iControl Networks IHUB3000B Home Monitoring Gateway User Manual Cover Install

Download:
Mirror Download [FCC.gov]
Document ID	1325360
Application ID	BXNmtoRSc7G8fkKUU2sV9A==
Document Description	User manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	54.28kB (678488 bits)
Date Submitted	2010-08-11 00:00:00
Date Available	2010-08-11 00:00:00
Creation Date	2010-04-14 09:54:17
Producing Software	Acrobat Distiller 8.0.0 (Windows)
Document Lastmod	2010-07-23 15:39:46
Document Title	Cover___Install
Document Creator	Acrobat PDFMaker 8.0 for Word
Document Author:	MadCap Software

iHub‐3000B
Installation Guide
When used with the
Concord 4 Security Panel
Installation Guide for the iHub‐3000B‐ADT and the Concord 4 Security Panel
Copyright © 2010 ADT Security Service, Inc. All rights reserved.
About This Guide
This document does not cover the physical installation and special configurations that may be required
for the security system components. Refer to the manufacturer's documentation for each device for
those specifics.
Overview of the Installation Process
The installation utilizes a streamlined process for setting up the system. All components are individually
activated and tested before being physically installed in their final locations, whenever possible.
Installation Guide for the iHub‐3000B‐ADT and the Concord 4 Security Panel
Activating the Service with Concord 4 Security Panel
Before you begin the activation process, you must make some hardware connections. Since each
security panel is different, follow the instructions in the next section, "Connecting the Hardware", for
the specific security panel you are installing. Then please follow the instructions in "Activating the
Service" on page 3 for all security panels.
Connecting the Hardware
Follow the procedure in this section that applies to the security panel you are installing.
Note:
Do not connect the iHub gateway's power supply to an electrical outlet until you
are instructed to do so by the activation wizard. If you power on the gateway before it is
connected to the Internet, it cannot retrieve the information it requires on power up. If you
have already done this, simply unplug it and continue with the following instructions.
If you are installing a Touch Screen, do not connect it to a power source until you are
instructed to do so by the activation wizard.
To connect the gateway to the Concord 4 security panel:
1. Wire the Automation Module to the Concord's bus, as described in the GE Installation Manual.
2. Gateway model iHub‐3000B‐ADT, connectors are labeled Tx+, Tx‐, Rx+, and Rx‐. The automation
module connectors are labeled the same but might include a/b instead of +/‐. Using a standard 4‐
wire security cable, connect the ports on the gateway's RS422 bus to the Automation Module as
follows:
Gateway
Automation Module
Tx+
Rx+ or Rxb
Tx‐
Rx‐ or Rxa
Rx+
Tx+ or Txb
Rx‐
Tx‐ or Txa
Do not connect any antenna provided to the port on the gateway labeled Cellular. Cellular
communications from the iHub are not used.
Activating the Service
To activate the service:
1. On a computer connected to the Internet, open a web browser, and go to the activation URL
portal.adtpulse.com/activation.
2. Enter your username and password, and click Sign In.
The activation wizard displays the Welcome screen.
Installation Guide for the iHub‐3000B‐ADT and the Concord 4 Security Panel
3. After reading the information on the screen, click Continue.
The Select Hardware screen appears.
4. Select the type of hardware you are installing, and click Continue.
The Enter Activation Key screen appears.
Installation Guide for the iHub‐3000B‐ADT and the Concord 4 Security Panel
5. Enter the activation key, and click Continue.
Note:
The activation key contains numbers from 0‐9 and letters from A‐F.
There are no letters O or I.
The activation process begins, and then the Select Service Options screen appears.
6. Select the appropriate options for the installation based on the information on the Installer
Reference Sheet, and click Continue.
The Physical Setup screen appears. The exact wording on this screen varies based on the security
panel you are installing and the service options you selected on the previous screen.
Installation Guide for the iHub‐3000B‐ADT and the Concord 4 Security Panel
7. Follow the instructions on the screen, and then click Continue.
A message displays a progress bar, which indicates approximately how much longer the activation
will take. If an upgrade is required, the activation application performs the upgrade automatically.
If the power light blinks amber, it indicates that an upgrade is in process.
Installation Guide for the iHub‐3000B‐ADT and the Concord 4 Security Panel
Assigning the Site Owner
The next step in the procedure is to set the site owner, configure the site settings, and sign in to the web
portal to complete the installation process. The user selection screen should still be displayed on the
computer. This screen offers the option of creating a new user account or using an existing user account.
Take one of the following actions:
If the customer does not have a user account, click Create New User Account. The Create User
Account screen appears. Continue with "Creating a User Account" on page 7.
If the customer already has a user account, enter their username on the right side of the screen,
and click Continue. Skip the next section and continue with "Configuring Site Information" on
page 8.
Creating a User Account
For customers who do not yet have a user account, you must create one. The user account enables you
to complete the installation process and then for the customer to access their security system online or
from a mobile device anytime they want. (If the customer already has a user account, skip this section.)
To create a new user account:
1. On the Activate Service sign in screen, click Create New Account.
The Create User Account screen appears.
Installation Guide for the iHub‐3000B‐ADT and the Concord 4 Security Panel
2. Enter the required information for the customer.
Enter the username that the customer prefers. Depending on how your the system is configured,
the username might be restricted to a certain number of characters.
3. Click Continue.
The Site Information screen appears. Continue with "Configuring Site Information" on page 8.
Configuring Site Information
When you click Continue on either the user selection screen or the Create User Account screen, the Site
Information screen appears.
Installation Guide for the iHub‐3000B‐ADT and the Concord 4 Security Panel
Note:
Depending on how the system is configured, this screen might not require you
to enter all of the information shown in this example.
To configure the site information:
1. Enter the required information from your Installer Reference Sheet, and then click Next.
Note:
The Security Panel User Access Code must match the same access code in the
ADT Pulse portal. For example if the user access code is 1234 (not recommended), the ADT
Pulse setting must also be 1234 or remote control will not be possible.
The installer should inform the customer that if they ever change their keypad user code
they must also change the code in the ADT Pulse web portal.
A message informs you that the service is now active.
Note:
If the service is not successfully activated, please refer to the Pulse
Troubleshooting guide for help.
2. Click Go to Portal.
The installer sign in page appears.
Installation Guide for the iHub‐3000B‐ADT and the Concord 4 Security Panel
3. Enter your installer password in the Installer Password field, and click Sign In.
The web portal launches and displays a site status message at the top of the page indicating that
the site is in install mode.
4. If you have not yet installed the security sensors, continue with "Adding GE Security Sensors and
Remotes" on page 13. If you have already installed the sensors, continue with the next section.
Note:
If you click Run Diagnostics, it launches the Site Diagnostics Tool. (Refer to the
separate documentation for that internal tool.)
Note:
10
To reset an inclusion controller, follow the manufacturer's instructions.
Installation Guide for the iHub‐3000B‐ADT and the Concord 4 Security Panel
Specifications, Approvals and Certifications.
Ethernet
Wireless
Wired Control
Interface
Software
Hardware
LAN
1 (10/100 Mbit/sec port)
WAN
1 (10/100 Mbit/sec port)
WiFi
IEEE 802.11b/g
Z-Wave
Built-in Z-Wave module
RS422
1 (External RS422 by screw terminal connector)
USB
2 (for future expansion)
JTAG
1 (for development / debug)
Applications
Linux 2.4 BSP Ready
Web Browsers
Broadcom BCM5354 Web Interface
Processors and
memory
SoC: Broadcom 5354
SDRAM: DDR 32 MB
Nor Flash 32 MB
LED and Button
LED: Power, Broadband, Devices Antenna
Button: Reset, Sync
1 WiFi Dipole antenna
1 Z-Wave internal antenna
Power
Consumption
12 DC, Max 10.5W
Compliance
FCC, CA
Power Supply: UL
Dimensions
(H x W x D)
235 x 160 x 40mm
(9.3" x 6.3" x 1.57")
Weight
590g (1.3 lb)
Connectors
DC Power Jack
Screw Terminal for RS422
2 RJ-45 for Ethernet LAN and WAN
2 USB for external USB device
Environment
Operation: Temperature: 0 - 40°C (32° - 104°F); Humidity: 10% - 80% RH (non-condensing)
Storage: Temperature: -20 - 70°C (-4° - 158°F); Humidity: 0% - 90% RH (non-condensing)
Accessories
Powered Supply (12V / 1A, 100-240VAC)
11
FCC Warning statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC
rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void your
authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may
not cause harmful interference and (2) this device must accept any interference received, including interference that may cause
undesired operation
FCC RF Radiation Exposure Statement:
1.
This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
2.
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment
should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body.
IC RF Radiation Exposure Statement:
1. This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
2. This equipment complies with IC RF radiation exposure limits set forth for an uncontrolled environment. This equipment
should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body.
IC Warning statement
RSS-GEN 7.1.5:
Operation is subject to the following two conditions: (1) this device may not cause interference,
and (2) this device must accept any interference, including interference that may cause undesired
operation of the device.
RSS-GEN 7.1.4:
User Manual for Transmitters with Detachable Antennas
The user manual of transmitter devices equipped with detachable antennas shall contain the
following
information in a conspicuous location:
This device has been designed to operate with the antennas listed below, and having a maximum
gain of [5] dB. Antennas not included in this list or having a gain greater than [5] dB are
strictly prohibited for use with this device. The required antenna impedance is [50] ohms.
RSS-GEN 7.1.5
To reduce potential radio interference to other users, the antenna type and its gain should be so
chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that permitted
for successful communication.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Encryption                      : Standard V1.2 (40-bit)
User Access                     : Print, Fill forms, Extract, Assemble, Print high-res
Create Date                     : 2010:04:14 09:54:17+08:00
Modify Date                     : 2010:07:23 15:39:46+08:00
Company                         : MadCap Software
Source Modified                 : D:20100413214523
Tagged PDF                      : Yes
Producer                        : Acrobat Distiller 8.0.0 (Windows)
Mod Date                        : 2010:07:23 15:39:46+08:00
Creation Date                   : 2010:04:14 09:54:17+08:00
Author                          : MadCap Software
Creator Tool                    : Acrobat PDFMaker 8.0 for Word
Metadata Date                   : 2010:07:23 15:39:46+08:00
Document ID                     : uuid:09730964-720b-42c4-a298-17d6f0977bf3
Instance ID                     : uuid:c9296b84-78f0-449d-8a76-9d851b1c1e7a
Subject                         : 2
Format                          : application/pdf
Creator                         : MadCap Software
Title                           : Cover___Install
Has XFA                         : No
Page Count                      : 12
Page Layout                     : OneColumn

EXIF Metadata provided by EXIF.tools