BT12 WIRELESS AWNING CONTROL SYSTEM INSTALLATION MANUAL CAREFREE OF COLORADO 2 070029-001r9 NOTICES AND DISCLAIMERS TRADEMARKS The Bluetooth word mark and logos are registered trademarks owned by the Bluetooth SIG, Inc. Use of such marks by Carefree of Colorado is under license. Other trademarks and trade names are those of their respective owners.
................................................................................
INSTALLATION BT12 Wireless Awning Control System CONTROL SYSTEM FOR CAREFREE 12V MOTORIZED AWNINGS USING BLUETOOTH® WIRELESS TECHNOLOGY Read this manual before installing or using this product. Failure to follow the instructions and safety precautions in this manual can result in personal injury and/or cause the product to not operate properly. The BT12 Wireless Awning Control System may be installed as part of the original motorized awning installation or as an upgrade to an existing motorized awning installation. The system offers unique features not available with a standard awning installation. 1) Carefree Connects Mobile App The app provides full and enhanced control of the awning using a smart phone or tablet. The free app can be downloaded on any devices that support: 1) Current iOS or Android operating systems, and 2) Bluetooth low energy technology. 2) Full Retract When the awning is retracted, it retracts completely. It is not necessary to hold the button when closing the awning. 3) Full Extend When the awning is extended, it extends completely. It is not necessary to hold the button when opening the awning. 4) Auto-Retract The awning can be set to automatically close when windy conditions occur with the optional BT Motion Sensor. 5) Remote Control The operator can conveniently operate the awning from any location with the optional BT Remote. 070029-001r9 Printed in USA March, 2019 BT12 WIRELESS AWNING CONTROL SYSTEM INSTALLATION MANUAL NOTICES AND DISCLAIMERS CAREFREE OF COLORADO TRADEMARKS The Bluetooth® word mark and logos are registered trademarks owned by the Bluetooth SIG, Inc. Use of such marks by Carefree of Colorado is under license. Other trademarks and trade names are those of their respective owners. STATEMENTS OF COMPLIANCE BT12 Control Module BT Motion Sensor BT Remote FCC and IC identification numbers are located on the exterior surfaces of the individual components. FCC COMPLIANCE These devices comply with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) These devices may not cause harmful interference and, (2) These devices must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. IC COMPLIANCE These devices comply with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) These devices may not cause harmful interference and, (2) These devices must accept any interference received, including interference that may cause undesired operation. Ces appareils sont conformes aux normes RSS exonérées de licence d'Industrie Canada. L'opération est soumise aux deux conditions suivantes: (1) Ces appareils ne doivent pas causer d'interférences nuisibles et, (2) Ces appareils doivent accepter toute interférence reçue, y compris les interférences pouvant entraîner un fonctionnement indésirable. FCC/IC RADIATION EXPOSURE STATEMENT BT12 Control Module BT Motion Sensor This equipment complies with FCC and IC radiation exposure limits for an uncontrolled environment. The minimum distance between the radiator and people is designed to be 20cm when installed and operated. Cet équipement est conforme aux limites d'exposition aux radiations FCC et IC pour un environnement non contrôlé. La distance minimale entre le radiateur et les personnes est de 20cm lorsqu'installé et utilisé. BT12 Remote This equipment complies with FCC and IC radiation exposure limits for an uncontrolled environment. The minimum distance between the radiator and people is designed to be 5mm when operated. Cet équipement est conforme aux limites d'exposition aux radiations FCC et IC pour un environnement non contrôlé. La distance minimale entre le radiateur et les personnes est de 5mm (à l'exclusion des extrémités: mains, poignets, pieds et chevilles) lors de l'utilisation. 2 070029-001r9 CAREFREE OF COLORADO INSTALLATION MANUAL BT12 WIRELESS AWNING CONTROL SYSTEM DISCLAIMERS The BT12 Wireless Awning Control System and the Carefree Connects Mobile App are products of Carefree of Colorado, located in Broomfield, Colorado, USA. The information contained in or disclosed in this document is considered proprietary to Carefree of Colorado. Every effort has been made to ensure that the information presented in the document is accurate and complete. However, Carefree of Colorado assumes no liability for errors or for any damages that result from the use of this document. The information contained in this manual pertains to the current components and software listed on the title page. Carefree of Colorado reserves the right to cancel, change, alter or add any parts and procedures, described in this manual, without prior notice. Carefree of Colorado agrees to allow the reproduction of this document for use with Carefree of Colorado products only. Any other reproduction or translation of this document in whole or part is strictly prohibited without prior written approval from Carefree of Colorado. SERVICE AND SUPPORT www.carefreeofcolorado.com/carefreeconnects customerservice@carefreeofcolorado.com Carefree of Colorado 2145 W. 6th Ave. Broomfield, CO 80020 TABLE OF CONTENTS Where Can BT12 be Used ............................................................................................................. 5 Installation ..................................................................................................................................... 5 BT12 Control Module Installation............................................................................................................6 Awning Switch Installation ......................................................................................................................7 Awning Lights Switch Installation............................................................................................................7 Wiring Diagram .......................................................................................................................................8 Installing the BT Motion Sensor............................................................................................................10 Altitude / Longitude / Latitude .......................................................................................................10 Eclipse / Travel'r ...........................................................................................................................11 Small Box Awnings.......................................................................................................................12 Setting the System into Pairing Mode...................................................................................................13 Pairing the Motion Sensor ............................................................................................................13 Battery Replacement................................................................................................................... 16 BT Motion Sensor .................................................................................................................................16 BT Remote............................................................................................................................................16 FAQs............................................................................................................................................. 17 The Indicator Light Blinks on the BT12 Control Box. ............................................................................17 The System Beeps and the Awning Partially Retracts. ........................................................................17 The Remote Does Not Work.................................................................................................................17 The LED Lights Flicker. ........................................................................................................................17 BT12 Wireless Awning Control Kits and Components ............................................................ 18 070029-001r9 3 BT12 WIRELESS AWNING CONTROL SYSTEM INSTALLATION MANUAL CAREFREE OF COLORADO SAFETY INFORMATION This is the safety alert symbol. It is used to alert individuals to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible personal injury or death. WARNING Indicates a hazardous situation, which if not avoided, could result in death or serious bodily injury. CAUTION Indicates a hazardous situation, which if not avoided, may result in minor or moderate bodily injury. NOTICE Indicates a situation that may result in equipment-related damage. General Safety: WARNING SHOCK HAZARD. Always disconnect battery or power source before working on or around the electrical system. WARNING Always wear appropriate safety equipment (i.e. goggles). CAUTION Always use appropriate lifting devices and/or helpers when lifting or holding heavy objects. NOTICE When using fasteners, do not over tighten. Soft materials such as fiberglass and aluminum can be "stripped out" and lose the ability to grip and hold. 4 070029-001r9 CAREFREE OF COLORADO INSTALLATION MANUAL WHERE CAN BT12 BE USED BT12 WIRELESS AWNING CONTROL SYSTEM The BT12 Wireless Awning Control System can be used on the following 12V motorized Carefree awnings. Carefree Awnings Altitude Compass Eclipse Longitude Travel'r Latitude Freestyle Evolution Freestyle WM Freestyle RM Freedom WM Freedom RM Marquee BT12 YES YES YES YES YES YES YES YES YES YES YES YES Remote YES YES YES YES YES YES YES YES YES YES YES YES Motion Sensor YES YES YES YES YES YES YES YES YES NO NO NO NOTES Standard for Aftermarket Models Standard INSTALLATION WARNING SHOCK HAZARD. Always disconnect battery or power source before working on or around the electrical system. NOTICE To comply with 2015 NFPA 1192 RV Standard, Section 6.4.9, switches must be mounted as follows: For travel trailers and 5th wheels: a) Installed in a dedicated switch cabinet with a latching door; or, b) Installed with the optional covered bezel available from Carefree; or, c) Installed in a cabinet with a latching door where the switch is protected and CANNOT be activated by any items or cargo that may move or shift during transit; or, d) Installed with an interrupt circuit connected to the "IGN LOCK" (green wire). For motorized coaches (Class A, Class B and Class C): a) Installed with an interrupt circuit connected to the "IGN LOCK" (green wire). The BT12 module provides an ignition lockout option. When the "IGN LOCK" (green wire) is connected to the vehicle PCM or other switched source the following parameters are set: i) If Open = Awning Active ii) If tied to GND = RTL (Retract Then Lock) Awning retracts, extend command disabled iii) If tied to +12Vdc = Standard Extend command disabled To Start: 1. Determine the location for the awning switches, awning lights switch and BT12 control module. NOTE: The BT12 control module leads are 6" in length. If the distance between the module and the switches is greater than 6", the installer must furnish splice wires for the extra distance. Use appropriate size wire gauges. Use appropriate sized butt splices to secure connections. 2. Route the motor cable and LED harness to the location of the module. 070029-001r9 5 BT12 WIRELESS AWNING CONTROL SYSTEM INSTALLATION MANUAL BT12 CONTROL MODULE INSTALLATION (Refer to the wiring diagram on page 8.) CAREFREE OF COLORADO NOTICE Do not mount the unit near heat producing elements such as LP appliances or engine exhaust components. NOTICE For best reception, do not mount the unit near or on a metal surface. 1. Clean the mounting surface. The surface must be flat and clean for the mounting tape to properly adhere. 2. Remove the release paper from the tape on the back of the module and firmly press the module onto the mounting surface. NOTE: The module may be oriented for best fit with access to the wire leads. Mounting Tape Remove Release Paper 3. Attach the motor wires (refer to diagram for corresponding wire colors) to the module leads for the motor using 14-16awg butt splices. 4. Run a minimum 14 awg wire to chassis ground. Suitable ground would be the vehicle chassis or BT003 conductive structure connected to the chassis. Splice the wire to the module GND lead with a 14- 16awg butt splice. 5. Run a minimum 14 awg wire from the power distribution panel (auxiliary battery circuit) or equivalent. The circuit should be protected by a 15-amp fuse. Splice the wire to the module +12V lead with a 14-16awg butt splice. NOTE: If the wire run is 30 feet or longer for +12Vdc and/or GND, use 12awg wire to prevent voltage drop. Use the appropriate butt splices for the wire size. 6. Splice the Black wire from the LED Harness to the module LED GND lead (Black) with a 18-22awg butt splice. 7. Route the module LED + lead (RED) to the awning lights switch location. Use 20awg wire and 1822awg butt splice to extend the lead as necessary. 8. Route the module IGN LOCK lead (Green) to the vehicle PCM or other switch source (used for ignition lockout). 9. Route the remaining wires (Violet, Gray, Yellow and Brown) to the location for the awning control switches. Use 20awg wires and 18-22awg butt splices to extend the leads as necessary. 6 070029-001r9 CAREFREE OF COLORADO INSTALLATION MANUAL AWNING SWITCH INSTALLATION (Refer to the wiring diagram on page 8.) BT12 WIRELESS AWNING CONTROL SYSTEM 1. At the switch location cut a 2 5/16" [5.9cm) x 1 1/2" [3.8cm] hole. 2. From the module, terminate the three (3) 20awg wires (Brown, Yellow and Gray) with .187, 18-20 awg female terminals. Attach to the EXTEND/RETRACT switch as shown in the wiring diagram. ON RETRACT Optional Covered Bezel 1" [2.5cm] 2.32" [5.9cm] 3. From the module, terminate the Violet wire with a .187, 18-20 awg female terminal. Attach to the ON/OFF switch. 4. Run a minimum 14 awg wire to +12VDC. Terminate the wire with .187, 14-16 awg female terminal and connect to the second terminal of the ON/OFF switch. OFF Awning ConEtrXoTlEND ON RETRACT OFF Awning ConEtrXoTlEND [31.8.5cm" ] #6 x 1/2" Screw (x4) BT001 NOTE: If the wire run is 30 feet or longer, use 12awg wire to prevent voltage drop. Use the appropriate wire terminals for the wire size. 5. Push the wires and switches into the hole then attach the switch frame using 4 #6 x 1/2" screws. 6. Snap the switch bezel over the switch frame. AWNING LIGHTS SWITCH INSTALLATION NOTE: Carefree offers two switch options, unlighted and lighted. Installers may choose to furnish the control switch or may wire directly to a multiplexing control center. #6 x 1/2" Screw (x2) 1.13" White/Violet (20awg) To +12VDC Single Pole, Single Throw Switch ON 2.9" OFF 1.5" GND White/Violet (20awg) To +12VDC Lighted Single Throw Switch 1.88" To Multiplexing White/Violet (20awg) Controller Multiplexing Control Connection BT004d 1. Determine the location of the switch. 2. At the switch location, cut a 1 1/8" x 1 1/2" hole. 3. Wire the switch as shown. Wire terminals at the switch are .187, 18-24 awg female disconnects. NOTE: The lighted switch has a third terminal. This is wired to GND. 070029-001r9 7 BT12 WIRELESS AWNING CONTROL SYSTEM WIRING DIAGRAM INSTALLATION MANUAL CAREFREE OF COLORADO To +12VDC 1 GND Top Black F M F Red F M F Bottom A To +12VDC LED Strip 4 B Black Red 5 Red (16awg) Black (16awg) Blue (16awg) White (16awg) White/Violet (20awg) White/Black (20awg) White/Red (20awg) 3 To vehicle PCM or other switched source Control Module Violet (18awg) Green (18awg) Gray (18awg) Yellow (18awg) Brown (18awg) C 2 .187, 18-20awg Female Spade Terminals (x5) To +12VDC Extend/ On/Off Retract Rear View of Switch Assy Red (18awg) Top Black F M F Red F M F Blue (16awg) A White (16awg) B Bottom Eclipse, Travel'r, Latitude, Longitude, Altitude Blue Brown Blue (16awg) White (16awg) A B Freedom WM, Freestyle WM, Marquee Brown Blue Blue (16awg) White (16awg) A B Freedom RM, Freestyle RM DETAIL A Motor Connect MOTOR MOTOR MOTOR White/Violet (20awg) To +12VDC Single Pole, Single Throw Switch GND To +12VDC White/Violet (20awg) Lighted Single Throw Switch To Multiplexing Controller White/Violet (20awg) Multiplexing Control Connection DETAIL B Awning Lights Switch Options 3 To vehicle PCM or other switched source Violet (18awg) Green (18awg) Gray (18awg) Yellow (18awg) Brown (18awg) Awning Disable Switch M1 M2 6 +12VDC 3 To vehicle PCM or other switched source Violet (18awg) Green (18awg) Gray (18awg) Yellow (18awg) Brown (18awg) Awning Disable Switch S1 Com S2 6 +12VDC Direct Motor Control DETAIL C Multiplex Control System Dry Connectors BT002e 8 070029-001r9 CAREFREE OF COLORADO INSTALLATION MANUAL BT12 WIRELESS AWNING CONTROL SYSTEM 1 For GND, run a minimum 14 awg wire to chassis ground. Suitable ground would be the vehicle chassis or conductive structure connected to the chassis. For +12Vdc, Run a minimum 14 awg wire from the power distribution panel (auxiliary battery circuit) or equivalent. The circuit should be protected by a 15-amp fuse. NOTE: If the wire run is 30 feet or longer, use 12awg wire to prevent voltage drop. Use the appropriate wire terminals for the wire size. 2 The BT12 module leads are 6" in length. If the distance between the module and the switch is greater than 6", the installer must furnish splice wires for the extra distance. Use appropriate size wire gauges. Use appropriate sized butt splices to secure connections. 3 The BT12 module provides an ignition lockout option. When the "IGN LOCK" (green wire) is connected to the vehicle PCM or other switched source the following parameters are set: a) If Open = Awning Active b) If tied to GND = RTL (Retract Then Lock) Awning retracts, extend command disabled c) If tied to +12Vdc = Standard Extend command disabled 4 The LED connection is optional to provide LED controls through the app for white LEDS only. White LEDS can also be installed per the standard LED installation without BT12 Controls. RGB lights must be installed per the standard RGB installation. 5 Carefree LED lights uses a 2 amp circuit draw. The BT12 limits the output current to 2 amps. If using a different brand of high output LED's that draws more than 2 amps, the lights will flicker and not perform as expected. 6 The awning disable switch is a single throw; single pole switch used with OEM Multiplexing Control Systems. Switch is furnished by installer. 070029-001r9 9 BT12 WIRELESS AWNING CONTROL SYSTEM INSTALLATION MANUAL CAREFREE OF COLORADO INSTALLING THE BT MOTION SENSOR The system operates by gauging the motion of the awning's front edge (roller tube or lead rail). When the motion exceeds the preset threshold the system retracts the awning. The factory default is "3" on a scale from 1 to 5. When using the mobile app, the sensitivity can be adjusted for personal preference. The sensor is located in the motor head for vertical arms or in the lead rail for box awnings. NOTE: If this is a replacement or an upgrade, do not install the module into the bracket until it is paired to the BT12 Control Module (page 13Error! Bookmark not defined.). Altitude / Compass / Longitude 1. Remove the front cover on the motor side. The cover snaps onto the rear cover. Press in on both sides of the rear cover. Rotate the cover up and off. ORIGINAL CONFIGURATION Motion Sensor Battery Pull Tab CURRENT CONFIGURATION Thumb Tab Front Cover Thumb Tab Down Attach Bracket to Inside of Rear Cover Remove Release Paper Motion Sensor Front Cover Mounting Prongs Press on both sides Press on both sides of the rear cover to of the rear cover to release front cover release front cover BT024a BT024b Altitude Shown Altitude Shown 2. Clean the inside surface of the rear cover. 2. Slide the motion sensor into the mounting 3. Remove the module from the bracket. prongs located in the rear cover. The sensor 4. Remove the release paper from the mounting tape on the back of the bracket. must be oriented with the flange side toward the motor as shown. 5. Firmly press the bracket onto the inner surface of the rear cover. 3. Snap the front cover onto the rear cover. Hang the cover on the top and swing down until it clicks. 6. Snap the front cover onto the rear cover. Hang the cover on the top and swing down until it clicks. 10 070029-001r9 CAREFREE OF COLORADO INSTALLATION MANUAL BT12 WIRELESS AWNING CONTROL SYSTEM Latitude 1. Remove the front cover on the motor side. The cover snaps onto the rear cover. Press the bottom of the rear cover until the front cover releases then lift the front cover off. Motion Sensor ORIGINAL CONFIGURATION Battery Pull Tab CURRENT CONFIGURATION Thumb Tab Front Cover Attach Bracket to Inside of Rear Cover Motion Sensor Front Cover Mounting Prongs Thumb Tab Down Remove Release Paper Press Up On Rear Cover to Release Front Cover BT025a Press Up On Rear Cover to Release Front Cover BT025b 2. Clean the inside surface of the rear cover. 3. Remove the module from the bracket. 4. Remove the release paper from the mounting tape on the back of the bracket. 5. Firmly press the bracket onto the inner surface of the rear cover. 2. Slide the motion sensor into the mounting prongs located in the rear cover. The sensor must be oriented with the flange side away from the motor as shown. 3. Snap the front cover onto the rear cover. Hang the cover on the top and swing down until it clicks. 6. Snap the front cover onto the rear cover. Hang the cover on the top and swing down until it clicks. Eclipse / Travel'r 1. Open the awning to access the screws in the rear cover. 2. Remove the six (6) small screws and front cover and set aside. Remove Screws (x6) 3. Clean the inside surface of the motor frame. Front Cover ORIGINAL CONFIGURATION CURRENT CONFIGURATION BT026a Motor Frame Attach Bracket to Inside of Motor Frame Motor Frame Attach Sensor to Inside of Motor Frame Remove Release Paper Thumb Tab Down Battery Pull Tab Motion Sensor Thumb Tab BT026b 4. Remove the module from the bracket. 5. Remove the release paper from the mounting tape on the back of the bracket. 6. Firmly press the bracket onto the inner surface of the motor frame. Attach Double Sided Tape to Back of Sensor Then Remove Release Paper BT026c 4. Remove the release paper from the mounting tape on the back of the sensor. 5. Firmly press the sensor onto the inner surface of the motor frame. 070029-001r9 11 BT12 WIRELESS AWNING CONTROL SYSTEM Small Box Awnings INSTALLATION MANUAL CAREFREE OF COLORADO This option is available for Freestyle WM and Freestyle RM. It is not available for the Freedom WM, Freedom RM or Marquee. 1. Open the awning to expose the inside of the lead rail on the motor side. Thumb Tab ORIGINAL CONFIGURATION CURRENT CONFIGURATION Motion Sensor Battery Pull Tab Remove Release Paper #8 x .5 PHP Screw (x2) Motion Sensor Mounting Bracket BT Motion Sensor Auto-Retraction Freestyle WM Shown BT027a Freestyle WM Shown BT027b 2. Clean the inside surface of the lead rail. 2. Attach the motion sensor to the bracket using 2 3. With the module bracket oriented horizontally, #8 x .5 PHP screws. as shown, remove the release paper from the The mounting bracket is standard for the Freestyle mounting tape. awnings. If a bracket is needed, order R001679. 4. Firmly press the bracket onto the inner surface of the lead rail between the end plate and arm connector on the motor side of the awning. Mounting Bracket End Plate Ramp BT027c 12 070029-001r9 CAREFREE OF COLORADO INSTALLATION MANUAL BT12 WIRELESS AWNING CONTROL SYSTEM SETTING THE SYSTEM INTO PAIRING MODE NOTE: Kits are paired at the factory for simplified installation. Separate components that are added or used for replacements must be paired to the existing control module. NOTICE Ensure that the kits are kept together and not mixed with other kits. The pairings are unique to each control module. NOTE: The illustration shows the standard Carefree switches. Some OEM's may choose to furnish their own switches or incorporate the power and Extend/Retract controls in a multiplexing control system. The following directions are valid for all configurations. There are two methods to set the system into pairing mode. Using the Awning Retract Function: 1. Turn power to the awning ON. 2. Extend the awning. Note that the awning does not have to be opened completely. 3. Retract the awning. 4. When the awning is fully retracted, press and hold the retract switch for 3 seconds. Using the Switches: 1. Turn the awning power switch to OFF. 2. Press and hold the extend switch. 3. While holding the extend switch, turn the power switch ON. 4. Continue to hold the extend switch for 3 seconds, then release. NOTES: The awning will remain in pairing mode for 5 minutes. The BT12 control module will pair to the physically closest unpaired device first then go to working mode. Repeat the pairing for each additional device (the module remembers the devices that have been paired). Refer to the Carefree Connects Mobile App manual for setting up and pairing a smart device (such as a smart phone or tablet). Multiple devices can be paired to the awning up to a maximum of 8 peripheral devices. o Only one active BT Motion Sensor can be paired to the BT12 Control Module. o Only one active BT Remote can be paired to the BT12 Control Module. o Multiple mobile devices (smartphone or tablet) can be paired to the BT12 Module but only 1 can be active at a time. 070029-001r9 13 BT12 WIRELESS AWNING CONTROL SYSTEM INSTALLATION MANUAL CAREFREE OF COLORADO Pairing the Motion Sensor For replacements and upgrades, the motion sensor must be paired to the control module. 1. After completing the bracket installation, restore power to the awning and extend the awning using the switches. 2. Place the awning in pairing mode. 3. For Original Configurations: Remove the battery pull tab from the motion sensor. 4. For Current Configurations: Insert the batteries into the module (see page 16). 5. Hold the motion sensor next to the control module for 2-3 seconds. The module should be paired. 6. To Test: Hold the sensor vertically with the Carefree logo upright, repeatedly move the sensor vertically up and down to simulate a brisk wind. The awning should retract. 7. Mount the module. 14 070029-001r9 CAREFREE OF COLORADO INSTALLATION MANUAL Testing the Remote Functions: 1. Turn the awning and Awning Lights power switches ON. BT12 WIRELESS AWNING CONTROL SYSTEM 2. On the remote, press and release the extend button once to activate the extend function (the motor will beep once). Press and release a second time to extend the awning. Press the button again to stop the awning motion. 3. To retract, press and release the retract button. Press the button again to stop the awning motion. NOTE: The LED controls are for White LED strips that are wired to the BT12 module. 4. Extend the awning so that the LED strip is visible. 5. Turn the awning lights power switch ON. 6. Press the ON/Off button to turn the LED's on and off. 7. Press the LED Bright to brighten the LEDs. Press the LED Dim to lower the LED's 070029-001r9 15 BT12 WIRELESS AWNING CONTROL SYSTEM BATTERY REPLACEMENT INSTALLATION MANUAL CAREFREE OF COLORADO BT MOTION SENSOR If the motion sensor batteries are low, the awning will beep every 30 seconds (when the power switch is ON) and the awning will partially retract. This will continue until the batteries are replaced. The awning will operate normally after the batteries are replaced. Original Configuration Current Configuration Remove Screws and Cover Thumb Tab Remove Module From Bracket 675 Insert These Ends First PC Board (ref) Remove Old Batteries SIDE DOWN Insert New Batteries Seal (ref) Contact Tabs Note: Refer to the module installation for location in awning. BT007 The original motion sensor uses two (2) 675 batteries; batteries are available at local battery outlets. Remove Old Batteries Insert New Batteries Note: Refer to the module installation for location in awning. BT007a The current motion sensor uses two (2) "AAA" alkaline batteries; batteries are available at local battery outlets. 1. Pull the thumb tab of the bracket away from the 1. Remove the sensor module from the awning. module and lift the module out of the bracket. 2. Remove the screws and the rear cover. NOTE: It is not mounting bracket. necessary to remove the 3. Remove the two batteries. 2. Remove the two screws and the rear cover. 4. Make sure that the contact tabs are clean and bent up for best contact. 3. Remove the two batteries. 5. Insert new batteries. Match the new battery 4. Make sure that the contact tabs are clean and orientation with the old batteries. bent up for best contact. Tip: Place the battery end next to the PC board first 5. Replace the two batteries. Match the new then swivel the other end into the case. This will set battery orientation with the old batteries. the batteries firmly into the case. 6. Replace the cover and screws. 6. Check that the seal is in place and flat then 7. Snap the module into the mounting bracket. attach the rear cover with the screws removed The module will only fit one way in the bracket. previously. 7. Install the module back in the awning. BT REMOTE The remote uses one (1) CR2032 battery; batteries are available at local battery outlets. 1. Carefully remove the back cover using a coin in the slot at the bottom corner of the remote. 2. Remove the old battery and insert a new battery with the "+" terminal facing up. 3. Snap the back cover on. 16 Remove Back Cover Slot Coin CR2032 Replace Battery Match Battery Orientation BT008 070029-001r9 CAREFREE OF COLORADO FAQS INSTALLATION MANUAL BT12 WIRELESS AWNING CONTROL SYSTEM THE INDICATOR LIGHT BLINKS ON THE BT12 CONTROL BOX. o The indicator light on the control module shows the function status of the control module. o Solid ON indicates power is supplied to the control module. o One long blink and one short blink indicates power and 1 peripheral (i.e. remote or motion sensor) is paired to the module. Indicator Light o One long blink and multiple short blinks indicates power and multiple peripherals are paired to the module. The number of short blinks is based on the number of peripherals paired. o The module does not blink for being paired to the app. BT023 THE SYSTEM BEEPS AND THE AWNING PARTIALLY RETRACTS. o The motion sensor batteries are low, the awning will beep every 30 seconds (when the power switch is ON) and the awning will partially retract. This will continue until the batteries are replaced. The awning will operate normally after the batteries are replaced. Battery replacement is described on page 16 and in the awning's owner manual. THE REMOTE DOES NOT WORK. Confirm that the remote is paired. The module indicator light will blink when peripherals are attached (see description above). In the mobile app on the "Peripherals Page" confirm that the remote is connected. Green indicates the remote is connected, red indicates device is paired but not connected. No listing indicates the remote has not been paired. o Remote not paired. Refer to page 13 to pair the device. o Remote is paired but not active. The remote has an approximate operating range of 30 feet depending on obstructions (such as walls and other vehicles). Move closer to the awning and control module. o Remote is paired but not active. Batteries need to be replaced. Battery replacement is described on page 16 and in the awning's owner manual. THE LED LIGHTS FLICKER. Carefree LED lights uses a 2 amp circuit draw. The BT12 limits the output current to 2 amps. If using a different brand of high output LED's that draws more than 2 amps, the lights will flicker and not perform as expected. 070029-001r9 17 BT12 WIRELESS AWNING CONTROL SYSTEM INSTALLATION MANUAL CAREFREE OF COLORADO BT12 WIRELESS AWNING CONTROL KITS AND COMPONENTS The following kits and components are available for the BT12 Wireless Awning Control System BT Motion Sensor Superceded use item 4 ON RETRACT ON RETRACT OFF Awning ConEtrXoTlEND 1 Switch Kit R019468-006 OFF Awning ConEtrXoTlEND 2 Cover Bezel Kit SR0115 3 BT12 Control Module R060780-001 4 BT Motion Sensor R060808-001 5 BT Remote R001911 BT501b AVAILABLE UPGRADE KITS Kit Number Included Components R001911 1 ON RETRACT OFF Awning ConEtrXoTlEND 2 ON RETRACT OFF Awning ConEtrXoTlEND 3 4 5 Included SR0115 Included 901602 Included Included 901604 Included Included Included 901605 Included Included Included 901606 NOTES: Included Included Included Included Kits are paired at the factory. Separate components that are added or used for replacements must be paired to the existing control module. 18 070029-001r9Acrobat Distiller 10.1.16 (Windows)