Benefon E TDM 20 N Owner’s Manual Forte Sm En
User Manual: benefon TDM 20 N - Owner’s Manual Free User Guide for Benefon Mobile Phone, Manual
Open the PDF directly: View PDF 
.
Page Count: 134
| Download | |
| Open PDF In Browser | View PDF |
Product: TDM-20-N (Forte i) / 28.1.1999 TDM-20-N 1.0 GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 1 1.0.1 Benefon Forte and Data Interface . . . . . . . . . . . . . . . . . . . . . . . 1 - 1 1.0.2 Benefon Forte and Fax . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 2 1.0.3 Benefon Forte and PC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 3 2.0 INSTALLATION INSTRUCTIONS . . . . . . . . . . . . . . . 2 - 1 2.0.1 Techninal Data of Benefon Forte . . . . . . . . . . . . . . . . . . . . . . . . 2 - 3 2.0.2 Car Installation kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - 3 2.0.3 Transceiver Unit Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - 3 2.0.4 Handset Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - 5 2.0.5 Speaker Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - 6 2.0.6 Microphone Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - 6 2.0.7 Voice-Controlled HF Installation . . . . . . . . . . . . . . . . . . . . . . . . . 2 - 7 2.0.8 Mounting the Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - 7 2.0.9 Antenna Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - 9 2.0.10 Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - 10 2.0.11 Identity Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - 11 2.0.12 Combination Lock Programming . . . . . . . . . . . . . . . . . . . . . . 2 - 11 2.0.13 Test Local Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - 12 3.0 OWNER’S MANUAL . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 1 4.0 LOCAL SERVICE COMMANDS . . . . . . . . . . . . . . . . . 4 - 1 4.0.1 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 - 1 4.0.2 Special Push Buttons In Local . . . . . . . . . . . . . . . . . . . . . . . . . . 4 - 1 4.0.3 General Form Of Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 - 1 4.0.4 Local Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 - 2 4.0.5 Guide Texts And Error Situations . . . . . . . . . . . . . . . . . . . . . . . 4 - 11 4.0.6 Local-Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 - 12 5.0 TUNING INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . 5 - 1 5.0.1 Connect To Phone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 1 5.0.2 Synthesizer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 1 5.0.3 RX-VCO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 1 Tdm20enTOC.fm 1 Product: TDM-20-N (Forte i) / 28.1.1999 5.0.4 TX-VCO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 1 5.0.5 Channel Frequency Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 2 5.0.6 Transmitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 2 5.0.7 TX-Audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 2 5.0.8 Max DEV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 3 5.0.9 FFSKT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 3 5.0.10 RX-Audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 3 5.0.11 RX-Response . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 3 5.0.12 RX-Distortion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 3 5.0.13 TX-Distortion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 4 5.0.14 FII DEV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 4 5.0.15 Tuning The RSSI-Levels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 4 5.0.16 Tuning FSK-split level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 5 5.0.17 Program Base-Band (if neccessery) . . . . . . . . . . . . . . . . . . . . 5 - 5 5.0.18 Programming The Subscriber Number . . . . . . . . . . . . . . . . . . 5 - 5 6.0 TRANSMITTER MODULE OT0001 SPECIFICATIONS: 6 - 1 6.0.1 Connector Description: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 - 1 6.0.2 Tuning Instructions: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 - 1 6.0.3 Test Point Voltages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 - 2 6.0.4 Parts list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 - 4 7.0 RECEIVER MODULE OR0002 SPECIFICATIONS . . 7 - 1 7.0.1 Principles Of Receiver Operation . . . . . . . . . . . . . . . . . . . . . . . . 7 - 1 7.1 Receiver OR0002 settings . . . . . . . . . . . . . . . . . . . . . . 7 - 2 7.1.1 Supply Voltages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 - 2 7.1.2 Setting Order: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 - 2 7.1.3 Check Sensitivities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 - 3 7.1.4 Parts list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 - 4 8.0 SYNTHESIZER MODULE OS0021 SPECIFICATIONS 8 - 1 8.0.1 Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 - 1 8.0.2 Circuit Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 - 1 8.0.3 RX-Synthesizer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 - 1 8.0.4 TX-Synthesizer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 - 2 8.1 Synthesizer OS0021 Settings . . . . . . . . . . . . . . . . . . . 8 - 3 Tdm20enTOC.fm 2 Product: TDM-20-N (Forte i) / 28.1.1999 8.1.1 Checking Operating Voltages . . . . . . . . . . . . . . . . . . . . . . . . . . 8 - 3 8.1.2 RX-VCO Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 - 3 8.1.3 TX-VCO Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 - 3 8.1.4 Setting Channel Frequency: . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 - 4 8.1.5 Adjusting The Modulation: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 - 4 8.1.6 Correcting The Low-frequency Response: . . . . . . . . . . . . . . . . . 8 - 4 8.1.7 Parts list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 - 5 9.0 POWER SUPPLY MODULE OW0002 SPECIFICATIONS 9 - 1 9.0.1 Connector X800 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 - 1 9.0.2 Connector X820 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 - 1 9.0.3 Connector X830 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 - 1 9.0.4 Operation Principles: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 - 1 9.0.5 Parts list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 - 2 10.0 AUDIO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 - 1 10.0.1 Principles Of Audio Operation . . . . . . . . . . . . . . . . . . . . . . . . 10 - 1 10.0.2 TX-Audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 - 1 10.0.3 RX-Audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 - 1 10.0.4 Regulator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 - 2 10.0.5 Audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 - 2 10.0.6 Audio Input Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 - 3 10.0.7 Audio Output Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 - 3 10.0.8 Audio Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 - 4 10.0.9 Operating Voltages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 - 4 10.0.10 RX Audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 - 4 10.0.11 TX-Audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 - 5 10.0.12 Maximum Deviation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 - 5 10.0.13 FFSKT Deviation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 - 6 10.0.14 FII Deviation, Method 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 - 6 10.0.15 FII Deviation, Method 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 - 6 10.0.16 Limiter Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 - 7 10.0.17 Deviation Limiter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 - 7 10.0.18 Voice Operated HF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 - 7 10.1 Processor Functions . . . . . . . . . . . . . . . . . . . . . . . . 10 - 8 10.1.1 The Processor Includes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 - 8 Tdm20enTOC.fm 3 Product: TDM-20-N (Forte i) / 28.1.1999 10.1.2 Connectors: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 - 9 10.1.3 Circuit Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 - 11 10.1.4 Parts list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 - 16 11.0 PRINCIPLES OF HANDSET OPERATION . . . . . . 11 - 1 11.0.1 Connector Signals: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 - 1 11.0.2 Audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 - 1 11.0.3 Automatic Control For Keyboard And Lcd Backlight . . . . . . . 11 - 1 11.0.4 Leds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 - 1 11.0.5 Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 - 2 12.0 DATA-INTERFACE FUNCTION OUTLINE . . . . . . . 12 - 1 12.0.1 The Processor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 - 1 12.0.2 Memory Addresses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 - 1 12.0.3 Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 - 1 12.0.4 Processor I/O Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 - 2 12.0.5 Audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 - 3 12.0.6 Ring- And Line-voltage Power Supply . . . . . . . . . . . . . . . . . . 12 - 3 12.0.7 Parts list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 - 5 13.0 INSTALLATION OF ANSWERING MACHINE . . . . 13 - 1 13.1 Answering Machine . . . . . . . . . . . . . . . . . . . . . . . . . 13 - 2 13.1.1 Processor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 - 2 13.1.2 Memory Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 - 2 13.1.3 Watchdog . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 - 2 13.1.4 Audio Paths . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 - 2 13.1.5 ICC-Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 - 3 13.1.6 Operating Voltages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 - 3 13.1.7 Parts list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 - 4 Tdm20enTOC.fm 4 Product: TDM-20-N (Forte i) / 28.1.1999 1.0 GENERAL 1.0.1 Benefon Forte and Data Interface Outdoor antenna BENEF Forte with optional answering machine N Microphone is plugged to the jack, which is in the handset's connector Microphone Telefax Home telephone Modem ja PC PABX Data interface Loudspeaker Car radio mute External alarm + Car battery (+12 VDC) GND IGS TDM-10E2_fm5.fm 1 Product: TDM-20-N (Forte i) / 28.1.1999 1.0.2 Benefon Forte and Fax +12 V GND IGS AL MUTE TDM-10E2_fm5.fm 2 Product: TDM-20-N (Forte i) / 28.1.1999 1.0.3 Benefon Forte and PC +12 V GND IGS AL MUTE TDM-10E2_fm5.fm 3 Product: TDM-20-N / Installation Instructions 28.1.1999 2.0 INSTALLATION INSTRUCTIONS Installation Instructions PROLOGUE These installation instructions have been prepared to assist fitters in installing the equipment, and are as such only to serve as a guide. Nothing beats common sense and good experience. Installation is always based on the need of the customer to use the phone in the environment in which it will be installed. Negotiate with the customer where the different parts will be installed. It is important that the customer tells of his own preferences and choices, and that the fitter/salesman tells where it is possible/advisable to locate different items. It is the salesman’s responsibility to see that the installation order is properly filled out. RECOMMEND - antenna location on the roof - handset location does not interfere with road safety - speaker located in the driver’s side leg-room - microphone as close as possible to the driver’s mouth - car radio muting ASK IF THE USER WANTS - automatic start-up - additional alarm - car radio muting Benefon Oy TDM-10E6_fm5.fm 1 Product: TDM-20-N / Installation Instructions 28.1.1999 CONTENTS 1.0.1 Techninal Data of Benefon Forte . . . . . . . . . . . . . . . . . . . . . . . . . . .3 1.0.2 Car Installation kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 1.0.3 Transceiver Unit Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 1.0.3.1 Positioning the Mounting Bracket . . . . . . . . . . . . . . . . . . . . . . .4 1.0.3.2 Locking the Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 1.0.4 Handset Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 1.0.4.1 Holder Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 1.0.4.2 Mounting the Handset Holder-Base . . . . . . . . . . . . . . . . . . . . .5 1.0.4.3 Removal of the holder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 1.0.5 Speaker Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 1.0.6 Microphone Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 1.0.7 Voice-Controlled HF Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 1.0.7.1 HF Tuning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 1.0.8 Mounting the Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 1.0.8.1 Power Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 1.0.8.2 System Connector (Same Pinning in the System Cable) . . . . .8 1.0.9 Antenna Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 1.0.9.1 On Car Roof . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 1.0.9.2 On Car Wing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 1.0.9.3 On Boot Lid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 1.0.9.4 On Vehicle Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 1.0.10 Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 1.0.10.1 Power timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10 1.0.10.2 Car Radio Muting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10 1.0.10.3 Additional Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11 1.0.11 Identity Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 1.0.11.1 Subscriber Number Programming . . . . . . . . . . . . . . . . . . . .11 1.0.12 Combination Lock Programming . . . . . . . . . . . . . . . . . . . . . . . . .11 1.0.12.1 Sales Date Programming . . . . . . . . . . . . . . . . . . . . . . . . . . .12 1.0.13 Test Local Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 TDM-10E6_fm5.fm 2 Product: TDM-20-N / Installation Instructions 28.1.1999 2.0.1 Techninal Data of Benefon Forte Operating Voltage Current consumption Interfaces 13.8 VDC 0.25 A stby Current-timer IGS - Car radio muting MUTE Additional alarm AL HF-microphone DTMF-transmitter DTMF-receiver built-in built-in built-in (requires separate microphone) 99 + 2 memory places ( 0 RCL last-repeat dialling ) 00 RCL memory search during phonecall ( 01-99 RCL shortcode memories ) Voice-controlled HF Memories (tel.number) 4.5A TXon Alarm signals settings for frequenct, level (either increasing or fixed), cycle and tone (menu). 2.0.2 Car Installation kit Number 1 2 3 4 5 Description MUTE IGS GND AL SPKR 2.0.3 Transceiver Unit Installation The mounting bracket can be installed in e.g. trunk. TDM-10E6_fm5.fm 3 Product: TDM-20-N / Installation Instructions 28.1.1999 2.0.3.1 Positioning the Mounting Bracket Should the telephone be requied also for indoor use, or in another vehicle, it is recommended to install the transceiver unit in an easily accessible place. 2.0.3.2 Locking the Connector The antenna, system cable, and combined power/accessiry connector are fixed. TDM-10E6_fm5.fm 4 Product: TDM-20-N / Installation Instructions 28.1.1999 2.0.4 Handset Installation The handset should be mounted to allow easy use and ensure safe operation BENEF N 2.0.4.1 Holder Installation 2.0.4.2 Mounting the Handset Holder-Base Screw the handset holder-base in place, and snap the holder into position by twisting it carefully clockwise. TDM-10E6_fm5.fm 5 Product: TDM-20-N / Installation Instructions 28.1.1999 2.0.4.3 Removal of the holder The holder can be removed by carefully pressing the locking-tab (back, left) and carefully turning the holder counter-clockwise. 2.0.5 Speaker Installation For Hands Free operation, the best place to mount the speaker is on the dirver’s side of the dashboard, pointing directly towards the driver. The speaker is connected with the connecting cable. 2.0.6 Microphone Installation The following points should be noted when installing the microphone: - the microphone must not be directed at the speaker - it is not recommended to mount the microphone on a sun-blind, because the microphone direction will change with movement of the sun-blind - the microphone must not be in the driver’s line of vision, where it could be distracting TDM-10E6_fm5.fm 6 Product: TDM-20-N / Installation Instructions 28.1.1999 - maximum range from driver’s mouth - about 20 cm - the microphone is connected to the handset with a jack-plug - it is not recommended to mount the speaker on a door-pillar or similar location due to the high background noise at the side of vehicle 2.0.7 Voice-Controlled HF Installation To ensure trouble-free HF operation, be sure to mount the speaker and microphone carefully, as descriped on the previous page. 2.0.7.1 HF Tuning With installation complete, connect loccal-box to both the handset spiral cable and the handset system cable, and set telephone to local mode; press 1# and start the vehicle; check the reading on the display for different revs, and press OK twice when it is at its greatest. Best results are obtained when HF tuning can be accomplished with the vehicle moving at normal speeds. Default value on display is 34, and the final value is 34 + compensation value. In practice 40...55, depending on the vehicle. 2.0.8 Mounting the Cables There are two cables coming from the radio module: power and system cable. The red supply cable connected to the battery. With a 24 V supply, a voltage regulator must be used. The black ground cable should be connected to a sufficiently firm place near the radio module. TDM-10E6_fm5.fm 7 Product: TDM-20-N / Installation Instructions 28.1.1999 2.0.8.1 Power Connector Includes SPKR, GND, IGS, AL and MUTE connections. Number 1 2 3 4 5 6 Description MUTE IGS GND AL SPKR +12v 2.0.8.2 System Connector (Same Pinning in the System Cable) Number 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 TDM-10E6_fm5.fm Description GND MIC AGND AUTOCALL TXDX 12CINT SDAX +9 ERP PTT RXDX SCLK 8 Product: TDM-20-N / Installation Instructions 28.1.1999 2.0.9 Antenna Installation 2.0.9.1 On Car Roof The most recommended antenna location is on the car roof. + highest location + circular radiation trace + no shadows + good grounding 2.0.9.2 On Car Wing + easy to mount - irregular grounding - car body creates shadows 2.0.9.3 On Boot Lid Not recommended under any circumstances - causes constant duplex-interference 2.0.9.4 On Vehicle Window + no holes in the bodywork - does not work as well as body mounting - expensive TDM-10E6_fm5.fm 9 Product: TDM-20-N / Installation Instructions 28.1.1999 2.0.10 Connections 2.0.10.1 Power timer IGS power timer is connected to the vehicle electrical system so that power on is VB and power off is OV, figure 1. 1 2 3 MUTE IGS GND 4 AL 5 6 SPKR +VB Caution! The same numbering is used with the power cable NOTE! IGS connection must not be made to the ignition system. 2.0.10.2 Car Radio Muting MUTE car radio muting is connected with a connecting cable to the relay pins. RELAY 86 8 7A 30 85 RELAY +ACC Car radio supply voltage 30 87A V B A TT Voltage from car battey 85 86 car radio MUTE (EXTVB connector pin 1 in carbox) TDM-10E6_fm5.fm 10 Product: TDM-20-N / Installation Instructions 28.1.1999 2.0.10.3 Additional Alarm AL alarm system is connected with a 4-ply connector to either a relay or an extension. Alarm on/off is set by the handset menu. RELAY 86 87A 30 85 RELAY 30 V B A TT 87 HORN 85 86 AL (EXTVB connector pin 4 in carbox) 2.0.11 Identity Programming Connect a local-box with programming rights between the handset and the radio module; turn power on, and press 0#, and LOCAL will be shown on the display. 2.0.11.1 Subscriber Number Programming Press 2#, and Z X1 X2 X3 X4 X5 X6 Y1 Y2 Y3, and finally OK Z = country code X1...X6 = 6-digit subscriber number Y1... Y3 = 3.digit password Check: Press 2*, in case of error, and start subscriber-number programming again. 2.0.12 Combination Lock Programming Press 3#, and X1 X2 X3 X4, and finally OK X1...X4 = customer-defined combination Check: Press 3*, in case of error, and start combination lock programming again. TDM-10E6_fm5.fm 11 Product: TDM-20-N / Installation Instructions 28.1.1999 2.0.12.1 Sales Date Programming Press 4#, and XX XX XX, and finally OK XX XX XX = d mm yy, for example 08 0 Check: Press 4*, in case of error, and start sales date programming again. 2.0.13 Test Local Commands Command Function 0# 1# 2# 2* 3# 3* 4# 4* Transfer to LOCAL mode HF tuning OK adjustment OK end Subscriber number programming, and OK Check subscriber number Combination lock programming (4 digits) and OK Check combination lock Sales date programming (6 digits) and OK Check sales date Change call country. Call country on the display enter new call coun with +/- buttons, store with OK Additional Alarm on Additional alarm OFF Car radio mute ON Car radio mute OFF Reads IGN, HOOK, PTT, and AUTOCALL lines Transfer shortcodes to LOCAL-BOX Transfer shortcodes back to radio module 5# 6# 6* 7# 7* 8# 9# 999* TDM-10E6_fm5.fm 12 3.0 OWNER’S MANUAL 1user_gb.fm 1 Product: TDM-20-N / 28.1.1999 4.0 LOCAL SERVICE COMMANDS 4.0.1 General There is a special program module called LOCAL which makes it possible to set, read and program various features of the phone. In order to activate the LOCAL program it is necessary to connect a local box between the radio unit and the handset. When the power is switched on, and the local box is connected, the LOCAL program becomes activated. There are two kinds of local boxes. One merely has "service rights", i.e. you cannot program subscriber number. The other has "full rights", i.e. there are no restrictions in LOCAL. 4.0.2 Special Push Buttons In Local Button Action R HF Changes between LOCAL and NMT program Changes between earphone and speaker -HF-led indicates speaker modeEnds local command influence Used for scrolling letters A, b, C, D, E, F (accepts either with OK or digit button) Volume settings SND/END MFT +/- 4.0.3 General Form Of Commands X(XX)# X(XX)* XXXX# XXXX* DO UNDO corresponding X(XX)# command Channel command BURN-IN channel (default = 45) Note: In LOCAL mode * = b and # = C TDM-10E3_fm5.fm 1 Product: TDM-20-N / 28.1.1999 4.0.4 Local Commands 4.0.4.1 INSTALL AND PURCHASE X TDM-10E3_fm5.fm 0# Reset LOCAL 1# Tune HF microphone threshold - Background noise level appears on display. Push OK to add registered level to default (set level can be corrected with digit buttons). - store with OK 2# Program subscriber number ( needs local box with "full rights") - push Z X1 X2 X3 X4 X5 X6 Y1 Y2 Y3 (ten digits) Z = Country code X1...X6 = subscriber number Y1...Y3 = password - store with OK 2* Read subscriber number 3# Program lock code - push four digits - store with OK 3* Read lock code 4# Program purchase date - push six digits (ddmmyy) - store with OK 4* Read purchase date 5# Change countrycode - give new country (5...8) or select with +/- button - store with OK 6# External alert ON 6* External alert OFF 2 Product: TDM-20-N / 28.1.1999 7# Car radio mute ON 7* Car radio mute OFF 8# Read IGN / HOOK / PTT / AUTOCALL in realtime 9# Move shortcode memory from the phone to the local box 999* Move shortcode memory from the local box to the phone 4.0.4.2 Read And Write Port 0X 00# Write to port - push (portnumber) (bitnumber) (bitstate) portnumber: bitnumber: bitstate: 01# Read port in realtime - push (portnumber) portnumber: 02# 0 processor-module input-latch 1 IICINT / PTT / HOOK Read A/D-channel in realtime - push (channelnumber) channelnumber: TDM-10E3_fm5.fm 0 1. latch in processor-module 1 2. latch in processor-module 2 3. latch in processor-module 3 4. latch in processor-module 4 handset "button port" 5 handset "led port" A6 processor PA D processor PD 0...7 0 or 1 0 1 2 3 4 5 6 7 RSSI TXSENSE MICDET ERPDET HOOK PTT POTIND not in use 3 Product: TDM-20-N / 28.1.1999 4.0.4.3 Processor Tests 1X TDM-10E3_fm5.fm 10# Test memory - EPROM fail XX1, no fail XX0 - EEPROM fail X2X, no fail X0X - RAM fail 3XX, no fail 0XX 11# Test COP (= watchdog) - Resets phone if COP is in order, otherwise stops 12# Send "0"-frequency - Doesn‘ t set transmitter 12* End send 13# Send of "1"-frequency - Doesn‘ t set transmitter 13* End send 14# Send frame - frame is given by push button set (16 digits and #) N1 N2 N3 P(X) Y1 Y2 Z X1 X2 X3 X4 X5 X6 J1 J2 J3 # - default frame is 15 - letters A...F are given with MFT-button 14* End send 15# Receive frame 16# Detect FSK in realtime 17# Receive DTMF 18# DTMF loop test 4 Product: TDM-20-N / 28.1.1999 4.0.4.4 Audio Tests 2X TDM-10E3_fm5.fm 20# AUDIOPWR = 1 20* AUDIOPWR = 0 200# Compander ON 200* Compander OFF 21# TX-audio ON -AUDIOPWR = TXAON = 1 - MICVOL = 111 - microphone = MIC if ERPON, EXTMIC if SPKON 21* TX-audio OFF - TXAON = 0 - microphone OFF 22# RX-audio ON - AUDIOPWR = RXAON = ERPON = 1 - AUDIOLOOP = SPKON = 0 - ERPVOL = 011 22* RX-audio OFF - RXAON = 0 23# Fiiloop ON - AUDIOPWR = FIILOOP = 1 23* Fiiloop OFF - FIILOOP = 0 24# FFSKT ON - AUDIOPWR = FFSKT = 1 24* FFSKT OFF - FFSKT = 0 25# Audio-tone generator ON - AUDIOPWR = DTMFON = 1 - DTMF generator output = 980 Hz 25* Audio-tone generator OFF - DTMFON = 0 5 Product: TDM-20-N / 28.1.1999 - DTMF generator output = OFF TDM-10E3_fm5.fm 26# Auxiliary pass ON - AUDIOPWR = AUXOFF = 1 26* Auxiliary pass OFF - AUXOFF = 0 27# Audioloop ON - AUDIOPWR = AUDIOLOOP = 1 27* Audioloop OFF - AUDIOLOOP = 0 28# Microphone volume settings +/- 28* Earphone/speaker volume settings +/- 29# Handset microphone ON 29* Microphone OFF 6 Product: TDM-20-N / 28.1.1999 4.0.4.5 Transmitter And Receiver Tests 3X, 4X TDM-10E3_fm5.fm 30# Transmitter ON in previous txpower 30* Transmitter OFF 31# Transmitter ON in low txpower 31* Transmitter OFF 32# Transmitter ON in medium txpower 32* Transmitter OFF 33# Transmitter ON in high txpower 33* Transmitter OFF 34# TXVCO ON 34* TXVCO OFF 35# First channel 36# Middle channel 37# Last channel 38# Tune and program RSSI levels - Display shows level to tune (in dBm‘ s) PG-53, PG-63, PG-93, PG-103, PG-115 - Push OK to tune next level - Push OK to store after tuning -115 dBm - (If you want store values before tuning -115 dBm push RCL) - Store is done if tuned values are -53 dBm > = -63 dBm > = -115 dBm 38* Read programmed RSSI-levels 39# Tune and program deviation limit levels - Display shows level to tune DEV LO, DEV HI - Push OK to tune next level - Push OK to store after tuning DEV HI - (If you want store DEV LO before tuning DEV HI push RCL) - Store is done if tuned values are DEV HI > = DEV LO 7 Product: TDM-20-N / 28.1.1999 39* Read programmed audiolimiter levels 40# RX path measurement in middle channel - AUDIOPWR = RXAON = ERPON = AUXOFF = 1 - TXON = TXVCO = AUDIOLOOP = FIILOOP = SPKON = 0 - ERPVOL = 111 41# TX path measurement in middle channel high txpower - AUDIOPWR = TXVCO = TXAON = 1 - FFSKT = DTMFON = AUDIOLOOP = FIILOOP = 0 - ERPVOL = 111 42# RX path measurement in middle channel high txpower - AUDIOPWR = TXVCO = FIILOOP = RXAON = ERPON = AUXOFF= TXAON = 1 - AUDIOLOOP = SPKON = FFSKT = DTMFON = 0 - MICVOL = 111, ERPVOL = 011 43# Channel scan - starts from current channel 44# Step channels with +/- button 4.0.4.6 Handset And Accessory Tests 5X 50# Display, leds and illumination ON 50* Display, leds and illumination OFF 51# Answering-machine loop test 4.0.4.7 Read Information 6X 60# Read power off counters 0 1 2 3 4 5 TDM-10E3_fm5.fm RAM fail EPROM fail EEPROM fail COP fail (not used) No RSSI in conversation Transmitter ON during scan 8 Product: TDM-20-N / 28.1.1999 6 7 TDM-10E3_fm5.fm No Handset FSK detected in conversation 60* Reset all power off counters 61# Read sellercode 62# Read program version (ddmmyy) 70# 70* Tune FSK split level - store with OK key Read FSK split level 71# Base-band programming 71* Read Base-band 9 Product: TDM-20-N / 28.1.1999 4.0.4.8 Clearing Of Memory 8X 80# Clear RAM 81# Clear EEPROM - not the tuned values 810# Clear whole EEPROM 82# Clear RAM and EEPROM -not the tuned values 4.0.4.9 Burn-in 9X 98# Start BURN-IN if enabled 98* Stop BURN-IN if IGN not connected 99# Enable BURN-IN 99* Disable BURN-IN 100# SIM using normal SAK number - defaul value always when phone is ON SIM using test SAK number 100* TDM-10E3_fm5.fm 10 Product: TDM-20-N / 28.1.1999 4.0.5 Guide Texts And Error Situations After switching power the display shows LOCAL. Along with a local command, a guide text always appears, explaining the given command. The following list shows the most common error situations. ERROR on the display: 1. Error in local command 2. Failed EEPROM programming 3. Wrong input data to EEPROM - Length of data - Erroneus digits - RSSI-levels or deviation limit levels are not in propersuccession 4. Loop test has failed 5. BURN-IN test cannot be activated when not enabled UNKNOW on the display: Unknown local command LOCAL on the display though there is no local box: BURN-IN test is enabled or subscriber number is not programmed. TDM-10E3_fm5.fm 11 Product: TDM-20-N / 28.1.1999 4.0.6 Local-Box 4.0.6.1 General LOCAL = operating mode where it‘ s possible to give commands to set, read and program the MS features. To get the MS to LOCAL a local-boxes, one merely has "service rights" i.e. you cannot program subscriber number. The other has "full rights", i.e. there are no restictions in LOCAL. Each box has it‘ s own serial number. Serial number and programming rights are installed by manufacturer. Serial number is used for identifying the subscriber number programmer and it is stored automatically to MS during programming. There is text LOCAL on the display when the local box is connected and power is switched on. 4.0.6.2 Features Of Local-box Switching ON/OFF the power supply: - Set NORMAL/SERVICE switch NORMAL position To be measured from audio of the radio unit: - Set NORMAL/SERVICE switch SERVICE position and RADIO/HANDSET switch RADIO position. GEN: -norm dev = 1 Vrms - max dev = 3.33 Vrms - norm dev = 300 mVrms - max dev = 600 mVrms (VOL = 0dB) METER: SERVICE/HANDSET To measure handset audios: - Set NORMAL/SERVICE switch NORMAL position and RADIO/HANDSET switch HANDSET positon BNC-connectors: GEN: -norm dev = 300 mVrms - max dev = 600 mVrms METER: 4.0.6.3 Internal Ram Local-box‘ s internal RAM is intended for not losing the contents of shortcode memory during service operations. Commands TDM-10E3_fm5.fm 9# 999* store shortcode memory to local-box store shortcode memory to MS. 12 Product: TDM-20-N / 28.1.1999 5.0 TUNING INSTRUCTIONS 5.0.1 Connect To Phone - operating voltage (13.2V, X800 connector, loudspeaker needed) - local-box (between handset and radio unit) - RF-generator/power-meter 5.0.2 Synthesizer Check-up of operating voltages Input-connector V401 pin1 13.2 V TP1 TP2 TP7 + TX on (local 34#) + TX off (local 34*) 8.6...9.4 V 4.5...5.3 V 13...15 V 8.5...9.3 V TP3 approx 5 V TP3 5.0.3 RX-VCO Switch synthesizer to first channel (local 35#) Measure voltage synthesizer unit TP6, adjust voltage C435( RX-VCO) to 3 V Change to last channel (local 37#) Check that the adjusting voltage is approx 6 V 5.0.4 TX-VCO Start TX-VCO (local 34#) Switch synthesizer to first channel (local 35#) Measure TP4 voltage, adjust voltage by C498 (TX-VCO) to 5 V Change to last channel (local 37#) Check that the adjusting voltage is now approx 7.5...8.5 V TDM-20E5_fm5.fm 1 Product: TDM-20-N / 28.1.1999 5.0.5 Channel Frequency Adjustment Start transmitter (local 33#) Change to first channel (local 35#) Adjust channel frequency MHz (+/-100 Hz) with TCXO trimmer 5.0.6 Transmitter Set operating voltage to 15.6 V Switch on transmitter (local 33#) Adjust audio/pros unit R162 (TX-POW) transmitter power to 41.8 dBm Set operating voltage to 10.8 V, check the transmitter power. Difference max +/-1.5 dB Check 32# 31.8 dBm Check 31# 21.8 dBm 5.0.7 TX-Audio Feed 1 kHz, 1 V RMS signal to local box GEN-connector. Switch on TX-audio, mic off (local 21#, 29*). Measure the processor unit x-synte connector pin 2 , and adjust (maximum) level of R241 to 550 mV RMS. Switch transmitter to medium power, center channel (local 32#, 36#). Adjust R459 (syntyhesizer-module) deviation to 3 kHz. Check the deviation in channels (1, 180); difference must not exceed 150 Hz. Change TX-VCO adjusting voltage if necessary (range in use approx 3...10 V). Adjust R459 (MOD) again. Drop the af.gen level until deviation is 1 kHz, measure V401 pin 2 in synthesizer, write down the level. Change af.gen frequency to 300 Hz. Raise the af.gen level until V401 pin 2 level is equal to the reference level mentioned before. Adjust R457 deviation (with COMP.OS-module) to 1 kHz. TDM-20E5_fm5.fm 2 Product: TDM-20-N / 28.1.1999 5.0.8 Max DEV Feed pt.gen frquency 1 kHz, 3.33 Vrms. Check deviation in channels (1, 90, 180). Deviation must be within the limits 4.0...4.5 kHz; if it exceeds 4.5 kHz, adjust R244 (with MAX OA-module). Reset (local 0#) 5.0.9 FFSKT Switch on medium power (local 32#). Switch on FFSKT (local 12#). Adjust R265 deviation (FFSKT) to 4.2 kHz. Reset (local 0#). 5.0.10 RX-Audio Set RF-generator frequency 465.225 MHz, level -57 dBm, mod freq 1 kHz, deviation 3 KHz. Set channel 90 (local 36#, 22#). Expander ON (local 200#). Adjus LF output level R302 (RX) 300 mV RMS, measure at METER-connector (local-box) Reset (local 0#). 5.0.11 RX-Response Set RF-generator values as above, except for level -113 dBm. Switch on high-power, RXA on (local 33#, 22#) Measure SINAD CCITT min. 20 dB. Also check channels (1, 180). RF-generator frequency 463.000 MHz (35#) 467.475 MHz (37#) 5.0.12 RX-Distortion Set center channel, high-power (local 36#, 33#). RF-generator frequency 465.225 MHz, level -57 dBm. Measure distortion, max 5 %. Reset by 0#. TDM-20E5_fm5.fm 3 Product: TDM-20-N / 28.1.1999 5.0.13 TX-Distortion Set center channel high-power, TXA on, mic off (local 36#, 33#, 21#, 29*). Feed 1 kHz, 1 V RMS signal to local-box GEN-connector. Measure distortion, max 5 % Reset (local 0#). 5.0.14 FII DEV Set RF-generator frequency 465.225 MHz, level -57 dBm, modulation frequency 4 kHz, dev 300 Hz. Switch on fiiloop (local 23#), power (32#). Adjust R255 deviation to 300 Hz. Reset (local 0#). 5.0.15 Tuning The RSSI-Levels Set RF-generator frequency 465.225 MHz, level -53 dBm. Switch on RSSI tuning (local 38#). Display shows "PG-53". Wait until reading on the display settles down. Press OK. Change RF-level to -63 dBm. Phone display shows "PG-63" Press OK. Change RF-level to -93 dBm. Phone display shows "PG-93 Press OK. Change RF-level to -103 dBm. Phone display shows "PG-103 Press OK. TDM-20E5_fm5.fm 4 Product: TDM-20-N / 28.1.1999 Change RF-level to -115 dBm. Phone display shows "PG-115 Press OK. Check tuning (local 38*). 5.0.16 Tuning FSK-split level RF-generator settings Freq. 465.225 MHz, level -53 dBm ,mod freq 1 kHz, dev 350 Hz Give local-command 70#. Handset display show value 20...30. Store value by pressing OK button. 5.0.17 Program Base-Band (if neccessery) Give local command 71#. Press 1 and OK Press 180 and OK. 5.0.18 Programming The Subscriber Number Requires local-box with programming rights. Give local-command 2#. Feed 10 digits, and press OK (country code + subcriber number + password) Check 2*. TDM-20E5_fm5.fm 5 Product: TDM-20-N / OT0001 Transmitter 28.1.1999 6.0 TRANSMITTER MODULE OT0001 SPECIFICATIONS: OT0001 Transmitter Operating voltage 10.8...15.6 VDC Current consumption max 4.5 A Input power level 10 dBm (+2/-2 dB) Output power level max 44 dBm (25 W) without a duplex filter Frequency range 453.000...457.475 MHz 6.0.1 Connector Description: 4-pole connector: pin 1, voltage from directional coupler max 10 V pin 2, control voltage for RF-power max 8 V pin 3, bias for the preamplifiers 8 V pin 4, GND 6.0.1.1 Transmitter operation: The transmitter is a 5-stage amplifier chain. The two preamplifiers (Q600/601) operate in class AB as linear amplifiers. The final amplifier (I600) is a class C power module. The output power is controlled with a loop: A signal coming from the directional coupler is rectified and filtered. Then it is fed through processor controlled voltage attenuator to the integrator, which has a preset reference voltage (a corresponding value for 15 W output power). The control voltage from the integrator is amplified in DC-amplifier (Q610/611) and fed to the preamplifiers/the first stage of the power module. RF-power input has a 6 dB attenuator to improve impedance matching between synthesizer and transmitter in different power level conditions. 6.0.2 Tuning Instructions: Tuning can be done in local mode or using CMT-tester. Set a power supply to 15.6 V. Input signal 10 dBm (10 mW) on channel 090 from the synthesizer or signal generator. Connect a 50 ohm dummy load and a power meter to the antenna connector. Transmitter on (33#). Tune output power with trimmer R162 on OA0014 (audio/processor) -module to 41.8 dBm (15 W). XT0001E4_fm5.fm 1 Product: TDM-20-N / OT0001 Transmitter 28.1.1999 Set a power supply to 10.8 V and check output power. It should be about the same value as set before (+/-1.5 dB). Set a power supply to 13.2 V. Check power levels: High 41.8 dBm (15 W) +/-1.5 dB (33#) Medium 31.8 dBm (1.5 W) +/-3 dB (32#) Low 21.8 dBm (0.15 W) +/-3 dB (31#) Power off (31*) Tuning is completed. Some useful local mode commands for the transmitter operation checking: Channel 001 090 180 35# 36# 37# high power on/off medium power on/ off low power on/off 33#/33* 32#/32* 31#/31* 6.0.3 Test Point Voltages Set the power supply to 13.2 V Typical DC-values measured with a universal meter Ri = 10 Mohm (Philips PM 2505). XT0001E4_fm5.fm Power level H M L TP1 2 3 4 5 2.0 1.4 4.6 0.7 5.5 2.0 1.3 3.4 0.7 3.3 2.0 1.1 2.1 0.7 3.0 2 Product: TDM-20-N / OT0001 Transmitter 28.1.1999 Typical RF-voltages measured with R&S millivoltmeter URV-3. Power level H M L TP1 2 3 4 5 0.4 0.15 0.85 0.28 3.6 0.4 0.06 0.65 0.3 2.7 0.4 0.04 0.55 0.32 2.4 Values can vary +-10 %. All values indicated as volts. XT0001E4_fm5.fm 3 Product: TDM-20-N / OT0001 Transmitter 28.1.1999 6.0.4 Parts list CODE PART DESCRIPT. VALUE MANUF. CC0471 CC0101 CC0101 CC0471 CC0101 CC0101 CC0471 CU0105 CC0472 CC0471 CC0471 CC0471 CE0105 CC0471 CC0471 CC0473 CE0105 CC0471 CC0101 CC0101 CC0101 CC0471 CE0476 CC0473 CE0105 CE0105 CC0101 DZ0569 DY0074 IW0720 LF0396 LF0396 PT0001 QA5634 QA0035 QSB848 QP0032 RC0151 RC0151 RC0390 RC0471 RC0152 RC0330 RC0330 RC0221 RC0331 RC0391 RC0222 RC0223 RC0100 RC0100 RC0100 RC0222 RC0102 RM1502 RC0103 RC0472 C601 C602 C603 C604 C605 C606 C607 C609 C610 C611 C613 C614 C615 C616 C617 C618 C619 C620 C621 C622 C623 C624 C625 C626 C627 C628 C629 D620 D623 I600 L601 L602 PCB Q600 Q601 Q610 Q611 R600 R601 R602 R603 R604 R605 R606 R608 R610 R611 R612 R613 R614 R615 R616 R620 R621 R622 R623 R624 SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD tantal SMD capasitor SMD capasitor SMD capasitor SMD capasitor Al elko SMD capasitor SMD capasitor SMD capasitor Al elko SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor Al elko SMD capasitor Al elko Al elko SMD capasitor SMD zener Shottky diode RF-power amplifier Inductor Inductor PCB for OT0001 SMD RF-transistor SMD RF-transistor SMD transistor Power transistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor Mini-Melf resistor SMD resistor SMD resistor 470 pF 5% 50 V NP0 100 pF 5% 50V NP0 100 pF 5% 50V NP0 470 pF 5% 50 V NP0 100 pF 5% 50V NP0 100 pF 5% 50V NP0 470 pF 5% 50 V NP0 1uF/16V 20% 3.2x1.6mm 4.7 nF 10% 50 V X7R 470 pF 5% 50 V NP0 470 pF 5% 50 V NP0 470 pF 5% 50 V NP0 1uF/63V 4x7mm 470 pF 5% 50 V NP0 470 pF 5% 50 V NP0 47 nF 10% 50 V X7R 1uF/63V 4x7mm 470 pF 5% 50 V NP0 100 pF 5% 50V NP0 100 pF 5% 50V NP0 100 pF 5% 50V NP0 470 pF 5% 50 V NP0 47 uF/25 V 7x7mm 47 nF 10% 50 V X7R 1uF/63V 4x7mm 1uF/63V 4x7mm 100 pF 5% 50V NP0 5V6 5% 300mW Philips Philips Philips Philips Philips Philips Philips Matsushita Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Motorola Philips Philips XT0001E4_fm5.fm 450-460MHz 39 uH 39 uH 155 x 36 x 1.6 NPN 1 W 5 GHz NPN Wideband 1GHz NPN 0.1A/30V F=2dB PNP 3A/60V 150 R 5% 0.125 W 150 R 5% 0.125 W 39 R 5% 0.125 W 470 R 5% 0.125 W 1.5 k 5% 0.125 W 33 R 5% 0.125 W 33 R 5% 0.125 W 220 R 5% 0.125 W 330 R 5% 0.125 W 390 R 5% 0.125 W 2.2 k 5% 0.125 W 22 k 5% 0.125 W 10 R 5% 0.125 W 10 R 5% 0.125 W 10 R 5% 0.125 W 2.2 k 5% 0.125 W 1 k 5% 0.125 W 15k0 1% 0.25W 10 k 5% 0.125 W 4.7 k 5% 0.125 W NEC Philips Philips Philips Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Beyschlag Kamaya Kamaya TYPE ECST1CY 105R 2222 097 58108 2222 097 58108 2222 097 56479 2222 097 58108 2222 097 58108 BZX84C5V6 BAT 74 MHW720A2X NE85634 BFG-35 BC 848 B BDT 32 AF MMA 0204-50 4 Product: TDM-20-N / OT0001 Transmitter 28.1.1999 CODE RC0820 VN0104 VR0235 VR0122 PART R625 V600 V601 V625 DESCRIPT. SMD resistor 4-pin connector Coax cable + connector SMB + coax VALUE 82 R 5% 0.125 W 50 ohm l=n.70mm l=22 cm MANUF. Kamaya Wisher Taikodenki Radiall TYPE WKP-N4B1G-L TMP-P01X-A1 Last update 14.08.91 XT0001E4_fm5.fm 5 Product: TDM-20-N / OT0001 Transmitter 28.1.1999 Component Side Layout PT0001A0 (Schematic OT0001A0) XT0001E4_fm5.fm 6 Product: TDM-20-N / OT0001 Transmitter 28.1.1999 Solder Side Layout PT0001A0 (Schematic OT0001A0) XT0001E4_fm5.fm 7 Product: TDM-20-N / OT0001 Transmitter 28.1.1999 XT0001E4_fm5.fm 8 Product: TDM-20-N / OR0002 Receiver 28.1.1999 7.0 RECEIVER MODULE OR0002 SPECIFICATIONS OR0002 Receiver 7.0.1 Principles Of Receiver Operation The module includes all operational segments of FM receiver. RF-amplifier 1. mixer 1. IF-amplifier FM IF-system BFR93A ASK-1 SST310 SA605D including following functions: 2. local oscillator 2. mixer IF limiter amplifiers quadrature demodulator RSSI (received signal strength indicator) The receiver is connected to the V701 audio/processor unit with a connector. ADAPTERS V701 1 +9 V 2 RSSI 3 RX-AUDIO 4 GND V702:RX-injection receiver operating voltage DC-voltage comparable to field strength (0.5...5 V) AF-signal for audio unit, approx. 150 mVrms (f.mod 1 kHz dev. 3 kHz) ground (chassis) 484.400...488.875 MHz +10 dBm/50 ohm. The receiver RF-signal is brought through the duplex filter NBF40001 to the amplifier stage Q701. The amplifier signal is led the dual balanced mixer X701 through the band filter L703. The upper injection frequency is brought from the synthesizer unit to the LO input of the mixer through a small resistance attenuator. The IF (intermediate frequency) 21.4 MHz gained in this way is amplified and led through crystal filters X702 and X703 to the FM IF-system IC-circuit (SA605D). The circuit includes another local oscillator, and another mixer. The second IF is 455 kHz: there is first a 6-pole ceramic filter, and another 4-pole filter in the limiter amplifier chain. The temperature compensation for the AF-signal indicated has been included in the buffer amplifier stage I702/B. XR0002E4_fm5.fm 1 Product: TDM-20-N / OR0002 Receiver 28.1.1999 The temperature compensation for the RSSI signal has been made with the diode pai D701, which is followed by the buffer amplifier I702/A. The receiver unit gets +9 V regulated operating voltage from the current input unit OW0001 through the audio/processor unit. The operating voltage is dropped with the transistor Q703 to the lower required by the IF circuit. 7.1 Receiver OR0002 settings 7.1.1 Supply Voltages A regulated +9 V power supply is fed to the module via connector V701 pin 1. The intermediate frequency module uses a ca. +6 V supply which can be checked at the solder joint of condenser C727 located on top of the board. 7.1.2 Setting Order: 1. Detector coil V707 2. Crystal filter matching coils L705, L706 3. Helical bandpass filter 1. Adjustment of detector coil L707 is not dependant on the channel used. Feed a -13 dBm RF-signal to the aerial connector. Enable RX audio (local 22#). Connect the local box meter connector to an oscilloscope or AC voltmeter (1 V range). Adjust coil L707 to maximum value. NOTE: (Changing the receiver may cause difference at audio levels. When changing the module, the audio unit RX adjustment should also be checked. If the RX adjustment has been changed, then the FII-deviation must also be checked.) 2. Adjustment of the crystal filter matching coils L705 and L706 is not dependant on the channel used. Feed a -13 dBm modulated RF-signal to the aerial connector. Enable RX audio (local 22#). Connect the local box meter connector to a SINAD meter. Trim coils L705 and L706 for maximum value on the SINAD meter and repeat the adjustment (35...50 dB SINAD psoph.). XR0002E4_fm5.fm 2 Product: TDM-20-N / OR0002 Receiver 28.1.1999 The effect of these coils can be seen even more clearly if the SINAD meter is connected direct to the RX audio output connector V701 pin 3. This simplifies their adjustment. 3. Helical bandpass filter This adjustment influnces spurious response rejection and tuning must be done carefully using suitable plastic screwdriver, which does not disturb tuning. Switch on the first channel (local 35#) Feed to the antenna connector RF-signal at level -93 dBm (463.000 MHz) Connect DC-voltmeter (analog display) 3 V max connector V701 pin 2 RSSI Adjust voltmeter to maximum with helix core nearest to the duplexfilter Change receiver on the highest channel (local 37#) (467.475 MHz) Adjust voltmeter to maximum value with the other core of the helix Change back to the first channel Adjust voltmeter again carefully to maximum value 7.1.3 Check Sensitivities XR0002E4_fm5.fm Channel RF-input SINAD psoph. 001 180 -113 dBm -113 dBm 26...27 dB 26...29 dB (typical values) 3 Product: TDM-20-N / OR0002 Receiver 28.1.1999 7.1.4 Parts list CODE PART DESCRIPT. VALUE MANUF. CC0101 CC0471 CC0471 CD0100 CC0100 CC0150 CC0101 CC0220 CC0103 CD0399 CC0220 CC0473 CC0390 CC0151 CC0473 CC0473 CC0473 CC0473 CD0100 CC0103 CC0473 CC0473 CC0473 CU0225 CC0101 CC0473 CC0331 CC0101 CC0331 DS0099 IV6050 IA0272 LH0465 LC0105 LI0225 LI0225 LI0687 PR0002 QAA093 QF0310 QSB848 RC0472 RC0103 RC0103 RC0221 RC0100 RC0120 RC0391 RC0471 RC0222 RC0101 RC0682 RC0223 RC0223 RC0472 RC0471 RC0152 C701 C702 C703 C704 C705 C706 C707 C708 C709 C711 C712 C713 C714 C715 C716 C717 C718 C719 C721 C722 C724 C725 C726 C727 C728 C729 C730 C731 C732 D701 I701 I702\ L703\ L704 L705 L706 L707 PCB Q701 Q702 Q703 R701 R702 R703 R704 R705 R706 R707 R711 R712 R713 R714 R715 R716 R717 R718 R719 SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD tantal SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD diode FM IF-system 2 x op.amp. Helix filter SMD inductor IF-coil IF-coil Quad coil PCB for OR0002 SMD transistor Transistor SMD transistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor 100 pF 5% 50V NP0 470 pF 5% 50 V NP0 470 pF 5% 50 V NP0 10 pF/0.25pF 50 V NP0 10 pF 5% 50V NP0 15 pF 5% 50V NP0 100 pF 5% 50V NP0 22 pF 5% 50V NP0 10 nF 10% 50V X7R 3.9pF 0.25 50V NP0 22 pF 5% 50V NP0 47 nF 10% 50 V X7R 39pF 5% 50V NP0 150 pF 5% 50V NP0 47 nF 10% 50 V X7R 47 nF 10% 50 V X7R 47 nF 10% 50 V X7R 47 nF 10% 50 V X7R 10 pF/0.25pF 50 V NP0 10 nF 10% 50V X7R 47 nF 10% 50 V X7R 47 nF 10% 50 V X7R 47 nF 10% 50 V X7R 2.2uF/16V 20% 4.7x2.6mm 100 pF 5% 50V NP0 47 nF 10% 50 V X7R 330 pF 5% 50 V NP0 100 pF 5% 50V NP0 330 pF 5% 50 V NP0 70 V 200 mA Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Matsushita Philips Philips Philips Philips Philips Philips Philips Texas Neosid Siemens Toko Toko Toko XR0002E4_fm5.fm LinCMOS Low noise,power 450 MHz 1.0 uH 2.2uH 2.2uH 680uH 90.5 x 37 x 1.6 NPN 0.25 W 5 GHz N-fet NPN 0.1A/30V F=2dB 4.7 k 5% 0.125 W 10 k 5% 0.125 W 10 k 5% 0.125 W 220 R 5% 0.125 W 10 R 5% 0.125 W 12 R 5% 0.125 W 390 R 5% 0.125 W 470 R 5% 0.125 W 2.2 k 5% 0.125 W 100 R 5% 0.125 W 6.8 k 5% 0.125 W 22 k 5% 0.125 W 22 k 5% 0.125 W 4.7 k 5% 0.125 W 470 R 5% 0.125 W 1.5 k 5% 0.125 W Philipsa Siliconix Philips Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya TYPE ECST1CB 225R BAV 99 SA605D TLC27M2ID 7.2E 00519630 B82412-A1102-M 5SPN-0225AG 5S 5SPN-0225AG 5S 7MC-A2549HM 7P Perstorp BFR 93 A SST 310 BC 848 B 4 Product: TDM-20-N / OR0002 Receiver 28.1.1999 CODE RC0473 RC0473 RTN223 RC0273 RC0103 RC0104 RC0474 RC0473 RC0102 RC0153 VN0104 VR0135 XM0001 XF4214 XF4214 X20945 XC6455 XC0455 PART R720 R721 R722 R723 R724 R725 R726 R727 R728 R729 V701 V702 X701 X702 X703 X704 X705 X706 DESCRIPT. SMD resistor SMD resistor SMD-NTC resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor 4-pin connector Coax connector Dual bal. mixer Crystal filter Crystal filter Crystal Ceramic filter Ceramic Filter VALUE 47 k 5% 0.125 W 47 k 5% 0.125 W 22k 10% 27 k 5% 0.125 W 10 k 5% 0.125 W 100 k 5% 0.125 W 470 k 5% 0.125 W 47 k 5% 0.125 W 1 k 5% 0.125 W 15 k 5% 0.125 W 50 ohm 1-600 MHz 4-pole monol 21.4MHz 4-pole monol 21.4MHz 20.945MHz 6-pole 455 kHz 4-pole 455 kHz MANUF. Kamaya Kamaya Hokuriku Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Wisher Taikodenki Mini Circ. SUNNY-EMI SUNNY-EMI Telequarz Kyocera Kyocera TYPE WKP-N4B1G-L TMP-J02X-A1 ASK-1-X65 HC-45/U-2L KBF-455R-20A KBF-455P-20A Last update 14.08.91 XR0002E4_fm5.fm 5 Product: TDM-20-N / OR0002 Receiver 28.1.1999 Component Side Layout PR0002A0 (Schematic OR0002A1) XR0002E4_fm5.fm 6 Product: TDM-20-N / OR0002 Receiver 28.1.1999 Solder Side Layout PR0002A0 (Schematic OR0002A1) XR0002E4_fm5.fm 7 Product: TDM-20-N / OR0002 Receiver 28.1.1999 XR0002E4_fm5.fm 8 Product: TDM-20-N / OS0021 Synthesizer 28.1.1999 8.0 SYNTHESIZER MODULE OS0021 SPECIFICATIONS OS0021 Synthesizer 8.0.1 Functions This unit generates the high frequency signals for respective channel frequencies: this gives a modulated channel-frequency signal for the transmitter unit and upper band injection frequency for the receiver unit. The synthesizer is connected via connector V401 to the processor/audio unit. Description of connector V401: 1VB 2 TXAUDIO 3 GND 4 SRE 5 STE 6 SCLK 7 SDAT 8 TXVCO V403 V402 operating voltage to synthesizer tx audio modulation ground(-) enable pulse for rx synthesizer IC enable pulse for tx synthesizer IC clock for rx and tx data Arx and tx data for synthesizer IC voltage for tx vco. start-up TX-INJECTION MHz +10 dBm/50 ohm RX-INJECTION MHz +10 dBm/50 ohm 13.2 V nominal 550 mV RMS 5V 5V 0/5 V 0/5 V 5V 8.0.2 Circuit Description The module can be divided into three main units: TX-synthesizer, RX-synthesizer, and common power supply unit for both synthesizers. The power supply unit provides stabilized voltages +9 V (TP1) for the high-frequency parts and +5 V (TP2) for the synthesizer and pre-scaler circuits and TCXO. The active components Q401...Q405 are included in the power supply unit. 8.0.3 RX-Synthesizer Receiver injection frequency is generated by a phase-locked loop (PLL). The coil of the voltage-controlled oscillator is a strip line on the PCB. VCO center frequency is adjusted with trimmer C436. Q411 is the oscillator transistor. Next, there are two amplifier stages Q412 and Q413. The circuit is provided with a 3 dB atttenuator for the outcoming signal, with a part of this signal being fed to the pre-scaler I4022. This is called the dual modulus divider having scaling factors 128/129. The divided frequency is fed to the synthesizer circuit I401. XS0001E4_fm5.fm 1 Product: TDM-20-N / OS0021 Synthesizer 28.1.1999 The synthesizer circuit I401 gets its control signals from the processor unit via connector V401 in serial form. Signal CLK is the clock-frequency for synchronising the transmission of channel-frequency data to the synthesizer. The scaler information is stored by a latch-pulse on SRE bus sent to the synthesizeer circuit. The divided frequency is compared to the reference frequency with a phase comparator. The exact reference frequency comes from the thermal-compensated crystal CXO). This 12.8 MHz frequency is divided by a factor of 512 in the synthesizer circuit, giving the reference frequency of 25 kHz (= channel space). The synthesizer is phase-locked when these two frequncies fed to the phase comparator are equal. The phase comparator emits positive pulses in response to low VCO frequency, and ground pulses for high VCO frequency. The phase comparator output chargers and dischargers the capacitor C417 through the resistor R422, while R423 and paralled-connected capacitors C418/419 stabilizing the loop function. The voltage fed to the above described capacitor is amplified with transistors Q408/ 409. Two RC-loops R427/C422 and R428/C433 prevent the pulse transfer from the phase comparator to the VCO. The filtered DC voltage alers, when needed, the reversed voltage of the capacitance-diode D403 located in the oscillator circuit, i.e. controls the VCO frequency (TP6). 8.0.4 TX-Synthesizer TX-frequency is generated with a similar phase-locked loop to the above described Rs-injection frequency. There are after the VCO three buffer amplifiers Q416, Q417, and Q418. The divider and synthesizer circuits function like the RX-synthesizer. There are common DATA and CLK signals. The scaler information is stored by a latch-pulse on STE bus sent to the synthesizer circuit I403. TX-synthesizer uses the phase comparator outputs φ/R and φ/V . This is followed by avtive low-pass filter for control filtering. The VCO control voltage range is widened by raising the filter IC power supply with a voltage converter Q414 (TP7). This filtered control voltage is fed to the capacitance-diode-cathode in the oscillator circuit. An excessive VCO frequency prompts φ /V output-pulses from the phase comparator, but the φ /R output will stay in "1"-state. Too low VCO frequency prompts in turn negative O/R output-pulses from the phase comparator, while the O/V output stays in "1"-state. Modulation is taken from the connector V401 pin 2 (TP5) via level control R459 to the capacitancediode anode of the VCO circuit. With this arrangement the loop filter does not affect the modulation by attenuating the high frequencies. With low modulation frequencies (300...500 Hz), linear AF-response is maintained by feeding the loop with a "compensation modulation" through the integrator I405. Compensation is adjusted with trimmer R457 so that the AF-response is linear at 300 Hz frequency. XS0001E4_fm5.fm 2 Product: TDM-20-N / OS0021 Synthesizer 28.1.1999 8.1 Synthesizer OS0021 Settings When measuring, a multimeter with Ri = 10 M ohm has been used. AC-range 20 Hz...20 kHz. 8.1.1 Checking Operating Voltages Input operating voltage, connector V401 pin 1 (13.2 V) +9 V, regulated +5V, regulated +14V +TX on +TXoff TP1 TP2 TP7 TP3(local 34#) TP3(local 34*) 8.6...9.4 V 4.5...5.3 V 13...15 V 8.5...9.3 V approx 5...7 V Operating voltages require no adjustment. + 9 V accuracy is affected by the Zerner diode V401 (5V6). Accuracy of this diode is 5% in 0-series. It will be changed to 2% diode. The resistors R408, R409 used for voltage settings have 1% tolerance. The + 5 V voltage reference is also taken from this 5V6 diode. 8.1.2 RX-VCO Adjustment Change to lowest channel (local 35#) Measure voltage TP6, adjust voltage RX-VCO to 3 V with trimmer C436. Change to highest channel (local 37#) Check that adjustment voltage is now approx 6 V. (Synthesizer functions are optimized with above VCO settings-accuracy, channel delay, overlap, channel selectivity). (VCO-accuracy = voltage difference between end channels) 8.1.3 TX-VCO Adjustment Switch on TX VCO (local 34#) or transmitter (local 32#) Change lowest channel (local 35#) Measure TP4 voltag, and adjust TX-VCO voltage to 5 V with trimmer C498. Change to highest channel (local 37#) Check that operating voltage is now approx 7.5...8 V. XS0001E4_fm5.fm 3 Product: TDM-20-N / OS0021 Synthesizer 28.1.1999 The operating voltage range has been raised to 13V. It may be necessary to deviate from the above settings in some production runs in order to ensure linear modulation for end channels.In practice the operating voltage can be between 3V...10V. 8.1.4 Setting Channel Frequency: 8.1.4.1 Measuring Devices: Frequency counter (resolution 10 Hz) Switch TX on (local 32#) Switch to lowest channel (local 35#) Set correct channel frequency MHz with TCXO trimmer (+/-100 Hz) 8.1.5 Adjusting The Modulation: Adjust the modulation along wIth the audio unit; see setting instructions for the audio unit, TX-AUDIO. Set to middle channel (local 36#) Switch TX on (local 32#) e.g. medium power. Feed "normal" modulation to microphone input (f mod. 1 kHz 1 Vrms) Switch microphone off (local 29*) Switch TX-audio on (local 21#) Check that TP5 voltage is now 550 mV rms. Adjust deviation to +/-3 kHz peak with MOD-trimmer R459. Check deviation of end channels, difference max +/-150 Hz or +/-0.5 dB 8.1.6 Correcting The Low-frequency Response: Drop mic input level until deviation is +/-1 kHz. Measure TP5 voltage (reference level). Change modulation frequency to 300 Hz. Raise mic input level until TP5 voltage increases to the same level as the reference level. Adjust deviation to +/-1 kHz with COMP-trimmer R457. XS0001E4_fm5.fm 4 Product: TDM-20-N / OS0021 Synthesizer 28.1.1999 8.1.7 Parts list CODE PART DESCRIPT. VALUE MANUF. CC0473 CE0476 CC0102 CU0105 CE0476 CU0105 CC0102 CC0473 CD0101 CC0101 CU0105 CC0101 CC0102 CC0102 CC0473 CC0103 CC0473 CC0473 CC0103 CC0223 CU0105 CC0471 CD0569 CD0100 CD0479 CC0473 CD0279 CD0109 CC0103 CD0689 CA0200 CC0101 CC0471 CC0471 CC0471 CD0100 CD0569 CC0471 CD0829 CD0569 CC0101 CC0101 CC0101 CC0103 CE0105 CC0473 CC0473 CC0473 CU0105 CU0105 CC0101 CC0101 CC0473 CC0223 CC0223 CC0101 CC0102 C401 C402 C403 C404 C405 C407 C408 C409 C410 C411 C412 C413 C414 C415 C416 C417 C418 C419 C421 C422 C423 C424 C425 C426 C427 C428 C431 C432 C433 C434 C435 C436 C437 C438 C439 C441 C442 C443 C444 C445 C460 C461 C462 C463 C464 C465 C466 C467 C468 C469 C471 C472 C473 C474 C475 C476 C477 SMD capasitor Al elko SMD capasitor SMD tantal Al elko SMD tantal SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD tantal SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD tantal SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor Trim.kond. SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor Al elko SMD capasitor SMD capasitor SMD capasitor SMD tantal SMD tantal SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor 47 nF 10% 50 V X7R 47 uF/25 V 7x7mm 1 nF 5% 50V NP0 1uF/16V 20% 3.2x1.6mm 47 uF/25 V 7x7mm 1uF/16V 20% 3.2x1.6mm 1 nF 5% 50V NP0 47 nF 10% 50 V X7R 100 pF 5% 50 V NP0 100 pF 5% 50V NP0 1uF/16V 20% 3.2x1.6mm 100 pF 5% 50V NP0 1 nF 5% 50V NP0 1 nF 5% 50V NP0 47 nF 10% 50 V X7R 10 nF 10% 50V X7R 47 nF 10% 50 V X7R 47 nF 10% 50 V X7R 10 nF 10% 50V X7R 22 nF 10% 50 V X7R 1uF/16V 20% 3.2x1.6mm 470 pF 5% 50 V NP0 5.6 pF/0.25pF 50 V NP0 10 pF/0.25pF 50 V NP0 4.7 pF/0.25pF 50 V NP0 47 nF 10% 50 V X7R 2.7 pF/0.25pF 50 V NP0 1 pF/0.25pF 50 V NP0 10 nF 10% 50V X7R 6.8 pF/0.25pF 50 V NP0 5/20 pF 100 pF 5% 50V NP0 470 pF 5% 50 V NP0 470 pF 5% 50 V NP0 470 pF 5% 50 V NP0 10 pF/0.25pF 50 V NP0 5.6 pF/0.25pF 50 V NP0 470 pF 5% 50 V NP0 8p2/0.25pF 50V NP0 5.6 pF/0.25pF 50 V NP0 100 pF 5% 50V NP0 100 pF 5% 50V NP0 100 pF 5% 50V NP0 10 nF 10% 50V X7R 1uF/63V 4x7mm 47 nF 10% 50 V X7R 47 nF 10% 50 V X7R 47 nF 10% 50 V X7R 1uF/16V 20% 3.2x1.6mm 1uF/16V 20% 3.2x1.6mm 100 pF 5% 50V NP0 100 pF 5% 50V NP0 47 nF 10% 50 V X7R 22 nF 10% 50 V X7R 22 nF 10% 50 V X7R 100 pF 5% 50V NP0 1 nF 5% 50V NP0 Philips Philips Philips Matsushita Philips Matsushita Philips Philips Philips Philips Matsushita Philips Philips Philips Philips Philips Philips Philips Philips Philips Matsushita Philips Philips Philips Philips Philips Philips Philips Philips Philips Matsushita Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Matsushita Matsushita Philips Philips Philips Philips Philips Philips Philips XS0001E4_fm5.fm TYPE 2222 097 56479 ECST1CY 105R 2222 097 56479 ECST1CY 105R ECST1CY 105R ECST1CY 105R ECRLA020E52V 2222 097 58108 ECST1CY 105R ECST1CY 105R 5 Product: TDM-20-N / OS0021 Synthesizer 28.1.1999 CODE CC0102 CC0473 CC0472 CC0473 CC0473 CC0472 CC0473 CC0223 CC0471 CC0473 CU0105 CD0100 CC0150 CD0100 CC0101 CD0479 CD0829 CA0200 CU0105 CD0109 CC0223 CC0471 CC0471 CD0479 CC0471 CC0471 CC0223 CC0150 CD0120 CC0471 CC0120 CC0150 DZ0569 DS0099 DC0031 DS0099 DC0031 DC0031 IS5158 IS0501 IS5158 IS0501 IA0272 LC0334 LC0334 LC0334 LC0334 LC0334 LC0334 PS0001 QS0031 QSB858 QSB848 QSB848 QSB848 QS0031 QSB848 QSC849 QSC859 QAA093 PART C478 C479 C481 C482 C483 C484 C485 C486 C487 C488 C489 C491 C492 C493 C494 C496 C497 C498 C501 C502 C504 C505 C506 C507 C508 C509 C510 C511 C512 C513 C515 C516 D401 D402 D403 D404 D405 D406 I401 I402 I403 I404 I405\ L401 L402 L403 L408 L409 L412 PCB Q401 Q402 Q403 Q404 Q405 Q406 Q407 Q408 Q409 Q411 XS0001E4_fm5.fm DESCRIPT. SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD tantal SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor Trim.kond. SMD tantal SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD zener SMD diode Cap.diode SMD diode Cap.diode Cap.diode PLL freq.synthes. Two mod. prescaler PLL freq.synthes. Two mod. prescaler 2 x op.amp. SMD inductor SMD inductor SMD inductor SMD inductor SMD inductor SMD inductor Piirilevy OS0001 SMD transistor SMD transistor SMD transistor SMD transistor SMD transistor SMD transistor SMD transistor SMD transistor SMD transistor SMD transistor VALUE 1 nF 5% 50V NP0 47 nF 10% 50 V X7R 4.7 nF 10% 50 V X7R 47 nF 10% 50 V X7R 47 nF 10% 50 V X7R 4.7 nF 10% 50 V X7R 47 nF 10% 50 V X7R 22 nF 10% 50 V X7R 470 pF 5% 50 V NP0 47 nF 10% 50 V X7R 1uF/16V 20% 3.2x1.6mm 10 pF/0.25pF 50 V NP0 15 pF 5% 50V NP0 10 pF/0.25pF 50 V NP0 100 pF 5% 50V NP0 4.7 pF/0.25pF 50 V NP0 8p2/0.25pF 50V NP0 5/20 pF 1uF/16V 20% 3.2x1.6mm 1 pF/0.25pF 50 V NP0 22 nF 10% 50 V X7R 470 pF 5% 50 V NP0 470 pF 5% 50 V NP0 4.7 pF/0.25pF 50 V NP0 470 pF 5% 50 V NP0 470 pF 5% 50 V NP0 22 nF 10% 50 V X7R 15 pF 5% 50V NP0 12 pF 5% 50 V NP0 470 pF 5% 50 V NP0 12 pF 5% 50V NP0 15 pF 5% 50V NP0 5V6 5% 300mW 70 V 200 mA UHF 70 V 200 mA UHF UHF CMOS (2nd MC12022D Motorola) CMOS (2nd MC12022D Motorola) LinCMOS Low noise,power 330 nH 330 nH 330 nH 330 nH 330 nH 330 nH 66 x 130 x 1.6 PNP 1A/60V PNP 0.1A/30V F<10dB NPN 0.1A/30V F=2dB NPN 0.1A/30V F=2dB NPN 0.1A/30V F=2dB PNP 1A/60V NPN 0.1A/30V F=2dB NPN 0.2A/30V F=1.2dB PNP 0.2A/30V F=1.2dB NPN 0.25 W 5 GHz MANUF. Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Matsushita Philips Philips Philips Philips Philips Philips Matsushita Matsushita Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Motorola Fujitsu Motorola Fujitsu Texas Siemens Siemens Siemens Siemens Siemens Siemens Philips Philips Philips Philips Philips Philips Philips Philips Philips Philipsa TYPE ECST1CY 105R ECRLA020E52V ECST1CY 105R BZX84C5V6 BAV 99 BBY 31 BAV 99 BBY 31 BBY 31 MC145158-1P MB501LPF MC145158-1P MB501LPF TLC27M2ID B82412A3331M B82412A3331M B82412A3331M B82412A3331M B82412A3331M B82412A3331M Perstorp BSR 31 BC 858 B BC 848 B BC 848 B BC 848 B BSR 31 BC 848 B BC 849 C BC 859 C BFR 93 A 6 Product: TDM-20-N / OS0021 Synthesizer 28.1.1999 CODE QAA093 QAA093 QSB848 QAA093 QAA093 QAA093 QAA093 RC0473 RC0102 RC0103 RC0222 RC0472 RC0102 RC0102 RM1002 RM5621 RC0101 RC0101 RC0104 RC0331 RC0472 RC0104 RC0104 RC0100 RC0102 RC0222 RC0100 RC0822 RC0223 RC0473 RC0472 RC0332 RC0472 RC0103 RC0101 RC0101 RC0153 RC0472 RC0101 RC0332 RC0221 RC0223 RC0102 RC0562 RC0221 RC0223 RC0471 RC0560 RC0221 RC0180 RC0271 RC0473 RC0102 RC0105 RC0473 RC0473 RC0224 RQ0103 RC0222 RQ0103 PART Q412 Q413 Q414 Q415 Q416 Q417 Q418 R401 R402 R403 R404 R405 R406 R407 R408 R409 R411 R412 R413 R414 R415 R416 R417 R418 R419 R420 R421 R422 R423 R424 R425 R426 R427 R428 R431 R432 R433 R434 R435 R436 R437 R438 R439 R441 R442 R443 R444 R445 R446 R447 R448 R451 R452 R453 R454 R455 R456 R457 R458 R459 XS0001E4_fm5.fm DESCRIPT. SMD transistor SMD transistor SMD transistor SMD transistor SMD transistor SMD transistor SMD transistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor Mini-Melf resistor Mini-Melf resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor Trimmer resistor SMD resistor Trimmer resistor VALUE NPN 0.25 W 5 GHz NPN 0.25 W 5 GHz NPN 0.1A/30V F=2dB NPN 0.25 W 5 GHz NPN 0.25 W 5 GHz NPN 0.25 W 5 GHz NPN 0.25 W 5 GHz 47 k 5% 0.125 W 1 k 5% 0.125 W 10 k 5% 0.125 W 2.2 k 5% 0.125 W 4.7 k 5% 0.125 W 1 k 5% 0.125 W 1 k 5% 0.125 W 10k0 1% 0.25W 5k62 1% 0.25W 100 R 5% 0.125 W 100 R 5% 0.125 W 100 k 5% 0.125 W 330 R 5% 0.125 W 4.7 k 5% 0.125 W 100 k 5% 0.125 W 100 k 5% 0.125 W 10 R 5% 0.125 W 1 k 5% 0.125 W 2.2 k 5% 0.125 W 10 R 5% 0.125 W 8.2 k 5% 0.125 W 22 k 5% 0.125 W 47 k 5% 0.125 W 4.7 k 5% 0.125 W 3.3 k 5% 0.125 W 4.7 k 5% 0.125 W 10 k 5% 0.125 W 100 R 5% 0.125 W 100 R 5% 0.125 W 15 k 5% 0.125 W 4.7 k 5% 0.125 W 100 R 5% 0.125 W 3.3 k 5% 0.125 W 220 R 5% 0.125 W 22 k 5% 0.125 W 1 k 5% 0.125 W 5.6 k 5% 0.125 W 220 R 5% 0.125 W 22 k 5% 0.125 W 470 R 5% 0.125 W 56 R 5% 0.125 W 220 R 5% 0.125 W 18 R 5% 0.125 W 270 R 5% 0.125 W 47 k 5% 0.125 W 1 k 5% 0.125 W 1 M 5% 0.125 W 47 k 5% 0.125 W 47 k 5% 0.125 W 220 k 5% 0.125 W 10k 20% 0.5W 2.2 k 5% 0.125 W 10k 20% 0.5W MANUF. Philipsa Philipsa Philips Philipsa Philipsa Philipsa Philipsa Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Beyschlag Beyschlag Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Bourns Kamaya Bourns TYPE BFR 93 A BFR 93 A BC 848 B BFR 93 A BFR 93 A BFR 93 A BFR 93 A MMA 0204-50 MMA 0204-50 3329H-1-103 3329H-1-103 7 Product: TDM-20-N / OS0021 Synthesizer 28.1.1999 CODE RC0222 RC0103 RC0222 RC0100 RC0102 RC0473 RC0472 RC0472 RC0223 RC0223 RC0104 RC0473 RC0222 RC0222 RC0222 RC0101 RC0101 RC0472 RC0560 RC0103 RC0153 RC0472 RC0102 RC0332 RC0223 RC0102 RC0221 RC0562 RC0223 RC0471 RC0221 RC0562 RC0223 RC0331 RC0680 RC0121 RC0270 RC0181 VN0108 VR0235 VR0135 XO0128 PART R460 R461 R471 R472 R473 R474 R475 R476 R477 R478 R479 R481 R482 R483 R484 R491 R492 R493 R494 R495 R497 R498 R501 R502 R503 R504 R505 R506 R507 R508 R511 R512 R513 R514 R515 R516 R517 R518 V401 V402 V403 X401 DESCRIPT. SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor 8-pin connector Coax cable + connector Coax connector TCXO VALUE 2.2 k 5% 0.125 W 10 k 5% 0.125 W 2.2 k 5% 0.125 W 10 R 5% 0.125 W 1 k 5% 0.125 W 47 k 5% 0.125 W 4.7 k 5% 0.125 W 4.7 k 5% 0.125 W 22 k 5% 0.125 W 22 k 5% 0.125 W 100 k 5% 0.125 W 47 k 5% 0.125 W 2.2 k 5% 0.125 W 2.2 k 5% 0.125 W 2.2 k 5% 0.125 W 100 R 5% 0.125 W 100 R 5% 0.125 W 4.7 k 5% 0.125 W 56 R 5% 0.125 W 10 k 5% 0.125 W 15 k 5% 0.125 W 4.7 k 5% 0.125 W 1 k 5% 0.125 W 3.3 k 5% 0.125 W 22 k 5% 0.125 W 1 k 5% 0.125 W 220 R 5% 0.125 W 5.6 k 5% 0.125 W 22 k 5% 0.125 W 470 R 5% 0.125 W 220 R 5% 0.125 W 5.6 k 5% 0.125 W 22 k 5% 0.125 W 330 R 5% 0.125 W 68 R 5% 0.125 W 120 R 5% 0.125 W 27 R 5% 0.125 W 180 R 5% 0.125 W 50 ohm l=n.70mm 50 ohm 12.8 MHz 2 ppm MANUF. Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Wisher Taikodenki Taikodenki Toyocom TYPE WKP-N8B1G-L TMP-P01X-A1 TMP-J02X-A1 TCO-903B1 Last update 13.03.90 XS0001E4_fm5.fm 8 Product: TDM-20-N / OS0021 Synthesizer 28.1.1999 Component Side Layout PS0001A0 (Schematic OS0001A0) XS0001E4_fm5.fm 9 Product: TDM-20-N / OS0021 Synthesizer 28.1.1999 Solder Side Layout PS0001A0 (Schematic OS0001A0) XS0001E4_fm5.fm 10 Product: TDM-20-N / OS0021 Synthesizer 28.1.1999 XS0001E4_fm5.fm 11 Product: TDM-20-N / OW0002 Power supply 28.1.1999 9.0 POWER SUPPLY MODULE OW0002 SPECIFICATIONS OW0002 Power supply P.S.U. includes noise filter, 9 V-regulator, speaker amplifier, and relay drivers. 9.0.1 Connector X800 1 MUTE 2 3 IGS GND 4 AL 5 6 SPKR VB CAR RADIO MUTE relay-driver 0.5A IGNITION SENSE GROUND EXTERNAL ALARM relaydriver 0.5A SPEAKER SUPPLY VOLTAGE 4...8 ohm 10.8...15.6 V 5A 9.0.2 Connector X820 1 2 3 4 5 6 7 8 12 V 9V BCUP PWR AFIN IGN EXAL EXMUTE 12V for processor module 9 V regulator 8.5...9 V BACK-UP power supply for RAM-memory ON/OFF control audio input for speaker amplifier IGNITION control EXTERNAL ALARM control CAR RADIO MUTE control 1A 9.0.3 Connector X830 1 +TX SUPPLY VOLTAGE FOR TRANSMITTER 9.0.4 Operation Principles: Noise from vehicle electrical-system is filtered with low-pass filter C810, C811, L810, C813, C812, L811, and zenerdiode D812. Main relay A800 in driven from connector X820/4(5 V). The speaker must be connected to X800/5, or otherwise transistor Q813 conducts and cannot swich the power ON. D811, D814, and transistor Q810 prevent switching power ON when supply voltage is too high. The output voltage of the regulator is set by R806, R807, and zenerdiode D800, and current limit by R803. Speaker amplifier is in stand-by position (low current-consumption) when there is no blas voltage in connector X820/5. XW0002E4_fm5.f 1 Product: TDM-20-N / OW0002 Power supply 28.1.1999 9.0.5 Parts list CODE PART DESCRIPT. VALUE MANUF. TYPE AR0002 CC0473 CE0106 CC0222 CC0473 CP0104 CP0104 CE0228 CE0477 CE0107 CE0476 CC0473 CE0107 CC0222 CE0477 CC0222 CC0222 CC0222 CC0222 CE0476 CC0473 CE0107 CP0104 CC0222 CP0104 CC0473 CP0104 CC0222 CC0223 CC0473 DZ1569 DS0070 DS0017 DS0017 DT0018 DS0017 DZ0180 DS0070 DS0017 DS0017 IA1020 LA5107 VI0040 VI0040 VI0040 VI0040 VI0040 VI0040 PW0002 QP0032 QS0051 QSB848 QSB848 QSB848 QSB848 QS0054 QSB848 A800\ C800 C801 C802 C803 C810 C811 C812 C813 C814 C815 C816 C817 C818 C819 C820 C821 C822 C823 C824 C825 C826 C827 C828 C829 C830 C831 C832 C833 C834 D800 D801 D810 D811 D812 D813 D814 D815 D816 D817 I800 L810 MEK1 MEK2 MEK3 MEK4 MEK5 MEK6 PCB Q800 Q801 Q802 Q803 Q810 Q811 Q812 Q813 Relay SMD capasitor Al elko SMD capasitor SMD capasitor Polyester cap Polyester cap Al elko Al elko Al elko Al elko SMD capasitor Al elko SMD capasitor Al elko SMD capasitor SMD capasitor SMD capasitor SMD capasitor Al elko SMD capasitor Al elko Polyester cap SMD capasitor Polyester cap SMD capasitor Polyester cap SMD capasitor SMD capasitor SMD capasitor SMD zener SMD diode pair SMD diode SMD diode Transient filter SMD diode SMD zener SMD diode pair SMD diode SMD diode Audio power amplifier Inductor Component base Component base Component base Component base Component base Component base PCB for OW0002 Power transistor SMD transistor SMD transistor SMD transistor SMD transistor SMD transistor SMD transistor SMD transistor 12V/10A 47 nF 10% 50 V X7R 10 uF/35 V 5x7mm 2.2 nF 5% 50 V NP0 47 nF 10% 50 V X7R 100n 63V 20% 100n 63V 20% 2200 uF/25 V 16x25 470 uF/25 V 10x25mm 100uF 16V 7x7mm 47 uF/25 V 7x7mm 47 nF 10% 50 V X7R 100uF 16V 7x7mm 2.2 nF 5% 50 V NP0 470 uF/25 V 10x25mm 2.2 nF 5% 50 V NP0 2.2 nF 5% 50 V NP0 2.2 nF 5% 50 V NP0 2.2 nF 5% 50 V NP0 47 uF/25 V 7x7mm 47 nF 10% 50 V X7R 100uF 16V 7x7mm 100n 63V 20% 2.2 nF 5% 50 V NP0 100n 63V 20% 47 nF 10% 50 V X7R 100n 63V 20% 2.2 nF 5% 50 V NP0 22 nF 10% 50 V X7R 47 nF 10% 50 V X7R 5V6 2% 300mW 70V/100mA common cathode 1.5A/400V 1.5A/400V 18V/50A 1500W 1.5A/400V 18V 5% 300mW 70V/100mA common cathode 1.5A/400V 1.5A/400V 7W/14.4V/4ohm 100uH 5A 1 base = 40 holes 1 base = 40 holes 1 base = 40 holes 1 base = 40 holes 1 base = 40 holes 1 base = 40 holes 149 x 56 x 1.6mm FR4 PNP 3A/60V PNP 1.5A/45V NPN 0.1A/30V F=2dB NPN 0.1A/30V F=2dB NPN 0.1A/30V F=2dB NPN 0.1A/30V F=2dB NPN 1.5A/45V NPN 0.1A/30V F=2dB Guardian Philips Philips Philips Philips Wima Wima Elna ROE Philips Philips Philips Philips Philips ROE Philips Philips Philips Philips Philips Philips Philips Wima Philips Wima Philips Wima Philips Philips Philips Philips Philips Philips Philips Motorola Philips Philips Philips Philips Philips Philips Fuji Perlos Perlos Perlos Perlos Perlos Perlos 1655S-IC-12D Philips Philips Philips Philips Philips Philips Philips Philips BDT 32 AF BCX 51 BC 848 B BC 848 B BC 848 B BC 848 B BCX 54 BC 848 B XW0002E4_fm5.f 2222 097 50109 RE2-25V222M EB00GD347E00R 2222 097 55101 2222 097 56479 2222 097 55101 EB00GD347E00R 2222 097 56479 2222 097 55101 BZX84B5V6 BAV 70 BYD 17 G BYD 17 G ICTE-18 BYD 17 G BZX84C18 BAV 70 BYD 17 G BYD 17 G TDA1020/N4 SL05B101 2 Product: TDM-20-N / OW0002 Power supply 28.1.1999 CODE QS0054 QSB848 QS0054 QSB848 QSB848 QSB858 RC0473 RC0102 RC0103 RA0681 RC0472 RC0102 RM6041 RM1002 RC0330 RC0103 RC0103 RC0103 RC0103 RC0104 RC0473 RC0473 RC0104 RC0473 RC0104 RC0104 RC0334 RC0104 RC0104 RA0479 RC0103 RC0104 RC0393 RC0102 VW0106 VN0208 PART Q814 Q815 Q816 Q817 Q818 Q819 R800 R801 R802 R803 R804 R805 R806 R807 R810 R812 R813 R814 R815 R816 R817 R818 R819 R820 R821 R824 R825 R826 R827 R828 R829 R830 R831 R832 X800 X820 DESCRIPT. SMD transistor SMD transistor SMD transistor SMD transistor SMD transistor SMD transistor SMD resistor SMD resistor SMD resistor Metal film resistor SMD resistor SMD resistor Mini-Melf resistor Mini-Melf resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor Metal film resistor SMD resistor SMD resistor SMD resistor SMD resistor Connector 8-pin connector VALUE NPN 1.5A/45V NPN 0.1A/30V F=2dB NPN 1.5A/45V NPN 0.1A/30V F=2dB NPN 0.1A/30V F=2dB PNP 0.1A/30V F<10dB 47 k 5% 0.125 W 1 k 5% 0.125 W 10 k 5% 0.125 W 680R 5% 0.25 W 4.7 k 5% 0.125 W 1 k 5% 0.125 W 6k04 1% 0.25W 10k0 1% 0.25W 33 R 5% 0.125 W 10 k 5% 0.125 W 10 k 5% 0.125 W 10 k 5% 0.125 W 10 k 5% 0.125 W 100 k 5% 0.125 W 47 k 5% 0.125 W 47 k 5% 0.125 W 100 k 5% 0.125 W 47 k 5% 0.125 W 100 k 5% 0.125 W 100 k 5% 0.125 W 330 k 5% 0.125 W 100 k 5% 0.125 W 100 k 5% 0.125 W 4R7 5% 0.25 W 10 k 5% 0.125 W 100 k 5% 0.125 W 39 k 5% 0.125 W 1 k 5% 0.125 W male 6-pin MANUF. Philips Philips Philips Philips Philips Philips Kamaya Kamaya Kamaya Philips Kamaya Kamaya Beyschlag Beyschlag Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Philips Kamaya Kamaya Kamaya Kamaya Molex Wisher TYPE BCX 54 BC 848 B BCX 54 BC 848 B BC 848 B BC 858 B MMA 0204-50 MMA 0204-50 5569-06-A1 WKP-N8SG-L Last update 21.04.94 XW0002E4_fm5.f 3 Product: TDM-20-N / OW0002 Power supply 28.1.1999 Component Side Layout PW0002A0 (Schematic OW0002A0) XW0002E4_fm5.f 4 Product: TDM-20-N / OW0002 Power supply 28.1.1999 Solder Side Layout PW0002A0 (Schematic OW0002A0) XW0002E4_fm5.f 5 Product: TDM-20-N / OW0002 Power supply 28.1.1999 XW0002E4_fm5.f 6 Product: TDM-20-N (Forte i) / Audio 28.1.1999 10.0 AUDIO Audio 10.0.1 Principles Of Audio Operation Audio is split into three sections, according to part-numbers: TX-AUDIO Regulator RX-AUDIO parts 200 ... 289 parts 290 ... 299 parts 300 ... 399 10.0.2 TX-Audio I382 works as input buffer and attenuator and band-pass-filter (300 Hz...3.4 kHz). I220 and I384D control the microphone line VOL in VOX mode (range c.20 dB), and function as two-step limiters (c. 1 dB, 3 dB) in normal use. Yhe circuits combine the TXAUXOUT and DTMFTX signals too. I210A act as MICDET AC/DC conventer. I384C act as dynamic compressor which is passed-by I390B. C234 and R234 set a 6 dB pre-emph, and I235A act as amplifier. I235B form a first maximum deviation limiter. I382D form a second limiter and a low-pass-filter with the cut-off frequency of 3.4 kHz. I382E act as the band-pass-filter of FII signal. I210B combines FII and FFSKT signals, which are fed through the TXAUDIO line to the synthesizer. VR is modulated to VFF-voltage for I205C modem connection. 10.0.3 RX-Audio I382 serves as an amplifier for reciever signals, or an attenuator in AUDLOOPON mode. From I382F the FII signal branches to TXAUDIO. In the other branch, I382F filters audio signal (300 Hz...3,4 kHz) and forms a 6 dB de-emph. I384E works as an attenuator to expandor which is passed-by I390C. I321A act as ERPDET AC/DC converter. I361 and I321 together give VOL-control on SPK-line (control range +15...-10 dB), and also combine DTMF signals. The control is also used in VOX mode. VPS is modulated to VDref-half-voltage for I321B. XZ0014E4_fm5.fm 1 Product: TDM-20-N (Forte i) / Audio 28.1.1999 Half-voltage goes also to DTMF switch I305A. I331 and I342A together give VOL-control on ERP-line (control rante +15 dB...-10 dB). I342 is an amplifier for the system-cable. 10.0.4 Regulator I380 regulate 9 V to 5 V (VR). Q295 switch on VPS-voltage to the audio parts. The processor provides 4 MHz clock frequency for the CMOS switched capasitor filter of which parts B, D, E and F are filters and A generates half-voltage Vbias. I384A generates half-voltages Vref and VTref. B part is an expandor, C part is an compressor and D and E parts are amplifiers. 10.0.5 Audio 10.0.5.1 Logic Control MICVOL: 2 TXAUDCONT: 3 - AUXOFF - TXAON - FFSKT - DTMFON ERPVOL: 2 RXAUDCONT: 7 accessory bypass TX audio ON modem ON DTMF ON erp/spk VOL control (0,1,2) RX logic control - FIILOOP - RXAON - ERPON - SPKON - HIDTMFON - COMPOFF - AUDIOPWR ON (FII signal loop ON) audioloop from TX to RX (test) RX-AUDIO ON handset ON speaker ON hi DTMF level ON compandor OFF audio power amplifier ON -DTMFRXON DTMF to speaker ON - AUDILOOP XZ0014E4_fm5.fm microphone VOL-control (0,1,2) TX logic control 2 Product: TDM-20-N (Forte i) / Audio 28.1.1999 10.0.6 Audio Input Signals (ac-values 3 kHz deviation, 1 kHz signal) MIC SO TXAOUT RXAOUT DTMFTX RXAUDIO 4 MHz microphone signal (+PWRSW-signal) modem signal accessory to transmitter accessory to erp/speaker DTMF generator to TX and speaker receiver to audio 4 MHz clock to audio-filter circuit 1 VRMS 775 mVRMS 400 mVRMS 400 mVRMS 150 mVRMS c.120 VRMS 10.0.7 Audio Output Signals (ac-values 3 kHz deviation, 1 kHz signal) MICDET PWRSW TXAUXIN RXAUXIN TXAUDIO ERPDET DTMFRX SPK ERP FFSKR HOOK XZ0014E4_fm5.fm microphone DC-signal level to processor AD converter PWR-switch signal microphone to aux receiver to aux audio to synthesizer receiver DC-signal level to processor AD converter DTMF-signals from receiver to DTMF receiver audio output to speaker (+15...-10 dB) audio output to handset (+15...-10 dB) (+ HOOK-signal) modem signal HOOK-signal from handset 0...8 VDC 5/0 VDC 400 mVRMS 300 mVRMS 550 mVRMS 0...8 VDC 400 mVRMS 120 mVRMS (VOL 0 dB) 300 mVRMS (VOL 0 dB) 400 mVRMS 5/0 mVRMS 3 Product: TDM-20-N (Forte i) / Audio 28.1.1999 10.0.7.1 Operating Voltages In Audio 9V VR VPS VTREF VFF VREF VDREF Vbias supply voltage from OW-module constant voltage in audio (regulated) interrupt voltage in audio (regulated) TX half-voltage DC bias to modem RX half-voltage (interrupted) RX half-voltage (interrupted) RX/TX half-voltage (continuous) 9V 5V 5V 2.5V 1.5V 2.5V 2.5V 2.5V 10.0.8 Audio Settings Measurements must be made with a multimeter of 10 Mohm resistance. AC range of meter should be 20 Hz... 20 kHz. LOCAL-BOX must be used when making adjustments. 10.0.9 Operating Voltages 9V VR Vbias Vref VPS VTref VFF VDref X-PWR I380 I382 I384 I384 I384 I205 I321 pin 2 pin 1 pin 7 pin 8 pin 20 pin 8 pin 9 pin 5 9V 4.8 ... 5.1 V 2.4 ... 2.55 V 2.35 ... 2.5 V 4.7 ... 5.0 V 2.35 ... 2.5 V 1.4 ... 1.6 V 2.35...2.5 V 10.0.10 RX Audio RF-generator settings: - frequency 465.225 MHz - rf-level 60 dBuV - modulation frequency 1 kHz - deviation 3 kHz XZ0014E4_fm5.fm 4 Product: TDM-20-N (Forte i) / Audio 28.1.1999 Local-box switches set to SERVICE and RADIO Set mid-channel (local 36#) By-pass compandor (local 200*, COMPOFF). Turn on RX-audio (local 22# RXA ON , local 200# EXP ON). DO NO TOUCH VOLcontrol during setting operation. RX-audio level is set with 300 mVRMS trimmer R302 (RX) and is measured at the local-box METER-connector. Reset (local 0#). 10.0.11 TX-Audio 10.0.11.1 Normal Deviation: - Local-box switches set to SERVICE and RADIO. - Turn to TX-audio (local 21#, TXA ON). - By-pass compandor (local 200*, COMPOFF) - Feed a 1 kHz, 1 VRMS signal from a AF-generator to the local-box GEN connector. - Connect multimeter to X-SYNTE, pin 2, and adjust trimmer R241 (TX) to show 550 mVRMS. - Switch on transmitter to medium power (LOCAL 32#, M TXON) on midchannel (local 36#, MIDLEC). - Adjust deviation with trimmer R459 (MOD; OS-module) to +/-3 kHz peak. - Drop AF-generator level until deviation is +/-1 kHz and measure comparative level at X-SYNTE, pin 2. - Change AF-generator frequency to 300 Hz. - Raise pt-generator level until meter level showe the previous comparative level. - Adjust the deviation with trimmer R457 (COMP., OS-module) to +/-1 kHz. 10.0.12 Maximum Deviation - Change AF-generator frequency to 1 kHz. - Raise AF-generator level to 3.33 Vrms - Compare channels 0,90 and 180 in turn, and check that max. deviation is +/4.5 kHz. If deviation exceeds 4.5 kHz then adjust with trimmer R244 to max. 4.45 kHz. XZ0014E4_fm5.fm 5 Product: TDM-20-N (Forte i) / Audio 28.1.1999 10.0.13 FFSKT Deviation - Switch to medium power (local 32#, M TXON). - Turn FFSKT on (local 12#, SEND 0). - Adjust deviation with trimmer R265 (FFSKT) to +/-4.2 kHz. - Reset (local 0#). 10.0.14 FII Deviation, Method 1 RF-generator settings: - frequency 465.225 MHz (mid-channel) - RF-level 60 dBuV - modulation frequency 4 kHz - deviation 600 Hz Open FII-LOOP (local 23#, FII ON). Medium-power ON (local 32#, MTXON) Adjust devialtion with trimmer R255 (FII) to +/-670 Hz FII-limits 610...730 Hz Reset (local 0#). 10.0.15 FII Deviation, Method 2 (not recommendable) - Set phone to NMT-mode - Set CMT to mid-channel - Make a call with CMT - Set handset to MUTED-mode - Find "PASS SUP. TONE" from CMT - Set CMT-deviation frequency to 0 Hz - Adjust deviation with trimmer R255 (FII) to +/-650 Hz - FII-limits 590...710 Hz - End call XZ0014E4_fm5.fm 6 Product: TDM-20-N (Forte i) / Audio 28.1.1999 10.0.16 Limiter Adjustment - Local-box switches set to SERVICE and RADIO - Turn on TX-audio (local 21#, TXA ON) - Switch to medium power (local 32#, MTXON) - Feed a 1 kHz, 1 VRMS signal from a AF-generator to the local-box GEN connector - Indicated deviation should be +/-3 kHz - Set to adjust-mode (local 39#, DEV LO) - Raise AF-generator level until deviation reading is +/-3.4 kHz; handset reading should be c. 80...90 (AD-converter value) - Press OK (first limiter-level set to EEPROM memory); "DEV HI" on display - Raise pt-generator level until deviation is +/-4.15 kHz - Press OK (second limiter level stored to EEPROM) - Should the maximum deviation remain below +/-4.15 kHz, set the second limiter level to AD-converter value 145 (display shows DEV HI) - Limiter settings can be checked with local 39*, DEVLIM. 10.0.17 Deviation Limiter There is an SW controlled deviation limiter in the phone. The purpose of the deviation limiter is to compress microphone levels which causes maximum deviation and distortion to transmitted voice. Deviation limiter is tuned during manufacturing. There are two thresholds in the limiter. When microphone signal is above tuned threshold the limiter attenuates it. Attenuation is 0.8 dB when microphone signal is above the first threshold and 2.7 dB when above the second. 10.0.18 Voice Operated HF 10.0.18.1 General: Voice operated HF software uses microphone and speaker level detectors to measure, and TX and RX attenuators to set the microphone and speaker signals. Voice operated HF is designed in such a way that a detected microphone signal above tuned HF threshold always attenuates the speaker signal. Microphone threshold is tuned in LOCAL by installer to work properly in the vehicle where the phone is used. XZ0014E4_fm5.fm 7 Product: TDM-20-N (Forte i) / Audio 28.1.1999 10.0.18.2 Seesaw Model Of The Voice Operated HF 1. When microphone signal rises above tuned threshold the TX attenuation is decreased and RX attenuation is increased. Note: The deviation limiter may work which causes some TX attenuation. 2. When microphone signal drops below tuned threshold TX attenuation is increased and RX attenuation is decreased. Note: The actual RX attenuation minimum depends on user preset speaker volume level. 3. When there are simultaneous speaker and microphone signals HF is set in duplex state where TX and RX attenuators are in middle positions. Note: The actual RX attenuation depends on user preset speaker volume level. 10.1 Processor Functions All audio and processor functions of the radio are located on the same PCB; other modules are interconnected through it. Only the RF-signals have a different route. The processor controls the audio and radio units and the handset. 10.1.1 The Processor Includes CPU PROM XZ0014E4_fm5.fm RAM 68HC11 27C512 44658K*8 CMOS RAM MODEM FX439 I/O DTMFTX DTMFRX TXLOG PCD3312 MV8870 8-bit, 8 A/D, 512*8 EEPROM, I/O 64K*8 EPROM, program memory program space and short-code memory 1200bd FFSK modem, radio path signalling 33 pcs outputs and 18 pcs inputs DTMF generator and tone signals DTMF receiver TX power adjustment and control 8 Product: TDM-20-N (Forte i) / Audio 28.1.1999 10.1.2 Connectors: 10.1.2.1 Handset: XBUS 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 GND MICF AGND AUTOCALLF EXTALF ground audio signal from microphone audio ground 1 VRMS activates the autocall function 12 V I2cINTF SDAXF +9VF ERPF RXFIXF PTTF i2c interrupt from handset, 0-active i2c dataline, duplex +9 V voltage to handset audio earphone (VOL 0dB) .5 A .4 VRMS SCLXF i2c clock to handset push to talk, exterior switch to ground 0/5 V 10.1.2.2 Regulator: X-PWR XZ0014E4_fm5.fm 1 2 3 VB +9V VBAT 4 5 6 7 8 RELAY SPK IGN EXTAL EXTMUTE 12 V operating voltage via relay 9 V operating voltage continuous power supply for maintaining RAM standby current relay control, PWR on audio signal to speaker amplifier activates IGN function external alarm control, 5 V activates car radio muting 5 V activates 5 A max 1 A max 5V 120 mV 12 V 9 Product: TDM-20-N (Forte i) / Audio 28.1.1999 10.1.2.3 Synthesizer: X-SYNTE 1 2 3 4 5 6 7 8 VB TXAUDIO GND SRE STE SCLK SDATA TXVCO synthesizer 12 V operating voltage tx audio modulation ground enable pulse for rx scaler enable pulse for tx scaler clock for rx and tx data rx and tx data for scalers tx for vco ON 550 mV 5V 5V 0/5 V 0/5 V 5V 10.1.2.4 Receiver: X-RX 1 2 3 4 +9V RSSI RXAUDIO GND operating voltage to receiver rx signal strength indicator, analog rx audio signal ground 9V 0...5 V 100...150 mV tx power sensing, analog 0...10 V tx power control, analog 0...9 V 10.1.2.5 Transmitter: X-TX 1 2 3 4 XZ0014E4_fm5.fm TXSENSE TXPWRCTR TXBIAS tx bias 9 V 50 mA, Ov= tx off 10 Product: TDM-20-N (Forte i) / Audio 28.1.1999 10.1.2.6 Accessory: X-E1 1 2 3 4 5 6 7 8 9 10 TXAIN TXAOUT GND RXAIN RXAOUT VB I2cINT EXTi2cE N SDA SCL operating voltage i2c interrupt, 0 active 12 V enable to accessory’s i2c bus 5V i2c data i2c clock 0/5 V 0/5 V - Power switch connected to mic line, grounds the mic line. - Hook switch connected to erp line, dropping the dc level of the handset erp line while the handset is on the holder. 10.1.3 Circuit Diagram The circuit diagram of the processor is divided into six parts. The first figure shows the connector interfaces and the division between audio and processor. The orther five figures illustrate the subfunctions. Audio is shown in three drawings. In the diagrams, the signals have been given names so that identical names are connected between drawings. The circuit includes: OACONN CPU MEM IO TXLOG AUDIO RXAUDIO TXAUDIO SIS figure of PCB connectors (sheet 1 of 9) cpu, memory coding and modem (sheet 5 of 9) memory (RAM, EPROM), supply input and start-up(sheet 7 of 9) input and output gates, DTMF rx and tx (sheet 6 of 9) TX control logic (sheet 8 of 9) audio power supply and block diagrams (sheet 2 of 9) receiver audio parts (sheet 3 of 9) transmitter audio parts (sheet 4 of 9) sis function (sheet 9 of 9) 10.1.3.1 Component Numbering The components on each module are numbered unambiguously. Each component number is only shown in one place. The processor has the numbers between 001 and 199, and the audio between 200 and 399. XZ0014E4_fm5.fm 11 Product: TDM-20-N (Forte i) / Audio 28.1.1999 10.1.3.2 Functions The I050 is the processor circuit. It includes the CPU, the 512*8bit EEPROM, timers A/D converters and serial and parallel I/O lines. The X052 is an 8 MHz clock oscillator; diving this by a factor of 4 gives timing signal E. While the processor is working, RESET is 5 V, VCC is 5 V, E is 2MHz; AS, R/W, and AO...A15 pulses must change between 0 and 5 V. The address codes for memory circuits and external I/O-circuits are made with I103...I107. The chipselects CSR, CSP and CSIO are 0-active. The FFSK modem I065 has its own clock X065 4.032 MHz. The modem is connected to CPU by serial lines, reception is connected to the syncron gate, and transmission is controlled by IRQ-interrupt. The modem gives 1200 Hz clock pulses RXCLK and TXCLK to the processor. The data detector is located in the modem, and its speed is determined by C070 and C073. The 4 MHz clock required by the audio circuit is obtained by dividing the CPU clocksignal with I062. C040 and R040 sense the length of voltage break, the voltage drops during the break, after which the voltage is measured with an A/D converter. The time constant is approx. 10 seconds. The program memory is in 64k*8 EPROM and it uses the addresses 4000H...FFFFH. The RAM memory is in 8k*8 CMOS RAM using addresses 0000H...1FFFH. The power supply to RAM has three different paths: in normal use through D133, when the radio is OFF, the D135 regulates the voltage, and when the battery power is disconnected, the RAM gets its supply from A135 (3 V lithium battery). Voltage control circuit Q128, Q130, and D126 stops the processor, and resets the control functions when the supply voltage drops below 7 V. When the voltage exceeds 8 V, the processor is restarted. The power supply switch logic I118 is also connected to RAM supply in order to maintain proper RAM functions when the radio is off. The power switch (PWRSW) is ground-connected, and activates the current relay while pressed. The program starts and checks the PWRSWS line to ensure that the button is pressed and sets the current relay to hold mode on the PWRCTRL line. If the power switch is pressed a long time, the program trips to the PWROFF line. The C1231 and R123 maintains stored control during a short voltage break, i.e the relay becomes active again when the voltage comes back within 10 seconds. It also works as a control circuit in case of prolonged voltage-drop or processor malfunction and after 10 seconds the radio will switch off. XZ0014E4_fm5.fm 12 Product: TDM-20-N (Forte i) / Audio 28.1.1999 While the IGN line is connected, the radio is switched on when IGN rises to 12 V. The radio is switched off by the mains switch or by the handset-programmable timer (0...99 h) when IGN goes to 0. The buffers of the i2c path (to the handset) are Q138, Q139 and I094C,D. The external (outside CPU) I/O gates I090...I094are 8-bit addressable latches. DATA is sent ot the output determined by three address lines. When the RESET line goes down, it closes all outputs down too. The input circuit I096 works correspondingly, except that there are inputs instead of outputs. The DTMF receiver I097 gives an StD pulse at the beginning of the tone and the data is then in lines Q0...Q3. The StD closes down when the tone signal finishes. The DTMF generator I099 is I2c bus controlled. It forms DTMF tones and all radio tone signals. The crystal X099works as a common clock for both DTMF circuits and it is controlled by the program. The transmitter control logic sets the TX power to the right level and turns the power off. The TXVCO signal sets the transmitter to standby mode (bias on), the TX0 and TX1 set the power levels and the TXON turns the power on and off. XZ0014E4_fm5.fm TXVCO TX0 TX1 TXON 0 x x x tx off 1 x x 0 tx standby, no power 1 0 0 1 low tx power 1 0 1 1 medium tx power 1 1 0 1 high tx power 13 Product: TDM-20-N (Forte i) / Audio 28.1.1999 Component Side Layout PA0014A0 (Schematic OA0014A-I2) XZ0014E4_fm5.fm 14 Product: TDM-20-N (Forte i) / Audio 28.1.1999 Solder Side Layout PA0014A0 (Schematic OA0014A-I2) XZ0014E4_fm5.fm 15 Product: TDM-20-N (Forte i) / 28.1.1999 10.1.4 Parts list CODE PART DESCRIPT. VALUE MANUF. TYPE AB0003 CD0471 CD0471 CD0471 CD0471 CD0471 CD0471 CD0471 CD0471 CD0471 CD0471 CD0102 CD0223 CD0223 CD0223 CD0223 CD0223 CD0223 CU0106 CD0223 CD0223 CD0220 CD0220 CD0223 CD0223 CD0330 CD0330 CU0105 CC0473 CU0105 CD0223 CC0473 CD0223 CD0223 CD0223 CC0473 CD0223 CU0105 CD0100 CC0473 CD0223 CD0223 CD0223 CD0223 CD0223 CD0223 CD0223 CU0105 CD0223 CU0106 CE0107 CU0106 CD0223 CU0106 CD0223 CD0223 CD0331 A134 C001 C003 C004 C005 C006 C007 C009 C010 C011 C012 C030 C032 C034 C035 C036 C038 C039 C040 C046 C049 C052 C053 C055 C062 C065 C066 C068 C070 C071 C072 C073 C075 C077 C090 C091 C092 C093 C094 C096 C097 C098 C099 C100 C101 C103 C107 C115 C118 C123 C125 C132 C133 C134 C153 C160 C162 Lithium battery SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD tantal SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD tantal SMD capasitor SMD tantal SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD tantal SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD tantal SMD capasitor SMD tantal Al elko SMD tantal SMD capasitor SMD tantal SMD capasitor SMD capasitor SMD capasitor 3V 180mAh d=20mm 470 pF 5% 50 V NP0 470 pF 5% 50 V NP0 470 pF 5% 50 V NP0 470 pF 5% 50 V NP0 470 pF 5% 50 V NP0 470 pF 5% 50 V NP0 470 pF 5% 50 V NP0 470 pF 5% 50 V NP0 470 pF 5% 50 V NP0 470 pF 5% 50 V NP0 1 nF 5 % NP0 22 nF 10% 50 V X7R 22 nF 10% 50 V X7R 22 nF 10% 50 V X7R 22 nF 10% 50 V X7R 22 nF 10% 50 V X7R 22 nF 10% 50 V X7R 10uF/16V 20% 6x3.2mm 22 nF 10% 50 V X7R 22 nF 10% 50 V X7R 22 pF 5% 50 V NP0 22 pF 5% 50 V NP0 22 nF 10% 50 V X7R 22 nF 10% 50 V X7R 33 pF 5% 50 V NP0 33 pF 5% 50 V NP0 1uF/16V 20% 3.2x1.6mm 47 nF 10% 50 V X7R 1uF/16V 20% 3.2x1.6mm 22 nF 10% 50 V X7R 47 nF 10% 50 V X7R 22 nF 10% 50 V X7R 22 nF 10% 50 V X7R 22 nF 10% 50 V X7R 47 nF 10% 50 V X7R 22 nF 10% 50 V X7R 1uF/16V 20% 3.2x1.6mm 10 pF/0.25pF 50 V NP0 47 nF 10% 50 V X7R 22 nF 10% 50 V X7R 22 nF 10% 50 V X7R 22 nF 10% 50 V X7R 22 nF 10% 50 V X7R 22 nF 10% 50 V X7R 22 nF 10% 50 V X7R 22 nF 10% 50 V X7R 1uF/16V 20% 3.2x1.6mm 22 nF 10% 50 V X7R 10uF/16V 20% 6x3.2mm 100uF 16V 7x7mm 10uF/16V 20% 6x3.2mm 22 nF 10% 50 V X7R 10uF/16V 20% 6x3.2mm 22 nF 10% 50 V X7R 22 nF 10% 50 V X7R 330 pF 5% 50 V NP0 Matsushita Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Matsushita Philips Philips Philips Philips Philips Philips Philips Philips Matsushita Philips Matsushita Philips Philips Philips Philips Philips Philips Philips Matsushita Philips Philips Philips Philips Philips Philips Philips Philips Philips Matsushita Philips Matsushita Philips Matsushita Philips Matsushita Philips Philips Philips BR2032-1HG XA0014E4_FM5.f ECST1CC 106R ECST1CY 105R ECST1CY 105R ECST1CY 105R ECST1CY 105R ECST1CC 106R 2222 097 55101 ECST1CC 106R ECST1CC 106R 16 Product: TDM-20-N (Forte i) / 28.1.1999 CODE CC0222 CD0223 CC0473 CD0102 CD0330 CD0103 CD0103 CU0105 CD0330 CD0102 CD0103 CU0105 CU0105 CC0222 CD0330 CU0225 CC0473 CD0100 CD0223 CD0101 CC0473 CC0102 CC0102 CD0471 CC0102 CC0102 CC0222 CD0221 CU0105 CU0105 CD0223 CU0106 CD0223 CE0107 CU0105 CD0223 CE0107 CD0472 CC0473 CD0330 CC0473 CD0223 CC0473 CD0221 CU0225 CD0103 CD0223 CU0105 CD0223 CD0101 CC0473 CD0101 CP0474 CU0105 CD0223 CD0472 CD0101 CU0225 CD0223 CU0106 PART C165 C180 C200 C202 C203 C204 C210 C216 C227 C229 C230 C232 C233 C234 C235 C236 C237 C238 C242 C243 C247 C252 C253 C257 C262 C263 C267 C270 C275 C278 C290 C291 C292 C293 C295 C296 C297 C300 C301 C305 C306 C307 C308 C312 C314 C320 C321 C326 C332 C339 C341 C342 C345 C348 C353 C355 C369 C370 C382 C383 XA0014E4_FM5.f DESCRIPT. SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD tantal SMD capasitor SMD capasitor SMD capasitor SMD tantal SMD tantal SMD capasitor SMD capasitor SMD tantal SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD tantal SMD tantal SMD capasitor SMD tantal SMD capasitor Al elko SMD tantal SMD capasitor Al elko SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD tantal SMD capasitor SMD capasitor SMD tantal SMD capasitor SMD capasitor SMD capasitor SMD capasitor Polyester cap SMD tantal SMD capasitor SMD capasitor SMD capasitor SMD tantal SMD capasitor SMD tantal VALUE 2.2 nF 5% 50 V NP0 22 nF 10% 50 V X7R 47 nF 10% 50 V X7R 1 nF 5 % NP0 33 pF 5% 50 V NP0 10 nF 10% 50 V X7R 10 nF 10% 50 V X7R 1uF/16V 20% 3.2x1.6mm 33 pF 5% 50 V NP0 1 nF 5 % NP0 10 nF 10% 50 V X7R 1uF/16V 20% 3.2x1.6mm 1uF/16V 20% 3.2x1.6mm 2.2 nF 5% 50 V NP0 33 pF 5% 50 V NP0 2.2uF/16V 20% 4.7x2.6mm 47 nF 10% 50 V X7R 10 pF/0.25pF 50 V NP0 22 nF 10% 50 V X7R 100 pF 5% 50 V NP0 47 nF 10% 50 V X7R 1 nF 5% 50V NP0 1 nF 5% 50V NP0 470 pF 5% 50 V NP0 1 nF 5% 50V NP0 1 nF 5% 50V NP0 2.2 nF 5% 50 V NP0 220 pF 5% 50 V NP0 1uF/16V 20% 3.2x1.6mm 1uF/16V 20% 3.2x1.6mm 22 nF 10% 50 V X7R 10uF/16V 20% 6x3.2mm 22 nF 10% 50 V X7R 100uF 16V 7x7mm 1uF/16V 20% 3.2x1.6mm 22 nF 10% 50 V X7R 100uF 16V 7x7mm 4.7 nF 10% 50 V X7R 47 nF 10% 50 V X7R 33 pF 5% 50 V NP0 47 nF 10% 50 V X7R 22 nF 10% 50 V X7R 47 nF 10% 50 V X7R 220 pF 5% 50 V NP0 2.2uF/16V 20% 4.7x2.6mm 10 nF 10% 50 V X7R 22 nF 10% 50 V X7R 1uF/16V 20% 3.2x1.6mm 22 nF 10% 50 V X7R 100 pF 5% 50 V NP0 47 nF 10% 50 V X7R 100 pF 5% 50 V NP0 470nF 63V 10% 1uF/16V 20% 3.2x1.6mm 22 nF 10% 50 V X7R 4.7 nF 10% 50 V X7R 100 pF 5% 50 V NP0 2.2uF/16V 20% 4.7x2.6mm 22 nF 10% 50 V X7R 10uF/16V 20% 6x3.2mm MANUF. Philips Philips Philips Philips Philips Philips Philips Matsushita Philips Philips Philips Matsushita Matsushita Philips Philips Matsushita Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Matsushita Matsushita Philips Matsushita Philips Philips Matsushita Philips Philips Philips Philips Philips Philips Philips Philips Philips Matsushita Philips Philips Matsushita Philips Philips Philips Philips Evox Matsushita Philips Philips Philips Matsushita Philips Matsushita TYPE ECST1CY 105R ECST1CY 105R ECST1CY 105R ECST1CB 225R ECST1CY 105R ECST1CY 105R ECST1CC 106R 2222 097 55101 ECST1CY 105R 2222 097 55101 ECST1CB 225R ECST1CY 105R ECST1CY 105R ECST1CB 225R ECST1CC 106R 17 Product: TDM-20-N (Forte i) / 28.1.1999 CODE CD0223 CE0107 CD0223 CD0223 DS0070 DS0070 DS0070 DS0070 DS0070 DZ0759 DS0070 DS0070 DZ0569 DS0099 DS0099 DS0099 DS0099 IP6811 IH0373 IH0004 IH0074 IX0439 IA0272 IH0259 IH0259 IH0259 IH0259 IH0032 IH0251 IA8870 II3312 IM7512 IM3664 IH4002 IH4078 IH0004 IH0000 IH0010 IH0132 IR2952 IA0272 IP6831 IH4066 IA0272 IH4051 IA0272 IH4066 IA0272 IH4066 IH4051 IA3182 IH4051 IR2952 IX0346 IX0575 IH4053 LC0105 LC0105 LC0105 LF0396 PART C384 C385 C387 C390 D032 D076 D094 D120 D125 D126 D133 D134 D135 D200 D214 D324 D345 I050 I055 I060\ I062\ I065 I075\ I090 I091 I092 I093 I094\ I096 I097 I099 I100 I101 I103\ I104 I105\ I106\ I107\ I118\ I132 I160\ I180 I205\ I210\ I220 I235\ I305\ I321\ I330\ I331 I342\ I361 I380 I382\ I384\ I390\ L001 L003 L004 L005 XA0014E4_FM5.f DESCRIPT. SMD capasitor Al elko SMD capasitor SMD capasitor SMD diode pair SMD diode pair SMD diode pair SMD diode pair SMD diode pair SMD zener SMD diode pair SMD diode pair SMD zener SMD diode SMD diode SMD diode SMD diode 8-BIT MIKROPROS 3-st.octal latch Hex inverter 2xD-flip-flop FFSK modem 2 x op.amp. 8-bit addr latch 8-bit addr latch 8-bit addr latch 8-bit addr latch 4x2-inp OR 8-inp multipl. 3-state DTMF decoder DTMF generator One time prom CMOS 8K*8 CMOS RAM 2x4-inp NOR 1x8-inp OR/NOR Hex inverter 4x2-inp NAND 3x3-inp. NAND 4x2 inp NAND schm. Regulator 2 x op.amp. Processor (SIS) 4xbilateral switch 2 x op.amp. 8-ch anal.multipl. 2 x op.amp. 4xbilateral switch 2 x op.amp. 4xbilateral switch 8-ch anal.multipl. 2xop.amp. 8-ch anal.multipl. Regulator Audio filter array Rx/Tx Compander 3x2-ch analog mpxer SMD inductor SMD inductor SMD inductor Inductor VALUE 22 nF 10% 50 V X7R 100uF 16V 7x7mm 22 nF 10% 50 V X7R 22 nF 10% 50 V X7R 70V/100mA common cathode 70V/100mA common cathode 70V/100mA common cathode 70V/100mA common cathode 70V/100mA common cathode 7V5 5% 300mW 70V/100mA common cathode 70V/100mA common cathode 5V6 5% 300mW 70 V 200 mA 70 V 200 mA 70 V 200 mA 70 V 200 mA 512 EEPROM, 8A/D, no ROM HCMOS HCMOS HCMOS 1200 baud CMOS LinCMOS Low noise,power HCMOS HCMOS HCMOS HCMOS HCMOS HCMOS I2C 65.536 x 8b 200ns F28GA-P 11.8mm width HCMOS HCMOS HCMOS HCMOS HCMOS HCMOS 100mA 5V adj. 0.5% LinCMOS Low noise,power 8k maskPROM,512EEPROM HCMOS LinCMOS Low noise,power HCMOS LinCMOS Low noise,power HCMOS LinCMOS Low noise,power HCMOS HCMOS Low power,jfet input HCMOS 100mA 5V adj. 0.5% CMOS HCMOS 1.0 uH 1.0 uH 1.0 uH 39 uH MANUF. Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Motorola RCA RCA RCA CML Texas RCA RCA RCA RCA RCA RCA Plessey Philips Fujitsu Toshiba RCA RCA RCA Micrel Texas Motorola RCA Texas RCA Texas RCA Texas RCA RCA Motorola RCA Micrel CML Philips RCA Siemens Siemens Siemens Philips TYPE 2222 097 55101 BAV 70 BAV 70 BAV 70 BAV 70 BAV 70 BZX84C7V5 BAV 70 BAV 70 BZX84C5V6 BAV 99 BAV 99 BAV 99 BAV 99 MC68HC11A1FN 74HC373 74HC04 74HC74 FX439LG TLC27M2ID 74HC259 74HC259 74HC259 74HC259 74HC32 74HC251 MV8870 PCD3312T MBM27C512P-20P TC5565AFL-15L 74HC4002 74HC4078 74HC04 74HC00 74HC10 74HC132 MIC2951-02BM TLC27M2ID MC68HC11A8 FU 74HC4066B TLC27M2ID 74HC4051B TLC27M2ID 74HC4066B TLC27M2ID 74HC4066B 74HC4051B MC 33182D 74HC4051B MIC2951-02BM FX346GL SA575 74HC4053 B82412-A1102-M B82412-A1102-M B82412-A1102-M 18 Product: TDM-20-N (Forte i) / 28.1.1999 CODE LC0105 LC0105 LC0105 LC0105 LC0105 LC0105 PA0014 QSB848 QSB848 QSB848 QSB848 QSB848 QSB848 QSB848 QSB858 QSB848 QSB858 QSB848 QSB848 QSB848 QSB848 QSB858 QSB848 RD0103 RD0104 RD0103 RC0000 RD0104 RD0104 RD0104 RD0104 RD0104 RD0104 RD0105 RD0104 RD0105 RD0104 RD0103 RD0103 RD0104 RD0103 RD0104 RD0103 RD0105 RD0104 RD0104 RD0103 RD0103 RD0105 RD0334 RD0222 RD0333 RD0684 RD0104 RD0101 RD0104 RD0104 RD0474 RD0103 RD0474 PART L006 L007 L009 L010 L011 L012 PCB Q063 Q114 Q122 Q128 Q130 Q131 Q138 Q139 Q151 Q153 Q159 Q165 Q168 Q169 Q295 Q375 R011 R015 R020 R022 R030 R031 R032 R034 R035 R036 R038 R039 R040 R042 R043 R045 R046 R048 R049 R050 R052 R060 R061 R063 R064 R065 R073 R074 R075 R076 R077 R078 R091 R092 R093 R094 R096 XA0014E4_FM5.f DESCRIPT. SMD inductor SMD inductor SMD inductor SMD inductor SMD inductor SMD inductor PCB for OA0014 SMD transistor SMD transistor SMD transistor SMD transistor SMD transistor SMD transistor SMD transistor SMD transistor SMD transistor SMD transistor SMD transistor SMD transistor SMD transistor SMD transistor SMD transistor SMD transistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor VALUE 1.0 uH 1.0 uH 1.0 uH 1.0 uH 1.0 uH 1.0 uH Forte 450 I NPN 0.1A/30V F=2dB NPN 0.1A/30V F=2dB NPN 0.1A/30V F=2dB NPN 0.1A/30V F=2dB NPN 0.1A/30V F=2dB NPN 0.1A/30V F=2dB NPN 0.1A/30V F=2dB PNP 0.1A/30V F<10dB NPN 0.1A/30V F=2dB PNP 0.1A/30V F<10dB NPN 0.1A/30V F=2dB NPN 0.1A/30V F=2dB NPN 0.1A/30V F=2dB NPN 0.1A/30V F=2dB PNP 0.1A/30V F<10dB NPN 0.1A/30V F=2dB 10 k 5% 0.125 W 100 k 5% 0.125 W 10 k 5% 0.125 W 0R 100 k 5% 0.125 W 100 k 5% 0.125 W 100 k 5% 0.125 W 100 k 5% 0.125 W 100 k 5% 0.125 W 100 k 5% 0.125 W 1 M 5% 0.125 W 100 k 5% 0.125 W 1 M 5% 0.125 W 100 k 5% 0.125 W 10 k 5% 0.125 W 10 k 5% 0.125 W 100 k 5% 0.125 W 10 k 5% 0.125 W 100 k 5% 0.125 W 10 k 5% 0.125 W 1 M 5% 0.125 W 100 k 5% 0.125 W 100 k 5% 0.125 W 10 k 5% 0.125 W 10 k 5% 0.125 W 1 M 5% 0.125 W 330 k 5% 0.125 W 2.2 k 5% 0.125 W 33 k 5% 0.125 W 680 k 5% 0.125 W 100 k 5% 0.125 W 100 R 5% 0.125 W 100 k 5% 0.125 W 100 k 5% 0.125 W 470 k 5% 0.125 W 10 k 5% 0.125 W 470 k 5% 0.125 W MANUF. Siemens Siemens Siemens Siemens Siemens Siemens Aspocomp Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya TYPE B82412-A1102-M B82412-A1102-M B82412-A1102-M B82412-A1102-M B82412-A1102-M B82412-A1102-M BC 848 B BC 848 B BC 848 B BC 848 B BC 848 B BC 848 B BC 848 B BC 858 B BC 848 B BC 858 B BC 848 B BC 848 B BC 848 B BC 848 B BC 858 B BC 848 B 19 Product: TDM-20-N (Forte i) / 28.1.1999 CODE RD0104 RD0104 RD0104 RD0104 RD0104 RD0103 RD0104 RD0105 RD0104 RD0104 RD0104 RD0105 RD0104 RD0223 RD0223 RD0223 RD0223 RD0223 RD0474 RD0223 RD0223 RD0223 RD0101 RD0103 RD0104 RD0103 RD0103 RD0101 RD0101 RD0104 RD0223 RD0103 RD0101 RM1003 RM1003 RM4643 RD0223 RM3922 RD0224 RI0103 RM4752 RD0223 RM1783 RD0103 RD0223 RD0223 RD0223 RD0104 RD0103 RD0103 RD0103 RD0103 RM3922 RM1002 RM2003 RM3013 RM1623 RM3012 RM2213 RM6813 PART R097 R098 R110 R111 R112 R113 R114 R115 R117 R118 R119 R120 R122 R123 R124 R126 R127 R128 R129 R130 R131 R132 R134 R135 R137 R138 R140 R141 R142 R150 R151 R152 R153 R155 R156 R157 R158 R159 R161 R162 R163 R164 R165 R166 R167 R168 R169 R181 R182 R183 R184 R185 R200 R202 R203 R205 R206 R210 R211 R212 XA0014E4_FM5.f DESCRIPT. SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor Mini-Melf resistor Mini-Melf resistor Mini-Melf resistor SMD resistor Mini-Melf resistor SMD resistor SMD trimmer resistor Mini-Melf resistor SMD resistor Mini-Melf resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor Mini-Melf resistor Mini-Melf resistor Mini-Melf resistor Mini-Melf resistor Mini-Melf resistor Mini-Melf resistor Mini-Melf resistor Mini-Melf resistor VALUE 100 k 5% 0.125 W 100 k 5% 0.125 W 100 k 5% 0.125 W 100 k 5% 0.125 W 100 k 5% 0.125 W 10 k 5% 0.125 W 100 k 5% 0.125 W 1 M 5% 0.125 W 100 k 5% 0.125 W 100 k 5% 0.125 W 100 k 5% 0.125 W 1 M 5% 0.125 W 100 k 5% 0.125 W 22 k 5% 0.125 W 22 k 5% 0.125 W 22 k 5% 0.125 W 22 k 5% 0.125 W 22 k 5% 0.125 W 470 k 5% 0.125 W 22 k 5% 0.125 W 22 k 5% 0.125 W 22 k 5% 0.125 W 100 R 5% 0.125 W 10 k 5% 0.125 W 100 k 5% 0.125 W 10 k 5% 0.125 W 10 k 5% 0.125 W 100 R 5% 0.125 W 100 R 5% 0.125 W 100 k 5% 0.125 W 22 k 5% 0.125 W 10 k 5% 0.125 W 100 R 5% 0.125 W 100k 1% 0.25W 100k 1% 0.25W 464k 1% 0.25W 22 k 5% 0.125 W 39k2 1% 0.25W 220 k 5% 0.125 W 10k 20% 0.25 W 47k5 1% 0.25W 22 k 5% 0.125 W 178k 1% 0.25W 10 k 5% 0.125 W 22 k 5% 0.125 W 22 k 5% 0.125 W 22 k 5% 0.125 W 100 k 5% 0.125 W 10 k 5% 0.125 W 10 k 5% 0.125 W 10 k 5% 0.125 W 10 k 5% 0.125 W 39k2 1% 0.25W 10k0 1% 0.25W 200k 1% 0.25W 301k 1% 0.25W 162k 1% 0.25W 30k1 1% 0.25W 221k 1% 0.25W 681k 1% 0.25W MANUF. Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Beyschlag Beyschlag Beyschlag Kamaya Beyschlag Kamaya Copal Beyschlag Kamaya Beyschlag Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Beyschlag Beyschlag Beyschlag Beyschlag Beyschlag Beyschlag Beychlag Beyschlag TYPE MMA 0204-50 MMA 0204-50 MMA 0204-50 MMA 0204-50 ST-4A MMA 0204-50 MMA 0204-50 MMA 0204-50 MMA 0204-50 MMA 0204-50 BL MMA 0204-50 MMA 0204-50 MMA 0204-50 MMA 0204-50 MMA 0204-50 20 Product: TDM-20-N (Forte i) / 28.1.1999 CODE RD0222 RM3012 RM4752 RM7502 RM1003 RM1623 RM2213 RM2373 RM3013 RM1004 RM1004 RM3012 RM3012 RM1002 RM1623 RM5112 RM3323 RM6491 RD0104 RI0503 RM1783 RI0503 RM2002 RM4752 RM2002 RM2002 RM1623 RI0503 RM3012 RM2743 RD0104 RM1002 RM1002 RI0503 RM1002 RD0683 RD0103 RD0104 RD0104 RM1003 RM4752 RD0473 RD0103 RM3013 RD0224 RI0503 RM4752 RM2743 RM3922 RM1783 RM3922 RD0224 RM1183 RM1003 RM1004 RD0222 RM1623 RM1502 RM2002 RM3012 PART R213 R220 R221 R222 R223 R224 R225 R226 R227 R229 R230 R232 R233 R234 R235 R237 R238 R239 R240 R241 R242 R244 R245 R247 R250 R252 R253 R255 R256 R257 R260 R262 R263 R265 R267 R270 R271 R274 R275 R277 R278 R294 R295 R300 R301 R302 R304 R305 R309 R310 R312 R318 R320 R321 R322 R324 R330 R332 R333 R334 XA0014E4_FM5.f DESCRIPT. SMD resistor Mini-Melf resistor Mini-Melf resistor Mini-Melf resistor Mini-Melf resistor Mini-Melf resistor Mini-Melf resistor Mini-Melf resistor Mini-Melf resistor Mini-Melf resistor Mini-Melf resistor Mini-Melf resistor Mini-Melf resistor Mini-Melf resistor Mini-Melf resistor Mini-Melf resistor Mini-Melf resistor Mini-Melf resistor SMD resistor SMD trimmer resistor Mini-Melf resistor SMD trimmer resistor Mini-Melf resistor Mini-Melf resistor Mini-Melf resistor Mini-Melf resistor Mini-Melf resistor SMD trimmer resistor Mini-Melf resistor Mini-Melf resistor SMD resistor Mini-Melf resistor Mini-Melf resistor SMD trimmer resistor Mini-Melf resistor SMD resistor SMD resistor SMD resistor SMD resistor Mini-Melf resistor Mini-Melf resistor SMD resistor SMD resistor Mini-Melf resistor SMD resistor SMD trimmer resistor Mini-Melf resistor Mini-Melf resistor Mini-Melf resistor Mini-Melf resistor Mini-Melf resistor SMD resistor Mini-Melf resistor Mini-Melf resistor Mini-Melf resistor SMD resistor Mini-Melf resistor Mini-Melf resistor Mini-Melf resistor Mini-Melf resistor VALUE 2.2 k 5% 0.125 W 30k1 1% 0.25W 47k5 1% 0.25W 75k0 1% 0.25W 100k 1% 0.25W 162k 1% 0.25W 221k 1% 0.25W 237k 1% 0.25W 301k 1% 0.25W 1.0M 1% 0.25W 1.0M 1% 0.25W 30k1 1% 0.25W 30k1 1% 0.25W 10k0 1% 0.25W 162k 1% 0.25W 51k1 1% 0.25W 332k 1% 0.25W 6k49 1% 0.25W 100 k 5% 0.125 W 50k 20% 0.25 W 178k 1% 0.25W 50k 20% 0.25 W 20k0 1% 0.25W 47k5 1% 0.25W 20k0 1% 0.25W 20k0 1% 0.25W 162k 1% 0.25W 50k 20% 0.25 W 30k1 1% 0.25W 274k 1% 0.25W 100 k 5% 0.125 W 10k0 1% 0.25W 10k0 1% 0.25W 50k 20% 0.25 W 10k0 1% 0.25W 68 k 5% 0.125 W 10 k 5% 0.125 W 100 k 5% 0.125 W 100 k 5% 0.125 W 100k 1% 0.25W 47k5 1% 0.25W 47 k 5% 0.125 W 10 k 5% 0.125 W 301k 1% 0.25W 220 k 5% 0.125 W 50k 20% 0.25 W 47k5 1% 0.25W 274k 1% 0.25W 39k2 1% 0.25W 178k 1% 0.25W 39k2 1% 0.25W 220 k 5% 0.125 W 118k 1% 0.25W 100k 1% 0.25W 1.0M 1% 0.25W 2.2 k 5% 0.125 W 162k 1% 0.25W 15k0 1% 0.25W 20k0 1% 0.25W 30k1 1% 0.25W MANUF. Kamaya Beyschlag Beyschlag Beyschlag Beyschlag Beyschlag Beychlag Beyschlag Beyschlag Beyschlag Beyschlag Beyschlag Beyschlag Beyschlag Beyschlag Beyschlag Beyschlag Beyschlag Kamaya Copal Beyschlag Copal Beyschlag Beyschlag Beyschlag Beyschlag Beyschlag Copal Beyschlag Beyschlag Kamaya Beyschlag Beyschlag Copal Beyschlag Kamaya Kamaya Kamaya Kamaya Beyschlag Beyschlag Kamaya Kamaya Beyschlag Kamaya Copal Beyschlag Beyschlag Beyschlag Beyschlag Beyschlag Kamaya Beyschlag Beyschlag Beyschlag Kamaya Beyschlag Beyschlag Beyschlag Beyschlag TYPE MMA 0204-50 MMA 0204-50 MMA 0204-50 MMA 0204-50 MMA 0204-50 MMA 0204-50 MMA 0204-50 BL MMA 0204-50 MMA 0204-50 MMA 0204-50 MMA 0204-50 MMA 0204-50 MMA 0204-50 MMA 0204-50 MMA 0204-50 MMA 0204-50 MMA 0204-50 ST-4A MMA 0204-50 ST-4A MMA 0204-50 MMA 0204-50 MMA 0204-50 MMA 0204-50 MMA 0204-50 ST-4A MMA 0204-50 MMA 0204-50 MMA 0204-50 MMA 0204-50 ST-4A MMA 0204-50 MMA 0204-50 MMA 0204-50 MMA 0204-50 ST-4A MMA 0204-50 MMA 0204-50 MMA 0204-50 MMA 0204-50 MMA 0204-50 MMA 0204-50 MMA 0204-50 MMA 0204-50 MMA 0204-50 MMA 0204-50 MMA 0204-50 MMA 0204-50 21 Product: TDM-20-N (Forte i) / 28.1.1999 CODE RM3922 RM4752 RM5622 RM6492 RM7502 RM4752 RM1623 RM1002 RD0101 RM1003 RM1003 RD0104 RD0224 RM1623 RD0473 RD0473 RM1623 RM4752 RM1502 RM2002 RM3012 RM4752 RM7502 RM1183 RM1783 RM2743 RD0473 RD0473 RD0101 RD0103 VI0052 VI0028 VI0028 VD0016 VI0102 VI0102 VI0102 VI0102 VI0102 VI0102 VI0102 VI0102 VI0102 VI0102 VN0108 VN0104 VN0108 VN0104 X80006 X40326 X35796 PART R335 R336 R337 R338 R339 R341 R342 R343 R345 R347 R348 R350 R351 R353 R355 R356 R357 R358 R362 R363 R364 R365 R366 R367 R368 R369 R370 R371 R375 R376 V100 V140 V141 X-BUS X-E1 X-E10 X-E2 X-E3 X-E4 X-E5 X-E6 X-E7 X-E8 X-E9 X-PWR X-RX X-SYN X-TX X052 X065 X099 DESCRIPT. Mini-Melf resistor Mini-Melf resistor Mini-Melf resistor Mini-Melf resistor Mini-Melf resistor Mini-Melf resistor Mini-Melf resistor Mini-Melf resistor SMD resistor Mini-Melf resistor Mini-Melf resistor SMD resistor SMD resistor Mini-Melf resistor SMD resistor SMD resistor Mini-Melf resistor Mini-Melf resistor Mini-Melf resistor Mini-Melf resistor Mini-Melf resistor Mini-Melf resistor Mini-Melf resistor Mini-Melf resistor Mini-Melf resistor Mini-Melf resistor SMD resistor SMD resistor SMD resistor SMD resistor IC - socket IC -socket IC -socket D-connector Lead socket Lead socket Lead socket Lead socket Lead socket Lead socket Lead socket Lead socket Lead socket Lead socket 8-pin connector 4-pin connector 8-pin connector 4-pin connector Crystal Crystal DTMF-quartz crystal VALUE 39k2 1% 0.25W 47k5 1% 0.25W 56k2 1% 0.25W 64k9 1% 0.25W 75k0 1% 0.25W 47k5 1% 0.25W 162k 1% 0.25W 10k0 1% 0.25W 100 R 5% 0.125 W 100k 1% 0.25W 100k 1% 0.25W 100 k 5% 0.125 W 220 k 5% 0.125 W 162k 1% 0.25W 47 k 5% 0.125 W 47 k 5% 0.125 W 162k 1% 0.25W 47k5 1% 0.25W 15k0 1% 0.25W 20k0 1% 0.25W 30k1 1% 0.25W 47k5 1% 0.25W 75k0 1% 0.25W 118k 1% 0.25W 178k 1% 0.25W 274k 1% 0.25W 47 k 5% 0.125 W 47 k 5% 0.125 W 100 R 5% 0.125 W 10 k 5% 0.125 W PLCC-52 1R piikit DIL-28 DIL-28 D-15S 90 ast.kulma d=1.35mm,1.8mm h=4.2mm d=1.35mm,1.8mm h=4.2mm d=1.35mm,1.8mm h=4.2mm d=1.35mm,1.8mm h=4.2mm d=1.35mm,1.8mm h=4.2mm d=1.35mm,1.8mm h=4.2mm d=1.35mm,1.8mm h=4.2mm d=1.35mm,1.8mm h=4.2mm d=1.35mm,1.8mm h=4.2mm d=1.35mm,1.8mm h=4.2mm 8.0000 MHz 4.032 MHz -+30ppm 3.579545 MHZ +-30PPM MANUF. Beyschlag Beyschlag Beyschlag Beyschlag Beyschlag Beyschlag Beyschlag Beyschlag Kamaya Beyschlag Beyschlag Kamaya Kamaya Beyschlag Kamaya Kamaya Beyschlag Beyschlag Beyschlag Beyschlag Beyschlag Beyschlag Beyschlag Beyschlag Beyschlag Beyschlag Kamaya Kamaya Kamaya Kamaya Methode TYPE MMA 0204-50 MMA 0204-50 MMA 0204-50 MMA 0204-50 BL MMA 0204-50 MMA 0204-50 MMA 0204-50 MMA 0204-50 Cannon Assmann Assmann Assmann Assmann Assmann Assmann Assmann Assmann Assmann Assmann Wisher Wisher Wisher Wisher Telequartz Meiden Meiden DA121073-5044 AP 102 B/g AP 102 B/g AP 102 B/g AP 102 B/g AP 102 B/g AP 102 B/g AP 102 B/g AP 102 B/g AP 102 B/g AP 102 B/g WKP-N8B1G-L WKP-N4B1G-L WKP-N8B1G-L WKP-N4B1G-L 8.00MHZ/B MQX-3H2-04032-20 MMA 0204-50 MMA 0204-50 MMA 0204-50 MMA 0204-50 MMA 0204-50 MMA 0204-50 MMA 0204-50 MMA 0204-50 MMA 0204-50 MMA 0204-50 MMA 0204-50 MMA 0204-50 MMA 0204-50 Last update 18.04.95 XA0014E4_FM5.f 22 Product: TDM-20-N (Forte i) / 28.1.1999 XA0014E4_FM5.f 23 Product: TDM-20-N (Forte i) / 28.1.1999 XA0014E4_FM5.f 24 Product: TDM-20-N (Forte i) / 28.1.1999 XA0014E4_FM5.f 25 Product: TDM-20-N (Forte i) / 28.1.1999 XA0014E4_FM5.f 26 Product: TDM-20-N (Forte i) / 28.1.1999 XA0014E4_FM5.f 27 Product: TDM-20-N (Forte i) / 28.1.1999 XA0014E4_FM5.f 28 Product: TDM-20-N (Forte i) / 28.1.1999 XA0014E4_FM5.f 29 Product: TDM-20-N (Forte i) / 28.1.1999 XA0014E4_FM5.f 30 Product: TDM-20-N (Forte i) / 28.1.1999 XA0014E4_FM5.f 31 Product: HS-10 / OH0002 Handset 28.1.1999 11.0 PRINCIPLES OF HANDSET OPERATION OH0002 Handset 11.0.1 Connector Signals: pin signal 1 2 9V ERP 3 4 5 6 7 GND SDA SCL I2CINT AGND EXTMIC mic 8 9 10 9 V operating voltage earphone input, HOOK (VOL = 0 dB, norm dev. 300 mVrms) (HOOK, 5 V / 0 V) logic ground, erphone audio-ground data for I2C path clock for I2C path interrupt for I2C path microphone audio-ground microphone HF input microphone output, PWR (normal deviation 1 Vrms) (PWR, 5 V / 0 V) 11.0.2 Audio I202 A and B are parallel audio-switches, and operate the earphone audio functions. Operational amplifiers I206 A and B are inter-connected and provide a push-pull input for the earphone capsule. Components 270-272 constitute a HOOK connection. Audio switches I230 A and B activate either the normal- (A223) or HF-microphone. I228B works as preamplifier for both microphones, and I228A is an active low-pass filter, having a cut-off frequency of approx 3400 Hz. I230 C and D are parallel switches for microphone audio. 11.0.3 Automatic Control For Keyboard And Lcd Backlight Light dependable resistor (R130) controls I135A, which feeds transistor Q132. Q132 adjusts supply voltage (about 6...8V) to the backlight leds. IC circuit I135B switches off the lights totally when ambient lighting increases enough. 11.0.4 Leds LEDs D141-D146 illuminate LCD, and D151-D164 illuminate the keyboard. The radio may turn both of them separately on and off. In bright light, the illumination is also turned off by the dimmer-control. XH0002E4_fm5.fm 1 Product: HS-10 / OH0002 Handset 28.1.1999 Symbol- LEDs D171, D173, D175, D177, D179, and D180 can all be individually switched on and off. They have no brightness control. The LED series resistors adjus LEDs of different colors to the same brightness. All LED controls come from I130, which is an I/O circuit controlled by I2C path. Pins A0, A1 and A2 are used for coding all circuits to different path addresses so that the radio can control them individually. 11.0.5 Keyboard The keyboard is controlled primarily by I110, and partly by I120. The keyboard base is rubber matting, and the contacts are PCB foils. The I/O-lines of I120 have been determined as outputs, and the I110 I/O-lines are all inputs. In stand-by, the inputs are at 5 V, and the outputs are at 0 V. When a key is pressed, I110 activates interrupt (I2CINT-line goes to zero), and the radio scans the keyboard matrix until it locates the pressed key. Each of the outputs P0...P2 (I220) alternates between 5 V and 0 V, and the states are read via I110. 11.0.5.1 Display I100 is an I2C path-controlled display control-circuit. It controls the LCD- display directly with 44 outputs. The display is 4/1-multiplexed. There are 4x40 (=160) individually controlled LCD segments. R103 determines the multiplexing frequency, and R100-R102 provide LCD temperature compensation. 11.0.5.2 Power Supply I261 is a 5 V regulator, which drops the 9 V voltage coming from the radio to a 5 V voltage for logic circuits. There is separate regulator for LCD: D264, which provides a voltage of 5.6 V (the temperature compensation requires more than 5 V). XH0002E4_fm5.fm 2 Product: HS-10 / OH0002 Handset 28.1.1999 11.0.5.3 Parts list CODE PART DESCRIPT. VALUE MANUF. TYPE AD4629 AEE004 AMY063 CC0223 CC0223 CC0223 CC0223 CC0101 CC0101 CC0473 CB0224 CU0105 CU0106 CC0680 CD0101 CC0473 CC0392 CC0680 CC0473 CC0473 CC0331 CB0224 CU0105 CU0106 CC0473 CU0106 CC0473 DLG050 DLG050 DLG050 DLG050 DLG050 DLG050 DLG050 DLG050 DLG050 DLG050 DLG050 DLG050 DLG050 DLG050 DLG050 DLG050 DLG050 DLG050 DLG050 DLG050 DLY050 DLG050 DLR050 DLY050 DLY050 DLY050 DZ0569 DZ0569 II8576 II8574 A100 A207 A223 C102 C110 C120 C130 C134 C139 C206 C210 C216 C221 C222 C223 C224 C226 C227 C228 C232 C242 C248 C251 C260 C261 C262 C264 D141 D142 D143 D144 D145 D146 D151 D152 D153 D154 D155 D156 D157 D158 D159 D160 D161 D162 D163 D164 D171 D173 D175 D177 D179 D181 D221 D264 I100 I110 Benefon LCD I 46x29mm 6xalpha,10x7seg+6 Phi/Varitr LP-1707-B (=Ph) Microphone Omnidirectio SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD tantal SMD tantal SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD tantal SMD tantal SMD capasitor SMD tantal SMD capasitor SMD led SMD led SMD led SMD led SMD led SMD led SMD led SMD led SMD led SMD led SMD led SMD led SMD led SMD led SMD led SMD led SMD led SMD led SMD led SMD led SMD led SMD led SMD led SMD led SMD led SMD led SMD zener SMD zener LCD driver 8 bit I/O -42-+3dB 22 nF 10% 50 V X7R 22 nF 10% 50 V X7R 22 nF 10% 50 V X7R 22 nF 10% 50 V X7R 100 pF 5% 50V NP0 100 pF 5% 50V NP0 47 nF 10% 50 V X7R 220 nF 20% 50 V X7R 1uF/16V 20% 3.2x1.6mm 10uF/16V 20% 6x3.2mm 68 pF 5% 50 V NP0 100 pF 5% 50 V NP0 47 nF 10% 50 V X7R 3.9 nF 10% 50 V X7R 68 pF 5% 50 V NP0 47 nF 10% 50 V X7R 47 nF 10% 50 V X7R 330 pF 5% 50 V NP0 220 nF 20% 50 V X7R 1uF/16V 20% 3.2x1.6mm 10uF/16V 20% 6x3.2mm 47 nF 10% 50 V X7R 10uF/16V 20% 6x3.2mm 47 nF 10% 50 V X7R Green Green Green Green Green Green Green Green Green Green Green Green Green Green Green Green Green Green Green Green Yellow Green Red Yellow Yellow Yellow 5V6 5% 300mW 5V6 5% 300mW 160-segment I2C I2C Matsushita Philips Philips Philips Philips Philips Philips Philips Philips Matsushita Matsushita Philips Philips Philips Philips Philips Philips Philips Philips Philips Matsushita Matsushita Philips Matsushita Philips Citizen Citizen Citizen Citizen Citizen Citizen Citizen Citizen Citizen Citizen Citizen Citizen Citizen Citizen Citizen Citizen Citizen Citizen Citizen Citizen Citizen Citizen Citizen Citizen Citizen Citizen Philips Philips Philips Philips WM-060AY XH0002E4_fm5.fm ECST1CY 105R ECST1CC 106R ECST1CY 105R ECST1CC 106R ECST1CC 106R CL-50G-CD CL-50G-CD CL-50G-CD CL-50G-CD CL-50G-CD CL-50G-CD CL-50G-CD CL-50G-CD CL-50G-CD CL-50G-CD CL-50G-CD CL-50G-CD CL-50G-CD CL-50G-CD CL-50G-CD CL-50G-CD CL-50G-CD CL-50G-CD CL-50G-CD CL-50G-CD CL-50Y-CD CL-50G-CD CL-50UR-CD CL-50Y-CD CL-50Y-CD CL-50Y-CD BZX84C5V6 BZX84C5V6 PCF8576T PCF8574T 3 Product: HS-10 / OH0002 Handset 28.1.1999 CODE II8574 II8574 IA0272 IH4066 IA3182 IA3182 IH4066 IR2951 PH0002 QS0051 QSC849 QSC849 QS0054 QSC849 QSC849 QSC849 QSC849 QSC849 QSC849 QSC849 QSC849 QSC849 QSC849 RTN153 RC0562 RC0332 RC0184 RC0102 RC0102 RTL678 RC0103 RC0104 RC0104 RC0104 RC0102 RC0153 RC0104 RC0473 RC0105 RC0221 RC0221 RC0221 RC0103 RC0102 RC0103 RC0102 RC0271 RC0271 RC0331 RC0331 RC0331 RC0221 RC0271 RC0222 RC0103 RC0391 RC0103 RC0391 RC0103 RC0391 PART I120 I130 I135\ I202\ I206\ I228\ I230\ I261 PCB Q132 Q148 Q150 Q151 Q170 Q172 Q174 Q176 Q178 Q180 Q201 Q236 Q246 Q271 R100 R101 R102 R103 R104 R105 R130 R131 R132 R133 R134 R135 R136 R137 R138 R139 R141 R143 R145 R147 R148 R149 R150 R151 R153 R155 R157 R159 R161 R163 R165 R170 R171 R172 R173 R174 R175 XH0002E4_fm5.fm DESCRIPT. 8 bit I/O 8 bit I/O 2 x op.amp. 4xbilateral switch 2xop.amp. 2xop.amp. 4xbilateral switch Regulator PCB handset SMD transistor SMD transistor SMD transistor SMD transistor SMD transistor SMD transistor SMD transistor SMD transistor SMD transistor SMD transistor SMD transistor SMD transistor SMD transistor SMD transistor SMD-NTC resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor LDR-SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor VALUE I2C I2C LinCMOS Low noise,power HCMOS Low power,jfet input Low power,jfet input HCMOS 100mA 5V adj. 5% 46.0 x 153 x 1.6 FR4 (x4pcs) PNP 1.5A/45V NPN 0.2A/30V F=1.2dB NPN 0.2A/30V F=1.2dB NPN 1.5A/45V NPN 0.2A/30V F=1.2dB NPN 0.2A/30V F=1.2dB NPN 0.2A/30V F=1.2dB NPN 0.2A/30V F=1.2dB NPN 0.2A/30V F=1.2dB NPN 0.2A/30V F=1.2dB NPN 0.2A/30V F=1.2dB NPN 0.2A/30V F=1.2dB NPN 0.2A/30V F=1.2dB NPN 0.2A/30V F=1.2dB 15k 5% 3.7%/C 5.6 k 5% 0.125 W 3.3 k 5% 0.125 W 180 k 5% 0.125 W 1 k 5% 0.125 W 1 k 5% 0.125 W 50-200k...5M 10 k 5% 0.125 W 100 k 5% 0.125 W 100 k 5% 0.125 W 100 k 5% 0.125 W 1 k 5% 0.125 W 15 k 5% 0.125 W 100 k 5% 0.125 W 47 k 5% 0.125 W 1 M 5% 0.125 W 220 R 5% 0.125 W 220 R 5% 0.125 W 220 R 5% 0.125 W 10 k 5% 0.125 W 1 k 5% 0.125 W 10 k 5% 0.125 W 1 k 5% 0.125 W 270 R 5% 0.125 W 270 R 5% 0.125 W 330 R 5% 0.125 W 330 R 5% 0.125 W 330 R 5% 0.125 W 220 R 5% 0.125 W 270 R 5% 0.125 W 2.2 k 5% 0.125 W 10 k 5% 0.125 W 390 R 5% 0.125 W 10 k 5% 0.125 W 390 R 5% 0.125 W 10 k 5% 0.125 W 390 R 5% 0.125 W MANUF. Philips Philips Texas RCA Motorola Motorola RCA National TYPE PCF8574T PCF8574T TLC27M2ID 74HC4066B MC 33182D MC 33182D 74HC4066B LP2951CM Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Hokuriku Kamaya Kamaya Kamaya Kamaya Kamaya Moririca Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya BCX 51 BC 849 C BC 849 C BCX 54 BC 849 C BC 849 C BC 849 C BC 849 C BC 849 C BC 849 C BC 849 C BC 849 C BC 849 C BC 849 C MKY-54L678 4 Product: HS-10 / OH0002 Handset 28.1.1999 CODE RC0103 RC0391 RC0103 RC0391 RC0103 RC0391 RC0104 RC0393 RC0103 RC0103 RC0102 RC0153 RC0104 RC0153 RC0104 RC0104 RC0102 RC0272 RC0184 RC0183 RC0224 RC0153 RC0222 RC0184 RC0104 RC0393 RC0393 RC0103 RI0203 RC0333 RC0184 RC0104 RC0393 RC0104 RC0104 RC0104 RC0103 RC0101 RC0101 RC0101 RC0222 RC0104 RC0104 RC0103 000000 000000 000000 000000 000000 000000 000000 000000 000000 000000 000000 000000 000000 000000 000000 000000 PART R176 R177 R178 R179 R180 R181 R200 R201 R205 R206 R207 R209 R210 R211 R215 R216 R220 R221 R224 R225 R226 R227 R231 R232 R235 R236 R238 R239 R240 R241 R242 R245 R246 R248 R250 R251 R255 R256 R257 R258 R264 R270 R271 R272 S110 S111 S112 S113 S114 S115 S116 S117 S120 S121 S122 S123 S124 S125 S126 S127 XH0002E4_fm5.fm DESCRIPT. SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD trimmer resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor VALUE 10 k 5% 0.125 W 390 R 5% 0.125 W 10 k 5% 0.125 W 390 R 5% 0.125 W 10 k 5% 0.125 W 390 R 5% 0.125 W 100 k 5% 0.125 W 39 k 5% 0.125 W 10 k 5% 0.125 W 10 k 5% 0.125 W 1 k 5% 0.125 W 15 k 5% 0.125 W 100 k 5% 0.125 W 15 k 5% 0.125 W 100 k 5% 0.125 W 100 k 5% 0.125 W 1 k 5% 0.125 W 2.7 k 5% 0.125 W 180 k 5% 0.125 W 18 k 5% 0.125 W 220 k 5% 0.125 W 15 k 5% 0.125 W 2.2 k 5% 0.125 W 180 k 5% 0.125 W 100 k 5% 0.125 W 39 k 5% 0.125 W 39 k 5% 0.125 W 10 k 5% 0.125 W 20k 20% 0.25W 33 k 5% 0.125 W 180 k 5% 0.125 W 100 k 5% 0.125 W 39 k 5% 0.125 W 100 k 5% 0.125 W 100 k 5% 0.125 W 100 k 5% 0.125 W 10 k 5% 0.125 W 100 R 5% 0.125 W 100 R 5% 0.125 W 100 R 5% 0.125 W 2.2 k 5% 0.125 W 100 k 5% 0.125 W 100 k 5% 0.125 W 10 k 5% 0.125 W MANUF. Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Copal Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya TYPE ST-4A 5 Product: HS-10 / OH0002 Handset 28.1.1999 CODE 000000 000000 000000 000000 000000 000000 000000 000000 AR0014 000000 000000 VM0110 PART S130 S131 S132 S133 S134 S135 S136 S210 S270 V207 V222 V260 DESCRIPT. VALUE MANUF. TYPE Reed switch 15-20AT l=14.2 mm Philips RI-27AA Contact strip angle 1 x 10 NB-electr. PH3-10-10G Last update 18.04.95 XH0002E4_fm5.fm 6 Product: HS-10 / OH0002 Handset 28.1.1999 Component Side Layout PH0002A0 (Schematic OH0002A-C0) XH0002E4_fm5.fm 7 Product: HS-10 / OH0002 Handset 28.1.1999 Solder Side Layout PH0002A0 (Schematic OH0002A-C0) XH0002E4_fm5.fm 8 Product: HS-10 / OH0002 Handset 28.1.1999 XH0002E4_fm5.fm 9 Product: HS-10 / OH0002 Handset 28.1.1999 XH0002E4_fm5.fm 10 Product: HS-10 / OH0002 Handset 28.1.1999 XH0002E4_fm5.fm 11 Product: DA-10 / OO0402 28.1.1999 12.0 DATA-INTERFACE FUNCTION OUTLINE OO0402 The data-interface can be divided into three functional parts: the processor, audio, and ring and line voltage circuits. Circuit diagrams are also separated into these three sections. 12.0.1 The Processor The processor function is provided by I010 MC68HC11 chip, which uses a 3.57 MHz crystal X010. Program memory is provided by 64k*8 EPROM I030. Program memory and external I/O circuit address coding is performed by I050 and I060. Communication between the processor and the radio unit uses an IIC-bus connected to I070, I080, I090 and I100. Each chip is connected to the processor databus with latch circuit. The battery supported IIC-RAM I120 is connected to the processor IIC bus. The circuit is set to "power-saving" mode by inverting the regulator I001 ERROR output with Q121. The DTMF receiver I040 interprets codes sent from the tele-VDU and feeds them to the processor through the I/O port. The oscillator I040 input is connected to the processor’s oscillator output. The logical +5V power supply is regulated by I001, the ERROR output of which is used to reset the processor. 12.0.2 Memory Addresses I030 EPROM I071 LATCH 1081 LATCH I091 LATCH I110 LATCH CPU inc. RAM 8000H - FFFFH 4000H 5000H 6000H 7000H OOH - FFH program memory keyboard (input) indicator values tariff rate reception keyboard (output) 12.0.3 Interrupts The DTMF-receiver I040 StD output is activated by the circuit detecting a DTMF signal. This generates an "input capture" timer-interrupt to processor I010 (PAO/IC3). Keyed in numeric codes (inc. * and #) are saved in the number buffer, with room for 23 digits. As the number buffer becomes full, further input is ignored. The first DTMF code received suppresses the dialling tone by grounding the audio frequency generator processor pins PA5/OC4, PA5/OC3 and PA6/OC2. A DTMF interrupt activates a 7 second timer which will also display "number ready" mode. Xo0402e4_fm5.fm 1 Product: DA-10 / OO0402 28.1.1999 The system clock’s interrupt interval is 9.15424 ms. The clock updates the SW counters, which are used for timing functions, dialling-tone formation (call, dial, busy), and directing the adapter transfer modes. The timer PA5/OC3 is used to generate a 25 Hz call tone. The relevent frequency half-cycle is loaded into register TOC3; pin OC3 connected as the output pin (TCTL1 register); the OC3 interrupt flag is nullified in register RFLG1 and an interrupt is allowed by activating the relevant interrupt-bit in register TMSK1. When the ouput-compare register corresponds to the reference clock value, the interrupt is completed and a new half-cycle reading is loaded into register TOC3. The output square-wave is of 25 Hz frequency. Call-tone duration is governed by the above mentioned system-clock interrupts from the synchronised SW counters. Dialling- and busy-tones are formed using PA4/PC4 output. The frequency in both cases is 425 Hz. Busy-tone cycle is 300/300 ms. Tone generation is similar to the process described above. (Dialling-tone is not broken by the SW counters). The PA6/OC2 output is reserved for generation of a tariff-pulse (16 kHz). This is not in use with the data-interface. 12.0.4 Processor I/O Functions During an input-capture interrupt, DTMF data is read from gate E pins PE0 ... PE3. EXAL (incoming call) is registered at E gate pin PE4. TERMHOOK (accessory hook) is registered at gate A pin PA2. IN USE (PD3) control activates the data-interface and prevents simultaneous operation of tele-VDU and accessories. RING GATE (PD5) - 120V regulator required for data-interface call functions. IIC RAM circuit I120 data and clock (PA7, PF4). Included is a pulse counter for use with the coin-operated version. The data-interface uses this circuit to store call data (ACALL and BCALL data). In case of a power failure with the adapter in call-mode, the RAM memory will be checked after reset, and operation will continue as before. If the call was terminated before reset, then the adapter will function normally, switching to dial-mode when the handset is lifted. IIC LATCH ENABLE (PD0). Control for latch circuit I110. The circuit is used to transfer a key-code to the radio unit. IIC-interrupt to the radio is simulated as follows: keyin the required code to the latch circuit I110, de-activate the PD0 control and wait until the latch circuit I071 can be read by the radio prompted keyboard scan. For each scan, the relevant code is written via PD0-control to I110. Finally, the corresponding key release interrupt is simulated. Call-mode is recognised by reading the CALL-led state from circuit I081. Continuous illumination of the led for one second during calibration indicates call-mode. Xo0402e4_fm5.fm 2 Product: DA-10 / OO0402 28.1.1999 12.0.5 Audio The telephone connection branch is formed by the operational amplifier I215. The branch is matched to 820R/38 nF line impedance with resistors R218, R219 and condensator C218. The telephone line, with +- 3.0 kHz deviation (1 kHz) and 3/7 loudness (400 mVrms), has a 600 Ohm resistive load with a -28 dBm signal level. Similarly, a -3dBm input level will provide 1.0 Vrms in the TXAUDIO line, with +- 3.0 kHz deviation in the transmitter. Audio tones (425 Hz) are filtered with the operational amplifier I205A, and then fed through the branch to the telephone line. Tariff pulses (12/16 kHz) are filtered with the operational amplifiers I235A, and are fed to the standard current modulated telephone line. The telephone line includes a return-feed constant current integrator I235, Q250, and Q251, to provide the telephone line loop current. The constant current load maintains the loop current supply without any loss of audio signal. Loop current switching is detected from the transistor Q265 constant current load emitter surplus potential. 12.0.6 Ring- And Line-voltage Power Supply The telephone connection line-potential (60 V) is derived from a current form flyback power supply. During operation, the control-circuit I341 measures the current flowing through the transformer primary windings at resistor R338. When the current exceeds the value specified by the control circuit, FET Q335 is de-activated. This results in the energy stored in the transformer being discharged from the secondary windings through diode D328 to output condensators C329 and C328. When the output drops to the value determined by resistors F342 and R343, the control circuit lowers the level at which FET Q335 switches. With RING-GATE control, offset-current is directed to the control circuit adjuster through resistor R347, resulting in an output voltage of 120V during the ring. The secondary current is limited with operational amplifier I205B, which measures the transformer secondary current flowing through resistor R371, and when secondary current limit is exceeded 1205B adjusts the control-circuit 1341 via diode D367. RING-control is normally in 0-state, and Q325 functions as a constant-current generator, providing a continuous voltage for FET Q323. This causes Q323 to conduct, and the line-voltage is fed to the telephone line. During a call, RING-line alternates between 1 and 0 at 25Hz, causing Q323 and Q326 to conduct in turn. As the powersupply voltage is raised to 120V in call-mode, the telephone line is provided with both 60V DC and 60V AC voltages. Xo0402e4_fm5.fm 3 Product: DA-10 / OO0402 28.1.1999 The audio signals are changed with relay A315 to the branch circuit with IN-USE control. The diode D303 allows radio unit to be switched off if for some reason the call cannot be terminated from the VDU. FET Q317 breaks the SDA-line, so that the keyboard is inoperative while the tele-VDU is in use. The display functions as normal as the diode D303 will permit writing to the screen. Xo0402e4_fm5.fm 4 Product: DA-10 / OO0402 28.1.1999 12.0.7 Parts list OO0402 CODE PART DESCRIPT. VALUE MANUF. TYPE AB0003 AR0004 CC0473 CC0473 CU0106 CC0473 CC0220 CC0220 CC0473 CC0473 CC0473 CC0473 CC0102 CC0473 CC0473 CC0473 CC0473 CC0473 CC0473 CC0473 CC0473 CC0473 CC0473 CC0473 CC0393 CC0393 CB0224 CC0332 CC0393 CE0106 CB0224 CC0102 CC0102 CC0152 CC0102 CU0105 CC0683 CC0103 CU0105 CP0683 CE0226 CE0226 CC0103 CC0471 CC0101 CC0152 CC0473 CE0337 CE0337 CE0337 CC0473 CC0473 CC0473 CC0473 A120 A315\ C001 C002 C003 C010 C011 C012 C020 C030 C040 C041 C044 C045 C050 C060 C070 C071 C080 C081 C090 C091 C100 C110 C203 C205 C212 C215 C218 C219 C226 C233 C235 C241 C245 C254 C263 C267 C282 C321 C328 C329 C333 C339 C345 C352 C353 C355 C356 C357 C373 C375 C376 C378 Lithium battery Relay SMD capasitor SMD capasitor SMD tantal SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor Al elko SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD tantal SMD capasitor SMD capasitor SMD tantal Polypropylen Al elko Al elko SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor Al elko Al elko Al elko SMD capasitor SMD capasitor SMD capasitor SMD capasitor 3V 180mAh d=20mm 9V/1.25A 47 nF 10% 50 V X7R 47 nF 10% 50 V X7R 10uF/16V 20% 6x3.2mm 47 nF 10% 50 V X7R 22 pF 5% 50V NP0 22 pF 5% 50V NP0 47 nF 10% 50 V X7R 47 nF 10% 50 V X7R 47 nF 10% 50 V X7R 47 nF 10% 50 V X7R 1 nF 5% 50V NP0 47 nF 10% 50 V X7R 47 nF 10% 50 V X7R 47 nF 10% 50 V X7R 47 nF 10% 50 V X7R 47 nF 10% 50 V X7R 47 nF 10% 50 V X7R 47 nF 10% 50 V X7R 47 nF 10% 50 V X7R 47 nF 10% 50 V X7R 47 nF 10% 50 V X7R 47 nF 10% 50 V X7R 39 nF 10% 50V X7R 39 nF 10% 50V X7R 220 nF 20% 50 V X7R 3.3 nF 5% 50 V NP0 39 nF 10% 50V X7R 10 uF/35 V 5x7mm 220 nF 20% 50 V X7R 1 nF 5% 50V NP0 1 nF 5% 50V NP0 1.5 nF 5% 50V NPO 1 nF 5% 50V NP0 1uF/16V 20% 3.2x1.6mm 68nF/50V/10%/X7R 10 nF 10% 50V X7R 1uF/16V 20% 3.2x1.6mm 68nF/250/160V 22 uF/160V 25x10mm 22 uF/160V 25x10mm 10 nF 10% 50V X7R 470 pF 5% 50 V NP0 100 pF 5% 50V NP0 1.5 nF 5% 50V NPO 47 nF 10% 50 V X7R 330uF/16V 20% 15x7.3mm 330uF/16V 20% 15x7.3mm 330uF/16V 20% 15x7.3mm 47 nF 10% 50 V X7R 47 nF 10% 50 V X7R 47 nF 10% 50 V X7R 47 nF 10% 50 V X7R Matsushita Takamisawa Philips Philips Matsushita Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Matsushita BR2032-1HG RA-9W-K Xo0402e4_fm5.fm Philips Matsushita Evox Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips ECST1CC 106R 2222 097 50109 ECST1CY 105R ECST1CY 105R PMR10 222204131229 222204131229 222213555331 222213555331 222213555331 5 Product: DA-10 / 28.1.1999 CODE DS0070 DS0099 DY0074 DS0070 DF0026 DS0070 DS0070 DS0099 IR2951 IP6811 IH0573 IM7512 IA8870 IH0138 IH0002 II8574 IH0573 II8574 IH0573 II8574 IH0573 II8574 IH0573 II8570 IA3182 IA0204 IA0272 IX2843 LA0106 LT0001 LA0105 VI0028 VI0052 NI3065 PO0003 QSC849 QSC849 QP0158 QSC849 QSC849 QSC849 QF0003 QF9210 QS0040 QS0040 QF0024 QSC849 QSC859 RC0223 RC0105 RC0104 RC0103 RC0103 RC0684 RC0223 RC0104 RC0104 RC0104 RC0334 RC0472 PART D120 D219 D303 D315 D328 D361 D367 D373 I001 I010 I020 I030 I040 I050 I060\ I070 I071 I080 I081 I090 I091 I100 I110 I120 I205\ I215\ I235\ I341 L321 L331 L357 MEC1 MEC2 MEC3 PCB Q121 Q250 Q251 Q265 Q306 Q311 Q317 Q323 Q325 Q326 Q335 Q370 Q371 R002 R010 R011 R012 R013 R041 R044 R045 R070 R120 R121 R123 Xo0402e4_fm5.fm DESCRIPT. SMD diode pair SMD diode Shottky diode SMD diode pair Diode (very fast) SMD diode pair SMD diode pair SMD diode Regulator 8-BIT MIKROPROS Octal D-latches One time prom CMOS DTMF decoder 3 to 8-line decod. inv. 4x2-inp.NOR 8 bit I/O Octal D-latches 8 bit I/O Octal D-latches 8 bit I/O Octal D-latches 8 bit I/O Octal D-latches SRAM 2xop.amp. Dual operational amp. 2 x op.amp. Current mode controller Inductor 9.5x4mm Transformer Incuctor 9.5x4mm IC -socket IC - socket Snap rivet (pikaniitti) PCB data-adapter SMD transistor SMD transistor Medium power transistor SMD transistor SMD transistor SMD transistor SMD n-channel FET SMD p-channel FET SMD transistor SMD transistor SMD n-channel SMD transistor SMD transistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor VALUE 70V/100mA common cathode 70 V 200 mA 70V/100mA common cathode 1A/400V 30ns 70V/100mA common cathode 70V/100mA common cathode 70 V 200 mA 100mA 5V adj. 5% 512 EEPROM, 8A/D, no ROM HCMOS 65.536 x 8b 200ns HCMOS HCMOS I2C HCMOS I2C HCMOS I2C HCMOS I2C HCMOS I2C 256x8bit Low power,jfet input High performance LinCMOS Low noise,power 10uH+-10% 0.34A Q=55(8MHz) DRW NO 2/90 1uH-+10% 0.9A Q=50(25MHz) DIL-28 PLCC-52 1R piikit Nylon 6, RMS-28 190 x 161,5mm FR4 (2x) NPN 0.2A/30V F=1.2dB NPN 0.2A/30V F=1.2dB NPN 0.5A/300V 20W NPN 0.2A/30V F=1.2dB NPN 0.2A/30V F=1.2dB NPN 0.2A/30V F=1.2dB 60V/0.75A Rds 3.2 200V/2A Rds=3 NPN 1A/250V NPN 1A/250V 60V/15A/Rds=0.1 NPN 0.2A/30V F=1.2dB PNP 0.2A/30V F=1.2dB 22 k 5% 0.125 W 1 M 5% 0.125 W 100 k 5% 0.125 W 10 k 5% 0.125 W 10 k 5% 0.125 W 680 k 5% 0.125 W 22 k 5% 0.125 W 100 k 5% 0.125 W 100 k 5% 0.125 W 100 k 5% 0.125 W 330 k 5% 0.125 W 4.7 k 5% 0.125 W MANUF. Philips Philips Philips Philips Philips Philips Philips Philips National Motorola Fujitsu Plessey RCA Philips Philips Philips Philips Philips Motorola SGS Texas Motorola Dale Salcomp Dale Methode Richco Benefon Philips Philips Motorola Philips Philips Philips I&R I&R Philips Philips I&R Philips Philips Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya TYPE BAV 70 BAV 99 BAT 74 BAV 70 BYV 26B BAV 70 BAV 70 BAV 99 LP2951CM MC68HC11A1FN 74HC573 MBM27C512P-20P MV8870 74HC138 74HC02 PCF8574T 74HC573 PCF8574T 74HC573 PCF8574T 74HC573 PCF8574T 74HC573 PCF8570T MC 33182D LS204M TLC27M2ID UC2843AN RM5 SCP7801 SR 3065B BC 849 C BC 849 C BD 158 BC 849 C BC 849 C BC 849 C IRFS 1Z3 IRFR 9210 BST40 BST40 IRFR024 BC 849 C BC 859 C 6 Product: DA-10 / 28.1.1999 CODE RC0472 RC0334 RC0121 RC0470 RC0564 RC0472 RC0333 RC0183 RC0102 RC0682 RC0223 RC0223 RC0183 RC0221 RC0223 RC0682 RC0102 RC0223 RC0103 RC0103 RC0472 RB6809 RC0104 RC0124 RC0103 RC0472 RC0104 RC0104 RC0104 RC0472 RC0103 RC0103 RC0472 RC0000 RC0103 RC0103 RC0472 RC0103 RC0150 RC0103 RC0560 RB0228 RC0102 RC0334 RC0103 RC0104 RC0333 RC0682 RC0104 RC0224 RC0472 RB1000 VD0016 VM0116 VP0077 X35796 PART R124 R201 R202 R203 R205 R211 R212 R215 R218 R219 R221 R222 R225 R226 R231 R232 R233 R235 R241 R245 R250 R251 R253 R254 R262 R263 R265 R281 R282 R303 R305 R306 R311 R315 R317 R323 R325 R326 R333 R335 R336 R338 R339 R342 R343 R345 R347 R352 R362 R365 R368 R371 VH01 VR01 VT01 X010 DESCRIPT. SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor Metal film resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor Metal film resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor Metal film resistor D-connector Contact strip angle Modular jack DTMF-quartz crystal VALUE 4.7 k 5% 0.125 W 330 k 5% 0.125 W 120 R 5% 0.125 W 47 R 5% 0.125 W 560 k 5% 0.125 W 4.7 k 5% 0.125 W 33 k 5% 0.125 W 18 k 5% 0.125 W 1 k 5% 0.125 W 6.8 k 5% 0.125 W 22 k 5% 0.125 W 22 k 5% 0.125 W 18 k 5% 0.125 W 220 R 5% 0.125 W 22 k 5% 0.125 W 6.8 k 5% 0.125 W 1 k 5% 0.125 W 22 k 5% 0.125 W 10 k 5% 0.125 W 10 k 5% 0.125 W 4.7 k 5% 0.125 W 68R 5% 0.4W 100 k 5% 0.125 W 120 k 5% 0.125 W 10 k 5% 0.125 W 4.7 k 5% 0.125 W 100 k 5% 0.125 W 100 k 5% 0.125 W 100 k 5% 0.125 W 4.7 k 5% 0.125 W 10 k 5% 0.125 W 10 k 5% 0.125 W 4.7 k 5% 0.125 W 0R 10 k 5% 0.125 W 10 k 5% 0.125 W 4.7 k 5% 0.125 W 10 k 5% 0.125 W 15 R 5% 0.125 W 10 k 5% 0.125 W 56 R 5% 0.125 W 0.22R 5% 0.4W 1 k 5% 0.125 W 330 k 5% 0.125 W 10 k 5% 0.125 W 100 k 5% 0.125 W 33 k 5% 0.125 W 6.8 k 5% 0.125 W 100 k 5% 0.125 W 220 k 5% 0.125 W 4.7 k 5% 0.125 W 100R 5% 0.4W D-15S 90 ast.kulma 2x8 Right angle 6/4cont. 3.579545 MHZ +-30PPM MANUF. Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Beyschlag Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Beyschlag Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Beyschlag Cannon NB-electr. Molex Meiden TYPE MBA0207-50 MBA0207-50 MBA0207-50 DA121073-5044 H4-6-16G 90077-1076 Last update 01.09.92 Xo0402e4_fm5.fm 7 Product: DA-10 / 28.1.1999 Component Side Layout PO0003A0 (Schematic OO0402A-C0) Xo0402e4_fm5.fm 8 Product: DA-10 / 28.1.1999 Solder Side Layout PO0003A0 (Schematic OO0402A-C0) Xo0402e4_fm5.fm 9 Product: DA-10 / 28.1.1999 Xo0402e4_fm5.fm 10 Product: DA-10 / 28.1.1999 Xo0402e4_fm5.fm 11 Product: DA-10 / 28.1.1999 Xo0402e4_fm5.fm 12 Product: Answering Machine / 28.1.1999 13.0 INSTALLATION OF ANSWERING MACHINE The answering machine is installed inside the transceiver unit. Place the transceiver unit on the table, the cooling plate away from yourself, so that the antenna connector is on its right side and the power connector on its left side, figure 1. Unscrew the head bolts, and remove the cover. Now you can see thr Audio/Processor voard and on its right side the connector-strip A, to which the answering machine is connected, figure 2. 1 A 2 Release screws 1 and 2, and place the Audio/Processor plastic foil peaks into the corresponding holes in connector-strip A. Fasten the unit with screws 3 and 4. 3 4 Check that all connector peaks are in their holes, and when you are sure that everything is in order, close the cover and test the machine. connector strip A answering machine board bush ring plastic foil Audio/Prosessor connector-strip Aanswering machine board Xo0004e4_fm5.fm 1 Product: Answering Machine / 28.1.1999 13.1 Answering Machine 13.1.1 Processor The central processing unit for the answering machine is Intel 80C31. The processor - reads the PROM program memory - stores the speech, digitized with the delta-modulator, in DRAM memory, and tran stored speech from RAM to the delta-modulator, - refreshes DRAM circuits - communicates via the I2c bus with other devices connected to the system, - controls the audio signal path control switches, - controls the ringing tone signal, - generates the "watchdog" reset pulse. 13.1.2 Memory Control The processor may uses the program memory D190 and the dynamic RAM D200D220. The memory addressing timing functions are assisted by control logic. The processor refreshes the dynamic RAM circuits at 8 ms intervals. 13.1.3 Watchdog D110C resonates at a frequency of approx 3 kHz, independent of the processor. This logic-level pulse is led to the counter D260. The watchdog reset pulse of the processor zeroes this counter at 8 ms intervals. There is no reset pulse when the program malfuctions. In that case the counter is free to proceed so that the counter D260A MSB will reset the processor. 13.1.4 Audio Paths The answering machine recognizes the audio signals coming from TXAIN- and RXAIN-lines. It transmits an audio signal to TXAOUT- and RXAOUT- lines. N230A ampflies the incoming audio signals. N240B is a compressor which drops the incoming audio signal dynamics to an appropriate level for the delta modulator. N170 is a delta modulator which converts the incoming audio signal to serial data. When repeating the stored speech, N170 converts the serial data coming from the memoriesn to an analog signal, which is led to the buffer amplifier N230d. The signal goes forward to the expander N240C, which then expands the comperssed speech dynamics to the original level. The compressor is followed by an active low-pass filter on which the processor-generated ringing-tone signal is combined. The last unit is the buffer amplifier N230C. The signal coming from N230C is led to either Xo0004e4_fm5.fm 2 Product: Answering Machine / 28.1.1999 RXAOUT- or TXAOUT-line with CMOS- switches N250C and N250D. 13.1.5 ICC-Operation Communication between the radio unit and the answering machine is accomplished with an IIC-bus (lines SDA, IICINT, and IICENA). When necessary, the radio unit can disconnect the SCL-line with N140D. There is an open-collector output (V291) on the IICINT-line; the up-draught resistor is at the radio unit. 13.1.6 Operating Voltages The answering machine gets its operating voltage from the radio unit (X290). The operating voltage range of the answering machine is 10.6 - 16 V dc. In stand-by, the current consumption is approx 20 mA; when recording and repeating speech, it is approx 90 mA. Xo0004e4_fm5.fm 3 Product: Answering Machine / 28.1.1999 13.1.7 Parts list CODE PART DESCRIPT. VALUE MANUF. TYPE CD0220 CD0220 CC0473 CD0102 CC0473 CC0473 CD0223 CD0223 CC0104 CC0473 CD0562 CD0562 CD0222 CC0473 CD0222 CD0222 CD0562 CC0473 CD0102 CC0473 CU0105 CU0105 CU0105 CC0104 CC0473 CU0105 CU0105 CU0105 CC0473 CU0106 CU0105 CC0473 CU0105 DS0099 DZ0919 DS0099 IP8052 IH0132 IH0032 IH0074 IH4053 IH0138 IX5564 IM1024 IM1024 IM1024 IA0324 IA0571 IH4053 IH0393 IR2951 QS1054 QSB848 RD0103 RD0104 RD0103 RD0223 C101 C102 C111 C112 C140 C171 C200 C210 C220 C230 C231 C232 C233 C234 C235 C236 C237 C238 C239 C240 C241 C242 C243 C244 C245 C246 C247 C248 C250 C280 C281 C282 C283 D100 D281 D290 I100 I110\ I120\ I130\ I140\ I150 I170 I200 I210 I220 I230\ I240\ I250\ I260\ I280 Q280 Q291 R110 R111 R200 R230 SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD capasitor SMD tantal SMD tantal SMD tantal SMD capasitor SMD capasitor SMD tantal SMD tantal SMD tantal SMD capasitor SMD tantal SMD tantal SMD capasitor SMD tantal SMD diode SMD zener SMD diode Prosessor (answ.mach.) 4x2 inp NAND schm. 4x2-inp OR 2xD-flip-flop 3x2-ch analog mpxer 3 to 8-line decod. inv. Deltamodulator DRAM DRAM DRAM 4 x opamp Compandor 3x2-ch analog mpxer Dual 4bit bin counter Regulator SMD transistor SMD transistor SMD resistor SMD resistor SMD resistor SMD resistor 22 pF 5% 50 V NP0 22 pF 5% 50 V NP0 47 nF 10% 50 V X7R 1 nF 5 % NP0 47 nF 10% 50 V X7R 47 nF 10% 50 V X7R 22 nF 10% 50 V X7R 22 nF 10% 50 V X7R 100 nF 10% 50V X7R 47 nF 10% 50 V X7R 5.6 nF 10% 50V 5.6 nF 10% 50V 2.2 nF 5% 50 V NP0 47 nF 10% 50 V X7R 2.2 nF 5% 50 V NP0 2.2 nF 5% 50 V NP0 5.6 nF 10% 50V 47 nF 10% 50 V X7R 1 nF 5 % NP0 47 nF 10% 50 V X7R 1uF/16V 20% 3.2x1.6mm 1uF/16V 20% 3.2x1.6mm 1uF/16V 20% 3.2x1.6mm 100 nF 10% 50V X7R 47 nF 10% 50 V X7R 1uF/16V 20% 3.2x1.6mm 1uF/16V 20% 3.2x1.6mm 1uF/16V 20% 3.2x1.6mm 47 nF 10% 50 V X7R 10uF/16V 20% 6x3.2mm 1uF/16V 20% 3.2x1.6mm 47 nF 10% 50 V X7R 1uF/16V 20% 3.2x1.6mm 70 V 200 mA 9V1 5% 300mW 70 V 200 mA CMOS (maskprom) HCMOS HCMOS HCMOS HCMOS HCMOS Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Matsushita Matsushita Matsushita Philips Philips Matsushita Matsushita Matsushita Philips Matsushita Matsushita Philips Matsushita Philips Philips Philips MatraHarri RCA RCA RCA RCA RCA Harris ECST1CY 105R ECST1CY 105R ECST1CY 105R Xo0004e4_fm5.fm 1MB x 1 1MB x 1 1MB x 1 HCMOS HCMOS 100mA 5V adj. 5% NPN 1.5A/45V NPN 0.1A/30V F=2dB 10 k 5% 0.125 W 100 k 5% 0.125 W 10 k 5% 0.125 W 22 k 5% 0.125 W Philips RCA National Philips Philips Kamaya Kamaya Kamaya Kamaya ECST1CY 105R ECST1CY 105R ECST1CY 105R ECST1CC 106R ECST1CY 105R ECST1CY 105R BAV 99 BZX84-C9V1 BAV 99 S80C52-xxx 74HC132 74HC32 74HC74 74HC4053 74HC138 HC55564 TMS4C1024D TMS4C1024D TMS4C1024D LM324 SA 571 74HC4053 74HC393 LP2951CM BCP 54 BC 848 B 4 Product: Answering Machine / 28.1.1999 CODE RD0223 RD0103 RD0103 RD0224 RD0104 RD0103 RD0104 RD0183 RD0183 RD0222 RD0332 RD0104 RD0104 RD0104 RD0182 RD0473 X10247 VM0210 PART R231 R232 R233 R234 R235 R236 R237 R240 R241 R242 R243 R280 R283 R284 R286 R290 X100 X290 DESCRIPT. SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor Crystal Contact strip adapter VALUE 22 k 5% 0.125 W 10 k 5% 0.125 W 10 k 5% 0.125 W 220 k 5% 0.125 W 100 k 5% 0.125 W 10 k 5% 0.125 W 100 k 5% 0.125 W 18 k 5% 0.125 W 18 k 5% 0.125 W 2.2 k 5% 0.125 W 3.3 k 5% 0.125 W 100 k 5% 0.125 W 100 k 5% 0.125 W 100 k 5% 0.125 W 1.8 k 5% 0.125 W 47 k 5% 0.125 W 10.245 MHz 30 ppm 1 x10-pin MANUF. Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Kamaya Meiden McKenzie TYPE SST 1x10-880S Last update 10.04.92 Xo0004e4_fm5.fm 5 Product: Answering Machine / 28.1.1999 Component Side Layout Xo0004e4_fm5.fm 6 Product: Answering Machine / 28.1.1999 Solder Side Layout Xo0004e4_fm5.fm 7 Product: Answering Machine / 28.1.1999 Xo0004e4_fm5.fm 8 Product: Answering Machine / 28.1.1999 Xo0004e4_fm5.fm 9 Product: Answering Machine / 28.1.1999 Xo0004e4_fm5.fm 10
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.2 Linearized : Yes Encryption : Standard V1.2 (40-bit) User Access : Print, Copy, Fill forms, Extract, Assemble, Print high-res Create Date : 1999:01:28 14:58:29 Producer : Acrobat Distiller 3.0 for Windows Title : E:\WIN3\DS4\BENELOGO.EPS Creator : FrameMaker+SGML 5.5.3L15a Modify Date : 1999:01:29 12:43:14 Page Count : 134 Page Mode : UseOutlinesEXIF Metadata provided by EXIF.tools