iMetrik DACP08 GSM Communication Device User Manual Installation Instructions

Download:
Mirror Download [FCC.gov]
Document ID	798959
Application ID	9uhMtRCy1H7Cd5ik3uzzqw==
Document Description	Installation Instructions
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	9.32kB (116554 bits)
Date Submitted	2007-06-01 00:00:00
Date Available	2007-06-01 00:00:00
Creation Date	2007-06-01 08:05:48
Producing Software	GPL Ghostscript 8.15
Document Lastmod	2007-06-01 08:06:10
Document Title	Microsoft Word - Installation instructions iMetrik BW 2007-05-30 _1 per page_.doc
Document Creator	PScript5.dll Version 5.2.2
Document Author:	alain.byette

This device complies with Part 15 of the FCC Rules and with RSS-210 of Industry Canada.
Operation is subject to the following two conditions. (1) This device may not cause harmful
interference, and (2) this device must accept any interference received, including interference that
may cause undesired operation.
IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance of 20cm between the radiator
and your body. This transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
Warning: Changes or modifications made to this equipment not expressly approved by iMetrik Inc may
void the FCC authorization to operate this equipment.
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
-- Consult the dealer or an experienced radio/TV technician for help.
Note:
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
iMetrik Solutions Inc.
Support: 1(866) 276-5382
May 29th, 2007 - Form: Install-01 Ver 1.3
Installation instruction iMetrik DACP08
You are currently installing iMetrik DACP08 module. If you are unsure of any step of this process, please call our Customer
Care service at 1-899-276-5382. This package includes the following components: ONE DACP08 module, One GSM cellular
antenna, ONE GPS antenna, ONE power cable assembly; TWO starter-interrupt cables. (DACP08 only)
Installation notes
•
To be install only inside vehicle cabin
•
GPS antenna must be mounted so that no metal is impeding sky-view, rounded side up
•
GSM antenna must be located on a non metallic area.
•
See all the warnings and notes on last page before installation
•
No power should be applied to unit if antennas are not connected.
INSTALLATION PROCEDURE
1) Disconnect the battery from the vehicle electrical system
Note: all components of the device (GPS/RF
from this point forward, to avoid possible damage due to
antennas) should be installed behind the dashboard
shorting of exposed wire.
7)
Install the RF antenna on a flat, non-metallic surface.
For best results, install in a vertical position six inches
The unit must never be powered up without antennas
connection.
away from any metal.
2) Locate power for constant 12V power and a good
8)
Screw the RF antenna into the device RF connector
ground (ignition off)
9)
Install the GPS antenna in the vehicle. Choose a
3) If holder is separate; connect the red wire from the
location where it has NO METAL impeding its view of
power cable assembly to one end of the fuse holder, and
the sky. Connect the GPS antenna to the device.
the other end of the fuse holder to the constant 12V
10) Connect the 4-pin power cable to the device. Install the
iMETRIK 200G device in the vehicle.
power source.
4) Ground the black wire of the power cable assembly to
When connecting or disconnecting either antenna
the vehicle’s frame. (ignore purple wires if present)
from the device, make sure to remove the 12V
If installing a LR 200G, jump to step 7
power cable first. Severe damage to the unit may
5) Find the vehicle’s starter wire and cut it. The starter wire
result otherwise
only has 12V when cranking.
11) Reconnect the vehicle’s battery.
6) Connect the wires from the starter-interrupt cables to
12) Park the vehicle outside, away from trees or tall
each end of the starter wire. Connect the “Quickbuildings. Verify the installation was a success by
Release” connectors from the starter-interrupt cables to
performing a “Location” command from your account.
the device.
Make sure all connections are soldered and well
insulated
WELL INSULATED
TESTING
LED
COLOR ►
1:POWER
GREEN
2:STARTER
RED
OFF
NO POWER
ENABLED
FAST BLINK
SLOW
BLINK
ON :
N/A
N/A
POWER
**
***
N/A
3:GPS
RED
NO POWER/
GPS ERROR
ACQUIRING***
4: CELLULAR
RED
NO POWER/
ERROR*
NETWORK ERROR
WARNING MODE
HAS DATE/TIME
ACQUIRING**
DISABLE MODE
GOOD GPS FIX
CONNECTED
CELLULAR LED is OFF during the approximately 10 seconds after power-on. This is normal.
Acquiring time of approximately 75 seconds during power-on. Users should wait at least 2 minutes before addressing the
device the first time.
GPS LED is OFF during the approximately 10 seconds after power-on. This is normal. GPS LED will stay off if there is a
cellular error on power-up.
- It is recommended to insulate the in-line fuse with shrink wrap or electrical tape
- Ensure fuse is properly inserted
S/N:
IMEI:
YEAR:
MAKE:
MODEL:
VIN:
iMetrik Solutions Inc.
Support: 1(866) 276-5382
May 29th, 2007 - Form: Install-01 Ver 1.3

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Page Count                      : 1
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : uuid:36bb118c-c1a3-4949-b7d2-9524ebc6a324
Modify Date                     : 2007:06:01 08:06:10+02:00
Create Date                     : 2007:06:01 08:05:48+02:00
Metadata Date                   : 2007:06:01 08:06:10+02:00
Document ID                     : uuid:736436ca-5d18-4d33-a6f1-c85a145b2dfd
Format                          : application/pdf
Title                           : Microsoft Word - Installation instructions iMetrik BW 2007-05-30 _1 per page_.doc
Creator                         : PScript5.dll Version 5.2.2
Author                          : alain.byette
Producer                        : GPL Ghostscript 8.15

EXIF Metadata provided by EXIF.tools