e DATA TT1000 Badge Reader User Manual installation

e-DATA GmbH Badge Reader installation

Contents

installation user manual

Download: e DATA TT1000 Badge Reader User Manual installation
Mirror Download [FCC.gov]e DATA TT1000 Badge Reader User Manual installation
Document ID1246811
Application IDknyzzZnPSSxbmutMLUJ06w==
Document Descriptioninstallation user manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize34.22kB (427729 bits)
Date Submitted2010-03-02 00:00:00
Date Available2010-03-02 00:00:00
Creation Date2010-02-04 14:26:28
Producing SoftwarePDF-XChange 3.60.0112 (Windows XP)
Document Lastmod0000-00-00 00:00:00
Document Titleinstallation user manual

Installation and
Maintenance
TT1000
TT3000
TT4000
Version 1.3
e-DATA GmbH
01.2009 Version 1.3
1-1
1
1-2
Usage
1-3
1.1
Protection Class and Protection Type ................................... 1-3
1.2
Safety Measures ................................................................... 1-3
1.3
Before Commissioning .......................................................... 1-3
1.4
Operation .............................................................................. 1-3
1.4.1
Installation and Service ......................................................... 1-4
1.5
CE Conformance .................................................................. 1-4
1.6
FCC ...................................................................................... 1-5
Installation
2-6
2.1
Parts included ....................................................................... 2-6
2.2
Installation conditions............................................................ 2-6
2.3
Cable laying .......................................................................... 2-7
2.4
Device connection variants ................................................... 2-7
2.5
Mounting and connecting the TT3 device............................ 2-10
2.6
Shutdown mechanism......................................................... 2-12
2.6.1
Web-Interface for Administration......................................... 2-13
2.7
Cleaning the device ............................................................ 2-13
2.8
Repairs ............................................................................... 2-14
2.9
Guarantee........................................................................... 2-14
01.2009 Version 1.3
1
Usage
The device may only be used under those conditions and for
those purposes for which it has been designed.
1.1 Protection Class and Protection Type
The device conforms to the conditions of protection class IP30.
The device should only be run inside buildings.
1.2 Safety Measures
This device has been built according to the state-of-the-art and
the recognized technical safety rules and has left our works in
perfect condition. Improper handling and operation outside the
specified conditions can result in dangers due to electrical
current. This can endanger the lives of persons and damage
the machine.
1.3 Before Commissioning
Check the device for visible damage during transportation or
improper storage. Do not commission a damaged device!
The device may only be operated with AC voltage 110 to 240V
AC 50 to 60Hz.
1.4 Operation
Do not subject the device to any mechanical stresses such as
impacts, violent shaking or heavy loads. Impacts and shaking
can damage the electronics.
01.2009 Version 1.3
1-3
1.4.1 Installation and Service
The device should only be opened by suitably trained technical
personnel.
Before opening disconnect the device from the power source.
You should carry out repairs only in consultation with
e-DATA GmbH
1.5 CE Conformance
Safety requirements
This device is manufactured according to the safety
requirements of EN 60950.
Interference resistance
This device complies to the interference resistance criteria
according to EN 55024
Emitted interference
This terminal complies to the emitted interference criteria
according to:
EN 55022
EN 61000
Emitted interference
EN 55022
TT1000
EN 61000
CSA 60950 und FCC
1-4
01.2009 Version 1.3
1.6 FCC
This equipment complies with Part 15 of the FCC rules. Any changes or modifications not
expressly approved by the Manufacturer could void the user's authority to operate the
equipment. This device complies with Part 15 of the FCC rules subject to
thefollowing two conditions:
1. This device may not cause harmful interference
2. This device must accept all interference received, including interference that may
cause undesired operation.
NOTE:
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated
in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his own
expense.
01.2009 Version 1.3
1-5
2
Installation
Danger of current shocks!
The device should only be opened by suitably trained technical
personnel.
2.1 Parts included
1 device for Time & Attendance
1 wall mounting kit
2.2 Installation conditions
Surface wall installation with hidden screws. The cables are
fed on the back of the device under the plaster or as an
alternative from the bottom of the device.
Data lines to the higher or lower-level device are provided
by the customer.
If using the connection variant 2, i.e. connection cables from
the back, please ensure, that the in-wall connector is
located at the right position. See figure 5.3
The power supply is provided by the customer.
Security advice
To limit the input voltage of the device to overvoltage
category II the customer provides an appropriate
overvoltage protection unit!
Also an appropriate, easily accessible separator for the
power circuit is provided by the customer.
The power supply provided by the customer must use solid
conductors or a build-in power cable and a power outlet!
Possibly national regulations apply.
Network connections are only allowed within the same building!
2-6
01.2009 Version 1.3
Before mounting the device to the wall, please check the
following pre-conditions:
Clearance
Enough clearance must be available for mounting the device
(see casing dimensions in fig. 4.1).
Make sure enough clearance is available for the cables that
might be fed from the back.
2.3 Cable laying
General hints
Do not lay the data lines in parallel with cables that carry high
voltage. If this cannot be avoided, lay the lines in closed steel
tubes and keep a distance of 3 ft. for the protection from
electromagnetic influences.
2.4 Device connection variants
Connection variant 1
TT3000 und TT4000
For this variant a fix built-in power cable to be connected to a
wall outlet is used. The connection cables for the device can be
plugged in at the bottom side of the device.
The connectors COM1 and COM3 can only be reached from
beneath.
COM1/
Console
COM3
ISDN/
Modem
ETH
Built-in
power cable
length 1,50 m
(5 ft)
100 ... 240V AC
Figure 5.1 Connections TT3 bottom side
01.2009 Version 1.3
2-7
Connection variant 2
For this variant there is no preinstalled power cable. The
connection cables including power can be plugged in from the
back through a hole in the back plate.
TT3000 und TT4000
The IO clamp can only be reached from the back.
pluggable clamp
power
ground wire
USB
ETH
pluggable clamp
IO
Connections TT3000 / 4000 back side
Power cable
LAN Ethernet cable
ground wire
2-8
01.2009 Version 1.3
Attention!
The ground wire is to be fixed to the metal housing with a
screw-type clamp!
Connection variant 3
The connection cables including power can be plugged in from
the bottom before final mounting.
TT1000
Always connect protective conductor
Back side
Always connect protective conductor
01.2009 Version 1.3
2-9
2.5 Mounting and connecting the TT3 device
Attach the wall mounting kit with four countersunk screws (Ø
max. 0.2 in (5mm)) to the wall. The recommended height of
the upper holes is 4.0 ft (1.2 m) (display height).
Wall
mounting kit
In-wall
connector
1,20 m (4 ft)
1,12 m (3,6 ft)
Wall mounting
Mounting steps
1. Mark drill holes by using the wall mounting kit as a
template.
2. Drill four holes for the screws. If necessary use screw
anchors.
3. Mount the wall mounting kit with four screws.
2-10
01.2009 Version 1.3
Figure. 5.3.1 Mounting the TT3 wall mounting kit
If using the connection variant 2, i. e. connection cables
from the back, connect the power cable and the Ethernet
cable now. The ground wire is connected to the metal
housing.
4. Insert the terminal back plate slots into the wall
mounting kit top hooks and lower.
5. Attached the terminal back plate to the bottom of the
wall mounting kit with 2 screws .
01.2009 Version 1.3
2-11
Mounting the back plate
If using connection variant 1, i. e. built-in power cable, plug in
the Ethernet and power cables now.
Note
Devices with rechargeable batteries may be only partially
loaded at the time of delivery. They provide full power only after
an appropriate loading phase!
2.6 Shutdown mechanism
Without battery
If the device is disconnected from the mains power supply
“power off” is recognized. For a few seconds an internal
emergency power source on the mainboard provides the device
with power. A “power off” message is sent to the host CPU,
which performs a shutdown as fast as possible. A shutdown
execution message is sent to the mainboard, which is then
switched off completely. Also if the device is removed from the
wall without being disconnected from the power supply, a light
barrier interrupt message is sent to the host CPU. Again the
host CPU performs a fast shutdown und sends an execution
message to the mainboard. But in this case the device will not
be switched off completely, but stays in a HALT state (display
shows “Halting device”).
If in this state the power supply is disconnected, the device is
switched off immediately.
2-12
01.2009 Version 1.3
With rechargeable battery If mains “power off” is recognized, the device switches to
battery operation. The new state is sent to the host CPU and (if
the battery is loaded) nothing else happens.
If in this state the device is removed from the wall, a light barrier
interrupt message is sent to the host CPU. The host CPU
performs a fast shutdown und sends an execution message to
the mainboard. The mainboard turns off the battery, thus
switching off the device.
Also if the device is removed from the wall without being
disconnected from the mains power supply, a light barrier
interrupt message is sent to the host CPU. Again the host CPU
performs a fast shutdown und sends an execution message to
the mainboard. But in this case the device will not be switched
off completely, but stays in a HALT state (display shows
“Halting device”).
If in this state the mains power supply is disconnected, the
device is switched off immediately (without using the battery).
2.6.1 Web-Interface for Administration
For accessing the webinterface of the terminal, please point
your browser to the
http://terminal-ip-adress e.g http://192.168.0.100 of the terminal.
Choose your language and enter with the password “admin”
Danger of current shocks!
Disconnect the device from the power source before opening!
2.7 Cleaning the device
01.2009 Version 1.3
2-13
Organic solvents and scouring agents can damage the device.
Clean the device with a moist, non-fluffing cloth.
2.8 Repairs
Repairs may only be carried out by permission of
Timelink International.
Repairs must be carried out professionally. Only original
components may be used as spare parts.
2.9 Guarantee
The elements of guarantee are established by legal regulation.
e-DATA GmbH
Mollenbachstrasse 19
D-71229 Leonberg
Germany
Phone 0049(0) 71 52 93979 -0
Fax 0049(0) 71 52 93079 -50
Installation and Maintenance TT Devices
Version 1.3
Copyright 2009 e-DATA GmbH
This manual is protected. Reproduction or translation of the
manual or its transmission on other electronic media, even in
extract form, is only allowed with the express written permission
of e-DATA GmbH
e-DATA GmbH reserves the right to make changes to the user
manual without prior notice.
e-DATA GmbH does not accept any liability whatever for direct
and indirect damage, especially loss of data, that result from the
usage of the device, the software or the manual!
2-14
01.2009 Version 1.3

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Producer                        : PDF-XChange 3.60.0112 (Windows XP)
Create Date                     : 2010:02:04 14:26:28+01:00
Page Count                      : 14
EXIF Metadata provided by EXIF.tools
FCC ID Filing: WIWTT1000

Navigation menu