INSTALLATION MANUAL
Enter the password to open this PDF file:
Preparing document for printing…
ES-SUB-IW-All Models Manual 1903118 1750 INSTALLATION MANUAL
ESS-SUB-SNGL-8 ESS-SUB-ENC-RET-SGL8 ESS-SUB-ENC-IWIC-PCO ESS-SUB-ENC-IW-PCON
page | 2
snapav.com Support 866.838.5052
page | 3
INTRODUCTION
Thank you for purchasing Episode® Signature speakers. Episode is one of the most highly-regarded brands of speakers available today. We appreciate your business and we stand committed to providing our customers with the highest degree of quality and service in the industry.
For optimal system performance, we recommend pairing them with our acclaimed Episode Signature speakers and Episode Subwoofer Amplifiers..
To complete installation, follow these guidelines.
SETUP
Subwoofer Placement
The placement and configuration of the subwoofer can affect its performance. All rooms are different and the strongest output will likely occur if you place your subwoofer in the front of the room or on the same wall or ceiling as your front channel / distributed speakers. Keep subwoofers about 2 feet away from corners and other surfaces that might interfere with or reflect sound, such as tall furniture.
CUTOUT DIMENSIONS
Refer to the chart below to verify the correct dimensions prior to cutting drywall.
Model ESS-SUB-SNGL-8
Cutout Dimension Mounting Depth
9.7"
3 7/8"
ESS-SUB-ENC-RET-SGL8
12" × 12"
3 7/8"
ESS-SUB-ENC-IW-PCON
9.7"
3 1/2
ESS-SUB-ENC-IWIC-PCO
9.7"
51/8"
Existing Construction Install
Free-air Subwoofer installations can be simplified by using Episode pre-construction brackets (sold separately). Install them prior to drywall to allow for precise placement of the subwoofer. Secure the wiring within reach of the bracket for easy access. If using the speaker as a free air installation, make a cutout for the speaker using the supplied template.
© 2019 Episode®
page | 4
Allow space for the bezel if installing near adjacent objects, or cut the hole in two steps as shown below.
OBSTRUCTION PLUG
1. Cut the drywall at a 45° angle so that if the speaker is too close to an obstruction, you can easily `plug' the hole.
2. If there are no obstructions, cut the drywall again, this time at a 90° angle.
g "no personal connection" to the original text, decided to use the lm as a ground-up reimagining of the story - a hero's journey with magical swords and ancient prophecies and a strong moral message about... following orders?
3. Insert the subwoofer into the cutout. Thin bezel round grille included with free-air subwoofer.
Using The Retrofit Backbox
Using an enclosure in combination with the free air subwoofer can improve overall system performance by controlling the air volume behind the wall. In addition to added performance, enclosures also aid in reducing transient noise to adjacent rooms. If using the retrofit enclosure (ESS-SUB-ENC-RET-SGL8) first make a cutout for the enclosure using the supplied template. Allow space for the bezel if installing near adjacent objects, or cut the hole in two steps as shown below.
Note: Wire the retrofit enclosure before placing and securing in the wall.
OBSTRUCTION PLUG
1. Cut the drywall at a 45° angle so that if the enclosure is too close to an obstruction, you can easily `plug' the hole.
2. If there are no obstructions, cut again at a 90° angle.
3. Wire the retrofit enclosure, then insert it into the space cut into the drywall.
snapav.com Support 866.838.5052
page | 5
DOG EARS VERTICAL
4. Secure the back box into the drywall by tightening the dog ears or using the frame of the enclosure to fasten to joists.
NOTE: Stud bays can be spanned vertically or horizontally with 2 subwoofer units without needing to cut the stud joist. Ensure the retrofit enclosure bezels butt up to one another and are in alignment so the dual sub grille will fit over the subs. See the specifications tables for optional grille accessories. Stud
Joint Fastener Locations
HORIZONTAL
Adding the Subwoofer to the Retrofit Enclosure
Wire the subwoofer to the pigtail contained within the enclosure before installing into the wall. Insert ESS-SUB-SNGL-8 after completing install of the retrofit enclosure(s).
IMPORTANT: Be sure to align the dog ears of the subwoofer to the markings shown on the enclosure. If not done properly, the dog ears may jam against the side, making the speaker very difficult to remove.
NEW CONSTRUCTION INSTALLATIONS
ESS-SUB-ENC-IW-PCON and ESS-SUB-ENC-IWIC-PCO enclosures are intended for install during the pre-construction phase in the home. These controll the air volume behind the wall, limit the footprint visible from the finished surface while also helping to reduce transient noise to adjacent rooms.
IMPORTANT: Consider placement of subwoofers early in the process and test the placement of the product in the room prior to installing drywall. Wire enclosures BEFORE drywall is installed.
Note: Take extra precautions to secure and dampen studs, drywall, pipes, wires, etc in the wall during the process of installing the pre-construction enclosure.
© 2019 Episode®
page | 6
ESS-SUB-ENC-IWIC-PCO (In Ceiling Back Box) Without extention Arms The ESS-SUB-ENC-IWIC-PCO is designed for in-ceiling and in-wall preconstruction applications. This enclosure only fits into a 2"× 6" stud bays and can be used in walls as well. The ESS-SUB-ENC-IW-PCON should be used if the wall is built with 2" × 4" studs. 1. Choose the location for the enclosure and install the brackets.
× 6
2. Secure the enclosure to the studs through the brackets.
× 6
With Extension Arms NOTE: The extension arms allow for installation in a stud bay spanning up to 24". Slotted holes allow for side-to-side adjustment within a stud bay prior to securing in the final position. 1. Choose a stud bay for installation of the back box using the extension
arms. 2. Attach the extension arms to the existing brackets on the enclosure,
using the supplied hardware.
× 6
× 6
snapav.com Support 866.838.5052
3. Secure the extention arms to the studs.
page | 7
ESS-SUB-ENC-IW-PCON
The ESS-SUB-ENC-IW-PCON is designed to expand air volume behind the wall for an improved sound performance. Follow the instructions below to install this enclosure before the drywall is installed. This enclosure is designed for use with 2" × 4" studs.
1. Choose a stud bay for installation of
× 6
the back box.
2. Leave approximately 4" of room at the bottom of the enclosure for easier wiring.
3. Secure the enclosure to the stud using the included brackets, again, taking extra precaution to ensure enclosure is tight to studs and drywall to avoid vibrations during use.
Note: By default the ESS-SUB-IW-PCON enclosure is configured for a single subwoofer in the lower location. To move the subwoofer to the upper location, swap the blank plate with the drywall flange. To convert the enclosure for use with dual subwoofers, replace the blank with the included second drywall flange.
© 2019 Episode®
BLANK
FLANGE
page | 8
Adding the Subwoofer to the Enclosure for ESS-SUB-ENC-IWIC-PCO and ESS-SUB-ENC-IW-PCON
Complete the instructions below once the drywall has been installed, using the drywall flange to cut out the opening in the sheetrock. 1. Prewire the subwoofer to the pigtails in the enclosure. 2. Insert the subwoofer into the enclosure. 3. Tighten the dogs to secure.
SECURING THE ESS-SUB-SNGLE-8 SUBWOOFER
Engage and Tighten
Spring Dog
1. Insert the subwoofer into the opening and turn the screw for each of the dogs one quarter turn clockwise to engage the spring mechanism.
PARKED Carrier
Spring Dog ENGAGED
Carrier Spring
Dog TIGHTENED
2. The subwoofer is now held in place, freeing up your hands so that you may continue to tighten the dogs safely.
3. Tighten to send the carrier to retrieve the dog until you feel resistance, but do not over tighten. If using a drill, use a low-torque setting.
snapav.com Support 866.838.5052
page | 9
Disengage and Remove
Carrier
Spring Dog TIGHTENED
! IMPORTANT: The dogs must be engaged AND tightened before attempting to remove the subwoofer. The dogs will not retract into the parked position if not fully engaged and tightened.
1. Turn each dog screw in a counterclockwise direction until the dog is in its original parked position.
Spring Dog
PARKED
2. Once the dogs are disengaged, the subwoofer is easily removed from the ceiling or wall.
© 2019 Episode®
page | 10
CONNECT
It is recommended to pair Episode Signature subwoofers and enclosures with Episode subwoofer amplifiers. The configuration, number of subwoofers, and size of the room presents several amplifier options from which to choose.
Small to Medium Room Connection Diagram The EA-AMP-SUB-1D-150 amplifier is recommended for spaces less than 1500 square ft up to 2500 square feet. 1. Connect receiver directly to the amplifier. 2. Connect speaker(s) to amplifier observing proper polarity (+ to + and to ).
ESS-SUB-SNGL-8 The amplifier EQ toggle should be set to A.
R CEN RS
L
SUB
LS
+ 12V Trigger Out
Switched Outlet
AVR/SOURCE
L (LFE)
R
IN
OUT
OUT DC 12V TRIGGER
A BC
ON BYPASS TRIGGER ON
CROSSOVER
PHASE
EQ
EQ
AUTO
IN
SETTINGS
MODE
POWER MODES 50 300 (LFE)
0 180
VOLUME
0
10
EA-AMP-SUB-1D-150
EA-AMP-SUB-1D-150
Designed and Engineered in USA Made in China
FUSE T3.15AL/250V 100-120V~60Hz/220-240V~50Hz 150WATTS
SUB 1
Total Impedance (Sub 1 + Sub 2) Minimum 4
SUB 2
100-120V AC
220-240V AC
+
ESS-SUB-SNGL-8
L (LFE)
R
IN
OUT
OUT DC 12V TRIGGER
A BC
ON BYPASS TRIGGER ON
CROSSOVER
PHASE
EQ
EQ
AUTO
IN
SETTINGS
MODE
POWER MODES 50 300 (LFE)
0 180
VOLUME
0
10
EA-AMP-SUB-1D-150
SUB 1
Total Impedance (Sub 1 + Sub 2) Minimum 4
SUB 2
Designed and Engineered in USA Made in China
FUSE T3.15AL/250V 100-120V~60Hz/220-240V~50Hz 150WATTS
100-120V AC
220-240V AC
snapav.com Support 866.838.5052
+
page | 11
R CEN RS
L
SUB
LS
+ 12V Trigger Out
Switched Outlet
L (LFE)
R
IN
OUT
AVR/SOURCE
EA-AMP-SUB-1D-150
OUT DC 12V TRIGGER
A BC
ON BYPASS TRIGGER ON
CROSSOVER
PHASE
EQ
EQ
AUTO
IN
SETTINGS
MODE
POWER MODES 50 300 (LFE)
0 180
VOLUME
0
10
EA-AMP-SUB-1D-150
SUB 1
Total Impedance (Sub 1 + Sub 2) Minimum 4
SUB 2
Designed and Engineered in USA Made in China
FUSE T3.15AL/250V 100-120V~60Hz/220-240V~50Hz 150WATTS
100-120V AC
220-240V AC
-
-
+
+
ESS-SUB-SNGL-8
ESS-SUB-ENC-IWIC-PCO / ESS-SUB-ENC-RET-SGL8 The amplifier EQ toggle should be set to C.
R CEN RS
L
SUB
LS
+ 12V Trigger Out
Switched Outlet
AVR/SOURCE
L (LFE)
R
IN
OUT
OUT
DC 12V TRIGGER
A BC
ON BYPASS TRIGGER ON
CROSSOVER
PHASE
EQ
EQ
AUTO
IN
SETTINGS
MODE
POWER MODES 50 300 (LFE)
0
180
VOLUME
0
10
EA-AMP-SUB-1D-150
EA-AMP-SUB-1D-150
Designed and Engineered in USA Made in China
FUSE T3.15AL/250V 100-120V~60Hz/220-240V~50Hz 150WATTS
SUB 1
Total Impedance (Sub 1 + Sub 2) Minimum 4
SUB 2
100-120V AC
220-240V AC
-
+
OR
ESS-SUB-ENC-IWIC-PCO or ESS-SUB-ENC-RET-SGL8 + ESS-SUB-SNGL-8
L (LFE)
R IN
OUT
OUT
DC 12V TRIGGER
IN
IR
UPDATE
© 2019 Episode®
OPERATE
EA-AMP-SUB-1D-500R
SUB 1
Total Impedance (Sub 1 + Sub 2) Minimum 4
SUB 2
Designed and Engineered in USA Made in China
FUSE T8AL/250V 100-120V~60Hz/220-240V~50Hz 500WATTS
100-120V AC
220-240V AC
page | 12
ESS-SUB-ENC-IW-PCON The amplifier EQ toggle should be set to B.
R CEN RS
L
SUB
LS
+ 12V Trigger Out
Switched Outlet
AVR/SOURCE
L (LFE)
R
IN
OUT
OUT DC 12V TRIGGER
A BC
ON BYPASS TRIGGER ON
CROSSOVER
PHASE
EQ
EQ
AUTO
IN
SETTINGS
MODE
POWER MODES 50 300 (LFE)
0 180
VOLUME
0
10
EA-AMP-SUB-1D-150
EA-AMP-SUB-1D-150
Designed and Engineered in USA Made in China
FUSE T3.15AL/250V 100-120V~60Hz/220-240V~50Hz 150WATTS
SUB 1
Total Impedance (Sub 1 + Sub 2) Minimum 4
SUB 2
100-120V AC
220-240V AC
ESS-SUB-ENC-IW-PCON + ESS-SUB-SNGL-8 (qty. 1)
-+
Medium to Large Room Connection Diagram L (LFE)
OUT
DC 12V TRIGGER
EA-AMP-SUB-1D-500R
Designed and Engineered in USA Made in China
FUSE T8AL/250V
100-120V~60Hz/220-240V~50Hz 500WATTS
R
OPERATE
The EA-AMP-SUB-1D-500 amplifier is recommended IN
OUT
IN
IR
UPDATE
SUB 1
Total Impedance (Sub 1 + Sub 2) Minimum 4
SUB 2
100-120V AC
220-240V AC
for
spaces
1500
square ft to over 2500 square feet.
1. Connect receiver directly to the amplifier.
2. Connect speaker(s) to amplifier observing proper polarity (+ to + and to ).
+
+
snapav.com Support 866.838.5052
page | 13
ESS-SUB-ENC-RET-SNGL8 Using the front panel of the subwoofer amplifier, select the "Dual8" preset EQ.
L (LFE)
R
IN
OUT
OUT
DC 12V TRIGGER
IN
IR
UPDATE
OPERATE
EA-AMP-SUB-1D-500R
Designed and Engineered in USA Made in China
FUSE T8AL/250V 100-120V~60Hz/220-240V~50Hz 500WATTS
SUB 1
Total Impedance (Sub 1 + Sub 2) Minimum 4
SUB 2
100-120V AC
220-240V AC
EA-AMP-SUB-1D-500
-
-
+
+
ESS-SUB-ENC-RET-SGL8
+
ESS-SUB-SNGL-8
L (LFE)
R IN
OUT
OUT
DC 12V TRIGGER
IN
IR
UPDATE
EA-AMP-SUB-1D-500
OPERATE
EA-AMP-SUB-1D-500R
SUB 1
Total Impedance (Sub 1 + Sub 2) Minimum 4
SUB 2
Designed and Engineered in USA Made in China
FUSE T8AL/250V 100-120V~60Hz/220-240V~50Hz 500WATTS
100-120V AC
220-240V AC
+-
+-
ESS-SUB-ENC-RET-SGL8 (qty. 4) + ESS-SUB-SNGL-8 (qty. 4)
+-
+-
© 2019 Episode®
R CEN RS
L
SUB
LS
page | 14
+ 12V Trigger Out
Switched Outlet
-
ESS-SUB-EN+ C-IWIC-PCO
Using the front panel of the subwoofer amplifier, select the "Dual8" preset L
OUT
CROSSOVER
PHASE
VOLUME
EA-AMP-SUB-1D-150
Designed and Engineered in USA
(LFE)
DC 12V
Made in China
EQ.
TRIGGER A BC
ON BYPASS TRIGGER ON
FUSE T3.15AL/250V 100-120V~60Hz/220-240V~50Hz 150WATTS
R
IN
OUT
EQ
EQ
AUTO
IN
SETTINGS
MODE
POWER MODES 50 300 (LFE)
0
180
0
10
SUB 1
Total Impedance (Sub 1 + Sub 2) Minimum 4
SUB 2
100-120V AC
220-240V AC
L (LFE)
R
IN
OUT
OUT
DC 12V TRIGGER
IN
IR
UPDATE
OPERATE
EA-AMP-SUB-1D-500R
Designed and Engineered in USA Made in China
FUSE T8AL/250V 100-120V~60Hz/220-240V~50Hz 500WATTS
SUB 1
Total Impedance (Sub 1 + Sub 2) Minimum 4
SUB 2
100-120V AC
220-240V AC
EA-AMP-SUB-1D-500
-
-
+
+
ESS-SUB-ENC-IWIC-PCO
+
ESS-SUB-SNGL-8
ESS-SUB-ENC-IW-PCON
-+
Using the front panel of the subwoofer amplifier, select the "Dual8" preset
EQ.
L (LFE)
R IN
OUT
OUT
DC 12V TRIGGER
IN
IR
UPDATE
OPERATE
EA-AMP-SUB-1D-500R
Designed and Engineered in USA Made in China
FUSE T8AL/250V 100-120V~60Hz/220-240V~50Hz 500WATTS
SUB 1
Total Impedance (Sub 1 + Sub 2) Minimum 4
SUB 2
100-120V AC
220-240V AC
EA-AMP-SUB-1D-500
ESS-SUB-ENC-IW-PCON + ESS-SUB-SNGL-8 (qty, 2)
+
+
snapav.com Support 866.838.5052
page | 15
Using the front panel of the subwoofer amplifier, select the "Dual8" preset EQ.
L (LFE)
R IN
OUT
OUT
DC 12V TRIGGER
IN
IR
UPDATE
EA-AMP-SUB-1D-500
OPERATE
EA-AMP-SUB-1D-500R
SUB 1
Total Impedance (Sub 1 + Sub 2) Minimum 4
SUB 2
Designed and Engineered in USA Made in China
FUSE T8AL/250V 100-120V~60Hz/220-240V~50Hz 500WATTS
100-120V AC
220-240V AC
ESS-SUB-ENC-IW-PCON (qty,2) + ESS-SUB-SNGL-8 (qty, 4)
-
-
+
+
-
-
+
+
FINE TUNE
To fine tune the system, leverage the rear panel of the subwoofer amplifier. EQ settings should be adjusted based on the size of the room and the size of the enclosure. Refer to the above sections for ideal EQ setting for each configuration. Crossover, phase and volume should also be adjusted to optimize performance of the system.
© 2019 Episode®
page | 16 SPECIFICATIONS
Product
ESS-SUB-SNGL-8
Connector Type
Gold-Plated Push Terminals
Frequesncy Response 30Hz - 300Hz
Nominal Impedance 8 ohms
Power Handling
150 W (RMS)/200W (Dynamic)
Sensitivity
85 dB
Speaker Grille
Steel Micro-Perf Mesh / White / low profile thin bezel
Woofer
6" Polypropylene cone woofer with vacuum-deposited titanium
Dimensions FInished 11" Diameter with Grille
Mounting Depth
3 7/8
Cutout Diameter
9.7"
Weight
6.5 lbs/ 2.96 kgs
Optional Accessories: Product Item Number:
Optional Pre-
ES-ESS-BRKT-IC-8
Construction Brackets
Optional Grille Kits
ES-ESS-GRLRND-IC-8-B
ES-ESS-GRLSQ-IC-8
ES-ESS-GRLSQ-IC-8-B
ES-ESS-GRLXRND-IC-8
Notes:
Round / thin bezel grille / Black Square (adaptor plate included) / thin bezel grille / White Square (adaptor plate included) / thin bezel grille / Black Round / Bezel-less grille / White
ES-ESS-GRLXRND-IC8-B ES-ESS-GLXSQ-IC-8
ES-ESS-GLXSQ-IC-8-B
Round / Bezel-less grille / Black
Square (adaptor plate included) / Bezel-less grille / White Square (adaptor plate included) / Bezel-less grille / Black
snapav.com Support 866.838.5052
page | 17
Optional Enclosures
ESS-SUB-ENC-RETSGL-8 ESS-SUB-ENC-IWIC-PCO
ESS-SUB-ENC-IW-PCON
Enclosure - Retrofit - minimum standard stud construction 2" x 4" - Single 8" Subwoofer installation
Enclosure - Pre-Construction - minimum standard stud construction 2" x 6" Single 8" Subwoofer installation
Enclosure - Pre-Construction - minimum standard stud construction 2" x 4" Single or Dual 8" Subwoofer installation
Product
ESS-SUB-ENC-RET-SGL-8
E S S - S U B - E N C - I W I C - ESS-SUB-ENC-IW-PCON PCO
Connector Type
Gold-Plated Push Terminals
Gold-Plated Push Terminals
Gold-Plated Push Terminals
Frequesncy Down to 22 Hz Response
Down to 20 Hz
Down to 19 Hz
Speaker Grille
Steel Micro-Perf Mesh / White / low profile thin bezel Included
Uses grille from ESS-SUB-SNGL-8 or optional ESS grilles
Optional ESS_GRLDSUB8-RET-WT and ESS-GRL-DSUB8-RET-BLK for dual retrofit subwoofer installations.
Uses grille from ESS-SUB-SNGL-8 or Optional ESS_GRL-DSUB8-RET-WT and ESS-GRL-DSUB8RET-BLK for dual retrofit subwoofer installations.
Enclosure 5/8"
Material Wall
Thickness
5/8"
5/8"
Internal Air 290 Volume (Cu. Inches)
500
1050
Dimensions FInished Diameter with Grille
14" × 14" × 4.25"
12.8" × 12.8" × 5.4" 43.4" × 12.8" × 3.3"
Mounting
3 7/8
Depth
51/8
31/2
Cutout
12" × 12"
9.7"
9.7"
Diameter
Weight
10.4 lbs/ 4.71 kgs
7.9 lbs/3.6 kgs
© 2019 Episode®
page | 18 WARRANTY
Limited Lifetime Warranty Episode® speakers have a Limited Lifetime Warranty. This warranty includes parts and labor repairs on all components found to be defective in material or workmanship under normal conditions of use. This warranty will not apply to products that have been abused, modified, or disassembled. Products to be repaired under this warranty must be returned to SnapAV or a designated service center with prior notification and an assigned Return Authorization number (RA).
CONTACTING TECHNICAL SUPPORT
866.838.5052 support@episodeaudio.com
snapav.com Support 866.838.5052
page | 19
© 2019 Episode®
© 2019 Episode® Rev: 190318-1750
Adobe InDesign CC 14.0 (Windows) Adobe PDF Library 15.0