iDevices OUTLET In-wall On/Off Smart Outlet User Manual 15 IDEV0010 UserMan

iDevices, LLC In-wall On/Off Smart Outlet 15 IDEV0010 UserMan

UserManual.wiki >

OUTLET User Manual

15_IDEV0010 UserMan

1INSTALLATION & SETUP GUIDEIN WALL SOLUTIONS

2 3REQUIRES• Wi-Fi® 2.4 GHz 802.11 b/g/n compatible network • Router Security Settings Supported: WPA, WPA2, or None • Free iDevices® Connected App• 120VAC “Line” and “Neutral” wires in each gang box• HomeKit requires an iPhone, iPad or iPod touch with iOS9 or later• Android™ 4.3+ devices with Bluetooth® Smart technologyNOTE: 5 GHz networks are not compatible.• Not intended for critical medical or life support equipment.• Use caution when using the iDevices® Wall Outlet to control any appliances which produce heat or mechanical motion, or could create a hazardous condition when operated while unattended. • The iDevices® Wall Outlet is not user-serviceable. Do not attempt to open the enclosure for any reason.• The iDevices® Wall Outlet is only for installation with copper or copper-clad wires. Do not install in a circuit that uses aluminum wires.• The iDevices® Wall Outlet must be installed in a manner that conforms to all applicable national, state, and local building codes.• The iDevices® Wall Outlet is intended for dry, indoor use only. • The iDevices® Wall Outlet is not a Ground Fault Circuit Interrupt (GFCI) or Arc Fault Circuit Interrupt (AFCI) protected outlet.• The iDevices® Outlet should be installed in a circuit with a breaker/fuse rated at no more than 15 Amps. The total load (both receptacles combined) should not exceed 1800W. RISK OF ELECTRIC SHOCK, SEVERE BURNS, AND FIRE: Your safety is important to us. Electricity is dangerous and can cause personal injury and property damage if handled improperly. A working knowledge of electrical installation is required to install this product. If you are not comfortable working with electricity do not attempt to install the iDevices® Wall Outlet and seek professional assistance from a qualied electrician.!TOOLS NEEDED• Philips Screwdriver• Pliers• Wire Cutter/Stripper• Voltage Detector• Flathead ScrewdriverRATINGSInput: 125VAC, 60HzOutput: 125VAC, 60HzTungsten: 600W (5A)General Use: 1800W (15A)Motor: 1/2 HPResistive: 1800W (15A)

4 5BEFORE YOU START • Read through this Installation Guide in its entirety before starting installation of your iDevices® Wall Outlet or removal of your old outlet. Incorrect installation can be dangerous and can damage your iDevices® Wall Outlet or your home. • Visit our YouTube channel for tips on installation and setup: www.youtube.com/user/iDevicesInc• Turn OFF the power to the circuit you are working on at your home’s breaker or fuse panel. • Where ever possible, install the iDevices® Wall Outlet in a non- metallic gang box and use a non-metallic faceplate, as metal gang boxes and faceplates can decrease the Wi-Fi® signal strength. • Check that your mobile device is compatible with the iDevices® Wall Outlet at iDevicesinc.com/Compatibility • It is YOUR responsibility to be sure that products are installed in accordance with applicable building codes. Check with your local building ofce if you have questions.• Download the Free iDevices® Connected app.

6 7GETTING TO KNOW THE iDEVICES® WALL OUTLETTop Outlet On/Off. Pressing this button will turn the individual outlet On or Off. DEVICE RESET: Press and hold for 10 seconds until LED blinks red. PAIRING MODE: Press and hold for 3 seconds until LED is solid blue.Bottom Outlet On/Off. Pressing this button will turn the individual outlet On or Off. DEVICE RESET: Press and hold for 10 seconds until LED blinks red. PAIRING MODE: Press and hold for 3 seconds until LED is solid blue.Status LED/Night Light. Provides setup status and used as a night light during operation. Refer to LED color codes on page 16.Pull Out Tab. Refer to this when prompted to enter your HomeKit™ code during the setup on a iOS device.Device Reboot. Pressing this cycles power to the entire unit.1144225533

8 9INSTALLATION STEP 1Take a photo of your existing wiring for future reference. Turn off the power to the circuit at your breaker or fuse panel. If you are replacing an existing outlet, verify that the outlet no longer has power before proceeding.*STEP 2 Wire the receptacle in place of an existing receptacle according to the adjacent diagram with the provided wire nuts. Ensure the wire nuts are fastened securely.*If the outlet is in a multiple-gang box (with two or more switches and/or outlets), make sure that all circuits in the gang box are turned off at the breaker or fuse panel.WHITE NEUTRALBLACKCOPPERLINEGROUND

10 11STEP 3 Secure the iDevices Wall Outlet back into the gang box.STEP 4 Turn the power back on at the breaker. If the outlet is connected properly, you should see the LED indicator rapidly ash blue to indicate the unit is ready to connect to the app. LED will rapidly ash blue when it’s ready to connect to the app.

12 13CONNECTING TO YOUR NETWORKIDEVICES® CONNECTED APP Download the iDevices® Connected app and connect to your home’s Wi-® network. To proceed with setup please be sure both Wi-® and Bluetooth® are enabled on your device. One Color IconBasicConnected App IconOptimized Small Versions.75pt Additional .5pt AdditionalLED will rapidly ash blue when it’s ready to be paired.12POWER ON OUTLET Ensure the Power/Breaker is turned back On and the LED on the iDevices® Wall Outlet is rapidly ashing blue. Note: If the LED is not ashing blue rapidly, hold either of the On/Off buttons until the LED blinks red, then release to perform a Device Reset and re-enter pairing mode. At this point, the LED will rapidly ash blue.

14 15CONNECT OUTLET Launch the iDevices® Connected app and you will be guided through the process of connecting your Wall Outlet. For iOS devices you will need the HomeKit™ setup code, located on the pull out tab.One Color IconBasicConnected App IconOptimized Small Versions.75pt Additional .5pt AdditionalXXX-XX-XXXHomeKit™ setup code is located on the pull out tab of the iDevices® Wall Outlet. Pull out tabXXX-XX-XXX

16 17REFERENCE INFORMATION LED COLOR CODES LED State Description Blue FlashingWall Outlet is waiting for the handset to congure the accessory’s Wi-Fi®. The LED ashs blue. Solid BlueWall Outlet is waiting for the handset to initiate and complete pair set up through either Wi-Fi® or BLE (Bluetooth Low Energy). The LED is solid blue. Slow Blue FlashPairing mode has expired and Wall Outlet is waiting for the user to press either On/Off button for about 3 seconds to reenter pairing mode. The LED slowly ashes blue. Solid BlueTo reinitiate the pairing mode, hold either On/Off button down for 3 seconds and the LED will turn solid blue.LED State DescriptionGreen FlashWhen Wall Switch joins a Wi-Fi® network, (i.e., the link is up) the LED ashes green for 1 second. Orange FlashWhen Wall Outlet has lost the connection to the Wi-Fi® network, (i.e., the link is down) the LED slow ashes orange until the link is up. Red FlashTo initiate a device reset, which will clear all Wi-Fi® and pairing information, hold either On/Off button down for 10 seconds until the LED rapidly ashes red. When the button is released the unit will reboot and reenter the pairing mode.Purple Flash When Wall Outlet receives a request to identify itself, it rapidly ashes purple.

18 19SUPPORT If at any time you require assistance, please contact our Customer Experience Team. Call: 888.313.7019 Email: Support@iDevicesinc.com Visit: iDevicesinc.com/SupportTROUBLESHOOTING AND SUPPORT A DEVICE RESET CAN RESOLVE MOST ISSUES. Reset your Wall Outlet by holding either On/Off button down until the LED ashes red rapidly.

20 21REGULATORY INFORMATION Product Information:Manufacturer: iDevices LLCModel: IDEV0010FCC: 2ABDJ-OUTLETIC: 11569A-OUTLETThe iDevices® Wall Outlet IDEV0010 is certied to comply with applicable FCC and IC rules and regulations governing RF and EMI emissions. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. FCC Notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

22 23• Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected • Consult the dealer or an experienced radio/TV technician to help. • Changes or modications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment IC Notice This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement. This device complies with the Industry Canada license exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.ReferencesRequires the iDevices® Connected app. For warranty information please visit iDevicesinc.com/Warranty.

Navigation menu