Installation Guide for Energizer models including: Force 3S, Force 3.6S, Force 4.6S, Force 5S, Force 6S, Force 3S Force-Series-SP Single Phase Inverter, Force 3S, Force-Series-SP Single Phase Inverter, Single Phase Inverter, Phase Inverter, Inverter
Jun 14, 2023 — sure the two moun ng grooves on the back are properly fixed with the two bracket bars. Model. Force 3S Force 3.6S Force 4.6S Force 5S Force 6S.
Quick Installaon Guide 1. Packing List Energizer Force 3.0S-6.0S Single Phase Inverter 2. Inverter Installaon Please make sure the inverter will be installed with a proper distance as shown below. A B C D E F G Quick Installaon Guide J K H I L M N Object Quanty Descripon Object Quanty Descripon A 1 Inverter I 1 Communicaon connector B 1 Bracket J 1 Quick installaon guide C 4 DC connector (F/M) K 1 CT (Oponal) D 1 AC connector L 1 WiFi/LAN/GPRS(Oponal) E 3 Expansion tube M 1 Meter (Oponal) F 3 Expansion screw N 2 Unlock tool DC pin contact G 4 (2*posive, 2*negave) H 1 Earth terminal 30cm 30cm 30cm 30cm Posion Le Right Top Boom Front Min Size 30cm 30cm 30cm 30cm 30cm Step 1: Fix the bracket on the wall Choose the place you want to install the inverter. Place the bracket on the wall and mark the posion of the 3 holes from bracket. Drill holes with electric drill, make sure the holes are at least 50mm deep, and then ghten the expansion tubes. Insert the expansion tubes into the holes and ghten them. Install the bracket with the expansion screws. Step 2: Match the inverter with wall bracket Hang the inverter over the bracket, slightly lower the inverter, and make sure the two mounng grooves on the back are properly fixed with the two bracket bars. 3. Wiring Steps AC Wiring - Cable dimensions Model Force 3S Force 3.6S Force 4.6S Force 5S Force 6S Cable 4mm² 4mm² 6mm² 6mm² 6mm² Micro-Breaker 25A 25A 40A 40A 40A · Push the threaded sleeve to connecon terminal unl both are locked ghtly on the inverter. · Remove the AC connector, press the bayonet out of the slot with a small screwdriver or the unlock tool and pull it out, or unscrew the threaded sleeve, then pull it out. DC Wiring · Turn off the DC switch. · Choose 12 AWG wire to connect the PV module. · Trim 6mm of insulaon from the wire end. · Separate the DC connector as below. Plug Pin contact cable nut D- D+ · Insert striped cable into pin contact and ensure all conductor strands are captured in the pin contact. · Crimp pin contact by using a crimping plier. Put the pin contact with striped cable into the corresponding crimping pliers and crimp the contact. Grounding Wiring Screw the ground screw with screwdriver as shown below. · Insert pin contact through the cable nut to assemble into back of the male or female plug. When you feel or hear a "click" the pin contact assembly is seated correctly. · Unlock the DC connector - Use the specified wrench tool. - When separang the DC + connector, push the tool down from the top. - When separang the DC - connector, push the tool down from the boom. - Separate the connectors by hand. 4. Startup Procedure 1. Aer checking all connecons are correct, turn on the external DC /AC breakers. 2. Turn the DC switch to"ON" posion. 3. Inverter will start automacally when PV panels generate enough energy, the LED will be green. 4. Complete inverter Start-up guide Aer the inial start-up the inverter, display will go to the language sengs page, short press to switch language and long press to confirm selecon. Once language set, display will guide to set the safety regulaon. Short press to switch safety regulaon, and long press to confirm selecon. - Trim all the wires to 52.5mm and the PE wire to 55mm. - Use the crimping pliers to trim 12mm of insulaon from all wire ends as shown in the picture. L: Brown/Red Wire N: Blue/Black Wire PE: Yellow & Green Wire 12 Note: Please refer to local cable type and color for actual installaon. · Separate the AC plug into three parts as below. a. Hold the middle part of the female insert, rotate the back shell to loosen it, and detach it from female inset. b. Remove the cable nut (with rubber insert) from the back shell. · Slide the cable nut, then the back shell onto the cable. · Push the threaded sleeve into the socket, ghten up the cap on the terminal. Note: · When starng the inverter for the first me, the country code will be set by default to the local sengs. Please check if the country code is correct. · Set the me on the inverter using the buon or by using the APP. To view all relevent documentation such as Install Manuals and Remote Monitoring guides, scan the QR code below. 5. Contact Details: 8 Star Energy Pty Ltd. | Level 35, 477 Collins Street, Melbourne, VIC 3000, Australia 8 Star Energy ESS Ltd. | The Black Church, St Mary's Place, Dublin, DO7 P4AX, Ireland 8 Star Energy North America Inc. | 888 Prospect Street, La Jolla, California, 92037, USA © 2023 Energizer. Energizer and certain graphic designs are trademarks of Energizer Brands, LLC and related subsidiaries and are used under license by 8 Star Energy Pty Ltd. All other brand names are trademarks of their respecve owners. Neither 8 Star Energy Pty Ltd nor Energizer Brands, LLC is affiliated with the respecve owners of their trademarks. V2.0 10-203-000003-04Adobe Illustrator 25.3 (Windows) Adobe PDF library 15.00