iDevices IDEV0020 Battery Powered Bluetooth Enabled Wireless Switch User Manual 15 IDEV0020 UserMan

iDevices, LLC Battery Powered Bluetooth Enabled Wireless Switch 15 IDEV0020 UserMan

15_IDEV0020 UserMan

1INSTALLATION AND SETUP GUIDEiDEVICES SMART HOME SOLUTIONS
2REQUIRES• A Compatible iDevices® Product• iDevices® Connected app• Controlling This Product Requires An iPhone, iPad, Or iPod Touch With iOS 8.1 Or Later• Android™ 4.3+ Device With Bluetooth® TechnologyWHAT’S INCLUDED• iDevices® Instant Switch With CR2032 Battery (Pre-Installed)• iDevices® Faceplate• Includes Command® Strips from 3M (1)• Ground Wire AssemblyTOOLS NEEDEDWhen installing into a gang box, you will need the following tools:• Philips Screwdriver• Flathead Screwdriver RATINGS3 VDC, 5.4mAReplacement Battery: CR2032
3• The iDevices® Instant Switch must be installed in a manner that conforms to all applicable national, state, and local building codes.• When installing with Command® Strips from 3M, do not install above a bed, onto wallpaper, or outdoors.• The iDevices® Instant Switch is intended for dry, indoor use only. • Ambient operating conditions: 32º F to 104º F (0º C to 40º C), 0-90% humidity, non-condensing.• The iDevices Instant® Switch uses 1 CR2032 coin cell battery. Do not use a rechargeable battery. Using an improper battery may damage the iDevices® Instant Switch. Please dispose of this battery at a recycling  facility.Contactyourlocalwastedisposalprovidertondarecyclecenterlocationnearestyou. CAUTION: Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to the instructions. !
4BEFORE YOU START• Visit our YouTube channel for tips on installation and setup: www.YouTube.com/User/iDevicesInc• Wherever possible, install the iDevices® Instant Switch in a non- metal gang box and use a non-metal/metallic faceplate, as metal gang boxes and faceplates can decrease the Bluetooth® signal strength.• Check that your mobile device is compatible with the iDevices® Instant Switch at iDevicesinc.com/Compatibility• It is YOUR responsibility to be sure that products are installed in accordance with applicable building codes. Check with your local  buildingofceifyouhavequestions.
5• The iDevices® Instant Switch requires an existing iDevices product to function. Find additional products at iDevicesinc.com/Store• Download the free iDevices® Connected app.
6GETTING TO KNOW THE iDEVICES® INSTANT SWITCH123Turn Light On/Increase Brightness. (Note: Dimmable feature only available when paired to a dimmable iDevices® product). Single tap to turn light on. Press and hold to increase brightness level. Double tap to quickly increase light to maximum brightness.Turn Light Off/Decrease Brightness. (Note: Dimmable feature only available when paired to a dimmable iDevices® product). Single tap to turn light off. Press and hold to decrease brightness level. Double tap to quickly decrease light to minimum brightness level.Status LED. Provides setup status. Refer to LED color codes on page 20.
76742575433M Command™ Strip Access Door. Remove to access 3M Command™ Strip when removing Instant Switch from wall.Level. Built-in level ensures exact installation.Switch Unit Removal. Press sides to remove Switch from mounting plate to access battery.Pairing Reset. Press and hold for 10 seconds, until LED blinks red.Device Reset. Press and hold 7+1 simultaneously for 10 seconds, then release to cycle power to the device.+7 116
8GETTING TO KNOW THE iDEVICES® INSTANT SWITCH (CONT.)8Ground Wire Assembly. Connect to Instant Switch when installing into a gang box.
988
10USING FOR THE FIRST TIMEREMOVE BATTERY PULL TABBefore using the iDevices®InstantSwitchforthersttime,youwillneed to remove the battery tab. Pull the plastic tab out of the back of the product and discard.
11
12INSTALLATION METHODSThere are 3 methods in which you may install your Instant Switch: By itself on the wall, using the provided 3M Command™ Strip and iDevices® faceplate or a standard rocker faceplate of your choice. Next to an existing gang box, using the provided 3M Command™ Strip and a multiple switch faceplate of your choice (not included). Installed directly into a gang box using a standard rocker style faceplate (not included).Whichever method you choose, ensure your iDevices® Instant Switch is installed perfectly by using the built-in level.123
13
14INSTALLATION INSTALL ON A WALL•TomountyourInstantSwitchdirectlyontoawall,rstthoroughly clean the wall’s surface with isopropyl alcohol to remove any dirt or dust. • Remove the plastic backing to the Command™ Strip & align the strip with the recessed area on the back of the Instant Switch. • Peel off the other side of the plastic backing and ensure that the  productislevelbeforepressingrmlytothewallfor30seconds.• Install the magnetic iDevices® faceplate, or a rocker style faceplate of your choice.1
15
16 INSTALL NEXT TO GANG BOX• Mount to the wall using the 3M Command™ Strip next to an existing gang box, as directed on page 14. • Install a multiple rocker switch faceplate (not included) directly over the Instant Switch and the existing switches to create a multi- switch grouping. 2
17
18 INSTALL INTO GANG BOX• Turn OFF the power to the circuit you are working on at your home’s breaker or fuse panel. • Install the Ground Wire Assembly onto the access door of the Instant Switch.3
19
20 INSTALL INTO GANG BOX (CONT.)• Connect the ground wire on the Instant Switch to the ground wire in the gang box, which is usually bare cooper or green.3
21GROUND(Usually Bare Copper or Green)
22 INSTALL INTO GANG BOX (CONT.)• If you choose this method of installation, do not use the 3M Command™ Strip on the back of the product. Instead, use the screws provided to anchor it into the gang box. • Install a rocker switch faceplate (not included). • Turn the power back on at your circuit breaker. CAUTION: It is not intended to use the iDevices® faceplate when mounting the iDevices® Instant Switch in a gang box. Instead, use a standard rocker faceplate of your choice (not included). !3
23
24BATTERYREPLACING BATTERY• The iDevices® Instant Switch uses a standard CR2032 battery, and lasts up to 2 years. • Access the battery by pressing the module assembly in where noted and tilting the top toward you to remove from the mounting plate. • After the module assembly has been removed, the battery will be visible on the back. •Removethebatterybyinsertingyourngerintothenotchand pulling it toward you. CAUTION: Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to the instructions. !
25
26REPLACING THE MODULE ASSEMBLY• Line up the tabs on the bottom of the module assembly with the arrows on the bottom of the mounting plate. •Tipthetopofthemoduleassemblyupandpressitrmlyuntilit clicks into place.
27
28REMOVING YOUR WALL MOUNTED INSTANT SWITCH• Remove the Access Door to expose the end of the 3M Command® Strip. • Pull straight down on the end of the 3M Command® Strip, while  holdingInstantSwitchrmlyagainstthewall. NOTE: Be sure to pull straight down, as pulling at an angle risks breaking the 3M Command® Strip.
29
30REFERENCE INFORMATION LED COLOR CODES LED State Instant Description Blue Flash Instant Switch is in pairing mode. The LED ashes blue.Solid Blue Pairing mode has been completed. The LED will turn solid blue. Green FlashWhen the product setup or software update is complete, the LED ashes green 5 times.Solid Yellow On button press, if battery is low, the LED will turn solid yellow for 2 seconds.
31LED State Instant DescriptionRed FlashOn button press, if battery needs replacement, the LED will rapidly ash red 5 times.Solid RedOn button press, if Instant Switch has lost the link with it’s paired iDevices product, the LED will turn solid red for 5 seconds.Purple Flash When Instant Switch is performing a software update, it ashes purple.
32SUPPORT If at any time you require assistance, please contact our Customer Experience Team. 888.313.7019 Support@iDevicesinc.com iDevicesinc.com/Support
33TROUBLESHOOTING AND SUPPORT A DEVICE RESET CAN RESOLVE MOST ISSUES. Device Reset. Press and hold 7+1 simultaneously for 10 seconds, then release to cycle power to the device.+7 1
34REGULATORY INFORMATION Product Information:Manufacturer: iDevices® LLCModel: IDEV0020FCC: 2ABDJ-IDEV0020IC: 11569A-IDEV0020The iDevices®InstantSwitchIDEV0020iscertiedtocomplywithapplicableFCC and IC rules and regulations governing RF and EMI emissions. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
35FCC Notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
36• Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.• Consult the dealer or an experienced radio/TV technician to help. • Changesormodicationsnotexpresslyapprovedbythepartyresponsible for compliance could void the user’s authority to operate the equipment.IC Notice This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout
37brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement. This device complies with the Industry Canada license exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.CAUTION: To Reduce the Risk of Overheating And Possible Damage To Other Equipment, Do Not Install To Control A Receptacle, A Motor-Operated Appliance, A Fluorescent Lighting Fixture, Or A Transformer-Supplied Appliance.
38ATTENTION:AnDeReduireLeRisqueDeSurchauffeEtLaPossibiliteD’Endommagement A D’Autres Materiels, Ne Pas Installer Pour Commander Une Prise, Un Appareil A Moteur, Une Lampe Fluorescente Ou Un Appareil Alimente Par Un Transformateur.ReferencesRequires the iDevices® Connected app. For warranty information please visit iDevicesinc.com/Warranty. Apple, the Apple logo, iPhone, and iPod touch are trademarks of Apple Inc., registered in the U.S. and other countries. App Store is a service mark of Apple Inc. Android is a trademark of Google Inc. Google Play and the Google Play logo are trademarks of Google Inc. The Bluetooth® word mark and logos are registered trademarks owned by the Bluetooth SIG, Inc. and any use of such marks by iDevices® is under license. Other trademarks and trade names are those of their respective owners.
39
40iDevicesinc.com

Navigation menu