dormakaba Canada SAFFIRELX Wireless door lock User Manual Product Release Plan

dormakaba Canada Inc. Wireless door lock Product Release Plan

Contents

Users manual

Page 1 of 28 Saffire LX SAFFIRE LX Installation Guide Outline Document Revision: Draft 1.0
Page 2 of 28 Saffire LX Table of Contents Table of Contents 1. Introduction and disclaimers ................................................................... 32. Recommended Tools ............................................................................. 33. Components ......................................................................................... 44. Install key cylinder (optional) ................................................................. 65. Install thumbturn spindle (optional) ........................................................ 66. Install the lock spindle ........................................................................... 77. Setting up the inside trim assembly ......................................................... 98. Installing the locking mechanism on the door ......................................... 128.1. Installing the mortise ASM (if lock equipped) ....................................... 12 8.2. Installing the cylindrical models (if lock equipped) ................................ 15 9. Installing the lock housings on the door ................................................. 1810. Connecting the cables .......................................................................... 1911. Installating inside cover ....................................................................... 2012. Installing the outside lever handle ......................................................... 2313. Install the batteries ............................................................................. 2314. Test lock functionality .......................................................................... 2415. Program the lock ................................................................................. 24Annex A.. ................................................................................................... 25 Annex B…………………………………………………………………………………………………………..………..28 Model: Saffire LX This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. Made in Canada ©2018 dormakaba Lodging Systems.All trademarks and registered trademarks are the property of their respective owners. Caution: Changes or modifications to this equipment not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
Page 3 of 28 Saffire LX 1. Introduction and disclaimersCaution: Please read and follow all directions carefully. Wear safety glasses when making the holes. Target Audience: These instructions are designed for use by maintenance professionals or lock installers who are familiar with common safety practices and competent to perform the steps described. dormakaba is not responsible for damage or malfunction due to incorrect installation however arising. Important: Carefully inspect windows, doorframe, door, etc. to ensure that the recommended procedures will not cause damage. dormakaba Lodging Systems standard warranty does not cover damages caused by installation. Respect applicable building codes regarding handle height. Definition of Terms: In these instructions, the term ASM refers to American Standard Mortise and ADB refers to Autodeadbolt Mortise. Technical Assistance For technical assistance, call: 1.877.468.3555 / +1.514.340.9025RT: 1.800.999.6213 / +1.248.837.3700 2. Recommended Tools
Page 4 of 28 Saffire LX 3. Components
Page 5 of 28 Saffire LX For doors more than 2 1/2" thick up to 3 3/4", order the appropriate hardware bag to receive the correct length of spindles and mounting screws. Part# 062-XXXXXX-XXX; (XXX = choice of finish). For outdoor installations, order gasket 033-515996-1 for standard lock and 033-515996-2 for MKO lock. Hardware
Page 6 of 28 Saffire LX 4. Install key cylinder (optional) • Insert the cylinder core in the key override housing. • Secure the cylinder core using screw (item 11). • Secure the access plate key cylinder (item 9) over the key override housing. • Secure the access plate using two screws (item 10). 5. Install thumb turn spindle (optional) • Verify that the line markers for the thumb turn hole are aligned. If the holes are misaligned, use the flat screwdriver to correct the position. • Insert the thumb turn spindle (item 2) into the thumb turn hole. Press firmly to ensure the spindle clicks in place. • Rotate the spindle to ensure that the part remains in place.
Page 7 of 28 Saffire LX 6. Install the lock spindle The spindle must be installed and properly secured in the front lock housing assembly. The spindle is used to connect the handle to operate the opening and closing door mechanism. Prior to installing the spindle, you must first adjust the required positioning of the hub receiving the spindle. There are 2 modes, Left Hand (LH) and Right Hand (RH) according door handing. • Turn the hub for correct door handing by turning clockwise for right and counter clockwise for left. • Lines to be aligned
Page 8 of 28 Saffire LX • Insert the spindle (item 1) smoothly until it clips.
Page 9 of 28 Saffire LX 7. Setting up the inside trim assembly Decide if the lever handle is a RH or LH position based on the door handing. The inside lever handle must be installed as is does not come preinstalled. • To set proper handing, insert the lever from the back plate and turn in the direction required for the handing (L or R).
Page 10 of 28 Saffire LX • Install the bushing (item 7) • Install the lever vertically as shown (pointing down), making sure it is snug. • Rotate the lever handle to horizontal position corresponding to selected handing. • Push up the spring holder and install the snap holder for spring holder (item 8) to lock and prevent lever from disengaging RH as arrow pointing R LH as arrow pointing L
Page 11 of 28 Saffire LX
Page 12 of 28 Saffire LX 8. Installing the locking mechanism on the door Before starting the installation of the lock on the door, please make sure the door has been prepared properly with proper holes for the lock. Refer to corresponding drilling template for your lock model. Drilling templates are available in the center section of this installation instructions and on the dormakaba website. 8.1. Installing the mortise ASM (if lock equipped) Before installing the mortise, verify gap between the door and the frame. The gap between the mortise face plate and the strike must not exceed ¼” for proper and secure operation of the mortise.
Page 13 of 28 Saffire LX • Verify the mortise handing for LH or RH. If the handing needs to be adjusted, refer to instructions in annex A. • Remove the face plate by removing the two screws
Page 14 of 28 Saffire LX • Insert the mortise in the side of the door. If the mortise is equipped with a cable, route the cable so it comes out of top hole on the side of the inside trim assembly. • Use metal or wood screws depending door material to secure the mortise
Page 15 of 28 Saffire LX • Re-install the face plate with its two screws. • Install the strike and the dust box on the door frame Important: When strike is installed on wood frames under one inch thick, wood screws supplied are not adequate. Use screws of efficient lenght to engage the structural stud behind the frame. Use only the strike and dust box supplied. Use of non-approved parts may void the warranty. 8.2. Installing the cylindrical models (if lock equipped) IMPORTANT For cylindrical latch models, ensure the dead-locking pin will stop against the strike when the door is closed (see figure). An incorrect installation that permits
Page 16 of 28 Saffire LX the pin to slip inside the strike may result in a total lockout and will void the warranty of the complete lock mechanism. • Insert the latch in the hole in the edge of the door, orienting them latch bolt head as per closing direction • Tighten the two screws. • Verify the door thickness. The lock is assembled in factory for door thickness of 1 ¾”. If the door thickness is different, refer to table below to adjust the spacers. Extra spacers and screws provided in the hardware bag.
Page 17 of 28 Saffire LX • Make sure the handing is correct. If not, reinstall the cylindrical unit for proper handing. • Install the cylindrical unit from outside of the door toward inside, so that it engages the latch as shown. • Install the strike and the dust box on the door frame Important: Use only the strike and strike box supplied. The use of non-approved parts will result in a functionality problem and may void the warranty.
Page 18 of 28 Saffire LX 9. Installing the lock housings on the door Install the housing on the inside of the door and aligning with the lock mechanism. • Install the front lock housing, routing the wire cable by the center hole at the top • Install the inside housing • Install the screws provided and tighten LH shown
Page 19 of 28 Saffire LX 10. Installing the antenna module (if lock equipped) • Position the bracket on the door, engaged with the “T” at the top of the chassis • Secure the bracket with screw 11. Connecting the cables Locks without wire guide • Connect each cable with its mating one and push back in the hole in the door the excess of cables.
Page 20 of 28 Saffire LX Locks with wire guide • Before installing the lock on the door, extend the wire guide out, without removing the cover. • After securing the front lock housing with the inside trim chassis, remove the cover on the wire cover. The cover will no longer be used. Wire guide
Page 21 of 28 Saffire LX o Now that cables are exposed, connect each cable with its mating one. o Push back the wire guide in the door. 12. Installating inside cover • Set the thumb turn on the inside cover to vertical position • Slide the inside cover onto the lever handle taking care not to scratch the lever handle • When the cover is fully in place, secure it using the 3 screws (item 5)
Page 22 of 28 Saffire LX • For locks with ADB mortise, to apply the privacy thumb turn sticker.
Page 23 of 28 Saffire LX 13. Installing the outside lever handle • Install the outside bushing, making sure it is snug • Install the outside lever handle according to the lock handing (L/R) • Insert the set screw and tighten till snug 14. Install the batteries • Insert the batteries in the battery holder respecting the polarity indicated in the battery holder IMPORTANT: Use only Alkaline batteries
Page 24 of 28 Saffire LX 15. Test lock functionality Make sure room door is open before testing A - Present Test Keycard B - Check Green & Red Lights Flash C - Rotate Outside Lever to Check Bolt Retraction D - Release Outside Lever, Should Move Freely E - Rotate Inside Lever to Check Bolt Retraction F - Check Bolt Projection from Thumbturn 16. Program the lock Refer to system user manual for lock programming.
Page 25 of 28 Saffire LX
Page 26 of 28 Saffire LX
Page 27 of 28 Saffire LX
Page 28 of 28 Saffire LX Annex B Install Outside Housing with Gasket

Navigation menu