User Manual for Westinghouse models including: iGen4500, Digital Inverter Generator, 3700 Running Watts 4500 Peak Watts

PDF USER

INTRODUCTION. WARNING: Operating, servicing, and maintaining this equipment can expose you to chemicals including engine exhaust, carbon monoxide, phthalates, and lead, which are known to the...

iGen 4500 - m.media-amazon.com

are used throughout this manual to highlight important information. Make sure that the meanings of this safety information is known to all who operate, perform mantainence on, or are near the generator. This safety alert symbol appears with most safety statements. It means attention, become alert, your safety is involved! Please read and

m.media-amazon.com › images › IiGen 4500 - m.media-amazon.com

Not Your Device? Search For Manuals / Datasheets:

File Info : application/pdf, 32 Pages, 6.49MB

Document
Current View
C1F2klTf8uS
USER MANUAL
iGen4500
Digital Inverter Generator
Gasoline: 3700 Running Watts | 4500 Peak Watts
DO NOT RETURN THIS PRODUCT TO THE STORE
If you have questions or need assistance, please call customer service at 855-944-3571.

INTRODUCTION

TABLE OF CONTENTS INTRODUCTION
DISCLAIMERS ........................................................................2 ALL RIGHTS RESERVED.......................................................2 SPECIFICATIONS...................................................................3
SAFETY
SAFETY DEFINITIONS...........................................................4 SAFETY SYMBOLS ................................................................4 SAFETY INSTRUCTIONS ......................................................5 SAFETY LABELS AND DECALS ............................................7
COMPONENTS
CONTROL PANEL COMPONENTS........................................8 GENERATOR COMPONENTS ..............................................9 DIGITAL DATA CENTER .........................................................9
ASSEMBLY
CARTON CONTENTS ..........................................................10 INITIAL OIL FILL ...................................................................10 FUEL .....................................................................................11 CONNECT THE BATTERY ...................................................12
OPERATION
GENERATOR LOCATION.....................................................13 GROUNDING ........................................................................13 HIGH ALTITUDE OPERATION .............................................13 REMOTE START ..................................................................14 FUEL SWITCH .....................................................................14 BREAK-IN PERIOD ..............................................................14 FREQUENCY OF USE .........................................................14 BEFORE STARTING THE GENERATOR .............................14 STARTING THE ENGINE .....................................................14

STOPPING THE ENGINE.....................................................15 ECO MODE...........................................................................15 AC CIRCUIT BREAKERS .....................................................15 OVERLOAD RESET .............................................................15 POWER MANAGEMENT ......................................................16 EXTENSION CORDS ...........................................................16 PARALLEL OPERATION.......................................................17 TRANSPORTING ..................................................................18
MAINTENANCE
MAINTENANCE SCHEDULE ...............................................19 MAINTENANCE REPLACEMENT PARTS ...........................19 ENGINE SERVICE COVER ..................................................19 AIR FILTER MAINTENANCE ................................................19 ENGINE OIL LEVEL CHECK ................................................20 ENGINE OIL CHANGE .........................................................21 SPARK PLUG MAINTENANCE ............................................21 SPARK ARRESTOR SERVICE .............................................22 BATTERY MAINTENANCE ...................................................22 BATTERY REPLACEMENT ..................................................22 STORAGE .............................................................................23 VALVE CLEARANCE ............................................................24 MANUAL CHOKE OPERATION............................................24
TROUBLESHOOTING ....................................................25 EXPLODED VIEWS AND PARTS LISTS
ENGINE EXPLODED VIEW..................................................26 ENGINE PARTS LIST ...........................................................27 GENERATOR EXPLODED VIEW .........................................29 GENERATOR PARTS LIST...................................................30
SCHEMATICS ....................................................................32

INTRODUCTION
WARNING: Operating, servicing, and maintaining this equipment can expose you to chemicals including engine exhaust, carbon monoxide, phthalates, and lead, which are known to the State of California to cause cancer and birth defects or other reproductive harm. To minimize exposure, avoid breathing exhaust, and wear gloves or wash your hands frequently when servicing this equipment. For more information go to www. P65warnings.ca.gov.

ALL RIGHTS RESERVED
All rights reserved. No reproduction allowed in any form without written permission from Westinghouse Outdoor Power Equipment, LLC.
Read this manual before using or performing maintenance on this product. Failure to follow the instructions and safety precautions in this manual can result in serious injury or death.

DISCLAIMERS
All information, illustrations, and specifications in this manual were in effect at the time of publishing. The illustrations used in this manual are intended as representative reference views only. We reserve the right to make any specification or design change without notice.

SAVE THESE INSTRUCTIONS

2 | Westinghouse Outdoor Power Equipment, LLC

INTRODUCTION

SPECIFICATIONS

Specifications

iGen4500

Running Watts: 3700

Peak Watts: 4500

Rated Voltage: 120V

Rated frequency: 60 Hz

Phase: Single phase

Total Harmonic Distortion:

 3%

Engine Displacement: 224 cc

Starting Type:

Recoil, Electric Start, Remote

Fuel Capacity: 3.4 Gallons (12.8 Liters)

Fuel Type: 87­93 octane*

Oil Capacity: 0.63 US qt (0.60 L)

Oil Type: 10W-30

Spark Plug: 97109 - F7RTC

Spark Plug Gap:

0.024 - 0.032 in. (0.60 - 0.80 mm)

Valve Intake 0.0031 ­ 0.0047 in Clearance: (0.08 ­ 0.12 mm)

Valve Exhaust 0.0051 ­ 0.0067 in Clearance: (0.13 ­ 0.17 mm)

AC Grounding System: Floating neutral

Voltage Regulator: Digital

Alternator Type: Permanent magnet

Maximum Ambient Temperature:

104°F (40°C)

· EPA Certifications: · CARB
· CSA Group

*Ethanol content of 10% or less. DO NOT use E15 or E85.

UPDATES
The latest User Manual for your Westinghouse generator can be found under our support tab. https:// westinghouseoutdoorpower.com/pages/manuals
Or scan the following QR code with your smartphone camera to be directed to the link.

NOTICE
This product is designed and rated for continuous operation at ambient temperatures up to 104°F (40°C). If needed, this product can be operated at temperatures ranging from 5°F (15°C)­122°F (50°C) for short periods. If the product is exposed to temperatures outside of this range during storage, it should be brought back within this range before operation. This product must always be operated outdoors in a well-ventilated area and far away from doors, windows, and other vents. Maximum wattage and current are subject to and limited by such factors as fuel BTU content, ambient temperature, altitude, engine conditions, etc. Maximum power decreases about 3.5% for each 1,000 feet above sea level, and will also decrease about 1% for each 10°F (6°C) above 60°F (16°C) ambient temperature.
PRODUCT REGISTRATION
For trouble-free warranty coverage, it is important to register your Westinghouse generator. You can register by:
· Completing and mailing the product registration card included in the carton.
· Registering your product online at: https://westinghouseoutdoorpower.com/pages/ warranty-registration
· Scanning the following QR code with your smartphone camera. You will be directed to the mobile registration link.
· Sending the following product information to: Westinghouse Outdoor Power Warranty registration 777 Manor Park Drive Columbus, OH 43228
For Your Records Date of Purchase:

Model Number:

Serial Number:

Place of Purchase:

IMPORTANT: Keep your purchase receipt for trouble-free warranty coverage.

Westinghouse Outdoor Power Equipment, LLC | 3

SAFETY

SAFETY
SAFETY DEFINITIONS
The words DANGER, WARNING, CAUTION and NOTICE are used throughout this manual to highlight important information. Make sure that the meanings of this safety information is known to all who operate, perform mantainence on, or are near the generator.
This safety alert symbol appears with most safety statements. It means attention, become alert, your safety is involved! Please read and abide by the message that follows the safety alerts symbol.

SAFETY SYMBOLS

Follow all safety information contained in this manual and on the generator.

Symbol

Description

Safety Alert Symbol

Electrocution Hazard

Asphyxiation Hazard

Burn Hazard. Do not touch hot surfaces.

Indicates a hazardous situation which, if not avoided, will result in death or serious injury.
Indicates a hazardous situation which, if not avoided, could result in death or serious injury.
Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.
NOTICE
Indicates a situation which can cause damage to the generator, personal property, and/or the environment, or cause the equipment to operate improperly. Note: Indicates a procedure, practice or condition
that should be followed for the generator to function in the manner intended.

Electrical Shock Hazard Fire Hazard Maintain Safe Distance Lifting Hazard Read Manufacturer's Instructions Do Not Operate in Wet Conditions

4 | Westinghouse Outdoor Power Equipment, LLC

SAFETY INSTRUCTIONS
CORRECT USAGE Example location to reduce risk of carbon monoxide poisoning · ONLY use outside and downwind, far away
from windows, doors and vents. · Direct exhaust away from occupied spaces
INCORRECT USAGE Do not operate in any of the following locations: · Near any door, window, or vent · Garage · Basement · Crawl Space · Living Area · Attic · Entry Way · Porch · Mudroom

SAFETY

NOTICE
Install battery-powered carbon monoxide detectors or plug-in carbon monoxide detectors with battery back-up in living areas.

Fire and electrocution hazard. Do not connect to a building's electrical system unless the generator and transfer switch have been properly installed and the electrical output has been verified by a qualified electrician. The connection must isolate the generator power from utility power and must comply with all applicable laws and electrical codes.

Electrocution hazard. Never use the generator in a location that is wet or damp. Never expose the generator to rain, snow, water spray, or standing water while in use. Protect the generator from all hazardous weather conditions. Moisture or ice can cause a short circuit or other malfunction in the electrical circuit.

Westinghouse Outdoor Power Equipment, LLC | 5

SAFETY

GENERAL SAFETY PRECAUTIONS
· Never use the generator to power medical support equipment.
· Do not operate the generator when you are tired or under the influence of drugs, alcohol, or medication.
· Do not use generator with electrical cords which are worn, frayed, bare, or otherwise damaged.
· All electrical tools and appliances operated from this generator must be properly grounded by use of a third wire or be double-insulated.
· When this generator is used to supply a building wiring system the generator must be installed by a qualified electrician and connected to a transfer switch as a separately derived system in accordance with NFPA 70, National Electrical Code.
· If you begin to feel sick, dizzy, or weak while using the generator, move to fresh air IMMEDIATELY. See a doctor, as you can have carbon monoxide poisoning.
· Only use OUTSIDE and far away from windows, doors, and vents as recommended by the US Department of Health and Human Services Centers for Disease Control and Prevention. Your specific home and/or wind conditions may require additional distance.
· While operating and storing, keep at least 5 feet of clearance on all sides of the generator, including overhead. Allow the generator to cool a minimum of 30 minutes before storage. Heat created by the muffler and exhaust gases could be hot enough to cause serious burns and/or ignite combustible objects.
· Do not touch the muffler or engine. They are very HOT and will cause severe burns. Do not put body parts or any flammable or combustible materials in the direct path of the exhaust.
· Always remove any tools or other service equipment used during maintenance away from the generator before operating.
· Avoid skin contact with engine oil or gasoline. Wear protective clothing and equipment. Wash all exposed skin with soap and water.
FUEL SAFETY
· Store fuel in a container approved for gasoline.
· Do not smoke when filling the generator with gasoline. · Do not allow the generator's gas tank to overflow when
filling. · Shut down the engine and allow it to cool for five
minutes before adding gasoline or oil to the generator.
· Never remove the fuel cap when the generator is running. Shut off the engine and allow the unit to cool at least five minutes. Remove the fuel cap slowly to release pressure, keep fuel from escaping around the cap, and to avoid the heat from the muffler igniting fuel vapors. Tighten the fuel cap securely after refueling.

· Wipe spilled fuel from the unit.
· Never attempt to burn off spilled fuel.
· Never overfill the fuel tank. Leave room for fuel to expand. Overfilling the fuel tank can result in a sudden overflow of gasoline and result in spilled gasoline coming in contact with HOT surfaces.
· Spilled fuel can ignite. If fuel is spilled on the generator, wipe up any spills immediately. Dispose of rag properly. Allow area of spilled fuel to dry before operating the generator.
· Wear eye protection while refueling.
· Never use gasoline as a cleaning agent.
· Store any containers containing gasoline in a wellventilated area, away from any combustibles or source of ignition.
GASOLINE AND GASOLINE VAPOR (GAS)
Fire and explosion hazard. Gasoline is highly explosive and flammable and can cause severe burns or death. · In case of a gas fire, do not attempt to extinguish the
flame if the fuel valve is in the gas position. Introducing an extinguisher to a generator with an open fuel valve could create an explosion hazard.
· Gas has a distinctive odor, this will help detect potential leaks quickly.
· Gas vapors can cause a fire if ignited. · Gasoline is a skin irritant and needs to be cleaned up
immediately if it comes in contact with the skin. When starting the generator: · Make sure that the fuel cap, air filter, spark plug, fuel
lines, and exhaust system are properly in place.
· If you spill any gasoline on the tank, allow it to fully evaporate before operating.
· Make sure the generator is on a flat surface before operating.
When transporting or servicing the generator: · Disconnect the spark plug wire to prevent accidental
starting. When storing the generator: · Store away from sparks, open flames, pilot lights, heat,
and other sources of ignition.
· Do not store gas near furnaces, water heaters, or any other appliances that produce heat or have automatic ignitions.

6 | Westinghouse Outdoor Power Equipment, LLC

SAFETY LABELS AND DECALS

SAFETY

Westinghouse Outdoor Power Equipment, LLC | 7

COMPONENTS
COMPONENTS
CONTROL PANEL COMPONENTS

1. Ground Terminal: The ground terminal is used to externally ground the generator.
2. 120 Volt AC, 20 Amp Duplex NEMA 5-20R Receptacle: Receptacle can supply a maximum of 20 Amps.
3. Parallel Operation Outlets: A compatible Westinghouse Inverter Generator can be connected for additional power output.
4. LED Data Center: Displays remaining run time (F), power output in kW (P), fuel level in liters (L), voltage output (V), and lifetime hours.
5. Overload Reset: The generator inverter will automatically switch OFF all AC output to protect the generator if overloaded or if there is a short circuit in a connected appliance.
6. USB Ports: Two-port 5V/2.1A USB outlet. Accepts Type A USB plugs.
7. Low Oil LED: Indicates low oil level. When the oil level in the crankcase falls below the safe operating limit, the low oil level indicator will illuminate and the generator will automatically shut off the engine.
8. Overload LED: Indicates that the generator is overloaded. See page 17.
9. Output Ready LED: Illuminates when the generator is operating normally. Indicates the generator is producing electrical power at the receptacles.
8 | Westinghouse Outdoor Power Equipment, LLC

10. Fuel Switch: Used to turn gas valve open or closed. 11. Battery Indicator: Indicates that power is ON. Light
will remain illuminated while the unit is ON.
12. Battery Charging Port: Used to charge the battery with the included battery charger.
13. Main Circuit Breaker: The main circuit breaker controls total output of all outlets to protect the generator from overload or short circuit.
14. Eco Mode: Eco mode minimizes fuel consumption and noise by adjusting the engine RPM to the minimum required for the current load.
15. Push-Button Start/Stop: Push once to automatically start the engine. Push again to stop the engine.
16. Battery Switch: Turns battery ON and OFF. Must be ON before electric start or remote start.
17. 20 Amp AC Circuit Breaker: Circuit breaker limits the current that can be delivered through the NEMA 5-20R receptacle to 20 Amps.
18. 30 Amp AC Circuit Breaker: Circuit breaker limits the current that can be delivered through the NEMA TT-30 receptacle to 30 Amps.
19. 120 Volt AC, 30 Amp NEMA TT-30R Receptacle: Receptacle can supply a maximum of 30 Amps.

GENERATOR COMPONENTS

COMPONENTS

1. Fuel Cap: Add unleaded fuel here. Close the cap until it clicks.
2. Engine Service Cover: Cover provides access to the engine, air cleaner, carburetor, and spark plug.
3. Transport Wheels: Wheels allow one-handed maneuverability when used with the extendable handle.
4. Extendable Handle: Extend and retract the handle by pushing the locking button.
5. Carry Handles: Built-in handles allow easy, twoperson transport.
DIGITAL DATA CENTER
Fuel remaining and power output percentage LEDs are continuously displayed. Push the Mode button to cycle through the data display modes.

6. Recoil Handle: Pull the recoil handle to manually start the engine.
7. Control Panel: The control panel contains the outlets and operational controls.
8. Oil Access Cover: Cover provides access to the oil fill cap/dipstick and oil drain plug.
9. Battery Access Cover: Cover provides access to the battery and quick-connect plug.
10. Muffler and Spark Arrestor: The spark arrestor prevents sparks from exiting the muffler.
11. Model Information Label: Provides model serial number, voltage/amps, and power rating information.

Westinghouse Outdoor Power Equipment, LLC | 9

ASSEMBLY
ASSEMBLY
CARTON CONTENTS

Weight hazard. Always have assistance when lifting the generator.

1. Carefully open the carton.

2. Remove and save the instruction manual, oil bottle, oil 1. On a level surface, remove the oil access cover and oil

funnel, spark plug socket wrench, and battery charger.

dipstick.

3. Remove and discard the packing tray.

4. Unfold the top of the plastic bag enclosing the generator.

5. Carefully cut the vertical corners of the carton to access the generator.

6. Recycle or dispose of the packaging materials properly.

CARTON CONTENTS · User manual · Quick Start Guide · Remote start key fob (attached to recoil starter) · Bottle of SAE 10W-30 Oil · Battery charger · Spark plug wrench · Oil Funnel
· Screwdriver If any parts are missing, contact our service team at service@wpowereq.com or call 1-855-944-3571.
INITIAL OIL FILL

2. Using the supplied funnel and oil, add oil into the engine.
Note: As residual oil from the factory may remain in the engine, add the oil incrementally near the end of the bottle to prevent overfilling the engine. See Engine Oil Level Check in the Maintenance section.
3. Replace the oil dipstick and hand-tighten.
4. Replace the oil access cover.

NOTICE
THIS GENERATOR HAS BEEN SHIPPED WITHOUT OIL. Do not attempt to crank or start engine before it has been properly serviced with recommended oil. Failure to add engine oil before starting will result in serious engine damage.

NOTICE
Use of 2-stroke/cycle oil or other unapproved oil types can cause severe engine damage that is not covered under warranty.
The included, recommended oil type for typical use is 10W-30 engine oil. If running the generator in extreme temperatures, refer to the following chart.

10 | Westinghouse Outdoor Power Equipment, LLC

ASSEMBLY

FUEL
Fire and explosion hazard. Never use a gasoline container, gasoline tank, or any other fuel item that is broken, cut, torn or damaged.
Fire and explosion hazard. Do not overfill fuel tank. Fill only to the red fill ring located in the in-tank fuel screen filter. Overfilling may cause fuel to spill onto engine causing a fire or explosion hazard.
Fire and explosion hazard. Never refuel the generator while the engine is running. Always turn the engine off and allow the generator to cool for two minutes before refueling.
NOTICE
Do not use E15 or E85 fuel in this product. Engine or equipment damage caused by stale fuel or the use of unapproved fuels (such as E15 or E85 ethanol blends) is not covered by warranty. Only use unleaded gasoline containing up to 10% ethanol.

FUEL REQUIREMENTS
· CLEAN, FRESH, unleaded gasoline, 87­93 octane.
· Up to 10% ethanol (gasohol) is acceptable (where available; non-ethanol fuel is recommended).
· DO NOT use E85 or E15.
· DO NOT use a gas oil mix.
· DO NOT modify the engine to run on alternate fuels.
· DO NOT fuel indoors.
· DO NOT create a spark or flame while fueling.
USING FUEL STABILIZER Adding a fuel stabilizer (not included) extends the usable life of fuel and helps prevent deposits from forming that can clog the fuel system. Follow the manufacturer's instructions for use.
Always mix the correct amount of fuel stabilizer to gasoline in an approved gasoline container before fueling the generator. Run the generator for five minutes to allow the stabilizer to treat the entire fuel system.
FILLING THE FUEL TANK
1. Turn the generator OFF and allow to cool for a minimum of two minutes before fueling.
2. Place the generator on level ground in a well ventilated area.
3. Clean area around fuel cap and remove the cap slowly.
NOTICE
Only fill the tank from an approved gasoline container. Make sure the gasoline container is internally clean and in good condition to prevent fuel system contamination.
4. Slowly add the recommended fuel. Do not overfill. Fill only to the red maximum fill ring on the fuel screen filter visible in the filler neck.

Westinghouse Outdoor Power Equipment, LLC | 11

ASSEMBLY

5. Install the fuel cap and tighten until a click is heard.
NOTICE
Fuel can damage paint and plastic. Use caution when filling the fuel tank. Damage caused by spilled fuel is not covered under warranty.

4. Align the tabs on the bottom of the battery access cover with the generator case then push to reinstall the cover.
Note: The generator is equipped with a battery charging feature. Once the engine is running, a small charge will slowly recharge the battery.

NOTICE
Clean the fuel screen filter of debris before and after each fueling. Remove the fuel screen filter by slightly compressing it while removing it from the fuel tank.
CONNECT THE BATTERY
1. Push down the battery access cover tab and pull the cover forward to remove it.

2. Verify that the rubber battery strap is firmly securing the battery in place. If loose, pull on the strap and hook it onto the mounting base.
Note: If the strap is loose behind the battery, remove the battery, reconnect the strap, replace the battery, then thread the strap under the battery quick connect cables.
3. A quick-connect battery plug is pre-installed on the battery. Remove the cable tie securing the plugs then push firmly to connect them.
12 | Westinghouse Outdoor Power Equipment, LLC

OPERATION

OPERATION

GENERATOR LOCATION
Read and understand all safety information before starting the generator.

Asphyxiation hazard. Place the generator in a well-
ventilated area. DO NOT place the generator near vents
or intakes where exhaust fumes could be drawn into occupied or confined spaces. Carefully consider wind and air currents when positioning generator.

GROUNDING

NEVER operate the generator inside any building, including garages, basements, crawlspaces, sheds, enclosure, or compartment, including the generator compartment of a recreational vehicle.
Electrocution hazard. Never use the generator in a location that is wet or damp. Never expose the generator to rain, snow, water spray, or standing water while in use. Protect the generator from all hazardous weather conditions. Moisture or ice can cause a short circuit or other malfunction in the electrical circuit. Using a generator or electrical appliance in wet conditions, such as rain or snow, or near a pool or sprinkler system, or when your hands are wet, could result in electrocution

Shock hazard. Failure to properly ground the generator can result in electric shock.
The generator neutral is floating. The generator ground terminal is connected to the frame of the generator, the metal non-current-carrying parts of the generator, and the ground terminals of each receptacle. The generator (stator winding) is isolated from the frame and from the AC receptacle ground pin. Electrical devices that require a grounded receptacle pin connection may not function properly.
If this generator will be used only with cord and plug equipment connected to the receptacles mounted on the generator, National Electric Code does not require that the unit be grounded. However, other methods of using the generator may require grounding to reduce the risk of shock or electrocution.
Before using the ground terminal, consult a qualified electrician, electrical inspector, or local agency having jurisdiction for local codes or ordinances that apply to the intended use of the generator.
NOTICE
Only use grounded 3-prong extension cords, tools, and appliances, or double-insulated tools and appliances.

Fire hazard. Only operate the generator on a solid, level surface. Operating the generator on a surface with loose material such as sand or grass clippings can cause debris to be ingested by the generator that could block cooling vents or the air intake system. Allow the generator to cool for 30 minutes before transport or storage.
The generator should be on a flat, level surface at all times (Even while not in operation). The generator must have at least 5 ft. (1.5 m) of clearance from all combustible material.
Do not operate the generator in the back of a SUV, camper, trailer, truck bed (regular, flat, or otherwise), under stairs, next to walls or buildings, or in any other location that will not allow for adequate cooling of the generator and/or the muffler. DO NOT contain generators during operation.

HIGH ALTITUDE OPERATION
Engine power is reduced the higher you operate above sea level. Output will be reduced approximately 3.5% for every 1000 feet of increased altitude from sea level.
High altitude adjustment is required for operation at altitudes over 5,000 ft. (1524 m). Operation without this adjustment will cause decreased performance, increased fuel consumption, and increased emissions. Operation of the engine at altitudes below 2,000 ft. (762 m) with the high altitude kit is not recommended.
NOTICE
Do not operate the generator at altitudes below 2,000 ft. (762 m) with the high altitude kit installed. Engine damage may occur.
High Altitude Carburetor Kit: Part# 518913-01

Westinghouse Outdoor Power Equipment, LLC | 13

OPERATION

REMOTE START

FUEL SWITCH
Turn the fuel switch fully to the right for gasoline operation.

Verify that the area around the generator is clear before remote starting the generator.

The remote start key fob included with the generator should be attached to the recoil handle or control panel. If your unit was shipped without a key fob, contact Westinghouse customer service.
The generator can be started remotely from up to 99 feet (30 meter) using the remote start key fob.

Turn the fuel switch fully to the left to shut the fuel valve OFF.

Note: As the batteries in the remote start key fob drain, operational distance will decrease.

Remote replacement batteries: (2) CR2016 Replacement remote: Part# 130172
REPROGRAMMING THE REMOTE START
If the remote start key fob is replaced or needs re-paired to the generator, follow this procedure.
1. Turn the generator battery switch to the ON position. 2. Push and hold the ON/OFF button for 10 seconds, then
release. The start indicator light will flash green.

BREAK-IN PERIOD
For proper break-in, do not exceed 50% of the rated running watts (1850 watts) during the first five hours of operation.
Vary the load occasionally to allow stator windings to heat and cool and help seat the piston rings.
FREQUENCY OF USE
If the generator will be used on an infrequent or intermittent basis (more than one month before next use), refer to the Battery Maintenance and Storage sections of this manual for information regarding battery and fuel deterioration.

BEFORE STARTING THE GENERATOR

3. Push the ON button on the remote start key fob. It will pair with generator automatically and the start indicator
light on the generator will stop flashing.

· Verify that the generator is placed in an safe, appropriate location.
· Make sure the generator is on a dry, flat, and level surface.
· Verify that the engine is filled with oil. · Verify that all loads are disconnected.

14 | Westinghouse Outdoor Power Equipment, LLC

Fire and explosion hazard. DO NOT move or tip the generator during operation.
STARTING THE ENGINE
1. Verify that fuel is in the gas tank.
2. Turn the fuel switch to the ON position.
3. Push the battery switch to the ON position.
4. Choose the starting method:
a. Recoil Start: Firmly grasp and pull the recoil handle slowly until you feel increased resistance, then pull rapidly.

OPERATION

b. Remote Start: Push and hold the ON button on the not exceed the rated load capacity of the circuit before

remote start key fob for one second.

resetting the AC circuit breaker ON.

c. Push-Button Start: Push and hold the engine start

ON

button for two seconds.

STOPPING THE ENGINE
1. Turn off and unplug all connected electrical loads. Never start or stop the generator with electrical devices connected.
2. Let the generator run with no load for several minutes to stabilize internal temperatures.
3. Push and hold the ON/OFF button for one second or push OFF on the remote start key fob for one second.
4. Push the battery switch to the OFF position.
Note: If the engine will not be used for two weeks or longer, refer to the Storage section for correct engine and fuel storage procedures.

OFF

Push to Reset

OVERLOAD RESET
The generator will automatically switch OFF all AC output to protect the generator if overloaded or if there is a short circuit in a connected appliance. However, the engine will continue to run. Marginal overloading that temporarily illuminates the OVERLOAD LED may shorten the service life of the generator.
OVERLOAD on the control panel will illuminate red and the green OUTPUT READY will be OFF.

ECO MODE

NOTICE
Always start the generator with ECO MODE OFF. Allow the engine speed to stabilize and the OUTPUT READY LED to illuminate before switching ECO MODE ON.

Note: Do not use ECO MODE when in parallel operation with another Westinghouse generator.
ECO MODE minimizes fuel consumption and noise by adjusting the engine RPM to the minimum required for the current load.
Turn ECO MODE ON when powering small appliances with continuous loads such as a computer or electric light.
Turn ECO MODE OFF when powering large surge loads such as an air conditioner or electric pump.
To turn on ECO MODE, verify that the OUTPUT READY LED is illuminated green, then push the switch to the ON position. If no load is present, the generator RPM will drop to idle speed. The generator will detect loads as they are applied and increase engine RPM.
To run the generator at maximum power and RPM, push the ECO MODE switch to the OFF position.
AC CIRCUIT BREAKERS
The circuit breakers will automatically switch OFF if there is a short circuit or a significant overload of the generator at each receptacle. The main circuit breaker will automatically switch OFF if the combined load of the receptacles exceeds 31 Amps.
If an AC circuit breaker switches OFF automatically, check that the appliance is working correctly and it does

To restore AC output:
1. Turn off and unplug all connected electrical loads.
2. Push the RESET button on the control panel until the OVERLOAD LED goes OFF and the OUTPUT READY LED is illuminated.
3. Reset the circuit breakers if OFF.
4. Verify that the intended running and surge loads do not exceed the generator's capacity.
5. Reconnect electrical loads sequentially, allowing the generator to stabilize after each load is connected.
GENERATOR CAPACITY
NOTICE
Do not overload the generator's capacity. Exceeding the generator's wattage/amperage capacity can damage the generator and/or electrical devices connected to it. Make sure the generator can supply enough continuous (running) and surge (starting) watts for the items you will power at the same time. The total power requirements (Volts x Amps = Watts) of all

Westinghouse Outdoor Power Equipment, LLC | 15

OPERATION

appliances connected must be considered. Appliance and power tool manufacturers usually list rating information near the model or serial number.
To determine power requirements:

1. Select the items you will power at the same time.

2. Total the continuous (running) watts of these items. This is the amount of power the generator must produce
to keep the items running. See the wattage reference
chart on the next page.

3. Estimate how many surge (starting) watts you will need. Surge wattage is the short burst of power needed to start electric motor-driven tools or appliances such as a circular saw or refrigerator. Because not all motors start at the same time, total surge watts can be estimated by adding only the item(s) with the highest additional surge watts to the total rated watts from step 2.

Example:
Tool or Appliance
RV Air Conditioner (11,000 BTU) TV (Tube Type) RV Refrigerator Radio Light (75 Watts) Coffee Maker

Running Watts* 1010
300 180 200 300 600 2590 Total Running Watts*

Starting Watts* 1600
0
600
0
0
0
1600 Highest Starting Watts*

Total Running Watts Highest Starting Watts Total Starting Watts Needed *Wattages listed are approximate. Verify actual wattage.

2590 + 1600
4190

4. Plug in and turn on the next load.

5. Again, permit the generator to stabilize.

6. Repeat steps 4 and 5 for each additional load.

Wattage Reference

Tool or Appliance

Estimated Running Watts*

Estimated Starting Watts*

Incandescent Lights (4 Quantity x 75 Watts)

300

0

TV (Tube Type)

300

0

Sump Pump (1/3 hp)

800

1300

Refrigerator or Freezer

700

2200

Well Pump (1/3 hp)

1000

2000

Furnace (1/2 hp)

800

2350

Radio

200

0

Drill (3/8", 4 amps)

440

600

Circular Saw (Heavy Duty, 7-1/4")

1400

2300

Miter Saw (10")

1800

1800

Table Saw (10")

2000

2000

*Wattages listed are approximate. Verify actual wattage.

EXTENSION CORDS

Asphyxiation hazard. Extension cords running directly into the home increase the risk of carbon monoxide poisoning through any openings. If an extension cord running directly into your home is used to power indoor items, there is a risk of carbon monoxide poisoning to people inside the home. Always use battery-powered carbon monoxide detector (s) that meet current UL 2034 safety standards when running the generator. Regularly check the detector (s) battery.

POWER MANAGEMENT
To prolong the life of the generator and attached devices, use care when adding electrical loads to the generator. There should be nothing connected to the generator outlets before starting the engine. The correct and safe way to manage generator power is to sequentially add loads as follows:

Asphyxiation hazard. When operating the generator with extension cords, make sure the generator is located in an open, outdoor area, far away from occupied spaces with exhaust pointed away.

1. With nothing connected to the generator, start the engine as described in this manual.
2. Plug in and turn on the first load, preferably the largest load you have.
3. Permit the generator output to stabilize (engine runs smoothly and attached device operates properly).

Fire and electrocution hazard. Never use worn or damaged extension cords. Damaged or overloaded extension cords could overheat, arc, and burn resulting in death or serious injury.
Before connecting an AC appliance or power cord to the generator:
· Use grounded 3-prong extension cords, tools, and

16 | Westinghouse Outdoor Power Equipment, LLC

OPERATION

appliances, or double-insulated tools and appliances.
· Make sure the tool or appliance is in good working order. Faulty appliances or power cords can create a potential for electric shock.
· Make sure the electrical rating of the tool or appliance does not exceed the rated power of the generator or the receptacle being used.
EXTENSION CORD SIZING
Only use grounded 3-prong extension cords marked for outdoor use that are rated for the electrical load.

separately) is also compatible. This cord can be purchased from an authorized Westinghouse Generator dealer.
Note: Compatible Westinghouse generators without parallel ports can be operated in parallel with the receptacle-mounted parallel cable, Part# 260041.
NOTICE
DO NOT use ECO MODE during parallel operation if powering large surge loads such as an air conditioner or electric pump. Engine rpm may not adjust quickly enough to provide the voltage requirements of large surge loads, causing damage to the devices or the generators.

PARALLEL OPERATION
Fire and electrocution hazard. Never connect or disconnect the parallel cord leads when a generator is running.

1. On both generators, make sure the engine/fuel switch and the ECO MODE switch are in the OFF position.
2. Connect two parallel cable leads to the parallel outlets on the first generator, then connect the opposite cable leads to the other generator's parallel outlets.
Note: If powering devices directly from the generators (not connected to a building's transfer switch), you do not need to match the left/right cables to the generator's parallel outlets.
3. Start one of the generators and wait until the OUTPUT READY LED illuminates.
4. Start the second generator and wait until the OUTPUT READY LED illuminates before connecting a load.
5. Connect additional loads as described in Power Management section.
6. Unplug all loads before stopping the generators.

Correct connection of the left and right cables is very important when the generators are used with a transfer switch to suppy power to a building. To avoid serious personal injury or damage to electrical devices, including the generators, do not try to power an electrical system in a building without using an approved transfer switch.
NOTICE
Connecting to a generator that is not compatible can cause a low voltage output that can damage tools and appliances powered by the generator.
Parallel operation gives you the ability to link to a compatible Westinghouse Inverter Generator with the included parallel cord for combined running and peak power output.
A Westinghouse 507PC parallel cord (purchased

Westinghouse Outdoor Power Equipment, LLC | 17

OPERATION
TRANSPORTING
Weight hazard. Always have assistance when lifting the generator. · Allow the generator to cool a minimum of 30 minutes
before transporting. · Replace all protective covers on the generator control
panel. · Only use the generator's fixed handle(s) to lift the unit
or attach any load restraints such as ropes or tie-down straps. Do not attempt to lift or secure the generator by holding onto any of its other components. · Keep the unit level during transport to minimize the possibility of fuel leakage or, if possible, drain the fuel or run the engine until the fuel tank is empty before transport. · The generator wheels are only intended for hand transport. The wheels are not suitable for towing the generator either on or off-road. · Use the extendable handle for one-person, hand transport. To deploy the handle, push on the locking button and pull on the handle until it's fully extended. To stow it, push on the locking button and push on the handle until it's fully retracted. Only extend or retract the handle while the generator is OFF, stationary, and resting on a horizontal surface. Do not use the extendable handle to lift the generator entirely off the ground, tow it, or up-end it.
Fire hazard. Do not fully up-end the generator. Fuel or oil can leak and damage to the generator may occur.
18 | Westinghouse Outdoor Power Equipment, LLC

MAINTENANCE

MAINTENANCE
MAINTENANCE SCHEDULE
Regular maintenance will improve performance and extend the service life of the generator. Follow the hourly or calendar intervals, whichever occurs first. More frequent service is required when operating in adverse conditions as noted below.

ENGINE SERVICE COVER
Remove the engine service cover to access the air filter, carburetor, and spark plug. Remove the cover screws then pull the cover straight out with both hands to prevent damage to the grommet posts on the cover.

Before Each Use Check engine oil
After First 25 Hours or First Month Change engine oil
After 50 Hours or Every 6 Months Change engine oil1 Clean air filter2
After 100 Hours or Every 6 Months Inspect/clean spark arrestor Inspect/clean spark plug Replace fuel filter3
Inspect/adjust valve clearance3 After 300 Hours or Every Year
Replace spark plug Replace air filter
1 Change oil every month when operating under heavy load or in high temperatures.
2 Clean more often under dirty or dusty conditions. Replace air filter if it cannot be adequately cleaned.
3 Recommend service to be performed by authorized Westinghouse service dealer.

MAINTENANCE REPLACEMENT PARTS

Description Foam air filter Oil drain plug crush washer Spark arrestor Battery Spark plug Fuel filter

Part Number 5691 94007 6790 511019 97109 - F7RTC 516401

AIR FILTER MAINTENANCE
Fire hazard. Never use gasoline or other flammable solvents to clean the air filter. Use only household detergent soap to clean the air filter. The air filter must be cleaned after every 50 hours of use or six months (frequency should be increased if the generator is operated in a dusty environment).
1. Place the generator on a level surface and allow the engine to cool for several minutes.
2. Remove the engine service cover.
3. Turn the knobs on the air cleaner cover to the unlocked position. Tip the cover down to remove.

Note: The air filter element is oil soaked. Use an appropriate cleaning container.

Westinghouse Outdoor Power Equipment, LLC | 19

MAINTENANCE

NOTICE
Avoid skin contact with engine oil. Wear protective clothing and equipment. Wash all exposed skin with soap and water.

4. Remove the foam air filter from the air cleaner housing and wash it by submerging the element in a solution
of household detergent soap and warm water. Slowly
squeeze the foam to thoroughly clean.

NOTICE
DO NOT twist or tear the foam air filter element during cleaning or drying. Only apply slow but firm squeezing action.
5. Rinse the air filter element by submerging it in fresh water and applying a slow squeezing action. Allow the filter to dry thoroughly.
NOTICE
Do not pollute. Follow the guidelines of the EPA or other governmental agencies for proper disposal of hazardous materials. Consult local authorities or reclamation facility.

Check the engine oil level before each use or every 8 hours of operation.
1. Place the generator on a level surface and allow the engine to cool for several minutes.
2. Remove the oil access cover.
3. With a damp rag, clean around the oil dipstick.
4. Remove the oil dipstick and wipe the dipstick clean.

6. Dip the foam air filter in clean engine oil then squeeze out all excess oil. The engine will smoke when started if
too much oil is left in the filter.

7. Install the foam air filter in the housing and lock the air cleaner cover in place.

8. Install the engine service panel.
ENGINE OIL LEVEL CHECK

5. Insert the dipstick into the filler neck without screwing it in. Remove the dipstick and verify that the oil level is
within safe operating range.

Avoid skin contact with engine oil. Wear protective clothing and equipment. Wash all exposed skin with soap and water.

NOTICE
Always use the specified engine oil. Failure to use the specified engine oil can cause accelerated wear and/or shorten the life of the engine.
When using the generator under extreme, dirty, dusty conditions or in extremely hot weather, change the oil more frequently.
Ambient air temperature will affect engine oil performance. Change the type of engine oil used based on weather conditions.

6. If low, add recommended engine oil incrementally and recheck until the level is between the L and H marks on the dipstick. DO NOT overfill. If over the full mark on dipstick, drain the oil to reduce oil level to the full mark on dipstick.
7. Replace the oil dipstick and hand-tighten.
8. Install the oil access cover.

20 | Westinghouse Outdoor Power Equipment, LLC

MAINTENANCE

ENGINE OIL CHANGE
Accidental start-up. Remove the spark plug boot from the spark plug when working on the generator. Also remove the battery quick-connect plug from the battery. When using the generator under extreme, dirty, dusty conditions or in extremely hot weather, change the oil more frequently. Change the oil while the engine is still warm from operation.
1. Place the generator on a level surface and allow the engine to cool for several minutes.
2. Remove the engine service cover. Disconnect the spark plug wire from the spark plug and place the wire where it cannot contact the spark plug.
3. Remove the oil access cover.
4. With a damp rag, clean around the oil dipstick. Remove the dipstick and wipe clean.
5. Remove the rubber plug under the oil drain bolt and place an oil pan (or suitable container) under the drain hole.
6. Using a 10mm wrench, remove the oil drain bolt and allow the oil the to drain.

NOTICE
Do not pollute. Follow the guidelines of the EPA or other governmental agencies for proper disposal of hazardous materials. Consult local authorities or reclamation facility.
SPARK PLUG MAINTENANCE
Inspect and clean the spark plug after every 100 hours of use or six months. Replace the spark plug after 300 hours of use or every year.
NOTICE
Always use the Westinghouse OEM or compatible resistor-type spark plug. Use of a non-resistor spark plug can result in rough idling, misfire, or damage to generator components.
1. Place the generator on a level surface and allow the engine to cool.
2. Remove the engine service cover.
3. Remove the spark plug boot by firmly pulling the spark boot directly away from the engine.
4. Clean the area around the spark plug.
5. Remove the spark plug with the included spark plug socket wrench.
NOTICE
Never apply any side load or move the spark plug laterally when removing the spark plug.

6. Inspect the spark plug. Replace if electrodes are pitted, burned, or the insulator is cracked. Only use a
recommended replacement plug.

7. Install the oil drain plug and tighten securely. Install the rubber plug.
Note: A new oil drain plug crush washer is recommended at each oil change.

7. Measure the spark plug electrode gap with a wire-type feeler gauge. If necessary, correct the gap by carefully bending the side electrode.
Spark plug gap: 0.024 - 0.032 in. (0.60 - 0.80 mm)

8. Slowly pour oil into the oil fill opening until oil the level is between the L and H marks on the dipstick. Stop frequently to check the oil level. DO NOT overfill.
Maximum oil capacity: 0.63 US qt (0.60 L)

9. Replace the dipstick and hand-tighten.

10. Connect the spark plug wire and install the engine service cover.

8. Carefully install the spark plug finger tight, then tighten as additional 3/8 to 1/2 turn with the spark plug wrench.

9. Install the spark plug boot and engine service cover.

Westinghouse Outdoor Power Equipment, LLC | 21

MAINTENANCE

SPARK ARRESTOR SERVICE
Check and clean the spark arrestor after every 100 hours of use or six months. Failure to clean the spark arrestor will result in degraded engine performance.
1. Place the generator on a level surface and allow the muffler to cool before servicing the spark arrestor.
2. Remove the cover screws and the muffler cover. Use a screw driver to remove the spark arrestor.

1. Plug the charger into the battery charging port on the control panel. Plug the wall receptacle end of the battery charger into a 120 Volt AC wall outlet.
2. Unplug the battery charger from wall outlet and control panel jack after 8 hours of charging.
BATTERY REPLACEMENT
Burn hazard. The battery contains sulfuric acid (electrolyte) which is highly corrosive and poisonous. Wear protective clothing and eye protection when working near the battery. Keep children away from the battery.

Battery posts, terminals contain lead and lead compounds. Wash hands after handling.

1. Remove the battery access cover.

2. Remove the quick-connect plug and remove the battery strap. Remove the battery from the unit.

3. Carefully remove the carbon deposits from the spark arrestor screen with a wire brush. The spark arrestor must be free of breaks and tears. Replace the spark arrestor if damaged.
4. Reinstall the spark arrestor and muffler cover.
BATTERY MAINTENANCE
The battery shipped with the generator has been fully charged. A battery may lose some charge when not in use for prolonged periods of time. If the battery is unable to crank the engine, plug the included 12V charger into the battery charging port on the control panel.
Note: If the generator is not run, charge the battery overnight once a month.
The supplied battery charger is not a trickle charger and is not intended for continuous use. Do not use the battery charger for more than 8 hours (overnight) to prevent overcharging the battery.

3. Disconnect the quick-disconnect cable leads from the battery.
4. On the replacement battery, connect the white (-) quickconnect cable to the battery negative terminal. Slide the rubber boot over the connection hardware.
5. Connect the red (+) quick-connect cable to the battery positive terminal. Slide the rubber boot over the connection hardware.
6. Lift the battery strap and install the battery into the generator. Thread the battery strap under the quickconnect cables and secure it on the mounting base.
7. Connect the quick-connect plug and install the battery access cover.
NOTICE
Dispose of the used battery properly according to the guidelines established by your local or state government.

Note: Once started, the generator will charge the battery after 30­60 minutes of use. If you do not regularly
run the generator, charge the battery overnight once
a month to keep it ready for use. Charge the battery
in a dry location.

22 | Westinghouse Outdoor Power Equipment, LLC

MAINTENANCE

STORAGE
Proper storage preparation is required for trouble-free operation and generator longevity.
NOTICE
Gasoline stored for as little as 30 days can deteriorate, causing gum, varnish, and corrosive buildup in fuel lines, fuel passages and the engine. This corrosive buildup restricts the flow of fuel, which can prevent the engine from starting after a prolonged storage period. The use of fuel stabilizer significantly increases the storage life of gasoline. Full-time use of fuel stabilizer is recommended. Follow the manufacturer's instructions for use.

DRAINING THE FLOAT BOWL
1. Remove the engine service cover.
2. Locate the drain hose extending from the bottom of the carburetor float bowl.

STORAGE TIME RECOMMENDED PROCEDURE

Less than 1 month No service required.

2 to 6 months 6 months or longer

Fill with fresh gasoline and add gasoline stabilizer. Drain the carburetor float bowl. Drain the fuel tank and carburetor float bowl.

SHORT TERM STORAGE

· Allow the generator to cool a minimum of 30 minutes before storage.
· Replace all protective covers on the generator control panel.
· Wipe the generator with a moist cloth. Clean any debris from the air inlets under the control panel and muffler cooling vents.
· Store the generator in a well-ventilated, dry location away from sparks, open flames, pilot lights, heat, and other sources of ignition such as areas with a sparkproducing electric motor or where power tools are operated.
· Do not store the generator or gasoline near furnaces, water heaters, or any other appliances that produce heat or have automatic ignitions.
· With the engine and exhaust system cool and all surfaces dry, cover the generator to keep out dust. Do not use a plastic sheet as a dust cover. Non-porous materials trap moisture and promote rust and corrosion.

LONG TERM STORAGE
Even properly stabilized fuel can leave residue and cause corrosion if left long term. If storing the generator for two to six months, drain the float bowl to prevent gum and varnish buildup in the carburetor.

3. Place the loose end of the hose outside the generator into an approved gasoline container to catch the drained fuel.
4. Loosen the float bowl drain screw and allow the fuel to drain. Tighten the float bowl drain screw.
5. Route the drain hose between the air cleaner housing and the engine service cover. Install the engine service cover.
DRAINING THE FUEL TANK If storing the generator for longer than six months, drain the fuel tank to prevent fuel separation, deterioration, and deposits in the fuel system.
1. Unscrew the fuel tank cap. Remove the fuel screen filter by slightly compressing it while removing it from the tank.
2. Using a commercially available gasoline hand pump (not included), siphon the gasoline from the fuel tank into an approved gasoline container. DO NOT use an electric pump.
3. Reinstall the fuel screen filter and the fuel tank cap.
4. Start the generator and allow it to run until the generator engine stops.

5. Push the battery switch to the OFF position.

6. Disconnect the battery quick-connect plug.

7. Remove the spark plug.

Westinghouse Outdoor Power Equipment, LLC | 23

MAINTENANCE

8. Put a teaspoon of engine oil into the cylinder and pull the recoil handle until resistance is felt. At this position the piston is coming up on its compression stroke and both valves are closed. Storing the engine in this position will help prevent internal corrosion. Return the recoil handle gently.
9. Reinstall the spark plug. Leave the spark plug boot disconnected to prevent accidental starting.

8. Perform this procedure for the other valve. 9. Install the gasket, rocker arm cover, and spark plug.
MANUAL CHOKE OPERATION
If the battery is dead or disconnected, you may need to set the choke by hand for proper operation.
1. Remove the engine service cover.

10. Install the engine service cover.
VALVE CLEARANCE

2. Locate the small black choke lever on top of the carburetor.

NOTICE
Checking and adjusting valve clearance must be done when the engine is cold.

1. Remove the rocker arm cover and carefully remove the gasket. If the gasket is torn or damaged, it must be
replaced.

2. Remove the spark plug so the engine can be rotated more easily.

3. Rotate the engine to top dead center (TDC) by pulling the recoil handle slowly. Looking through the spark plug
hole, the piston should be at the top (both valves are
closed).

3. To close the choke for cold starting: Use a screwdriver to push the black lever toward the front of the generator.

4. Both the rocker arms should be loose at TDC on the compression stroke. If they are not, rotate the engine
360°.

5. Insert a feeler gauge between the rocker arm and the valve stem to measure valve clearance.

4. Start the generator. The start-up sequence should automatically open the choke. If the choke does not
open automatically, push the choke manually to open it.

Valve Clearance Torque

Intake Valve 0.0031 ­ 0.0047 in (0.08 ­ 0.12 mm)
8-12 N·m

Exhaust Valve 0.0051 ­ 0.0067 in (0.13 ­ 0.17 mm)
8-12 N·m

6. If an adjustment is necessary, hold the rocker arm pivot and loosen the pivot adjusting nut.

7. Turn the rocker arm pivot to obtain the specified clearance. Hold the rocker arm pivot and re-tighten the pivot adjusting nut to the specified torque.
Torque: 106 inch-pound (12 N·m)

NOTICE
Certain ambient temperatures and environments may require you to close the choke halfway for a successful start.

24 | Westinghouse Outdoor Power Equipment, LLC

TROUBLESHOOTING

TROUBLESHOOTING

PROBLEM Engine will not start
Engine starts, then shuts down Engine lacks power
Engine runs rough or bogs when load applied No power at AC receptacles

POSSIBLE CAUSE

CORRECTION

Battery switch in the OFF position.

Turn battery switch to the ON position.

Out of fuel.

Refuel.

Bad fuel, generator stored without treating or draining gasoline, or refueled with bad gasoline.

Drain the fuel tank. Refuel with fresh gasoline.

Dirty air filter.

Clean the air filter.

Low engine oil level stopped generator.

If low oil LED illuminated, turn battery switch to the OFF position. Add engine oil.

Spark plug wet with fuel (flooded engine).

Wait five minutes. Turn battery switch to the OFF position. Pull recoil handle rapidly
several times. If the generator does not start,
remove spark plug and dry.

Spark plug faulty, fouled, or improperly gapped. Gap or replace the spark plug. Reinstall.

Fuel filter restricted, fuel system malfunction, fuel pump failure, ignition malfunction, valves
stuck, etc.

Contact Westinghouse customer service tollfree at 1 (855) 944-3571.

Battery drained.

Use the recoil handle to start the generator. Charge the battery.

Choke partially open or closed due to weak or Manually set the choke. See Maintenance

disconnected battery.

section.

Out of fuel.

Refuel.

Incorrect engine oil level.

Check engine oil level.

Dirty air filter.

Clean the air filter.

Contaminated fuel.

Drain the fuel tank. Refuel with fresh gasoline.

Defective low oil level switch.

Contact Westinghouse customer service tollfree at 1 (855) 944-3571.

Air filter restricted.

Clean or replace air filter.

Bad fuel, generator stored without treating or draining gasoline, or refueled with bad gasoline.

Drain the fuel tank. Refuel with fresh gasoline.

Fuel filter restricted, fuel system malfunction, fuel pump failure, ignition malfunction, valves
stuck, etc.

Contact Westinghouse customer service tollfree at 1 (855) 944-3571.

Dirty air filter.

Clean the air filter.

Generator overloaded.

Unplug some devices.

Faulty power tool or appliance.

Replace or repair tool or appliance. Stop and restart the engine.

Fuel filter restricted, fuel system malfunction, fuel pump failure, ignition malfunction, valves
stuck, etc.

Contact Westinghouse customer service tollfree at 1 (855) 944-3571.

OUTPUT READY LED is OFF and OVERLOAD LED is ON.

Check AC load. Stop and restart engine.
Check the air inlet. Stop and restart the engine.

AC circuit breaker/s tripped.

Check AC loads and reset circuit breaker/s.

Faulty power tool or appliance.

Replace or repair tool or appliance. Stop and restart the engine.

Faulty generator.

Contact Westinghouse customer service tollfree at 1 (855) 944-3571.

Westinghouse Outdoor Power Equipment, LLC | 25

EXPLODED VIEWS
EXPLODED VIEWS AND PARTS LISTS
ENGINE EXPLODED VIEW
26 | Westinghouse Outdoor Power Equipment, LLC

ENGINE PARTS LIST

NO.

PART#

1

1.1

91325

1.2

241115

1.3

339915

1.4

241116

1.5

91322

2

2.1

242101

2.2

91818

2.3

242202

2.4

241804

2.5

241801

2.6

241802

2.7

246001

2.8

241806

2.9

241704

2.10 245904

2.11 91029

2.12 91359

2.13 241021

2.14 96058

2.15 240905

2.16 91007

2.17 96055

2.18 96182

3

3.1

241607

3.2

241301

3.3

241211

3.4

245503

3.5

331500

4

4.1

330202

4.2

93010

4.3

93507

4.4

97447

4.5

91333

4.6

91334

4.7

245113

4.8

91329

5

240364

6

6.1

332003

6.2

246103

6.3

241901

7

DESCRIPTION CYLINDER HEAD COVER ASSEMBLY BOLT M6X12 CYLINDER HEAD COVER POLYURETHANE SCREEN CYLINDER HEAD INNER COVER BOLT M5*12 CYLINDER HEAD ASSEMBLY ROCKING ARM ROCKING ARM TIGHTENING BOLT ASSEMBLY VALVE RETAINER ASSEMBLY TOP CAP INTAKE VALVE SPRING SEAT EXHAUST VALVE SPRING SEAT VALVE SPRING INTAKE VALVE SPRING LOWER SEAT INTAKE VALVE EXHAUST VALVE AIR INLET STUD BOLT BOLT M8X60 CYLINDER HEAD CYLINDER HEAD GASKET CYLINDER HEAD LOCATING PIN AIR EXHAUST STUD BOLT EXHAUST SEAL WASHER AIR INTAKE GASKET PISTON & PISTON RING ASSEMBLY PISTON RING ASSEMBLY PISTON PIN RING PISTON PISTON PIN CONNECTING ROD ASSEMBLY CRANKCASE ASSEMBLY CRANKCASE BEARING CRANKCASE OIL SEAL STARTING MOTOR ASSEMBLY BOLT M6*28 BOLT M6X30 OIL SENSOR BOLT M6X16 CRANKSHAFT ASSEMBLY CAMSHAFT ASSEMBLY CAMSHAFT ASSEMBLY VALVE LIFTER PUSH ROD CRANKCASE COVER ASSEMBLY

EXPLODED VIEWS

NO. 7.1 7.2 7.3 7.4 7.5 7.6 7.7 8 9 9.1 9.1.1 9.2 10 10.1 10.2 10.3 10.4 10.5 10.6 10.7 10.8 10.9 10.10 11 11.1 11.2 12 12.1 12.2 12.3 13 13.1 13.2 13.3 13.4 14
15
15.1 15.2 15.3 15.4 15.5 15.6 15.7 16 16.1

PART# 240116 245601-295 93507 91347 96041 240904 93010 599601
330501 5324 91329
91864 334501 90003 334601 500191 91400 503410 91329 339902 240904
330503 91325
330502 249914 91325
91333 339909 339903 90016 335803
244306 244304 91343 244606 91419 334302 91330
243782

DESCRIPTION CRANKCASE COVER DIPSTICK ASSEMBLY CRANKCASE OIL SEAL BOLT M8X30 CRANKCASE SEAL WASHER CRANKCASE LOCATING PIN BEARING METAL CLIP RECOIL STARTER ASSEMBLY RECOIL STARTER START PULL PLATE BOLT M6X16 IMPELLER ASSEMBLY BOLT STARTER PULLEY NUT M14 IMPELLER ROTOR BOLT M6X60 STATOR BOLT M6X16 TRIGGER CRANKCASE LOCATING PIN WIND LEAD COVER ASSEMBLY WIND LEAD COVER BOLT M6X12 UPPER WIND SHIELD ASSEMBLY UPPER WIND SHIELD CRIMPING BLOCK BOLT M6X12 IGNITION COIL ASSEMBLY BOLT M6*28 IGNITION COIL IGNITION COIL MOUNTING BRACKET NUT M6 TEMPERATURE SENSOR CENTRIFUGAL FAN HOUSING ASSEMBLY CENTRIFUGAL FAN HOUSING. CENTRIFUGAL HOOD PLUG BOLT M8*16 IMPELLER BOLT M8*1*25 CENTRIFUGAL FAN COVER BOLT M6X20 EXHAUST MUFFLER ASSEMBLY MUFFLER

Westinghouse Outdoor Power Equipment, LLC | 27

EXPLODED VIEWS

ENGINE PARTS LIST CONTINUED

NO. 16.1.1 16.2 16.3 16.4 16.5 16.6 17 18 18.1 18.2 19 19.1 19.1.1 19.2 20 20.1 20.2 20.3 20.4 20.5 20.6 20.7 20.8 20.9 20.10 21 21.1 21.1.1 21.2 21.3 21.4 22 23 24 25 26 27 28 29

PART# 6790 94216 94206 90011 91330 500057 240511
91330 249917
332901 5691 95918
332301 92219 90016 249934 332801 249925 92055 249949 249950 92240
337001 5697 249919 95602 94407 97109 96200 94226 96051 94007 94035 91831 91816

DESCRIPTION SPARK ARRESTER FLAT WASHER SPRING WASHER NUT M8 BOLT M6X20 MUFFLER COVER SHIELD BRACKET ASSEMBLY BOLT M6X20 BRACKET AIR FILTER ASSEMBLY AIR FILTER FILTER CONNECTING PIPE CARBURETOR ASSEMBLY CARBURETOR CONNECTION BLOCK SCREW M4*20 NUT M6 WATERPROOF COVER CARBURETOR ASSEMBLY STEPPER MOTOR BRACKET SCREW M4X25 STEPPER MOTOR STEPPER MOTOR CROSSING SCREW M4X6 RESONANT CAVITY ASSEMBLY RESONANT CAVITY FOAM FILTER PLUG BREATHER TUBE FUEL LINE CLAMP SPARK PLUG CYLINDER HEAD COVER SEAL WASHER STEEL WASHER CARBURETOR GASKET OIL DRAIN BOLT WASHER OIL DRAIN BOLT WASHER OIL DRAIN SOLENOID OIL DRAIN BOLT

28 | Westinghouse Outdoor Power Equipment, LLC

GENERATOR EXPLODED VIEW

EXPLODED VIEWS

Westinghouse Outdoor Power Equipment, LLC | 29

EXPLODED VIEWS

GENERATOR PARTS LIST

NO.
1
2 3 3.1 3.2 3.3 3.4 4 4.1 4.2 4.3
4.4
4.5 4.6 4.7 5 5.1 5.2 5.3 5.4 5.5 5.6 5.7 5.8 5.9 6 6.1 6.2 6.3 6.4 6.5 6.6 6.7 6.8 6.9 6.10 7 7.1
7.2
7.3 7.3.1 7.3.2 7.3.3 7.3.4

PART#
110022 530064

DESCRIPTION ENGINE ASSEMBLY

599601

METAL CLIP

INVETER MODULE ASSEMBLY

91325

BOLT M6X12

503147

INVETER

503013

BRACKET

91322

BOLT M5×12

LEFT FRAME ASSEMBLY

503005-221 LEFT FRAME

91345

BOLT M8X20

500060

LOCK CLIP M6

503039221A

LEFT PANEL

92097

HEX FLANGE SCREW M6X20

500007

FUEL TANK ISOLATION PAD A

92079

STOP BOLT M6X16

BRACKET ASSEMBLY

503001

BRACKET

503002

BRACKET

503003

BRACKET

503004

ISOLATION PAD

90044

NUT M8

91325

BOLT M6X12

500044

SHORT WIRE

91348

BOLT M8X35

94003

TOOTH WASHER

BRACKET ASSEMBLY

91325

BOLT M6X12

503017

BRACKET

503018L

FUEL LINE CLAMP

503019L

FUEL LINE CLAMP

503020L

FUEL LINE CLAMP

503044

CLIP

503062

FUEL SWITCH

503034

FUEL LINE CLAMP

516401

FUEL FILTER

94408

FUEL LINE CLAMP

CONTROL PANEL ASSEMBLY

503016

PANEL REAR COVER

92078

CROSS RECESSED PAN HEAD BOLT M6X16

503061

CONTROL PANEL ASSEMBLY

6500

ROCKER SWITCH

9022

ONE PUSH BUTTON SWITCH

9032

ECO SWITCH

9079

WATERPROOF CAP

30 | Westinghouse Outdoor Power Equipment, LLC

NO. 7.3.5 7.3.6 7.3.7 7.3.8 7.3.9 7.3.10 7.3.11 7.3.12 7.3.13 7.3.14 7.3.15 7.3.16 7.3.17 7.3.18 7.3.19 7.3.20 7.3.21 7.3.22 7.3.23 7.3.24 7.3.25 7.3.26 7.4 7.5 7.6 7.7 7.8 8 8.1 8.2 8.3 8.4
8.5
9 9.1 9.2 9.3 9.4
9.5
9.6 9.7 9.8 9.9 9.11 9.12

PART# 6441-31

DESCRIPTION 31A THERMAL PROTECTOR

6404

WATERPROOF CAP

9025

CHARGING SOCKET

6441-30

30A THERMAL PROTECTOR

6404

WATERPROOF CAP

9089

START INDICATOR

6441-20

20A THERMAL PROTECTOR

6404

WATERPROOF CAP

97537

IGNITOR

503310

KNOB PLUG

9141

USB

503108

USB DUST COVER

9021

VOLTAGE RESET BUTTON

9110

LED

9193

PARRALLEL PORTS

9122

WATERPROOF CAP

6032

5-20R RECEPTACLE

9194

DUST COVER

6015

RV SOKET

6849

DUST COVER

9132

GROUNDING BOLT

9016

PANEL BODY

91825

BOLT M5X12

503024

KNOB

500068

HANDLE BAFFLE PLUG

92032

SCREW M4*16

94325

FLAT WASHER

TOP COVER ASSEMBLY

500068

HANDLE BAFFLE PLUG

503025

PLUG

503029

OIL CHANNEL

503038-221 T0P COVER

92078

CROSS RECESSED PAN HEAD BOLT M6X16

FUEL TANK ASSEMBLY

503068L FUEL TANK ASSEMBLY

500008

FUEL TANK ISOLATION PAD B

91322

BOLT M5×12

500252

SEALING RING

95127

CARBON CANISTER AND FUEL TANK CONNECTING PIPE

500247

GASOLINE SENSOR

94405

FUEL LINE CLAMP

94403

FUEL LINE CLAMP

96801

FUEL TANK WASHER

500244

PRESSURE PLATE

500324

SEALING WASHER

GENERATOR PARTS LIST CONTINUED

NO. 10 10.1 10.2 10.3 10.4 10.5 10.6 10.7 10.8 10.9 10.10 10.11 10.12 10.13 10.14 10.15 10.16 11
11.1
11.2 11.3 11.4 11.5 11.6 11.7 11.8 12 12.1 12.2 13 13.1 13.2 13.3
13.4
14 14.1 14.2 15 15.1 15.2 15.3 15.4 15.5 15.6
15.7

PART#

DESCRIPTION

100200006 BASEBOARD ASSEMBLY

90027

SQUARE NUT

91325

BOLT M6X12

503048

DC VOLTAGE REGULATOR

500060

LOCK CLIP M6

503026

ISOLATION PAD

503023

AXLE

503031

WHEEL

503032

WHEEL COVER

503033

PULL ROD HOLDER

503035

PULL ROD

503045

BOTTOM PLATE

94022

STEEL WASHER

500321

AXLE WILD CARD

503053

LIMIT BLOCK

503052

BASE OIL COVER

91334

BOLT M6X30

RIGHT FRAME ASSEMBLY

503021221A

RIGHT FRAME

91345

BOLT M8X20

503022-221 OBSERVATION COVER

500060

LOCK CLIP M6

503067

BLIND RIVET

503036-052 HANDLE DECORATIVE BOARD

94249

FLAT WASHER

92097

HEX FLANGE SCREW M6X20

RECOIL HANDLE ASSEMBLY

500017-231 HANDLE COVER

500018

HANDLE

MUFFLER BAFFLE ASSEMBLY

503027

MUFFLER BAFFLE

500108

MUFFLER EXHAUST SEALING STRIP

503040

COVER

92078

CROSS RECESSED PAN HEAD BOLT M6X16

BATTERY ASSEMBLY

503165

BATTERY CABLE

599606

BATTERY TIE

CARBON CANISTER ASSEMBLY

91325

BOLT M6X12

94405

FUEL LINE CLAMP

94403

FUEL LINE CLAMP

91334

BOLT M6X30

543301L

CARBON CANISTER ASSEMBLY

503043

BRACKET

95016

CARBON CANISTER AND AIR FILTER CONNECTING PIPE

EXPLODED VIEWS

NO.

PART#

16

16.1

91325

16.2

503006

16.3

503008

16.4

503009

16.5

503042

16.6

91330

17

17.1

91325

17.2

503007

17.3

503008

17.4

503009

17.5

503011

17.6

91335

17.7

503047

17.8

90010

17.9

91330

18

511019

19

503028

20

518801

21

503388

22

503082

23

99011

24

500942

25

99629

26

511043

27

99506

DESCRIPTION BRACKET ASSEMBLY BOLT M6X12 UPRIGHT BRACKET HANDLE BRACKET BOLT M6X20 BRACKET ASSEMBLY BOLT M6X12 UPRIGHT BRACKET HANDLE BRACKET BOLT M6X35 CONTROL MODULE NUT M6 BOLT M6X20 BATTERY FUEL TANK CAP FILTER WIRING HARNESS BELLOW SPARK PLUG WRENCH FUNNEL OIL BOTTLE CHARGER SCREWDRIVER

Westinghouse Outdoor Power Equipment, LLC | 31

SCHEMATICS
SCHEMATICS
32 | Westinghouse Outdoor Power Equipment, LLC



References

Adobe PDF Library 15.0 Adobe InDesign 16.3 (Windows)