goodbetterbest EX1RT EX1-R Bluetooth Headset with NC User Manual
Goodbetterbest Limited EX1-R Bluetooth Headset with NC Users Manual
Users Manual
EX1-RT
BLUETOOTH
HEADSET
INSTRUCTION
MANUAL
FITTING YOUR HEADSET
CONNECTING TO YOUR PHONE
SEARCH
FOR NEW
DEVICES
ENTER
PASSKEY
0000
(FOUR ZEROS)
TURN ON
BLUETOOTH
SELECT
EX1-RT
‘HOLD’
POWER BUTTON
3 4 5
2
1
3s
EX1-RT
Volume Decrease / Mute
Volume Increase
Power / Answer /
Reconnect
POWER ON : Hold for 2 secs
until all LED’s turn Red.
[Voice Prompt: Power On]
POWER OFF : Hold for 3 secs
until LED turns Red, then o.
[Voice Prompt: Power O]
TAKE A CALL : Press once.
REJECT A CALL : Hold 2 secs.
END A CALL : Press once.
REDIAL : Press twice.
(Re-dialing is only available for the
first device if two are connected.)
VOICE-DIALING :
Press once then say ‘Call’
along with the name of the
person you want to ring.
(Voice Dialing is only available for the
first device if two are connected.)
For further details on voice dialling,
refer to your phone manual).
CALL-WAITING
END CURRENT CALL :
Press once.
PUT CURRENT CALL ON HOLD :
Hold for 2 seconds.
This can also be used during
multi-connection of 2 devices.
LOW BATTERY
All LED’s will flash Red
once every minute.
[Voice Prompt: Battery Low]
VOLUME INCREASE
Tap to increase the volume
in increments.
VOLUME DECREASE
Tap to decrease the volume
in increments.
MUTE
Hold down for 2 seconds.
A tone will sound every 10
seconds when in mute mode.
Repeat to un-mute.
IMPORTANT:
Please ensure you read the
‘For your Safety’ section
before using this product.
For technical assistance:
www.gioteck.com/
contact-support
FUNCTIONALITY
DISTANCE
The EX1-RT headset has a range up to
10 metres (33 ) from a device before
audio degrades or loses connection.
LESS THAN
10M / 33FT
Complies with
IDA Standards
DB100398
The Bluetooth word mark and
logos are owned by the Bluetooth
sig, inc. and any use of such marks
by Gioteck is under licence.
Charging indication will be delayed if the
headset has not been used for a long time.
The Power LED will be red during charging
and all LED’s will light when charged.
CHARGING
2h
EN
CONNECTING DEVICES
If pairing is not completed within 2 minutes the headset will
turn o. If this happens, please repeat the pairing process.
MULTI-CONNECTION TO 2 DEVICES
Follow the instructions above to pair the EX1-RT to 2 devices.
Switch the headset o and on again, and it will connect to
both devices automatically. When the headset is turned on,
it will connect to the last device you were connected to.
STREAMING AUDIO
Audio will stream automatically once the EX1-RT is wirelessly
connected to a device. Streaming will pause during an
incoming/outgoing call and resume when the call ends.
To use the headset for the first time you must
pair it with a Bluetooth® enabled device.
1. Ensure the headset is within 1 meter of the device.
2. Activate Bluetooth on the device (Settings >Bluetooth > ON)
3. With the EX1-RT O, hold the Power button for 3 secs until
all the LED’s illuminate to a solid state. [Voice Prompt: Pairing ]
4. Select ‘EX1-RT’ from the list of Bluetooth devices,
or select ‘Scan for new devices’.
5. If the device asks for a passcode, enter four zeros (0000).
6. The LEDs will flash every 3 seconds once pairing is successful.
[Voice Prompt: Pairing Successful] [Voice Prompt: Phone Connected]
The headset will now connect to your device automatically.
The headset will turn o automatically
aer 10 minutes of inactivity.
EN
Exposure to high volume
sound levels may cause
temporary or permanent
damage to your hearing.
You should always set your
volume to moderate levels
and avoid long exposure
to high volume levels.
Please help to conserve
the environment by
recycling the packaging
of this product.
This product should NOT
be disposed of in normal
household waste. Please
take it to an electrical
waste collection point.
FOR YOUR SAFETY
To help ensure risk-free operation
please read these Operational and
Safety Guidelines before use:
• Contains small parts. Not suitable
for children under 3 years of age.
• Store in a dry and dust free area.
• Do not store in areas of
extreme low (0°C) or high
(40°C) temperatures.
• Avoid direct sunlight
and heat sources.
• Do not allow the product
to get wet or dirty; doing
so may cause damage.
• Do not clean with benzene,
paint thinner, acetone, alcohol,
or other such solvents.
• Do not take the product apart;
doing so will void your warranty
and may cause electrical shock or
damage to internal components.
• Do not allow the battery or
battery compartment to
get into contact with metal
objects such as keys or coins.
• Charge the product as specified
and only use the charger supplied.
• Avoid charging the product
while unattended.
• Check local laws regarding
using a headset while driving.
• Keep earbuds clean and
free of ear wax to maintain
product performance.
This product is covered by a
one [1] year warranty. For full
Terms and Conditions, and for
Technical Assistance, go to :
www.gioteck.com/
contact-support
a Class B digital device, pursuant
to part 15 of the FCC Rules.These
limits are designed to provide
reasonable protection against
harmful interference in a residential
installation. This equipment generates,
uses and can radiate radio frequency
energy and, if not installed and used
in accordance with the instructions,
may cause harmful interference to
radio communications. However, there
is no guarantee that interference will
not occur in a particular installation.
If this equipment does cause harmful
interference to radio or television
reception, which can be determined
by turning the equipment o and
on, the user is encouraged to try to
correct the interference by one or
more of the following measures:
• Reorient or relocate the
receiving antenna.
• Increase the separation between
the equipment and receiver.
• Connect the equipment
into an outlet on a circuit
dierent from that to which
the receiver is connected.
• Consult the dealer or
an experienced radio/
TV technician for help.
This equipment complies with FCC
radiation exposure limits set forth
for an uncontrolled environment.
End user must follow the specific
operating instructions for satisfying
RF exposure compliance. This
transmitter must not be co-located
or operating in conjunction with any
other antenna or transmitter.
This device complies with Industry
Canada RSS 210 standard(s).
Operation is subject to the following
two conditions: (1) this device may
not cause interference, and (2) this
device must accept any interference,
including interference that may cause
undesired operation of the device.
Le présent appareil est conforme aux CNR
d’Industrie Canada applicables aux appareils
radio exempts de licence. L’exploitation est
autorisée aux deux conditions suivantes : (1)
l’appareil ne doit pas produire de brouillage,
et (2) l’utilisateur de l’appareil doit
accepter tout brouillage radioélectrique
subi, même si le brouillage est susceptible
d’en compromettre le fonctionnement.
Gioteck hereby declares that
this product is in compliance
with the essential requirements
and other provisions of Directive
2004/108/EC and R&TTe 1999/5/
EC. To view the full version of the
Declaration of Conformity please
go online to doc.gioteck.com
Caution: The user is cautioned that
changes or modifications not expressly
approved by the party responsible
for compliance could void the user’s
authority to operate the equipment.
This device complies with Part 15 of
the FCC Rules. Operation is subject
to the following two conditions: (1)
this device may not cause harmful
interference, and (2) this device must
accept any interference received,
including interference that may
cause undesired operation. Note:
This equipment has been tested and
found to comply with the limits for
LEGAL
This product complies with the following legal regulations.
For further information go to www.gioteck.com
Technical Assistance:
gioteck.com/contact-support