iDevices OUTLET In-wall On/Off Smart Outlet User Manual 15 IDEV0010 UserMan

Download:
Mirror Download [FCC.gov]
Document ID	3182076
Application ID	2UcSaR+G/+proKUcEUs7oA==
Document Description	15_IDEV0010 UserMan
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	80.88kB (1011045 bits)
Date Submitted	2016-11-01 00:00:00
Date Available	2016-11-01 00:00:00
Creation Date	2016-10-25 10:26:45
Producing Software	Adobe PDF Library 15.0
Document Lastmod	2016-10-26 21:03:25
Document Title	15_IDEV0010 UserMan
Document Creator	Adobe InDesign CC 2015 (Macintosh)

I N S TA L L AT I O N & S E T U P G U I D E
I N WA L L S O L U T I O N S
REQUIRES
• Wi-Fi 2.4 GHz 802.11 b/g/n compatible network
		 • Router Security Settings Supported: WPA, WPA2, or None
• Free iDevices® Connected App
• 120VAC “Line” and “Neutral” wires in each gang box
• HomeKit requires an iPhone, iPad or iPod touch with iOS9 or later
• Android™ 4.3+ devices with Bluetooth® Smart technology
®
NOTE: 5 GHz networks are not compatible.
TOOLS NEEDED
R AT I N G S
• Philips Screwdriver
• Pliers
• Wire Cutter/Stripper
• Voltage Detector
• Flathead Screwdriver
Input: 125VAC, 60Hz
Output: 125VAC, 60Hz
Tungsten: 600W (5A)
General Use: 1800W (15A)
Motor: 1/2 HP
Resistive: 1800W (15A)
• Not intended for critical medical or life support equipment.
• Use caution when using the iDevices® Wall Outlet to control any appliances which produce heat or
mechanical motion, or could create a hazardous condition when operated while unattended.
• The iDevices® Wall Outlet is not user-serviceable. Do not attempt to open the enclosure for any reason.
• The iDevices® Wall Outlet is only for installation with copper or copper-clad wires. Do not install in a
circuit that uses aluminum wires.
• The iDevices® Wall Outlet must be installed in a manner that conforms to all applicable national,
state, and local building codes.
• The iDevices® Wall Outlet is intended for dry, indoor use only.
• The iDevices® Wall Outlet is not a Ground Fault Circuit Interrupt (GFCI) or Arc Fault Circuit Interrupt
(AFCI) protected outlet.
• The iDevices® Outlet should be installed in a circuit with a breaker/fuse rated at no more
than 15 Amps. The total load (both receptacles combined) should not exceed 1800W.
! RISK OF ELECTRIC SHOCK, SEVERE BURNS, AND FIRE: Your safety is important to us.
Electricity is dangerous and can cause personal injury and property damage if handled improperly.
A working knowledge of electrical installation is required to install this product. If you are not
comfortable working with electricity do not attempt to install the iDevices® Wall Outlet and seek
professional assistance from a qualified electrician.
B E F O R E Y O U S TA RT
• Read through this Installation Guide in its entirety before starting
installation of your iDevices® Wall Outlet or removal of your old
outlet. Incorrect installation can be dangerous and can damage
your iDevices® Wall Outlet or your home.
• Visit our YouTube channel for tips on installation and setup:
www.youtube.com/user/iDevicesInc
• Turn OFF the power to the circuit you are working on at your 		
home’s breaker or fuse panel.
• Where ever possible, install the iDevices® Wall Outlet in a nonmetallic gang box and use a non-metallic faceplate, as metal gang
boxes and faceplates can decrease the Wi-Fi® signal strength.
• Check that your mobile device is compatible with the iDevices®
Wall Outlet at iDevicesinc.com/Compatibility
• It is YOUR responsibility to be sure that products are installed in
accordance with applicable building codes. Check with your local
building office if you have questions.
• Download the Free iDevices® Connected app.
GETTING TO KNOW THE
i D E V I C E S ® WA L L O U T L E T
Top Outlet On/Off. Pressing this button will turn the individual outlet On
or Off. DEVICE RESET: Press and hold for 10 seconds until LED blinks red.
PAIRING MODE: Press and hold for 3 seconds until LED is solid blue.
Bottom Outlet On/Off. Pressing this button will turn the individual outlet
On or Off. DEVICE RESET: Press and hold for 10 seconds until LED blinks
red. PAIRING MODE: Press and hold for 3 seconds until LED is solid blue.
Status LED/Night Light. Provides setup status and used as a night light
during operation. Refer to LED color codes on page 16.
Pull Out Tab. Refer to this
when prompted to enter your
HomeKit™ code during the setup
on a iOS device.
Device Reboot. Pressing this
cycles power to the entire unit.
I N S TA L L AT I O N
STEP 1
Take a photo of your existing wiring for future reference. Turn off the
power to the circuit at your breaker or fuse panel. If you are replacing
an existing outlet, verify that the outlet no longer has power before
proceeding.*
STEP 2
Wire the receptacle in place of an existing receptacle according to
the adjacent diagram with the provided wire nuts. Ensure the wire
nuts are fastened securely.
*If the outlet is in a multiple-gang box (with two or more switches and/or outlets), make sure that all
circuits in the gang box are turned off at the breaker or fuse panel.
WHITE
BLACK
COPPER
NEUTRAL
LINE
GROUND
STEP 3
Secure the iDevices Wall Outlet back into the gang box.
STEP 4
Turn the power back on at the breaker. If the outlet is connected
properly, you should see the LED indicator rapidly flash blue to
indicate the unit is ready to connect to the app.
10
LED will rapidly flash blue when
it’s ready to connect to the app.
11
CONNECTING TO YOUR NETWORK
IDEVICES® CONNECTED APP
Download the iDevices® Connected app and connect to your
home’s Wi-fi® network. To proceed with setup please be sure
both Wi-fi® and Bluetooth® are enabled on your device.
Icon
12
POWER ON OUTLET
Ensure the Power/Breaker is
turned back On and the LED
on the iDevices® Wall Outlet
is rapidly flashing blue. Note:
If the LED is not flashing blue
rapidly, hold either of the On/
Off buttons until the LED blinks
red, then release to perform
a Device Reset and re-enter
pairing mode. At this point, the
LED will rapidly flash blue.
LED will
rapidly
flash blue
when it’s
ready to be
paired.
13
CONNECT OUTLET
HomeKit™ setup code is located on the
pull out tab of the iDevices® Wall Outlet.
Launch the iDevices® Connected app and you will be guided through
the process of connecting your Wall Outlet. For iOS devices you will
need the HomeKit™ setup code, located on the pull out tab.
XXX-XX-XXX
XXX-XX-XXX
Connected App Icon
Basic
One Color
Icon
Pull out tab
Optimized Small Versions
14
.75pt Additional
.5pt Additional
15
R E F E R E N C E I N F O R M AT I O N
LED COLOR CODES
LED State Description
Blue Flashing
Solid Blue
Slow Blue Flash
Solid Blue
16
Wall Outlet is waiting for the handset to configure the accessory’s
Wi-Fi®. The LED flashs blue.
Wall Outlet is waiting for the handset to initiate and complete pair set up
through either Wi-Fi® or BLE (Bluetooth Low Energy). The LED is solid blue.
Pairing mode has expired and Wall Outlet is waiting for the user to press either
On/Off button for about 3 seconds to reenter pairing mode. The LED slowly
flashes blue.
To reinitiate the pairing mode, hold either On/Off button down for 3 seconds
and the LED will turn solid blue.
LED State Description
Green Flash
Orange Flash
Red Flash
Purple Flash
When Wall Switch joins a Wi-Fi® network, (i.e., the link is up) the LED flashes
green for 1 second.
When Wall Outlet has lost the connection to the Wi-Fi® network, (i.e., the link is
down) the LED slow flashes orange until the link is up.
To initiate a device reset, which will clear all Wi-Fi® and pairing information,
hold either On/Off button down for 10 seconds until the LED rapidly flashes
red. When the button is released the unit will reboot and reenter the pairing
mode.
When Wall Outlet receives a request to identify itself, it rapidly flashes purple.
17
S U P P O RT
If at any time you require assistance, please contact our
Customer Experience Team.
T R O U B L E S H O O T I N G A N D S U P P O RT
A DEVICE RESET CAN RESOLVE MOST ISSUES. Reset your Wall
Outlet by holding either On/Off button down until the LED flashes
red rapidly.
Call: 888.313.7019
Email: Support@iDevicesinc.com
Visit: iDevicesinc.com/Support
18
19
R E G U L AT O RY I N F O R M AT I O N
Product Information:
Manufacturer: iDevices LLC
Model: IDEV0010
FCC: 2ABDJ-OUTLET
IC: 11569A-OUTLET
The iDevices® Wall Outlet IDEV0010 is certified to comply with applicable
FCC and IC rules and regulations governing RF and EMI emissions.
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) This device may not cause harmful
interference, and (2) This device must accept any interference received,
including interference that may cause undesired operation.
20
FCC Notice
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation.
This equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
21
22
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected
• Consult the dealer or an experienced radio/TV technician to help.
• Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment
compromettre le fonctionnement.
IC Notice
References
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB003 du Canada. Le présent appareil est conforme aux CNR d’Industrie
Canada applicables aux appareils radio exempts de licence. L’exploitation
est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas
produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout
brouillage radioélectrique subi, même si le brouillage est susceptible d’en
This device complies with the Industry Canada license exempt RSS
standard(s). Operation is subject to the following two conditions: (1) this
device may not cause interference, and (2) this device must accept any
interference, including interference that may cause undesired operation of
the device.
Requires the iDevices® Connected app.
For warranty information please visit iDevicesinc.com/Warranty.
23
Apple, the Apple logo, iPhone, and iPod touch are trademarks of Apple
Inc., registered in the U.S. and other countries. App Store is a service mark
of Apple Inc. HomeKit is a trademark of Apple Inc. Controlling HomeKitenabled accessories away from home requires an Apple TV (3rd generation
or later) with Apple TV software 7.0 or later and an iPhone, iPad, or iPod
touch with iOS 9 or later.
Amazon, Echo, Alexa and all related logos are trademarks of Amazon.com,
Inc. or its affiliates. Android is a trademark of Google Inc. Google Play and
the Google Play logo are trademarks of Google Inc.
24

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : Yes
Tagged PDF                      : Yes
XMP Toolkit                     : Adobe XMP Core 5.6-c015 84.158975, 2016/02/13-02:40:29
Create Date                     : 2016:10:25 10:26:45-04:00
Metadata Date                   : 2016:10:26 21:03:25-04:00
Modify Date                     : 2016:10:26 21:03:25-04:00
Creator Tool                    : Adobe InDesign CC 2015 (Macintosh)
Instance ID                     : uuid:15977095-4af7-e24a-8663-174d95a179a9
Original Document ID            : xmp.did:0c7f290b-b31f-46e2-a01d-3e5df28428f5
Document ID                     : xmp.id:7e4ef8b9-1272-43c4-a176-9dfb194a5d07
Rendition Class                 : proof:pdf
Derived From Instance ID        : xmp.iid:32eb7447-4655-41b9-9075-1f815f2ebca1
Derived From Document ID        : xmp.did:52e7014e-85c0-4e68-96a1-a62ed54f4b7b
Derived From Original Document ID: xmp.did:0c7f290b-b31f-46e2-a01d-3e5df28428f5
Derived From Rendition Class    : default
History Action                  : converted
History Parameters              : from application/x-indesign to application/pdf
History Software Agent          : Adobe InDesign CC 2015 (Macintosh)
History Changed                 : /
History When                    : 2016:10:25 10:26:45-04:00
Format                          : application/pdf
Producer                        : Adobe PDF Library 15.0
Trapped                         : False
Page Count                      : 13
Creator                         : Adobe InDesign CC 2015 (Macintosh)

EXIF Metadata provided by EXIF.tools