quadrature Phase Shift Keying)5.5 / 11 CCK (Complementary Code Keying) 6/9/12/18/24/36/48/54OFDM (Orthogonal Frequency Division Multiplexing)
Appendix D Wireless LANsWAP5605 User’s Guide168The following figure shows the relative effectiveness of these wireless security methods available on your WAP5605.Note: You must enable the same wireless security settings on the WAP5605 and on all wireless clients that you want to associate with it. IEEE 802.1xIn June 2001, the IEEE 802.1x standard was designed to extend the features of IEEE 802.11 to support extended authentication as well as providing additional accounting and control features. It is supported by Windows XP and a number of network devices. Some advantages of IEEE 802.1x are:• User based identification that allows for roaming.• Support for RADIUS (Remote Authentication Dial In User Service, RFC 2138, 2139) for centralized user profile and accounting management on a network RADIUS server. • Support for EAP (Extensible Authentication Protocol, RFC 2486) that allows additional authentication methods to be deployed with no changes to the access point or the wireless clients. RADIUSRADIUS is based on a client-server model that supports authentication, authorization and accounting. The access point is the client and the server is the RADIUS server. The RADIUS server handles the following tasks:• Authentication Determines the identity of the users.•AuthorizationDetermines the network services available to authenticated users once they are connected to the network.• AccountingKeeps track of the client’s network activity. Table 58 Wireless Security LevelsSECURITY LEVEL SECURITY TYPELeast Secure Most SecureUnique SSID (Default)Unique SSID with Hide SSID EnabledMAC Address FilteringWEP EncryptionIEEE802.1x EAP with RADIUS Server AuthenticationWi-Fi Protected Access (WPA)WPA2
Appendix D Wireless LANsWAP5605 User’s Guide 169RADIUS is a simple package exchange in which your AP acts as a message relay between the wireless client and the network RADIUS server. Types of RADIUS MessagesThe following types of RADIUS messages are exchanged between the access point and the RADIUS server for user authentication:• Access-RequestSent by an access point requesting authentication.• Access-RejectSent by a RADIUS server rejecting access.• Access-AcceptSent by a RADIUS server allowing access. • Access-ChallengeSent by a RADIUS server requesting more information in order to allow access. The access point sends a proper response from the user and then sends another Access-Request message. The following types of RADIUS messages are exchanged between the access point and the RADIUS server for user accounting:• Accounting-RequestSent by the access point requesting accounting.• Accounting-ResponseSent by the RADIUS server to indicate that it has started or stopped accounting. In order to ensure network security, the access point and the RADIUS server use a shared secret key, which is a password, they both know. The key is not sent over the network. In addition to the shared key, password information exchanged is also encrypted to protect the network from unauthorized access. Types of EAP Authentication This section discusses some popular authentication types: EAP-MD5, EAP-TLS, EAP-TTLS, PEAP and LEAP. Your wireless LAN device may not support all authentication types. EAP (Extensible Authentication Protocol) is an authentication protocol that runs on top of the IEEE 802.1x transport mechanism in order to support multiple types of user authentication. By using EAP to interact with an EAP-compatible RADIUS server, an access point helps a wireless station and a RADIUS server perform authentication. The type of authentication you use depends on the RADIUS server and an intermediary AP(s) that supports IEEE 802.1x. .For EAP-TLS authentication type, you must first have a wired connection to the network and obtain the certificate(s) from a certificate authority (CA). A certificate (also called digital IDs) can be used to authenticate users and a CA issues certificates and guarantees the identity of each certificate owner.
Appendix D Wireless LANsWAP5605 User’s Guide170EAP-MD5 (Message-Digest Algorithm 5)MD5 authentication is the simplest one-way authentication method. The authentication server sends a challenge to the wireless client. The wireless client ‘proves’ that it knows the password by encrypting the password with the challenge and sends back the information. Password is not sent in plain text. However, MD5 authentication has some weaknesses. Since the authentication server needs to get the plaintext passwords, the passwords must be stored. Thus someone other than the authentication server may access the password file. In addition, it is possible to impersonate an authentication server as MD5 authentication method does not perform mutual authentication. Finally, MD5 authentication method does not support data encryption with dynamic session key. You must configure WEP encryption keys for data encryption. EAP-TLS (Transport Layer Security)With EAP-TLS, digital certifications are needed by both the server and the wireless clients for mutual authentication. The server presents a certificate to the client. After validating the identity of the server, the client sends a different certificate to the server. The exchange of certificates is done in the open before a secured tunnel is created. This makes user identity vulnerable to passive attacks. A digital certificate is an electronic ID card that authenticates the sender’s identity. However, to implement EAP-TLS, you need a Certificate Authority (CA) to handle certificates, which imposes a management overhead. EAP-TTLS (Tunneled Transport Layer Service) EAP-TTLS is an extension of the EAP-TLS authentication that uses certificates for only the server-side authentications to establish a secure connection. Client authentication is then done by sending username and password through the secure connection, thus client identity is protected. For client authentication, EAP-TTLS supports EAP methods and legacy authentication methods such as PAP, CHAP, MS-CHAP and MS-CHAP v2. PEAP (Protected EAP) Like EAP-TTLS, server-side certificate authentication is used to establish a secure connection, then use simple username and password methods through the secured connection to authenticate the clients, thus hiding client identity. However, PEAP only supports EAP methods, such as EAP-MD5, EAP-MSCHAPv2 and EAP-GTC (EAP-Generic Token Card), for client authentication. EAP-GTC is implemented only by Cisco.LEAPLEAP (Lightweight Extensible Authentication Protocol) is a Cisco implementation of IEEE 802.1x. Dynamic WEP Key ExchangeThe AP maps a unique key that is generated with the RADIUS server. This key expires when the wireless connection times out, disconnects or reauthentication times out. A new WEP key is generated each time reauthentication is performed.
Appendix D Wireless LANsWAP5605 User’s Guide 171If this feature is enabled, it is not necessary to configure a default encryption key in the wireless security configuration screen. You may still configure and store keys, but they will not be used while dynamic WEP is enabled.Note: EAP-MD5 cannot be used with Dynamic WEP Key ExchangeFor added security, certificate-based authentications (EAP-TLS, EAP-TTLS and PEAP) use dynamic keys for data encryption. They are often deployed in corporate environments, but for public deployment, a simple user name and password pair is more practical. The following table is a comparison of the features of authentication types.WPA and WPA2Wi-Fi Protected Access (WPA) is a subset of the IEEE 802.11i standard. WPA2 (IEEE 802.11i) is a wireless security standard that defines stronger encryption, authentication and key management than WPA. Key differences between WPA or WPA2 and WEP are improved data encryption and user authentication.If both an AP and the wireless clients support WPA2 and you have an external RADIUS server, use WPA2 for stronger data encryption. If you don't have an external RADIUS server, you should use WPA2-PSK (WPA2-Pre-Shared Key) that only requires a single (identical) password entered into each access point, wireless gateway and wireless client. As long as the passwords match, a wireless client will be granted access to a WLAN. If the AP or the wireless clients do not support WPA2, just use WPA or WPA-PSK depending on whether you have an external RADIUS server or not.Select WEP only when the AP and/or wireless clients do not support WPA or WPA2. WEP is less secure than WPA or WPA2.Encryption WPA improves data encryption by using Temporal Key Integrity Protocol (TKIP), Message Integrity Check (MIC) and IEEE 802.1x. WPA2 also uses TKIP when required for compatibility reasons, but offers stronger encryption than TKIP with Advanced Encryption Standard (AES) in the Counter mode with Cipher block chaining Message authentication code Protocol (CCMP).TKIP uses 128-bit keys that are dynamically generated and distributed by the authentication server. AES (Advanced Encryption Standard) is a block cipher that uses a 256-bit mathematical algorithm Table 59 Comparison of EAP Authentication TypesEAP-MD5 EAP-TLS EAP-TTLS PEAP LEAPMutual Authentication No Yes Yes Yes YesCertificate – Client No Yes Optional Optional NoCertificate – Server No Yes Yes Yes NoDynamic Key Exchange No Yes Yes Yes YesCredential Integrity None Strong Strong Strong ModerateDeployment Difficulty Easy Hard Moderate Moderate ModerateClient Identity Protection No No Yes Yes No
Appendix D Wireless LANsWAP5605 User’s Guide172called Rijndael. They both include a per-packet key mixing function, a Message Integrity Check (MIC) named Michael, an extended initialization vector (IV) with sequencing rules, and a re-keying mechanism.WPA and WPA2 regularly change and rotate the encryption keys so that the same encryption key is never used twice. The RADIUS server distributes a Pairwise Master Key (PMK) key to the AP that then sets up a key hierarchy and management system, using the PMK to dynamically generate unique data encryption keys to encrypt every data packet that is wirelessly communicated between the AP and the wireless clients. This all happens in the background automatically.The Message Integrity Check (MIC) is designed to prevent an attacker from capturing data packets, altering them and resending them. The MIC provides a strong mathematical function in which the receiver and the transmitter each compute and then compare the MIC. If they do not match, it is assumed that the data has been tampered with and the packet is dropped. By generating unique data encryption keys for every data packet and by creating an integrity checking mechanism (MIC), with TKIP and AES it is more difficult to decrypt data on a Wi-Fi network than WEP and difficult for an intruder to break into the network. The encryption mechanisms used for WPA(2) and WPA(2)-PSK are the same. The only difference between the two is that WPA(2)-PSK uses a simple common password, instead of user-specific credentials. The common-password approach makes WPA(2)-PSK susceptible to brute-force password-guessing attacks but it’s still an improvement over WEP as it employs a consistent, single, alphanumeric password to derive a PMK which is used to generate unique temporal encryption keys. This prevent all wireless devices sharing the same encryption keys. (a weakness of WEP)User Authentication WPA and WPA2 apply IEEE 802.1x and Extensible Authentication Protocol (EAP) to authenticate wireless clients using an external RADIUS database. WPA2 reduces the number of key exchange messages from six to four (CCMP 4-way handshake) and shortens the time required to connect to a network. Other WPA2 authentication features that are different from WPA include key caching and pre-authentication. These two features are optional and may not be supported in all wireless devices.Key caching allows a wireless client to store the PMK it derived through a successful authentication with an AP. The wireless client uses the PMK when it tries to connect to the same AP and does not need to go with the authentication process again.Pre-authentication enables fast roaming by allowing the wireless client (already connecting to an AP) to perform IEEE 802.1x authentication with another AP before connecting to it.Wireless Client WPA SupplicantsA wireless client supplicant is the software that runs on an operating system instructing the wireless client how to use WPA. At the time of writing, the most widely available supplicant is the WPA patch for Windows XP, Funk Software's Odyssey client. The Windows XP patch is a free download that adds WPA capability to Windows XP's built-in "Zero Configuration" wireless client. However, you must run Windows XP to use it.
Appendix D Wireless LANsWAP5605 User’s Guide 173WPA(2) with RADIUS Application ExampleTo set up WPA(2), you need the IP address of the RADIUS server, its port number (default is 1812), and the RADIUS shared secret. A WPA(2) application example with an external RADIUS server looks as follows. "A" is the RADIUS server. "DS" is the distribution system.1The AP passes the wireless client's authentication request to the RADIUS server.2The RADIUS server then checks the user's identification against its database and grants or denies network access accordingly.3A 256-bit Pairwise Master Key (PMK) is derived from the authentication process by the RADIUS server and the client.4The RADIUS server distributes the PMK to the AP. The AP then sets up a key hierarchy and management system, using the PMK to dynamically generate unique data encryption keys. The keys are used to encrypt every data packet that is wirelessly communicated between the AP and the wireless clients.Figure 97 WPA(2) with RADIUS Application ExampleWPA(2)-PSK Application ExampleA WPA(2)-PSK application looks as follows.1First enter identical passwords into the AP and all wireless clients. The Pre-Shared Key (PSK) must consist of between 8 and 63 ASCII characters or 64 hexadecimal characters (including spaces and symbols).2The AP checks each wireless client's password and allows it to join the network only if the password matches.3The AP and wireless clients generate a common PMK (Pairwise Master Key). The key itself is not sent over the network, but is derived from the PSK and the SSID.
Appendix D Wireless LANsWAP5605 User’s Guide1744The AP and wireless clients use the TKIP or AES encryption process, the PMK and information exchanged in a handshake to create temporal encryption keys. They use these keys to encrypt data exchanged between them.Figure 98 WPA(2)-PSK AuthenticationSecurity Parameters SummaryRefer to this table to see what other security parameters you should configure for each authentication method or key management protocol type. MAC address filters are not dependent on how you configure these security features.Antenna OverviewAn antenna couples RF signals onto air. A transmitter within a wireless device sends an RF signal to the antenna, which propagates the signal through the air. The antenna also operates in reverse by capturing RF signals from the air. Table 60 Wireless Security Relational MatrixAUTHENTICATION METHOD/ KEY MANAGEMENT PROTOCOLENCRYPTION METHOD ENTER MANUAL KEY IEEE 802.1XOpen None No DisableEnable without Dynamic WEP KeyOpen WEP No Enable with Dynamic WEP KeyYes Enable without Dynamic WEP KeyYes DisableShared WEP No Enable with Dynamic WEP KeyYes Enable without Dynamic WEP KeyYes DisableWPA TKIP/AES No EnableWPA-PSK TKIP/AES Yes DisableWPA2 TKIP/AES No EnableWPA2-PSK TKIP/AES Yes Disable
Appendix D Wireless LANsWAP5605 User’s Guide 175Positioning the antennas properly increases the range and coverage area of a wireless LAN. Antenna CharacteristicsFrequencyAn antenna in the frequency of 5GHz is needed to communicate efficiently in a wireless LAN.Radiation PatternA radiation pattern is a diagram that allows you to visualize the shape of the antenna’s coverage area. Antenna GainAntenna gain, measured in dB (decibel), is the increase in coverage within the RF beam width. Higher antenna gain improves the range of the signal for better communications. For an indoor site, each 1 dB increase in antenna gain results in a range increase of approximately 2.5%. For an unobstructed outdoor site, each 1dB increase in gain results in a range increase of approximately 5%. Actual results may vary depending on the network environment. Antenna gain is sometimes specified in dBi, which is how much the antenna increases the signal power compared to using an isotropic antenna. An isotropic antenna is a theoretical perfect antenna that sends out radio signals equally well in all directions. dBi represents the true gain that the antenna provides. Types of Antennas for WLANThere are two types of antennas used for wireless LAN applications.• Omni-directional antennas send the RF signal out in all directions on a horizontal plane. The coverage area is torus-shaped (like a donut) which makes these antennas ideal for a room environment. With a wide coverage area, it is possible to make circular overlapping coverage areas with multiple access points. • Directional antennas concentrate the RF signal in a beam, like a flashlight does with the light from its bulb. The angle of the beam determines the width of the coverage pattern. Angles typically range from 20 degrees (very directional) to 120 degrees (less directional). Directional antennas are ideal for hallways and outdoor point-to-point applications.Positioning AntennasIn general, antennas should be mounted as high as practically possible and free of obstructions. In point-to–point application, position both antennas at the same height and in a direct line of sight to each other to attain the best performance. For omni-directional antennas mounted on a table, desk, and so on, point the antenna up. For omni-directional antennas mounted on a wall or ceiling, point the antenna down. For a single AP application, place omni-directional antennas as close to the center of the coverage area as possible. For directional antennas, point the antenna in the direction of the desired coverage area.
Appendix D Wireless LANsWAP5605 User’s Guide176
WAP5605 User’s Guide 177APPENDIX ECommon ServicesThe following table lists some commonly-used services and their associated protocols and port numbers. For a comprehensive list of port numbers, ICMP type/code numbers and services, visit the IANA (Internet Assigned Number Authority) web site. •Name: This is a short, descriptive name for the service. You can use this one or create a different one, if you like.•Protocol: This is the type of IP protocol used by the service. If this is TCP/UDP, then the service uses the same port number with TCP and UDP. If this is USER-DEFINED, the Port(s) is the IP protocol number, not the port number.•Port(s): This value depends on the Protocol. Please refer to RFC 1700 for further information about port numbers.•If the Protocol is TCP, UDP, or TCP/UDP, this is the IP port number.•If the Protocol is USER, this is the IP protocol number.•Description: This is a brief explanation of the applications that use this service or the situations in which this service is used.Table 61 Commonly Used ServicesNAME PROTOCOL PORT(S) DESCRIPTIONAH (IPSEC_TUNNEL)User-Defined 51 The IPSEC AH (Authentication Header) tunneling protocol uses this service.AIM/New-ICQ TCP 5190 AOL’s Internet Messenger service. It is also used as a listening port by ICQ.AUTH TCP 113 Authentication protocol used by some servers.BGP TCP 179 Border Gateway Protocol.BOOTP_CLIENT UDP 68 DHCP Client.BOOTP_SERVER UDP 67 DHCP Server.CU-SEEME TCPUDP764824032A popular videoconferencing solution from White Pines Software.DNS TCP/UDP 53 Domain Name Server, a service that matches web names (for example www.zyxel.com) to IP numbers.ESP (IPSEC_TUNNEL)User-Defined 50 The IPSEC ESP (Encapsulation Security Protocol) tunneling protocol uses this service.FINGER TCP 79 Finger is a UNIX or Internet related command that can be used to find out if a user is logged on.FTP TCPTCP2021File Transfer Program, a program to enable fast transfer of files, including large files that may not be possible by e-mail.H.323 TCP 1720 NetMeeting uses this protocol.
Appendix E Common ServicesWAP5605 User’s Guide178HTTP TCP 80 Hyper Text Transfer Protocol - a client/server protocol for the world wide web.HTTPS TCP 443 HTTPS is a secured http session often used in e-commerce.ICMP User-Defined 1Internet Control Message Protocol is often used for diagnostic or routing purposes.ICQ UDP 4000 This is a popular Internet chat program.IGMP (MULTICAST) User-Defined 2Internet Group Management Protocol is used when sending packets to a specific group of hosts.IKE UDP 500 The Internet Key Exchange algorithm is used for key distribution and management.IRC TCP/UDP 6667 This is another popular Internet chat program.MSN Messenger TCP 1863 Microsoft Networks’ messenger service uses this protocol. NEW-ICQ TCP 5190 An Internet chat program.NEWS TCP 144 A protocol for news groups.NFS UDP 2049 Network File System - NFS is a client/server distributed file service that provides transparent file sharing for network environments.NNTP TCP 119 Network News Transport Protocol is the delivery mechanism for the USENET newsgroup service.PING User-Defined 1Packet INternet Groper is a protocol that sends out ICMP echo requests to test whether or not a remote host is reachable.POP3 TCP 110 Post Office Protocol version 3 lets a client computer get e-mail from a POP3 server through a temporary connection (TCP/IP or other).PPTP TCP 1723 Point-to-Point Tunneling Protocol enables secure transfer of data over public networks. This is the control channel.PPTP_TUNNEL (GRE)User-Defined 47 PPTP (Point-to-Point Tunneling Protocol) enables secure transfer of data over public networks. This is the data channel.RCMD TCP 512 Remote Command Service.REAL_AUDIO TCP 7070 A streaming audio service that enables real time sound over the web.REXEC TCP 514 Remote Execution Daemon.RLOGIN TCP 513 Remote Login.RTELNET TCP 107 Remote Telnet.RTSP TCP/UDP 554 The Real Time Streaming (media control) Protocol (RTSP) is a remote control for multimedia on the Internet. SFTP TCP 115 Simple File Transfer Protocol.Table 61 Commonly Used Services (continued)NAME PROTOCOL PORT(S) DESCRIPTION
Appendix E Common ServicesWAP5605 User’s Guide 179SMTP TCP 25 Simple Mail Transfer Protocol is the message-exchange standard for the Internet. SMTP enables you to move messages from one e-mail server to another.SNMP TCP/UDP 161 Simple Network Management Program.SNMP-TRAPS TCP/UDP 162 Traps for use with the SNMP (RFC:1215).SQL-NET TCP 1521 Structured Query Language is an interface to access data on many different types of database systems, including mainframes, midrange systems, UNIX systems and network servers.SSH TCP/UDP 22 Secure Shell Remote Login Program.STRM WORKS UDP 1558 Stream Works Protocol.SYSLOG UDP 514 Syslog allows you to send system logs to a UNIX server.TACACS UDP 49 Login Host Protocol used for (Terminal Access Controller Access Control System).TELNET TCP 23 Telnet is the login and terminal emulation protocol common on the Internet and in UNIX environments. It operates over TCP/IP networks. Its primary function is to allow users to log into remote host systems.TFTP UDP 69 Trivial File Transfer Protocol is an Internet file transfer protocol similar to FTP, but uses the UDP (User Datagram Protocol) rather than TCP (Transmission Control Protocol).VDOLIVE TCP 7000 Another videoconferencing solution.Table 61 Commonly Used Services (continued)NAME PROTOCOL PORT(S) DESCRIPTION
Appendix E Common ServicesWAP5605 User’s Guide180
WAP5605 User’s Guide 181APPENDIX FOpen Software AnnouncementsEnd-User License Agreement for "WAP5605" WARNING: ZyXEL Communications Corp. IS WILLING TO LICENSE THE SOFTWARE TO YOU ONLY UPON THE CONDITION THAT YOU ACCEPT ALL OF THE TERMS CONTAINED IN THIS LICENSE AGREEMENT. PLEASE READ THE TERMS CAREFULLY BEFORE COMPLETING THE INSTALLATION PROCESS AS INSTALLING THE SOFTWARE WILL INDICATE YOUR ASSENT TO THEM. IF YOU DO NOT AGREE TO THESE TERMS, THEN ZyXEL IS UNWILLING TO LICENSE THE SOFTWARE TO YOU, IN WHICH EVENT YOU SHOULD RETURN THE UNINSTALLED SOFTWARE AND PACKAGING TO THE PLACE FROM WHICH IT WAS ACQUIRED OR ZyXEL, AND YOUR MONEY WILL BE REFUNDED. HOWEVER, CERTAIN ZYXEL'S PRODUCTS MAY CONTAIN-IN PART-SOME THIRD PARTY'S FREE AND OPEN SOFTWARE PROGRAMS WHICH ALLOW YOU TO FREELY COPY, RUN, DISTRIBUTE, MODIFY AND IMPROVE THE SOFTWARE UNDER THE APPLICABLE TERMS OF SUCH THRID PARTY'S LICENSES ("OPEN-SOURCED COMPONENTS"). THE OPEN-SOURCED COMPONENTS ARE LISTED IN THE NOTICE OR APPENDIX BELOW. ZYXEL MAY HAVE DISTRIBUTED TO YOU HARDWARE AND/OR SOFTWARE, OR MADE AVAILABLE FOR ELECTRONIC DOWNLOADS THESE FREE SOFTWARE PROGRAMS OF THRID PARTIES AND YOU ARE LICENSED TO FREELY COPY, MODIFY AND REDISTIBUTE THAT SOFTWARE UNDER THE APPLICABLE LICENSE TERMS OF SUCH THIRD PARTY. NONE OF THE STATEMENTS OR DOCUMENTATION FROM ZYXEL INCLUDING ANY RESTRICTIONS OR CONDITIONS STATED IN THIS END USER LICENSE AGREEMENT SHALL RESTRICT ANY RIGHTS AND LICENSES YOU MAY HAVE WITH RESPECT TO THE OPEN-SOURCED COMPONENTS UNDER THE APPLICABLE LICENSE TERMS OF SUCH THIRD PARTY. 1Grant of License for Personal UseZyXEL Communications Corp. ("ZyXEL") grants you a non-exclusive, non-sublicense, non-transferable license to use the program with which this license is distributed (the "Software"), including any documentation files accompanying the Software ("Documentation"), for internal business use only, for up to the number of users specified in sales order and invoice. You have the right to make one backup copy of the Software and Documentation solely for archival, back-up or disaster recovery purposes. You shall not exceed the scope of the license granted hereunder. Any
Appendix F Open Software AnnouncementsWAP5605 User’s Guide182rights not expressly granted by ZyXEL to you are reserved by ZyXEL, and all implied licenses are disclaimed.2OwnershipYou have no ownership rights in the Software. Rather, you have a license to use the Software as long as this License Agreement remains in full force and effect. Ownership of the Software, Documentation and all intellectual property rights therein shall remain at all times with ZyXEL. Any other use of the Software by any other entity is strictly forbidden and is a violation of this License Agreement.3CopyrightThe Software and Documentation contain material that is protected by international copyright law, trade secret law, international treaty provisions, and the applicable national laws of each respective country. All rights not granted to you herein are expressly reserved by ZyXEL. You may not remove any proprietary notice of ZyXEL or any of its licensors from any copy of the Software or Documentation.4RestrictionsYou may not publish, display, disclose, sell, rent, lease, modify, store, loan, distribute, or create derivative works of the Software, or any part thereof. You may not assign, sublicense, convey or otherwise transfer, pledge as security or otherwise encumber the rights and licenses granted hereunder with respect to the Software. ZyXEL is not obligated to provide any maintenance, technical or other support for the resultant modified Software. You may not copy, reverse engineer, decompile, reverse compile, translate, adapt, or disassemble the Software, or any part thereof, nor shall you attempt to create the source code from the object code for the Software. Except as and only to the extent expressly permitted in this License, you may not market, co-brand, and private label or otherwise permit third parties to link to the Software, or any part thereof. You may not use the Software, or any part thereof, in the operation of a service bureau or for the benefit of any other person or entity. You may not cause, assist or permit any third party to do any of the foregoing. Portions of the Software utilize or include third party software and other copyright material. Acknowledgements, licensing terms and disclaimers for such material are contained in the License Notice as below for the third party software, and your use of such material is exclusively governed by their respective terms. ZyXEL has provided, as part of the Software package, access to certain third party software as a convenience. To the extent that the Software contains third party software, ZyXEL has no express or implied obligation to provide any technical or other support for such software other than compliance with the applicable license terms of such third party, and makes no warranty (express, implied or statutory) whatsoever with respect thereto. Please contact the appropriate software vendor or manufacturer directly for technical support and customer service related to its software and products. 5ConfidentialityYou acknowledge that the Software contains proprietary trade secrets of ZyXEL and you hereby agree to maintain the confidentiality of the Software using at least as great a degree of care as you use to maintain the confidentiality of your own most confidential information. You agree to reasonably communicate the terms and conditions of this License Agreement to those persons employed by you who come into contact with the Software, and to use reasonable best efforts to ensure their compliance with such terms and conditions, including, without limitation, not knowingly permitting such persons to use any portion of the Software for the purpose of deriving the source code of the Software.6No Warranty
Appendix F Open Software AnnouncementsWAP5605 User’s Guide 183THE SOFTWARE IS PROVIDED "AS IS." TO THE MAXIMUM EXTENT PERMITTED BY LAW, ZyXEL DISCLAIMS ALL WARRANTIES OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, WITHOUT LIMITATION, IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT. ZyXEL DOES NOT WARRANT THAT THE FUNCTIONS CONTAINED IN THE SOFTWARE WILL MEET ANY REQUIREMENTS OR NEEDS YOU MAY HAVE, OR THAT THE SOFTWARE WILL OPERATE ERROR FREE, OR IN AN UNINTERUPTED FASHION, OR THAT ANY DEFECTS OR ERRORS IN THE SOFTWARE WILL BE CORRECTED, OR THAT THE SOFTWARE IS COMPATIBLE WITH ANY PARTICULAR PLATFORM. SOME JURISDICTIONS DO NOT ALLOW THE WAIVER OR EXCLUSION OF IMPLIED WARRANTIES SO THEY MAY NOT APPLY TO YOU. IF THIS EXCLUSION IS HELD TO BE UNENFORCEABLE BY A COURT OF COMPETENT JURISDICTION, THEN ALL EXPRESS AND IMPLIED WARRANTIES SHALL BE LIMITED IN DURATION TO A PERIOD OF THIRTY (30) DAYS FROM THE DATE OF PURCHASE OF THE SOFTWARE, AND NO WARRANTIES SHALL APPLY AFTER THAT PERIOD.7Limitation of LiabilityIN NO EVENT WILL ZyXEL BE LIABLE TO YOU OR ANY THIRD PARTY FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES (INCLUDING, WITHOUT LIMITATION, INDIRECT, SPECIAL, PUNITIVE, OR EXEMPLARY DAMAGES FOR LOSS OF BUSINESS, LOSS OF PROFITS, BUSINESS INTERRUPTION, OR LOSS OF BUSINESS INFORMATION) ARISING OUT OF THE USE OF OR INABILITY TO USE THE SOFTWARE OR PROGRAM, OR FOR ANY CLAIM BY ANY OTHER PARTY, EVEN IF ZyXEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. ZyXEL's TOTAL AGGREGATE LIABILITY WITH RESPECT TO ITS OBLIGATIONS UNDER THIS AGREEMENT OR OTHERWISE WITH RESPECT TO THE SOFTWARE AND DOCUMENTATION OR OTHERWISE SHALL BE EQUAL TO THE PURCHASE PRICE, BUT SHALL IN NO EVENT EXCEED THE PRODUCT'S PRICE. BECAUSE SOME STATES/COUNTRIES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, THE ABOVE LIMITATION MAY NOT APPLY TO YOU.8Export RestrictionsTHIS LICENSE AGREEMENT IS EXPRESSLY MADE SUBJECT TO ANY APPLICABLE LAWS, REGULATIONS, ORDERS, OR OTHER RESTRICTIONS ON THE EXPORT OF THE SOFTWARE OR INFORMATION ABOUT SUCH SOFTWARE WHICH MAY BE IMPOSED FROM TIME TO TIME. YOU SHALL NOT EXPORT THE SOFTWARE, DOCUMENTATION OR INFORMATION ABOUT THE SOFTWARE AND DOCUMENTATION WITHOUT COMPLYING WITH SUCH LAWS, REGULATIONS, ORDERS, OR OTHER RESTRICTIONS. YOU AGREE TO INDEMNIFY ZyXEL AGAINST ALL CLAIMS, LOSSES, DAMAGES, LIABILITIES, COSTS AND EXPENSES, INCLUDING REASONABLE ATTORNEYS' FEES, TO THE EXTENT SUCH CLAIMS ARISE OUT OF ANY BREACH OF THIS SECTION 8.9Audit RightsZyXEL SHALL HAVE THE RIGHT, AT ITS OWN EXPENSE, UPON REASONABLE PRIOR NOTICE, TO PERIODICALLY INSPECT AND AUDIT YOUR RECORDS TO ENSURE YOUR COMPLIANCE WITH THE TERMS AND CONDITIONS OF THIS LICENSE AGREEMENT.10 TerminationThis License Agreement is effective until it is terminated. You may terminate this License Agreement at any time by destroying or returning to ZyXEL all copies of the Software and Documentation in your possession or under your control. ZyXEL may terminate this License Agreement for any reason, including, but not limited to, if ZyXEL finds that you have violated any of the terms of this License Agreement. Upon notification of termination, you agree to destroy or return to ZyXEL all copies of the Software and Documentation and to certify in writing that all known copies, including backup copies, have been destroyed. All provisions relating to
Appendix F Open Software AnnouncementsWAP5605 User’s Guide184confidentiality, proprietary rights, and non-disclosure shall survive the termination of this Software License Agreement.11 GeneralThis License Agreement shall be construed, interpreted and governed by the laws of Republic of China without regard to conflicts of laws provisions thereof. The exclusive forum for any disputes arising out of or relating to this License Agreement shall be an appropriate court or Commercial Arbitration Association sitting in ROC, Taiwan if the parties agree to a binding arbitration. This License Agreement shall constitute the entire Agreement between the parties hereto. This License Agreement, the rights granted hereunder, the Software and Documentation shall not be assigned by you without the prior written consent of ZyXEL. Any waiver or modification of this License Agreement shall only be effective if it is in writing and signed by both parties hereto. If any part of this License Agreement is found invalid or unenforceable by a court of competent jurisdiction, the remainder of this License Agreement shall be interpreted so as to reasonably effect the intention of the parties.NOTE: Some components of this product incorporate free software programs covered under the open source code licenses which allows you to freely copy, modify and redistribute the software. For at least three (3) years from the date of distribution of the applicable product or software, we will give to anyone who contacts us at the ZyXEL Technical Support (support@zyxel.com.tw), for a charge of no more than our cost of physically performing source code distribution, a complete machine-readable copy of the complete corresponding source code for the version of the Programs that we distributed to you if we are in possession of such. Notice Information herein is subject to change without notice. Companies, names, and data used in examples herein are fictitious unless otherwise noted. No part may be reproduced or transmitted in any form or by any means, electronic or mechanical, for any purpose, except the express written permission of ZyXEL Communications Corporation.This Product includes Linux Kernel , Uboot, Busybox, bridge-utils, iptables, linux-igd, mkimage, mkdosfs, 802.1x, bigpond, bonnie++, ctorrent-dnh, ethtool, gdbserver, iproute2, mtd-utils, ntpclient, ntfs-3g, p910nd, pciutils, pptp-client, rp-12tp, rp-pppoe, rt61apd, samba, stupid-ftpd, ushare, wireless_tools, zebra, igmpproxy, inadyn, matrixssl, Linux IPv6 Router, wpa_supplicant and Lib (uClinux Tool Chain, Linux Tool Chain) under GPL 2.0 license.GNU GENERAL PUBLIC LICENSEVersion 2, June 1991Copyright (C) 1989, 1991 Free Software Foundation, Inc.
Appendix F Open Software AnnouncementsWAP5605 User’s Guide 18559 Temple Place - Suite 330, Boston, MA 02111-1307, USAEveryone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed.PreambleThe licenses for most software are designed to take away your freedom to share and change it. By contrast, the GNU General Public License is intended to guarantee your freedom to share and change free software--to make sure the software is free for all its users. This General Public License applies to most of the Free Software Foundation's software and to any other program whose authors commit to using it. (Some other Free Software Foundation software is covered by the GNU Library General Public License instead.) You can apply it to your programs, too.When we speak of free software, we are referring to freedom, not price. Our General Public Licenses are designed to make sure that you have the freedom to distribute copies of free software (and charge for this service if you wish), that you receive source code or can get it if you want it, that you can change the software or use pieces of it in new free programs; and that you know you can do these things. To protect your rights, we need to make restrictions that forbid anyone to deny you these rights or to ask you to surrender the rights. These restrictions translate to certain responsibilities for you if you distribute copies of the software, or if you modify it. For example, if you distribute copies of such a program, whether gratis or for a fee, you must give the recipients all the rights that you have. You must make sure that they, too, receive or can get the source code. And you must show them these terms so they know their rights.We protect your rights with two steps: (1) copyright the software, and (2) offer you this license which gives you legal permission to copy, distribute and/or modify the software. Also, for each author's protection and ours, we want to make certain that everyone understands that there is no warranty for this free software. If the software is modified by someone else and passed on, we want its recipients to know that what they have is not the original, so that any problems introduced by others will not reflect on the original authors' reputations.Finally, any free program is threatened constantly by software patents. We wish to avoid the danger that redistributors of a free program will individually obtain patent licenses, in effect making the program proprietary. To prevent this, we have made it clear that any patent must be licensed for everyone's free use or not licensed at all.The precise terms and conditions for copying, distribution and modification follow. TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION0. This License applies to any program or other work which contains a notice placed by the copyright holder saying it may be distributed under the terms of this General Public License. The "Program", below, refers to any such program or work, and a "work based on the Program" means either the Program or any derivative work under copyright law: that is to say, a work containing the Program or a portion of it, either verbatim or with modifications and/or translated into another language. (Hereinafter, translation is included without limitation in the term "modification".) Each licensee is addressed as "you". Activities other than copying, distribution and modification are not covered by this License; they are outside its scope. The act of running the Program is not restricted,
Appendix F Open Software AnnouncementsWAP5605 User’s Guide186and the output from the Program is covered only if its contents constitute a work based on the Program (independent of having been made by running the Program). Whether that is true depends on what the Program does. 1. You may copy and distribute verbatim copies of the Program's source code as you receive it, in any medium, provided that you conspicuously and appropriately publish on each copy an appropriate copyright notice and disclaimer of warranty; keep intact all the notices that refer to this License and to the absence of any warranty; and give any other recipients of the Program a copy of this License along with the Program. You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty protection in exchange for a fee.2. You may modify your copy or copies of the Program or any portion of it, thus forming a work based on the Program, and copy and distribute such modifications or work under the terms of Section 1 above, provided that you also meet all of these conditions: a) You must cause the modified files to carry prominent notices stating that you changed the files and the date of any change.b) You must cause any work that you distribute or publish, that in whole or in part contains or is derived from the Program or any part thereof, to be licensed as a whole at no charge to all third parties under the terms of this License. c) If the modified program normally reads commands interactively when run, you must cause it, when started running for such interactive use in the most ordinary way, to print or display an announcement including an appropriate copyright notice and a notice that there is no warranty (or else, saying that you provide a warranty) and that users may redistribute the program under these conditions, and telling the user how to view a copy of this License. (Exception: if the Program itself is interactive but does not normally print such an announcement, your work based on the Program is not required to print an announcement.)These requirements apply to the modified work as a whole. If identifiable sections of that work are not derived from the Program, and can be reasonably considered independent and separate works in themselves, then this License, and its terms, do not apply to those sections when you distribute them as separate works. But when you distribute the same sections as part of a whole which is a work based on the Program, the distribution of the whole must be on the terms of this License, whose permissions for other licensees extend to the entire whole, and thus to each and every part regardless of who wrote it. Thus, it is not the intent of this section to claim rights or contest your rights to work written entirely by you; rather, the intent is to exercise the right to control the distribution of derivative or collective works based on the Program. In addition, mere aggregation of another work not based on the Program with the Program (or with a work based on the Program) on a volume of a storage or distribution medium does not bring the other work under the scope of this License. 3. You may copy and distribute the Program (or a work based on it, under Section 2) in object code or executable form under the terms of Sections 1 and 2 above provided that you also do one of the following: a) Accompany it with the complete corresponding machine-readable source code, which must be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software interchange; or, b) Accompany it with a written offer, valid for at least three years, to give any third party, for a charge no more than your cost of physically performing source distribution, a complete machine-readable copy of the corresponding source code, to be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software interchange; or, c) Accompany it with the
Appendix F Open Software AnnouncementsWAP5605 User’s Guide 187information you received as to the offer to distribute corresponding source code. (This alternative is allowed only for noncommercial distribution and only if you received the program in object code or executable form with such an offer, in accord with Subsection b above.) The source code for a work means the preferred form of the work for making modifications to it. For an executable work, complete source code means all the source code for all modules it contains, plus any associated interface definition files, plus thescripts used to control compilation and installation of the executable. However, as a special exception, the source code distributed need not include anything that is normally distributed (in either source or binary form) with the major components (compiler, kernel, and so on) of the operating system on which the executable runs, unless that component itself accompanies the executable. If distribution of executable or object code is made by offering access to copy from a designated place, then offering equivalent access to copy the source code from the same place counts as distribution of the source code, even though third parties are not compelled to copy the source along with the object code. 4. You may not copy, modify, sublicense, or distribute the Program except as expressly provided under this License. Any attempt otherwise to copy, modify, sublicense or distribute the Program is void, and will automatically terminate your rights under this License. However, parties who have received copies, or rights, from you under this License will not have their licenses terminated so long as such parties remain in full compliance.5. You are not required to accept this License, since you have not signed it. However, nothing else grants you permission to modify or distribute the Program or its derivative works. These actions are prohibited by law if you do not accept this License. Therefore, by modifying or distributing the Program (or any work based on the Program), you indicate your acceptance of this License to do so, and all its terms and conditions for copying, distributing or modifying the Program or works based on it. 6. Each time you redistribute the Program (or any work based on the Program), the recipient automatically receives a license from the original licensor to copy, distribute or modify the Program subject to these terms and conditions. You may not impose any further restrictions on the recipients' exercise of the rights granted herein. You are not responsible for enforcing compliance by third parties to this License.7. If, as a consequence of a court judgment or allegation of patent infringement or for any other reason (not limited to patent issues), conditions are imposed on you (whether by court order, agreement or otherwise) that contradict the conditions of this License, they do not excuse you from the conditions of this License. If you cannot distribute so as to satisfy simultaneously your obligations under this License and any other pertinent obligations, then as a consequence you may not distribute the Program at all. For example, if a patent license would not permit royalty-free redistribution of the Program by all those who receive copies directly or indirectly through you, then the only way you could satisfy both it and this License would be to refrain entirely from distribution of the Program. If any portion of this section is held invalid or unenforceable under any particular circumstance, the balance of the section is intended to apply and the section as a whole is intended to apply in other circumstances. It is not the purpose of this section to induce you to infringe any patents or other property right claims or to contest validity of any such claims; this section has the sole purpose of protecting the integrity of the free software distribution system, which is implemented by public license practices. Many people have made generous contributions to the wide range of software distributed through that system in reliance on consistent application of that system; it is up to the author/donor to decide if he or she is willing to distribute software through any other system and a licensee cannot impose that choice. This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this License.
Appendix F Open Software AnnouncementsWAP5605 User’s Guide1888. If the distribution and/or use of the Program is restricted in certain countries either by patents or by copyrighted interfaces, the original copyright holder who places the Program under this License may add an explicit geographical distribution limitation excluding those countries, so that distribution is permitted only in or among countries not thus excluded. In such case, this License incorporates the limitation as if written in the body of this License.9. The Free Software Foundation may publish revised and/or new versions of the General Public License from time to time. Such new versions will be similar in spirit to the present version, but may differ in detail to address new problems or concerns. Each version is given a distinguishing version number. If the Program specifies a version number of this License which applies to it and "any later version", you have the option of following the terms and conditions either of that version or of any later version published by the Free Software Foundation. If the Program does not specify a version number of this License, you may choose any version ever published by the Free Software Foundation.10. If you wish to incorporate parts of the Program into other free programs whose distribution conditions are different, write to the author to ask for permission. For software which is copyrighted by the Free Software Foundation, write to the Free Software Foundation; we sometimes make exceptions for this. Our decision will be guided by the two goals of preserving the free status of all derivatives of our free software and of promoting the sharing and reuse of software generally.NO WARRANTY11. BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY FOR THE PROGRAM, TO THE EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE PROGRAM "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE PROGRAM IS WITH YOU. SHOULD THE PROGRAM PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION.12. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE THE PROGRAM AS PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE PROGRAM (INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE PROGRAM TO OPERATE WITH ANY OTHER PROGRAMS), EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. END OF TERMS AND CONDITIONSAll other trademarks or trade names mentioned herein, if any, are the property of their respective owners.This Product includes Imbench software under below license
Appendix F Open Software AnnouncementsWAP5605 User’s Guide 189The set of programs and documentation known as "lmbench" are distributed under the Free Software Foundation's General Public License with the following additional restrictions (which override any conflicting restrictions in the GPL): 1. You may not distribute results in any public forum, in any publication, or in any other way if you have modified the benchmarks. 2. You may not distribute the results for a fee of any kind. This includes web sites which generate revenue from advertising. If you have modifications or enhancements that you wish included in future versions, please mail those to me, Larry McVoy, at lm@bitmover.com. =========================================================================Rationale for the publication restrictions: In summary: a) LMbench is designed to measure enough of an OS that if you do well in all catagories, you've covered latency and bandwidth in networking, disks, file systems, VM systems, and memory systems. b) Multiple times in the past people have wanted to report partial results. Without exception, they were doing so to show a skewed view of whatever it was they were measuring (for example, one OS fit small processes into segments and used the segment register to switch them, getting good results, but did not want to report large process context switches because those didn't look as good). c) We insist that if you formally report LMbench results, you have to report all of them and make the raw results file easily available. Reporting all of them means in that same publication, a pointer does not count. Formally, in this context, means in a paper, on a web site, etc., but does not mean the exchange of results between OS developers who are tuning a particular subsystem. We have a lot of history with benchmarking and feel strongly that there is little to be gained and a lot to be lost if we allowed the results to be published in isolation, without the complete story being told.
Appendix F Open Software AnnouncementsWAP5605 User’s Guide190There has been a lot of discussion about this, with people not liking this restriction, more or less on the freedom principle as far as I can tell. We're not swayed by that, our position is that we are doing the right thing for the OS community and will stick to our guns on this one. It would be a different matter if there were 3 other competing benchmarking systems out there that did what LMbench does and didn't have the same reporting rules. There aren't and as long as that is the case, I see no reason to change my mind and lots of reasons not to do so. I'm sorry if I'm a pain in the ass on this topic, but I'm doing the right thing for you and the sooner people realize that the sooner we can get on to real work. Operating system design is a largely an art of balancing tradeoffs. In many cases improving one part of the system has negative effects on other parts of the system. The art is choosing which parts to optimize and which to not optimize. Just like in computer architecture, you can optimize the common instructions (RISC) or the uncommon instructions (CISC), but in either case there is usually a cost to pay (in RISC uncommon instructions are more expensive than common instructions, and in CISC common instructions are more expensive than required). The art lies in knowing which operations are important and optmizing those while minimizing the impact on the rest of the system. Since lmbench gives a good overview of many important system features, users may see the performance of the system as a whole, and can see where tradeoffs may have been made. This is the driving force behind the publication restriction: any idiot can optimize certain subsystems while completely destroying overall system performance. If said idiot publishes *only* the numbers relating to the optimized subsystem, then the costs of the optimization are hidden and readers will mistakenly believe that the optimization is a good idea. By including the publication restriction readers would be able to detect that the optimization improved the subsystem performance while damaging the rest of the system performance and would be able to make an informed decision as to the merits of the optimization. Note that these restrictions only apply to *publications*. We intend and encourage lmbench's use during design, development,and tweaking of systems and applications. If you are tuning the linux or BSD TCP stack, then by all means, use the networkingbenchmarks to evaluate the performance effects of various modifications; Swap results with other developers; use thenetworking numbers in isolation. The restrictions only kick in when you go to *publish* the results. If you sped up theTCP stack by a factor of 2 and want to publish a paper with the various tweaks or algorithms used to accomplish this goal, thenyou can publish the networking numbers to show the improvement. However, the paper *must* also include the rest of the standardlmbench numbers to show how your tweaks may (or may not) have impacted the rest of the system. The full set of numbers may
Appendix F Open Software AnnouncementsWAP5605 User’s Guide 191be included in an appendix, but they *must* be included in the paper. This helps protect the community from adopting flawed technologies based on incomplete data. It also helps protect the community from misleading marketing which tries to sell systems based on partial (skewed) lmbench performance results. We have seen many cases in the past where partial or misleading benchmark results have caused great harm to the community, andwe want to ensure that our benchmark is not used to perpetrate further harm and support false or misleading claims.This Product includes goahead software under below licenseLicense Agreement THIS LICENSE ALLOWS ONLY THE LIMITED USE OF GO AHEAD SOFTWARE,INC. PROPRIETARY CODE. PLEASE CAREFULLY READ THIS AGREEMENT AS ITPERTAINS TO THIS LICENSE, YOU CERTIFY THAT YOU WILL USE THE SOFTWAREONLY IN THE MANNER PERMITTED HEREIN.1. Definitions. 1.1 "Documentation" means any documentation GoAhead includes with theOriginal Code.1.2 "GoAhead" means Go Ahead Software, Inc. 1.3 "Intellectual Property Rights" means all rights, whether now existingor hereinafter acquired, in and to trade secrets, patents, copyrights,
Appendix F Open Software AnnouncementsWAP5605 User’s Guide192trademarks, know-how, as well as moral rights and similar rights of anytype under the laws of any governmental authority, domestic or foreign,including rights in and to all applications and registrations relatingto any of the foregoing.1.4 "License" or "Agreement" means this document. 1.5 "Modifications" means any addition to or deletion from the substanceor structure of either the Original Code or any previous Modifications.1.6 "Original Code" means the Source Code to GoAhead? proprietarycomputer software entitled GoAhead WebServer.1.7 "Response Header" means the first portion of the response messageoutput by the GoAhead WebServer, containing but not limited to, headerfields for date, content-type, server identification and cache control.1.8 "Server Identification Field" means the field in the Response Headerwhich contains the text "Server: GoAhead-Webs".1.9 "You" means an individual or a legal entity exercising rights under,and complying with all of the terms of, this license or a future versionof this license. For legal entities, "You" includes any entity whichcontrols, is controlled by, or is under common control with You. Forpurposes of this definition, "control" means (a) the power, direct orindirect, to cause the direction or management of such entity, whetherby contract or otherwise, or (b) ownership of fifty percent (50%) ormore of the outstanding shares or beneficial ownership of such entity.
Appendix F Open Software AnnouncementsWAP5605 User’s Guide 1932. Source Code License. 2.1 Limited Source Code Grant. GoAhead hereby grants You a world-wide, royalty-free, non-exclusivelicense, subject to third party intellectual property claims, to use,reproduce, modify, copy and distribute the Original Code.2.2 Binary Code. GoAhead hereby grants You a world-wide, royalty-free, non-exclusivelicense to copy and distribute the binary code versions of the OriginalCode together with Your Modifications.2.3 License Back to GoAhead. You hereby grant in both source code and binary code to GoAhead aworld-wide, royalty-free, non-exclusive license to copy, modify, display,use and sublicense any Modifications You make that are distributed orplanned for distribution. Within 30 days of either such event, Youagree to ship to GoAhead a file containing the Modifications (in a mediato be determined by the parties), including any programmers?notes andother programmers?materials. Additionally, You will provide to GoAheada complete description of the product, the product code or model number,the date on which the product is initially shipped, and a contact name,phone number and e-mail address for future correspondence. GoAhead willkeep confidential all data specifically marked as such.
Appendix F Open Software AnnouncementsWAP5605 User’s Guide1942.4 Restrictions on Use. You may sublicense Modifications to third parties such as subcontractorsor OEM's provided that You enter into license agreements with such thirdparties that bind such third parties to all the obligations under thisAgreement applicable to you and that are otherwise substantially similarin scope and application to this Agreement.3. Term. This Agreement and license are effective from the time You accept theterms of this Agreement until this Agreement is terminated. You mayterminate this Agreement at any time by uninstalling or destroyingall copies of the Original Code including any and all binary versionsand removing any Modifications to the Original Code existing in anyproducts. This Agreement will terminate immediately and without furthernotice if You fail to comply with any provision of this Agreement. Allrestrictions on use, and all other provisions that may reasonablybe interpreted to survive termination of this Agreement, will survivetermination of this Agreement for any reason. Upon termination, You agreeto uninstall or destroy all copies of the Original Code, Modifications,and Documentation.4. Trademarks and Brand. 4.1 License and Use.
Appendix F Open Software AnnouncementsWAP5605 User’s Guide 195GoAhead hereby grants to You a limited world-wide, royalty-free,non-exclusive license to use the GoAhead trade names, trademarks, logos,service marks and product designations posted in Exhibit A (collectively,the "GoAhead Marks") in connection with the activities by You under thisAgreement. Additionally, GoAhead grants You a license under the termsabove to such GoAhead trademarks as shall be identified at a URL (the"URL") provided by GoAhead. The use by You of GoAhead Marks shall be inaccordance with GoAhead? trademark policies regarding trademark usageas established at the web site designated by the URL, or as otherwisecommunicated to You by GoAhead at its sole discretion. You understand andagree that any use of GoAhead Marks in connection with this Agreementshall not create any right, title or interest in or to such GoAheadMarks and that all such use and goodwill associated with GoAhead Markswill inure to the benefit of GoAhead.4.2 Promotion by You of GoAhead WebServer Mark. In consideration for the licenses granted by GoAhead to You herein, Youagree to notify GoAhead when You incorporate the GoAhead WebServer inYour product and to inform GoAhead when such product begins to ship. Youagree to promote the Original Code by prominently and visibly displayinga graphic of the GoAhead WebServer mark on the initial web page of Yourproduct that is displayed each time a user connects to it. You also agreethat GoAhead may identify your company as a user of the GoAhead WebServerin conjunction with its own marketing efforts. You may further promotethe Original Code by displaying the GoAhead WebServer mark in marketingand promotional materials such as the home page of your web site or webpages promoting the product.
Appendix F Open Software AnnouncementsWAP5605 User’s Guide1964.3 Placement of Copyright Notice by You. You agree to include copies of the following notice (the "Notice")regarding proprietary rights in all copies of the products that Youdistribute, as follows: (i) embedded in the object code; and (ii) onthe title pages of all documentation. Furthermore, You agree to usecommercially reasonable efforts to cause any licensees of your productsto embed the Notice in object code and on the title pages or relevantdocumentation. The Notice is as follows: Copyright (c) 20xx GoAheadSoftware, Inc. All Rights Reserved. Unless GoAhead otherwise instructs,the year 20xx is to be replaced with the year during which the release ofthe Original Code containing the notice is issued by GoAhead. If this yearis not supplied with Documentation, GoAhead will supply it upon request.4.4 No Modifications to Server Identification Field. You agree not to remove or modify the Server identification Fieldcontained in the Response Header as defined in Section 1.6 and 1.7.5. Warranty Disclaimers. THE ORIGINAL CODE, THE DOCUMENTATION AND THE MEDIA UPON WHICH THE ORIGINALCODE IS RECORDED (IF ANY) ARE PROVIDED "AS IS" AND WITHOUT WARRANTIES OFANY KIND, EXPRESS, STATUTORY OR IMPLIED, INCLUDING, BUT NOT LIMITED TO,THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULARPURPOSE.
Appendix F Open Software AnnouncementsWAP5605 User’s Guide 197The entire risk as to the quality and performance of the Original Code(including any Modifications You make) and the Documentation is withYou. Should the Original Code or the Documentation prove defective,You (and not GoAhead or its distributors, licensors or dealers) assumethe entire cost of all necessary servicing or repair. GoAhead does notwarrant that the functions contained in the Original Code will meet yourrequirements or operate in the combination that You may select for use,that the operation of the Original Code will be uninterrupted or errorfree, or that defects in the Original Code will be corrected. No oralor written statement by GoAhead or by a representative of GoAhead shallcreate a warranty or increase the scope of this warranty.GOAHEAD DOES NOT WARRANT THE ORIGINAL CODE AGAINST INFRINGEMENT OR THELIKE WITH RESPECT TO ANY COPYRIGHT, PATENT, TRADE SECRET, TRADEMARKOR OTHER PROPRIETARY RIGHT OF ANY THIRD PARTY AND DOES NOT WARRANTTHAT THE ORIGINAL CODE DOES NOT INCLUDE ANY VIRUS, SOFTWARE ROUTINEOR OTHER SOFTWARE DESIGNED TO PERMIT UNAUTHORIZED ACCESS, TO DISABLE,ERASE OR OTHERWISE HARM SOFTWARE, HARDWARE OR DATA, OR TO PERFORM ANYOTHER SUCH ACTIONS.Any warranties that by law survive the foregoing disclaimers shallterminate ninety (90) days from the date You received the Original Code.6. Limitation of Liability. YOUR SOLE REMEDIES AND GOAHEAD'S ENTIRE LIABILITY ARE SET FORTH ABOVE. INNO EVENT WILL GOAHEAD OR ITS DISTRIBUTORS OR DEALERS BE LIABLE FORDIRECT, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM
Appendix F Open Software AnnouncementsWAP5605 User’s Guide198THE USE OF THE ORIGINAL CODE, THE INABILITY TO USE THE ORIGINAL CODE,OR ANY DEFECT IN THE ORIGINAL CODE, INCLUDING ANY LOST PROFITS, EVEN IFTHEY HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.You agree that GoAhead and its distributors and dealers will not beLIABLE for defense or indemnity with respect to any claim against Youby any third party arising from your possession or use of the OriginalCode or the Documentation.In no event will GoAhead? total liability to You for all damages, losses,and causes of action (whether in contract, tort, including negligence,or otherwise) exceed the amount You paid for this product.SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTYLASTS, AND SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATIONOF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATIONS OREXCLUSIONS MAY NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGALRIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE.7. Indemnification by You. You agree to indemnify and hold GoAhead harmless against any and allclaims, losses, damages and costs (including legal expenses and reasonablecounsel fees) arising out of any claim of a third party with respect tothe contents of the Your products, and any intellectual property rightsor other rights or interests related thereto.8. High Risk Activities.
Appendix F Open Software AnnouncementsWAP5605 User’s Guide 199The Original Code is not fault-tolerant and is not designed , manufacturedor intended for use or resale as online control equipment in hazardousenvironments requiring fail-safe performance, such as in the operationof nuclear facilities, aircraft navigation or communication systems,air traffic control, direct life support machines or weapons systems,in which the failure of the Original Code could lead directly to death,personal injury, or severe physical or environmental damage. GoAhead andits suppliers specifically disclaim any express or implied warranty offitness for any high risk uses listed above.9. Government Restricted Rights. For units of the Department of Defense, use, duplication, or disclosureby the Government is subject to restrictions as set forth in subparagraph(c)(1)(ii) of the Rights in Technical Data and Computer Software clauseat DFARS 252.227-7013. Contractor/manufacturer is GoAhead Software,Inc., 10900 N.E. 8th Street, Suite 750, Bellevue, Washington 98004.If the Commercial Computer Software Restricted rights clause at FAR52.227-19 or its successors apply, the Software and Documentationconstitute restricted computer software as defined in that clause andthe Government shall not have the license for published software setforth in subparagraph (c)(3) of that clause.The Original Code (i) was developed at private expense, and no part of itwas developed with governmental funds; (ii) is a trade secret of GoAhead(or its licensor(s)) for all purposes of the Freedom of Information Act;
Appendix F Open Software AnnouncementsWAP5605 User’s Guide200(iii) is "restricted computer software" subject to limited utilization asprovided in the contract between the vendor and the governmental entity;and (iv) in all respects is proprietary data belonging solely to GoAhead(or its licensor(s)).10. Governing Law and Interpretation. This Agreement shall be interpreted under and governed by the laws of theState of Washington, without regard to its rules governing the conflict oflaws. If any provision of this Agreement is held illegal or unenforceableby a court or tribunal of competent jurisdiction, the remaining provisionsof this Agreement shall remain in effect and the invalid provision deemedmodified to the least degree necessary to remedy such invalidity.11. Entire Agreement. This Agreement is the complete agreement between GoAhead and You andsupersedes all prior agreements, oral or written, with respect to thesubject matter hereof.If You have any questions concerning this Agreement, You may write toGoAhead Software, Inc., 10900 N.E. 8th Street, Suite 750, Bellevue,Washington 98004 or send e-mail to info@goahead.com.BY CLICKING ON THE "Register" BUTTON ON THE REGISTRATION FORM, YOUACCEPT AND AGREE TO BE BOUND BY ALL OF THE TERMS AND CONDITIONS SETFORTH IN THIS AGREEMENT. IF YOU DO NOT WISH TO ACCEPT THIS LICENSE ORYOU DO NOT QUALIFY FOR A LICENSE BASED ON THE TERMS SET FORTH ABOVE,
Appendix F Open Software AnnouncementsWAP5605 User’s Guide 201YOU MUST NOT CLICK THE "Register" BUTTON.Exhibit A GoAhead Trademarks, Logos, and Product Designation Information 01/28/00This Product includes uClibc, uClibc++ and dhcp6 software under LGPL 2.1 licenseGNU LESSER GENERAL PUBLIC LICENSEVersion 2.1, February 1999 Copyright (C) 1991, 1999 Free Software Foundation, Inc.51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USAEveryone is permitted to copy and distribute verbatim copiesof this license document, but changing it is not allowed.[This is the first released version of the Lesser GPL. It also counts as the successor of the GNU Library Public License, version 2, hence the version number 2.1.]PreambleThe licenses for most software are designed to take away your freedom to share and change it. By contrast, the GNU General Public Licenses are intended to guarantee your freedom to share and change free software--to make sure the software is free for all its users. This license, the Lesser General Public License, applies to some specially designated software packages--typically libraries--of the Free Software Foundation and other authors who decide to use it. You can use it too, but we suggest you first think carefully about whether this license or the ordinary General Public License is the better strategy to use in any particular case, based on the explanations below. When we speak of free software, we are referring to freedom of use, not price. Our General Public Licenses are designed to make sure that you have the freedom to distribute copies of free software (and charge for this service if you wish); that you receive source code or can get it if you want it;
Appendix F Open Software AnnouncementsWAP5605 User’s Guide202that you can change the software and use pieces of it in new free programs; and that you are informed that you can do these things. To protect your rights, we need to make restrictions that forbid distributors to deny you these rights or to ask you to surrender these rights. These restrictions translate to certain responsibilities for you if you distribute copies of the library or if you modify it. For example, if you distribute copies of the library, whether gratis or for a fee, you must give the recipients all the rights that we gave you. You must make sure that they, too, receive or can get the source code. If you link other code with the library, you must provide complete object files to the recipients, so that they can relink them with the library after making changes to the library and recompiling it. And you must show them these terms so they know their rights. We protect your rights with a two-step method: (1) we copyright the library, and (2) we offer you this license, which gives you legal permission to copy, distribute and/or modify the library. To protect each distributor, we want to make it very clear that there is no warranty for the free library. Also, if the library is modified by someone else and passed on, the recipients should know that what they have is not the original version, so that the original author's reputation will not be affected by problems that might be introduced by others. Finally, software patents pose a constant threat to the existence of any free program. We wish to make sure that a company cannot effectively restrict the users of a free program by obtaining a restrictive license from a patent holder. Therefore, we insist that any patent license obtained for a version of the library must be consistent with the full freedom of use specified in this license. Most GNU software, including some libraries, is covered by the ordinary GNU General Public License. This license, the GNU Lesser General Public License, applies to certain designated libraries, and is quite different from the ordinary General Public License. We use this license for certain libraries in order to permit linking those libraries into non-free programs. When a program is linked with a library, whether statically or using a shared library, the combination of the two is legally speaking a combined work, a derivative of the original library. The ordinary General Public License therefore permits such linking only if the entire combination fits its criteria of freedom. The Lesser General Public License permits more lax criteria for linking other code with the library. We call this license the "Lesser" General Public License because it does Less to protect the user's freedom than the ordinary General Public License. It also provides other free software developers Less of an advantage over competing non-free programs. These disadvantages are the reason we use the ordinary General Public License for many libraries. However, the Lesser license provides advantages in certain special circumstances. For example, on rare occasions, there may be a special need to encourage the widest possible use of a certain library, so that it becomes a de-facto standard. To achieve this, non-free programs must be allowed to use the library. A more frequent case is that a free library does the same job as widely used non-free libraries. In this case, there is little to gain by limiting the free library to free software only, so we use the Lesser General Public License. In other cases, permission to use a particular library in non-free programs enables a greater number of people to use a large body of free software. For example, permission to use the GNU C Library in non-free programs enables many more people to use the whole GNU operating system, as well as its variant, the GNU/Linux operating system.
Appendix F Open Software AnnouncementsWAP5605 User’s Guide 203Although the Lesser General Public License is Less protective of the users' freedom, it does ensure that the user of a program that is linked with the Library has the freedom and the wherewithal to run that program using a modified version of the Library. The precise terms and conditions for copying, distribution and modification follow. Pay close attention to the difference between a "work based on the library" and a "work that uses the library". The former contains code derived from the library, whereas the latter must be combined with the library in order to run. TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION0. This License Agreement applies to any software library or other program which contains a notice placed by the copyright holder or other authorized party saying it may be distributed under the terms of this Lesser General Public License (also called "this License"). Each licensee is addressed as "you". A "library" means a collection of software functions and/or data prepared so as to be conveniently linked with application programs (which use some of those functions and data) to form executables. The "Library", below, refers to any such software library or work which has been distributed under these terms. A "work based on the Library" means either the Library or any derivative work under copyright law: that is to say, a work containing the Library or a portion of it, either verbatim or with modifications and/or translated straightforwardly into another language. (Hereinafter, translation is included without limitation in the term "modification".) "Source code" for a work means the preferred form of the work for making modifications to it. For a library, complete source code means all the source code for all modules it contains, plus any associated interface definition files, plus the scripts used to control compilation and installation of the library. Activities other than copying, distribution and modification are not covered by this License; they are outside its scope. The act of running a program using the Library is not restricted, and output from such a program is covered only if its contents constitute a work based on the Library (independent of the use of the Library in a tool for writing it). Whether that is true depends on what the Library does and what the program that uses the Library does. 1. You may copy and distribute verbatim copies of the Library's complete source code as you receive it, in any medium, provided that you conspicuously and appropriately publish on each copy an appropriate copyright notice and disclaimer of warranty; keep intact all the notices that refer to this License and to the absence of any warranty; and distribute a copy of this License along with the Library. You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty protection in exchange for a fee. 2. You may modify your copy or copies of the Library or any portion of it, thus forming a work based on the Library, and copy and distribute such modifications or work under the terms of Section 1 above, provided that you also meet all of these conditions: "a) The modified work must itself be a software library. "b) You must cause the files modified to carry prominent notices stating that you changed the files and the date of any change.
Appendix F Open Software AnnouncementsWAP5605 User’s Guide204"c) You must cause the whole of the work to be licensed at no charge to all third parties under the terms of this License. "d) If a facility in the modified Library refers to a function or a table of data to be supplied by an application program that uses the facility, other than as an argument passed when the facility is invoked, then you must make a good faith effort to ensure that, in the event an application does not supply such function or table, the facility still operates, and performs whatever part of its purpose remains meaningful. (For example, a function in a library to compute square roots has a purpose that is entirely well-defined independent of the application. Therefore, Subsection 2d requires that any application-supplied function or table used by this function must be optional: if the application does not supply it, the square root function must still compute square roots.)These requirements apply to the modified work as a whole. If identifiable sections of that work are not derived from the Library, and can be reasonably considered independent and separate works in themselves, then this License, and its terms, do not apply to those sections when you distribute them as separate works. But when you distribute the same sections as part of a whole which is a work based on the Library, the distribution of the whole must be on the terms of this License, whose permissions for other licensees extend to the entire whole, and thus to each and every part regardless of who wrote it. Thus, it is not the intent of this section to claim rights or contest your rights to work written entirely by you; rather, the intent is to exercise the right to control the distribution of derivative or collective works based on the Library. In addition, mere aggregation of another work not based on the Library with the Library (or with a work based on the Library) on a volume of a storage or distribution medium does not bring the other work under the scope of this License. 3. You may opt to apply the terms of the ordinary GNU General Public License instead of this License to a given copy of the Library. To do this, you must alter all the notices that refer to this License, so that they refer to the ordinary GNU General Public License, version 2, instead of to this License. (If a newer version than version 2 of the ordinary GNU General Public License has appeared, then you can specify that version instead if you wish.) Do not make any other change in these notices. Once this change is made in a given copy, it is irreversible for that copy, so the ordinary GNU General Public License applies to all subsequent copies and derivative works made from that copy. This option is useful when you wish to copy part of the code of the Library into a program that is not a library. 4. You may copy and distribute the Library (or a portion or derivative of it, under Section 2) in object code or executable form under the terms of Sections 1 and 2 above provided that you accompany it with the complete corresponding machine-readable source code, which must be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software interchange. If distribution of object code is made by offering access to copy from a designated place, then offering equivalent access to copy the source code from the same place satisfies the requirement to distribute the source code, even though third parties are not compelled to copy the source along with the object code.
Appendix F Open Software AnnouncementsWAP5605 User’s Guide 2055. A program that contains no derivative of any portion of the Library, but is designed to work with the Library by being compiled or linked with it, is called a "work that uses the Library". Such a work, in isolation, is not a derivative work of the Library, and therefore falls outside the scope of this License. However, linking a "work that uses the Library" with the Library creates an executable that is a derivative of the Library (because it contains portions of the Library), rather than a "work that uses the library". The executable is therefore covered by this License. Section 6 states terms for distribution of such executables. When a "work that uses the Library" uses material from a header file that is part of the Library, the object code for the work may be a derivative work of the Library even though the source code is not. Whether this is true is especially significant if the work can be linked without the Library, or if the work is itself a library. The threshold for this to be true is not precisely defined by law. If such an object file uses only numerical parameters, data structure layouts and accessors, and small macros and small inline functions (ten lines or less in length), then the use of the object file is unrestricted, regardless of whether it is legally a derivative work. (Executables containing this object code plus portions of the Library will still fall under Section 6.) Otherwise, if the work is a derivative of the Library, you may distribute the object code for the work under the terms of Section 6. Any executables containing that work also fall under Section 6, whether or not they are linked directly with the Library itself. 6. As an exception to the Sections above, you may also combine or link a "work that uses the Library" with the Library to produce a work containing portions of the Library, and distribute that work under terms of your choice, provided that the terms permit modification of the work for the customer's own use and reverse engineering for debugging such modifications. You must give prominent notice with each copy of the work that the Library is used in it and that the Library and its use are covered by this License. You must supply a copy of this License. If the work during execution displays copyright notices, you must include the copyright notice for the Library among them, as well as a reference directing the user to the copy of this License. Also, you must do one of these things: "a) Accompany the work with the complete corresponding machine-readable source code for the Library including whatever changes were used in the work (which must be distributed under Sections 1 and 2 above); and, if the work is an executable linked with the Library, with the complete machine-readable "work that uses the Library", as object code and/or source code, so that the user can modify the Library and then relink to produce a modified executable containing the modified Library. (It is understood that the user who changes the contents of definitions files in the Library will not necessarily be able to recompile the application to use the modified definitions.) "b) Use a suitable shared library mechanism for linking with the Library. A suitable mechanism is one that (1) uses at run time a copy of the library already present on the user's computer system, rather than copying library functions into the executable, and (2) will operate properly with a modified version of the library, if the user installs one, as long as the modified version is interface-compatible with the version that the work was made with. "c) Accompany the work with a written offer, valid for at least three years, to give the same user the materials specified in Subsection 6a, above, for a charge no more than the cost of performing this distribution. "d) If distribution of the work is made by offering access to copy from a designated place, offer equivalent access to copy the above specified materials from the same place.
Appendix F Open Software AnnouncementsWAP5605 User’s Guide206"e) Verify that the user has already received a copy of these materials or that you have already sent this user a copy. For an executable, the required form of the "work that uses the Library" must include any data and utility programs needed for reproducing the executable from it. However, as a special exception, the materials to be distributed need not include anything that is normally distributed (in either source or binary form) with the major components (compiler, kernel, and so on) of the operating system on which the executable runs, unless that component itself accompanies the executable. It may happen that this requirement contradicts the license restrictions of other proprietary libraries that do not normally accompany the operating system. Such a contradiction means you cannot use both them and the Library together in an executable that you distribute. 7. You may place library facilities that are a work based on the Library side-by-side in a single library together with other library facilities not covered by this License, and distribute such a combined library, provided that the separate distribution of the work based on the Library and of the other library facilities is otherwise permitted, and provided that you do these two things: "a) Accompany the combined library with a copy of the same work based on the Library, uncombined with any other library facilities. This must be distributed under the terms of the Sections above. "b) Give prominent notice with the combined library of the fact that part of it is a work based on the Library, and explaining where to find the accompanying uncombined form of the same work. 8. You may not copy, modify, sublicense, link with, or distribute the Library except as expressly provided under this License. Any attempt otherwise to copy, modify, sublicense, link with, or distribute the Library is void, and will automatically terminate your rights under this License. However, parties who have received copies, or rights, from you under this License will not have their licenses terminated so long as such parties remain in full compliance. 9. You are not required to accept this License, since you have not signed it. However, nothing else grants you permission to modify or distribute the Library or its derivative works. These actions are prohibited by law if you do not accept this License. Therefore, by modifying or distributing the Library (or any work based on the Library), you indicate your acceptance of this License to do so, and all its terms and conditions for copying, distributing or modifying the Library or works based on it. 10. Each time you redistribute the Library (or any work based on the Library), the recipient automatically receives a license from the original licensor to copy, distribute, link with or modify the Library subject to these terms and conditions. You may not impose any further restrictions on the recipients' exercise of the rights granted herein. You are not responsible for enforcing compliance by third parties with this License. 11. If, as a consequence of a court judgment or allegation of patent infringement or for any other reason (not limited to patent issues), conditions are imposed on you (whether by court order, agreement or otherwise) that contradict the conditions of this License, they do not excuse you from the conditions of this License. If you cannot distribute so as to satisfy simultaneously your obligations under this License and any other pertinent obligations, then as a consequence you may not distribute the Library at all. For example, if a patent license would not permit royalty-free redistribution of the Library by all those who receive copies directly or indirectly through you, then the only way you could satisfy both it and this License would be to refrain entirely from distribution of the Library.
Appendix F Open Software AnnouncementsWAP5605 User’s Guide 207If any portion of this section is held invalid or unenforceable under any particular circumstance, the balance of the section is intended to apply, and the section as a whole is intended to apply in other circumstances. It is not the purpose of this section to induce you to infringe any patents or other property right claims or to contest validity of any such claims; this section has the sole purpose of protecting the integrity of the free software distribution system which is implemented by public license practices. Many people have made generous contributions to the wide range of software distributed through that system in reliance on consistent application of that system; it is up to the author/donor to decide if he or she is willing to distribute software through any other system and a licensee cannot impose that choice. This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this License. 12. If the distribution and/or use of the Library is restricted in certain countries either by patents or by copyrighted interfaces, the original copyright holder who places the Library under this License may add an explicit geographical distribution limitation excluding those countries, so that distribution is permitted only in or among countries not thus excluded. In such case, this License incorporates the limitation as if written in the body of this License. 13. The Free Software Foundation may publish revised and/or new versions of the Lesser General Public License from time to time. Such new versions will be similar in spirit to the present version, but may differ in detail to address new problems or concerns. Each version is given a distinguishing version number. If the Library specifies a version number of this License which applies to it and "any later version", you have the option of following the terms and conditions either of that version or of any later version published by the Free Software Foundation. If the Library does not specify a license version number, you may choose any version ever published by the Free Software Foundation. 14. If you wish to incorporate parts of the Library into other free programs whose distribution conditions are incompatible with these, write to the author to ask for permission. For software which is copyrighted by the Free Software Foundation, write to the Free Software Foundation; we sometimes make exceptions for this. Our decision will be guided by the two goals of preserving the free status of all derivatives of our free software and of promoting the sharing and reuse of software generally. NO WARRANTY 15. BECAUSE THE LIBRARY IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY FOR THE LIBRARY, TO THE EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE LIBRARY "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE LIBRARY IS WITH YOU. SHOULD THE LIBRARY PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION. 16. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE THE LIBRARY AS PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE LIBRARY (INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE LIBRARY
Appendix F Open Software AnnouncementsWAP5605 User’s Guide208TO OPERATE WITH ANY OTHER SOFTWARE), EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. END OF TERMS AND CONDITIONSThe Product contains Portable SDK for UPnP™ Devices distributed under the BSD (Berkeley Standard Distribution) license. Copyright (c) 2000-2003 Intel Corporation All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: * Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. * Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. * Neither name of Intel Corporation nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission. THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL INTEL OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.The Product contains totd software under below license This document contains the copyright notices and licenses that apply to the collection of files that constitute the totd program. As some parts of totd have been produced by other authors than the main author of totd, different parts (files) of totd are copyrighted by multiple authors and are
Appendix F Open Software AnnouncementsWAP5605 User’s Guide 209covered by multiple licences. Each individual file lists its copyright holders, but not the corresponding licenses that apply to it. These licences can be found below. Note that some apply only to (very small) parts of totd, and that all licenses are of the `BSD style'. Note that the SWILL library has its own license. See the SWILL-0.1/ subdirectory for more information. Including the SWILL library into totd is optional.F.W. Dillema Licences======== /* * Copyright (c) Invenia Innovation A.S., Norway. All rights reserved. * * Author: Feike W. Dillema, Invenia Innovation A.S., Norway. * * Permission to use, copy, modify and distribute this software and * its documentation is hereby granted, provided that both the copyright * notice and this permission notice appear in all copies of the * software, derivative works or modified versions, and any portions * thereof, and that both notices appear in supporting documentation. * * INVENIA INNOVATION A.S. ALLOWS FREE USE OF THIS SOFTWARE IN ITS "AS IS" * CONDITION. INVENIA INNOVATION A.S. DISCLAIMS ANY LIABILITY OF ANY KIND * FOR ANY DAMAGES WHATSOEVER RESULTING FROM THE USE OF THIS SOFTWARE. * * The author requests users of this software to send back * any improvements or extensions that they make and grant him and/or * the Invenia Innovation the rights to redistribute these changes without * restrictions.
Appendix F Open Software AnnouncementsWAP5605 User’s Guide210 */ /* * Copyright (c) 1999,2000,2001,2002 University of Tromso, Norway. * All rights reserved. * * Author: Feike W. Dillema, The Pasta Lab, Institutt for Informatikk * University of Tromso, Norway * * Permission to use, copy, modify and distribute this software and * its documentation is hereby granted, provided that both the copyright * notice and this permission notice appear in all copies of the * software, derivative works or modified versions, and any portions * thereof, and that both notices appear in supporting documentation. * * THE UNIVERSITY OF TROMSO ALLOWS FREE USE OF THIS SOFTWARE IN ITS "AS IS" * CONDITION. THE UNIVERSITY OF TROMSO DISCLAIMS ANY LIABILITY OF ANY KIND * FOR ANY DAMAGES WHATSOEVER RESULTING FROM THE USE OF THIS SOFTWARE. * * The author requests users of this software to send back * any improvements or extensions that they make and grant him and/or * the University the rights to redistribute these changes without * restrictions. /* * Copyright (C) 1998 WIDE Project. All rights reserved. * * Redistribution and use in source and binary forms, with or without * modification, are permitted provided that the following conditions
Appendix F Open Software AnnouncementsWAP5605 User’s Guide 211 * are met: * 1. Redistributions of source code must retain the above copyright * notice, this list of conditions and the following disclaimer. * 2. Redistributions in binary form must reproduce the above copyright * notice, this list of conditions and the following disclaimer in the * documentation and/or other materials provided with the distribution. * 3. All advertising materials mentioning features or use of this software * must display the following acknowledgement: * This product includes software developed by WIDE Project and * and its contributors. * 4. Neither the name of the University nor the names of its contributors * may be used to endorse or promote products derived from this software * without specific prior written permission. * * THIS SOFTWARE IS PROVIDED BY THE PROJECT AND CONTRIBUTORS ``AS IS'' AND * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE * ARE DISCLAIMED. IN NO EVENT SHALL THE PROJECT OR CONTRIBUTORS BE LIABLE * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF * SUCH DAMAGE. */ * Copyright (c) 1998 Todd C. Miller <Todd.Miller@courtesan.com>
Appendix F Open Software AnnouncementsWAP5605 User’s Guide212 * All rights reserved. * * Redistribution and use in source and binary forms, with or without * modification, are permitted provided that the following conditions * are met: * 1. Redistributions of source code must retain the above copyright * notice, this list of conditions and the following disclaimer. * 2. Redistributions in binary form must reproduce the above copyright * notice, this list of conditions and the following disclaimer in the * documentation and/or other materials provided with the distribution. * 3. The name of the author may not be used to endorse or promote products * derived from this software without specific prior written permission. * * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, * INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY * AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL * THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, * EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, * PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; * OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, * WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR * OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF * ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. */The Product contains PPP software under below licenseCopyrights:
Appendix F Open Software AnnouncementsWAP5605 User’s Guide 213***********All of the code can be freely used and redistributed. The individual source files each have their own copyright and permission notice; some have a BSD-style notice and some are under the GPL.The Product contains radvd software under below license The author(s) grant permission for redistribution and use in source and binary forms, with or without modification, of the software and documentation provided that the following conditions are met: 0. If you receive a version of the software that is specifically labeled as not being for redistribution (check the version message and/or README), you are not permitted to redistribute that version of the software in any way or form.1. All terms of all other applicable copyrights and licenses must be followed.2. Redistributions of source code must retain the authors' copyright notice(s), this list of conditions, and the following disclaimer.3. Redistributions in binary form must reproduce the authors' copyright notice(s), this list of conditions, and the following disclaimer in the documentation and/or other materials provided with the distribution.4. All advertising materials mentioning features or use of this software must display the following acknowledgement with the name(s) of the authors as specified in the copyright notice(s) substituted where indicated: This product includes software developed by the authors which are mentioned at the start of the source files and other contributors.5. Neither the name(s) of the author(s) nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission. THIS SOFTWARE IS PROVIDED BY ITS AUTHORS AND CONTRIBUTORS ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHORS OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ONANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
Appendix F Open Software AnnouncementsWAP5605 User’s Guide214The Product contains OpenSSL software under below license The OpenSSL toolkit stays under a dual license, i.e. both the conditions of the OpenSSL License and the original SSLeay license apply to the toolkit. See below for the actual license texts. Actually both licenses are BSD-style Open Source licenses. In case of any license issues related to OpenSSL please contact openssl-core@openssl.org.OpenSSL License/* ==================================================================== * Copyright (c) 1998-2007 The OpenSSL Project. All rights reserved. * * Redistribution and use in source and binary forms, with or without * modification, are permitted provided that the following conditions * are met: * * 1. Redistributions of source code must retain the above copyright * notice, this list of conditions and the following disclaimer. * * 2. Redistributions in binary form must reproduce the above copyright * notice, this list of conditions and the following disclaimer in * the documentation and/or other materials provided with the * distribution. * * 3. All advertising materials mentioning features or use of this * software must display the following acknowledgment: * "This product includes software developed by the OpenSSL Project
Appendix F Open Software AnnouncementsWAP5605 User’s Guide 215 * for use in the OpenSSL Toolkit. (http://www.openssl.org/)" * * 4. The names "OpenSSL Toolkit" and "OpenSSL Project" must not be used to * endorse or promote products derived from this software without * prior written permission. For written permission, please contact * openssl-core@openssl.org. * * 5. Products derived from this software may not be called "OpenSSL" * nor may "OpenSSL" appear in their names without prior written * permission of the OpenSSL Project. * * 6. Redistributions of any form whatsoever must retain the following * acknowledgment: * "This product includes software developed by the OpenSSL Project * for use in the OpenSSL Toolkit (http://www.openssl.org/)" * * THIS SOFTWARE IS PROVIDED BY THE OpenSSL PROJECT ``AS IS'' AND ANY * EXPRESSED OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR * PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE OpenSSL PROJECT OR * ITS CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, * SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, * STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED * OF THE POSSIBILITY OF SUCH DAMAGE.
Appendix F Open Software AnnouncementsWAP5605 User’s Guide216 * ==================================================================== * * This product includes cryptographic software written by Eric Young * (eay@cryptsoft.com). This product includes software written by Tim * Hudson (tjh@cryptsoft.com). */Original SSLeay License -----------------------/* Copyright (C) 1995-1998 Eric Young (eay@cryptsoft.com) * All rights reserved. * * This package is an SSL implementation written * by Eric Young (eay@cryptsoft.com). * The implementation was written so as to conform with Netscapes SSL. * * This library is free for commercial and non-commercial use as long as * the following conditions are aheared to. The following conditions * apply to all code found in this distribution, be it the RC4, RSA, * lhash, DES, etc., code; not just the SSL code. The SSL documentation * included with this distribution is covered by the same copyright terms * except that the holder is Tim Hudson (tjh@cryptsoft.com). * * Copyright remains Eric Young's, and as such any Copyright notices in * the code are not to be removed. * If this package is used in a product, Eric Young should be given attribution * as the author of the parts of the library used.
Appendix F Open Software AnnouncementsWAP5605 User’s Guide 217 * This can be in the form of a textual message at program startup or * in documentation (online or textual) provided with the package. * * Redistribution and use in source and binary forms, with or without * modification, are permitted provided that the following conditions * are met: * 1. Redistributions of source code must retain the copyright * notice, this list of conditions and the following disclaimer. * 2. Redistributions in binary form must reproduce the above copyright * notice, this list of conditions and the following disclaimer in the * documentation and/or other materials provided with the distribution. * 3. All advertising materials mentioning features or use of this software * must display the following acknowledgement: * "This product includes cryptographic software written by * Eric Young (eay@cryptsoft.com)" * The word 'cryptographic' can be left out if the rouines from the library * being used are not cryptographic related :-). * 4. If you include any Windows specific code (or a derivative thereof) from * the apps directory (application code) you must include an acknowledgement: * "This product includes software written by Tim Hudson (tjh@cryptsoft.com)" * * THIS SOFTWARE IS PROVIDED BY ERIC YOUNG ``AS IS'' AND * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE * ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
Appendix F Open Software AnnouncementsWAP5605 User’s Guide218 * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF * SUCH DAMAGE. * * The licence and distribution terms for any publically available version or * derivative of this code cannot be changed. i.e. this code cannot simply be * copied and put under another distribution licence * [including the GNU Public Licence.]
WAP5605 User’s Guide 219APPENDIX GLegal InformationCopyrightCopyright © 2011 by ZyXEL Communications Corporation.The contents of this publication may not be reproduced in any part or as a whole, transcribed, stored in a retrieval system, translated into any language, or transmitted in any form or by any means, electronic, mechanical, magnetic, optical, chemical, photocopying, manual, or otherwise, without the prior written permission of ZyXEL Communications Corporation.Published by ZyXEL Communications Corporation. All rights reserved.DisclaimerZyXEL does not assume any liability arising out of the application or use of any products, or software described herein. Neither does it convey any license under its patent rights nor the patent rights of others. ZyXEL further reserves the right to make changes in any products described herein without notice. This publication is subject to change without notice.Certifications Federal Communications Commission (FCC) Interference StatementThe device complies with Part 15 of FCC rules. Operation is subject to the following two conditions:• This device may not cause harmful interference.• This device must accept any interference received, including interference that may cause undesired operations.This device has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This device generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.If this device does cause harmful interference to radio/television reception, which can be determined by turning the device off and on, the user is encouraged to try to correct the interference by one or more of the following measures:1Reorient or relocate the receiving antenna.2Increase the separation between the equipment and the receiver.
Appendix G Legal InformationWAP5605 User’s Guide2203Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.4Consult the dealer or an experienced radio/TV technician for help.FCC Radiation Exposure Statement• This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. • IEEE 802.11n (20MHz) operation of this product in the U.S.A. is firmware-limited to channels 1 through 11. IEEE 802.11n (40MHz) operation of this product in the U.S.A. is firmware-limited to channels 3 through 9. • To comply with FCC RF exposure compliance requirements, a separation distance of at least 20 cm must be maintained between the antenna of this device and all persons. 注意 !依據 低功率電波輻射性電機管理辦法第十二條 經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、加大功率或變更原設計之特性及功能。第十四條 低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立即停用，並改善至無干擾時方得繼續使用。前項合法通信，指依電信規定作業之無線電信。低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。 本機限在不干擾合法電臺與不受被干擾保障條件下於室內使用。 減少電磁波影響，請妥適使用。Notices Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.This device is designed for the WLAN 5 GHz networks throughout the EC region and Switzerland, with restrictions in France.Ce produit est conçu pour les bandes de fréquences 5 GHz conformément à la législation Européenne. En France métropolitaine, suivant les décisions n°03-908 et 03-909 de l’ARCEP, la puissance d’émission ne devra pas dépasser 10 mW (10 dB) dans le cadre d’une installation WiFi en extérieur pour les fréquences comprises entre 2454 MHz et 2483,5 MHz. This Class B digital apparatus complies with Canadian ICES-003.Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
Appendix G Legal InformationWAP5605 User’s Guide 221Industry Canada StatementThis device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions:1this device may not cause interference and2this device must accept any interference, including interference that may cause undesired operation of the deviceThis device has been designed to operate with an antenna having a maximum gain of 2dBi.Antenna having a higher gain is strictly prohibited per regulations of Industry Canada. The required antenna impedance is 50 ohms.To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the EIRP is not more than required for successful communication.IMPORTANT NOTEDevice for the band 5150-5250 MHz is only for indoor usage to reduce potential for harmful interference to co-channel mobile satellite systems; users should also be cautioned to take note that high-power radars are allocated as primary users (meaning they have priority) of the bands 5250-5350 MHz and 5650-5850 MHz and these radars could cause interference and/or damage to LE-LAN devices.IC Radiation Exposure Statement:This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.Viewing Certifications1Go to http://www.zyxel.com.2Select your product on the ZyXEL home page to go to that product's page.3Select the certification you wish to view from this page.ZyXEL Limited WarrantyZyXEL warrants to the original end user (purchaser) that this product is free from any defects in material or workmanship for a specific period (the Warranty Period) from the date of purchase. The Warranty Period varies by region. Check with your vendor and/or the authorized ZyXEL local distributor for details about the Warranty Period of this product. During the warranty period, and upon proof of purchase, should the product have indications of failure due to faulty workmanship and/or materials, ZyXEL will, at its discretion, repair or replace the defective products or components without charge for either parts or labor, and to whatever extent it shall deem necessary to restore the product or components to proper operating condition. Any replacement will consist of a new or re-manufactured functionally equivalent product of equal or higher value,
Appendix G Legal InformationWAP5605 User’s Guide222and will be solely at the discretion of ZyXEL. This warranty shall not apply if the product has been modified, misused, tampered with, damaged by an act of God, or subjected to abnormal working conditions.NoteRepair or replacement, as provided under this warranty, is the exclusive remedy of the purchaser. This warranty is in lieu of all other warranties, express or implied, including any implied warranty of merchantability or fitness for a particular use or purpose. ZyXEL shall in no event be held liable for indirect or consequential damages of any kind to the purchaser.To obtain the services of this warranty, contact your vendor. You may also refer to the warranty policy for the region in which you bought the device at http://www.zyxel.com/web/support_warranty_info.php.RegistrationRegister your product online to receive e-mail notices of firmware upgrades and information at www.zyxel.com.Regulatory InformationEuropean UnionThe following information applies if you use the product within the European Union. Declaration of Conformity with Regard to EU Directive 1999/5/EC (R&TTE Directive)Compliance Information for 5GHz Wireless Products Relevant to the EU and Other Countries Following the EU Directive 1999/5/EC (R&TTE Directive) [Czech] ZyXEL tímto prohlašuje, že tento zařízení je ve shodě se základními požadavky a dalšími příslušnými ustanoveními směrnice 1999/5/EC.[Danish] Undertegnede ZyXEL erklærer herved, at følgende udstyr udstyr overholder de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF.[German] Hiermit erklärt ZyXEL, dass sich das Gerät Ausstattung in Übereinstimmung mit den grundlegenden Anforderungen und den übrigen einschlägigen Bestimmungen der Richtlinie 1999/5/EU befindet.[Estonian] Käesolevaga kinnitab ZyXEL seadme seadmed vastavust direktiivi 1999/5/EÜ põhinõuetele ja nimetatud direktiivist tulenevatele teistele asjakohastele sätetele.English Hereby, ZyXEL declares that this equipment is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.[Spanish] Por medio de la presente ZyXEL declara que el equipo cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE.[Greek] ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ ZyXEL ΔΗΛΩΝΕΙ ΟΤΙ εξοπλισμός ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩΔΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ ΤΗΣ ΟΔΗΓΙΑΣ 1999/5/ΕC.[French] Par la présente ZyXEL déclare que l'appareil équipements est conforme aux exigences essentielles et aux autres dispositions pertinentes de la directive 1999/5/EC.
Appendix G Legal InformationWAP5605 User’s Guide 223National RestrictionsThis product may be used in all EU countries (and other countries following the EU directive 1999/5/EC) without any limitation except for the countries mentioned below:Ce produit peut être utilisé dans tous les pays de l’UE (et dans tous les pays ayant transposés la directive 1999/5/CE) sans aucune limitation, excepté pour les pays mentionnés ci-dessous:Questo prodotto è utilizzabile in tutte i paesi EU (ed in tutti gli altri paesi che seguono le direttive EU 1999/5/EC) senza nessuna limitazione, eccetto per i paesii menzionati di seguito:Das Produkt kann in allen EU Staaten ohne Einschränkungen eingesetzt werden (sowie in anderen Staaten die der EU Direktive 1995/5/CE folgen) mit Außnahme der folgenden aufgeführten Staaten:[Italian] Con la presente ZyXEL dichiara che questo attrezzatura è conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE.[Latvian] Ar šo ZyXEL deklarē, ka iekārtas atbilst Direktīvas 1999/5/EK būtiskajām prasībām un citiem ar to saistītajiem noteikumiem.[Lithuanian] Šiuo ZyXEL deklaruoja, kad šis įranga atitinka esminius reikalavimus ir kitas 1999/5/EB Direktyvos nuostatas.[Dutch] Hierbij verklaart ZyXEL dat het toestel uitrusting in overeenstemming is met de essentiële eisen en de andere relevante bepalingen van richtlijn 1999/5/EC.[Maltese] Hawnhekk, ZyXEL, jiddikjara li dan tagħmir jikkonforma mal-ħtiġijiet essenzjali u ma provvedimenti oħrajn relevanti li hemm fid-Dirrettiva 1999/5/EC.[Hungarian] Alulírott, ZyXEL nyilatkozom, hogy a berendezés megfelel a vonatkozó alapvetõ követelményeknek és az 1999/5/EK irányelv egyéb elõírásainak.[Polish] Niniejszym ZyXEL oświadcza, że sprzęt jest zgodny z zasadniczymi wymogami oraz pozostałymi stosownymi postanowieniami Dyrektywy 1999/5/EC.[Portuguese] ZyXEL declara que este equipamento está conforme com os requisitos essenciais e outras disposições da Directiva 1999/5/EC.[Slovenian] ZyXEL izjavlja, da je ta oprema v skladu z bistvenimi zahtevami in ostalimi relevantnimi določili direktive 1999/5/EC.[Slovak] ZyXEL týmto vyhlasuje, že zariadenia spĺňa základné požiadavky a všetky príslušné ustanovenia Smernice 1999/5/EC.[Finnish] ZyXEL vakuuttaa täten että laitteet tyyppinen laite on direktiivin 1999/5/EY oleellisten vaatimusten ja sitä koskevien direktiivin muiden ehtojen mukainen.[Swedish] Härmed intygar ZyXEL att denna utrustning står I överensstämmelse med de väsentliga egenskapskrav och övriga relevanta bestämmelser som framgår av direktiv 1999/5/EC.[Bulgarian] С настоящото ZyXEL декларира, че това оборудване е в съответствие със съществените изисквания и другите приложими разпоредбите на Директива 1999/5/ЕC.[Icelandic] Hér með lýsir, ZyXEL því yfir að þessi búnaður er í samræmi við grunnkröfur og önnur viðeigandi ákvæði tilskipunar 1999/5/EC.[Norwegian] Erklærer herved ZyXEL at dette utstyret er I samsvar med de grunnleggende kravene og andre relevante bestemmelser I direktiv 1999/5/EF.[Romanian] Prin prezenta, ZyXEL declară că acest echipament este în conformitate cu cerinţele esenţiale şi alte prevederi relevante ale Directivei 1999/5/EC.
Appendix G Legal InformationWAP5605 User’s Guide224In the majority of the EU and other European countries, the 5-GHz bands have been made available for the use of wireless local area networks (LANs). Later in this document you will find an overview of countries inwhich additional restrictions or requirements or both are applicable.The requirements for any country may evolve. ZyXEL recommends that you check with the local authorities for the latest status of their national regulations for both the 5-GHz wireless LANs.The following countries have restrictions and/or requirements in addition to those given in the table labeled “Overview of Regulatory Requirements for Wireless LANs”:.BelgiumThe Belgian Institute for Postal Services and Telecommunications (BIPT) must be notified of any outdoor wireless link having a range exceeding 300 meters. Please check http://www.bipt.be for more details.Draadloze verbindingen voor buitengebruik en met een reikwijdte van meer dan 300 meter dienen aangemeld te worden bij het Belgisch Instituut voor postdiensten en telecommunicatie (BIPT). Zie http://www.bipt.be voor meer gegevens.Les liaisons sans fil pour une utilisation en extérieur d’une distance supérieure à 300 mètres doivent être notifiées à l’Institut Belge des services Postaux et des Télécommunications (IBPT). Visitez http://www.ibpt.be pour de plus amples détails.DenmarkIn Denmark, the band 5150 - 5350 MHz is also allowed for outdoor usage.I Danmark må frekvensbåndet 5150 - 5350 også anvendes udendørs.ItalyThis product meets the National Radio Interface and the requirements specified in the National Frequency Allocation Table for Italy. Unless this wireless LAN product is operating within the boundaries of the owner's property, its use requires a “general authorization.” Please check http://www.sviluppoeconomico.gov.it/ for more details.Questo prodotto è conforme alla specifiche di Interfaccia Radio Nazionali e rispetta il Piano Nazionale di ripartizione delle frequenze in Italia. Se non viene installato all 'interno del proprio fondo, l'utilizzo di prodotti Wireless LAN richiede una “Autorizzazione Generale”. Consultare http://www.sviluppoeconomico.gov.it/ per maggiori dettagli.Notes:1. Although Norway, Switzerland and Liechtenstein are not EU member states, the EU Directive 1999/5/EC has also been implemented in those countries.Overview of Regulatory Requirements for Wireless LANs Frequency Band (MHz) Max Power Level (EIRP)1 (mW) Indoor ONLY Indoor and Outdoor 5150-5350 200 V 5470-5725 1000 V
Appendix G Legal InformationWAP5605 User’s Guide 2252. The regulatory limits for maximum output power are specified in EIRP. The EIRP level (in dBm) of a device can be calculated by adding the gain of the antenna used(specified in dBi) to the output power available at the connector (specified in dBm).
Appendix G Legal InformationWAP5605 User’s Guide226
IndexWAP5605 User’s Guide 227IndexAAdvanced Encryption StandardSee AES.AES 171alternative subnet mask notation 127antennadirectional 175gain 175omni-directional 175AP 15AP (access point) 165AP Modemenu 35status screen 33, 39AP+Bridge 15BBasic Service Set, See BSS 163Bridge/Repeater 15BSS 163CCA 170Certificate AuthoritySee CA.certifications 219notices 220viewing 221Channel 34channel 76, 165interference 165Configurationrestore 99copyright 219CPU usage 35, 40CTS (Clear to Send) 166DDaylight saving 96Dimensions 107disclaimer 219dynamic WEP key exchange 170EEAP Authentication 169encryption 77, 171key 77WPA compatible 77ESS 164Extended Service Set, See ESS 164FFCC interference statement 219Firmware upload 96file extensionusing HTTPfirmware version 34, 39fragmentation threshold 166GGeneral wireless LAN screen 78Hhidden node 165
IndexWAP5605 User’s Guide228IIANA 132IBSS 163IEEE 802.11g 167Independent Basic Service SetSee IBSS 163initialization vector (IV) 172Internet Assigned Numbers AuthoritySee IANA 132IP Address 92IP alias 90LLAN 89LAN overview 89LAN setup 89LAN TCP/IP 90Language 99Link type 34, 40Local Area Network 89Log 71logssettings 72MMAC 82MAC address 76MAC address filter 76MAC address filtering 82MAC filter 82managing the devicegood habits 16using the web configurator. See web configurator.using the WPS. See WPS.MBSSID 15Media access control 82Memory usage 35, 40Message Integrity Check (MIC) 171mode 15NNAT 132Navigation Panel 35navigation panel 35OOperating Channel 34operating mode 15PPairwise Master Key (PMK) 172, 173port speed 34, 40Power Specification 107preamble mode 167product registration 222PSK 172QQuality of Service (QoS) 84RRADIUS 168message types 169messages 169shared secret key 169registrationproduct 222related documentation 3Reset button 17Reset the device 17Restore configuration 99RF (Radio Frequency) 108RTS (Request To Send) 166threshold 165, 166
IndexWAP5605 User’s Guide 229RTS/CTS Threshold 76, 83Ssafety warnings 6Scheduling 87Service Set 28, 78Service Set IDentification 28, 78Service Set IDentity. See SSID.SSID 28, 34, 40, 76, 78subnet 125Subnet Mask 92subnet mask 126subnetting 128SummaryPacket statistics 73Wireless station status 74syntax conventions 4System General Setup 93System restart 99TTemperature 107Temporal Key Integrity Protocol (TKIP) 171Time setting 95Wwarranty 221note 222Web Configuratorhow to access 49Overview 49web configurator 16WEP Encryption 44, 45, 80, 81WEP encryption 80WEP key 80Wi-Fi Protected Access 171Wireless association list 74wireless client WPA supplicants 172wireless LAN scheduling 87Wireless networkbasic guidelines 75channel 76encryption 77example 75MAC address filter 76overview 75security 76SSID 76Wireless security 76overview 76type 76wireless security 167Wireless tutorial 55WPS 55WLANinterference 165security parameters 174WLAN button 17WPA 171key caching 172pre-authentication 172user authentication 172vs WPA-PSK 172wireless client supplicant 172with RADIUS application example 173WPA compatible 77WPA2 171user authentication 172vs WPA2-PSK 172wireless client supplicant 172with RADIUS application example 173WPA2-Pre-Shared Key 171WPA2-PSK 171, 172application example 173WPA-PSK 171, 172application example 173WPS 16
IndexWAP5605 User’s Guide230

Navigation menu