dormakaba Canada R79KSR Wall Mounted RFID Reader User Manual

Kaba Ilco Inc. Wall Mounted RFID Reader Users Manual

Users Manual

Installation SheetRFID Wall Mounted Reader Installed with ILCO RAC 4 or RAC 4XTIntroductionThe RFID wall mounted reader provided by Kaba is compact, lightweight, rugged and water resistant, able to withstand temperatures from -30°F to 150°F (-35°C to 66°C). It is made from durable materials and comes with at least 15 feet (4.6 m) of cable. The reader is capable of functioning up to distances of 500 feet (152.4 m) when powered from the RAC controller board.The reader has a blue LED that indicates that the unit is powered. The reader also provides visual feedback when access is granted.Installing the Reader IMPORTANT: For proper dimensions required for the holes to be drilled, refer to drilling template DT-514800. If unavailable, drilling templates may be obtained through Kaba Customer Support: 1-800-906-4526As shown in Figure B and Table 1, the RFID wall mounted reader connects to the RAC 4/4XT controller board for single or dual reader applications. 1. As per the installation type, mark and drill the required holes for the reader as per drilling template DT-514800, or using the mounting plate of the reader. 2. Screw the mounting plate of the reader to the wall using the screws provided. Use the 1 ¼” wood screws and inserts for drywall, or use the ½” steel screws for metal frame mounting. 3. Connect one end of the supplied wire to the back of the reader as per the column ‘Reader Connection’ in Table 1 or as per Figure A. Route the other end of the wire, which will connect to the RAC enclosure, through the grommet in the mounting plate. 4. Hook the top of the reader enclosure onto the top of the mounting plate and secure together with the provided #6 screw, tightened at the bottom of the reader. 5. Route the wire to the RAC 4/4XT enclosure and connect to the controller board as per the column ‘RAC 4/4XT Controller Board Connection’ in Table 1, or as per Figure B. IMPORTANT: The jumper cables supplied with the reader must be connected as shown in Figure B and Table 1 for the contactless reader to operate properly. NOTE: The RAC 4 controller board supports a single reader only, for Ingress functionality, using connectors J1 and J2. NOTE: The RAC 4XT controller board can support dual readers for Ingress (connectors J1 & J2) and Egress (connectors J13 & J14) functionality.
ControllerBoard124-511689-002123BypassActiveResetSW1SW2D46D45D41D42J1 J2 J3J5J6J7J8J9J12J13J14J15J16J17J18J19D43D44ProgrammingPortSW3WHITEGREENWHITEGREENBLACKREDBLACKON123123123123 123 1212341234123 4 123 4123123 4123 4For EGRESSApplicationREDFor INGRESSApplicationSee Note 1*WHITEGREENBLACKJ42 1J52 1REDController Board to RFID Wall Mounted Reader ConnectionRAC4/4XT Controller Board Connection Signal Reader ConnectionGND J4 - 2 J1, Pin 2 J14, Pin 2 +12V J4 - 1 J1, Pin 3 J14, Pin 3 RS485+ J5 - 2 J2, Pin 1 + J3, Pin 1* J13, Pin 1 + J12, Pin 1 RS485- J5 - 1 J2, Pin 2 + J3, Pin 2* J13, Pin 2 + J12, Pin 2 Green See Note 1 Note 1: Jumper cables as shown in figure B must be connected for the reader to operate correctly.Wire ColorRedBlackSee Note 1WhiteCommentsGND+12V Ingress ReaderTerminal Block Egress ReaderKaba Ilco Inc.7301 Boul. Décarie, Montréal, Québec, H4P 2G7T: (514) 735-5411, TF: 1-800-906-4526, F: (514) 735-1394lodgingtech@kaba.com, www.kabalodging.comPK3660_10_14 Printed in CanadaFigure A: RFID Wall Mounted ReaderSurface MountFlush MountTable 1: RAC 4/4XT RFID Wall Mounted Reader Wire ConnectionsFigure B: RAC 4XT Controller Board (Note: RAC 4 Ingress only)Installation SheetRFID Wall Mounted Reader Installed with ILCO RAC 4 or RAC 4XTRegulatory Compliance:This device complies with Part 15 of the FCC Rules,. Operation is subject to the following two conditions: (1) this device may not cause harmful inter-ference, and (2) this device must accept any interference received, including interference that may cause undesired operation.Any changes or modifications of this product, not approved by manufacturer will void the user’s authority to operate the equipment.“This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.”FCC # Q8SR79KSRIC# 4652A-R79KSR

Navigation menu