Richauto A11E Manual Pdf - How to Set Parameters on RichAuto A11 Controller?
4' x 8' CNC Router at Grizzly.com
SECTION 9: PARTS We do our best to stock replacement parts when possible, but we cannot guarantee that all parts shown are available for purchase. Call (800) 523-4777 or visit www.grizzly.com/parts to check for availability. Frame & Bed 18 17 7 6 3 27 10 2 1 22 21 26 26 16 13 14 15 11 12 94 15-2 20 5 15-1 15-3 8 11 19 19-1 19-2 24 25 25-3 25-4 23 25-1 25-2 25-5 REF PART # 1 P0895001 2 P0895002 3 P0895003 4 P0895004 5 P0895005 6 P0895006 7 P0895007 8 P0895008 9 P0895009 10 P0895010 11 P0895011 12 P0895012 13 P0895013 14 P0895014 15 P0895015 15-1 P0895015-1 15-2 P0895015-2 15-3 P0895015-3 16 P0895016 DESCRIPTION CORNER COVER (LEFT) PANEL (FRONT) BODY LINEAR GUIDE 25MM RACK SIDE PANEL (LEFT, FRONT) SIDE PANEL (LEFT, REAR) CAP SCREW M6-1 X 30 CAP SCREW M5-.8 X 25 Z-AXIS SENSOR LIMIT BLOCK AIR DISTRIBUTION PIPE AIR VALVE PANEL (REAR) VACUUM PUMP VACUUM PUMP FILTER ASSEMBLY PLEXIGLASS COVER W/RUBBER SEAL VACUUM PUMP FILTER VACUUM TABLE Model G0895 (Mfd. Since 07/20) REF 17 18 19 19-1 19-2 20 21 22 23 24 25 25-1 25-2 25-3 25-4 25-5 26 27 PART # P0895017 P0895018 P0895019 P0895019-1 P0895019-2 P0895020 P0895021 P0895022 P0895023 P0895024 P0895025 P0895025-1 P0895025-2 P0895025-3 P0895025-4 P0895025-5 P0895026 P0895027 DESCRIPTION CABLE SUPPORT CABLE CARRIER LEVELING FOOT HEX NUT M20-2.5 FLAT WASHER 20MM DUST COVER VACUUM HOSE 2" CORNER COVER (RIGHT) SIDE PANEL (RIGHT, FRONT) SIDE PANEL (RIGHT, REAR) T-SLOT CLAMP T-SLOT CLAMP PLATE HEX BOLT M8-1.25 X 50 WING NUT M8-1.25 FLAT WASHER 8MM T-BOLT M8-1.25 X 80 HOSE CLAMP 2" GASKET TUBE BUY PARTS ONLINE AT GRIZZLY.COM! Scan QR code to visit our Parts Store. -51- Gantry & Spindle 148 140 135 134 148 145 144 150 152 133 131 132 146 149 139 125 130 129 128 126 124 123 142-4 142-3 141 104 103 102 101 142 138 153 154 156 155 157 113 112 107 137 106 105 143 111 136 110 109 158 115 108 114 147 139 139 122 120 118 119 116 117 -52- BUY PARTS ONLINE AT GRIZZLY.COM! Scan QR code to visit our Parts Store. Model G0895 (Mfd. Since 07/20) Gantry & Spindle Parts List REF PART # 101 P0895101 102 P0895102 103 P0895103 104 P0895104 105 P0895105 106 P0895106 107 P0895107 108 P0895108 109 P0895109 110 P0895110 111 P0895111 112 P0895112 113 P0895113 114 P0895114 115 P0895115 116 P0895116 117 P0895117 118 P0895118 119 P0895119 120 P0895120 122 P0895122 123 P0895123 124 P0895124 125 P0895125 126 P0895126 128 P0895128 129 P0895129 130 P0895130 131 P0895131 DESCRIPTION SPINDLE MOTOR 6HP 3-PH 220V MOTOR MOUNT CAP SCREW M5-.8 X 20 Z-AXIS MOUNT SLIDE BRACKET 25MM CAP SCREW M5-.8 X 25 LINEAR GUIDE 25MM BALL SCREW 25MM BEARING SEAT BALL SCREW SEAT Z-AXIS MOTOR MOUNT Z-AXIS SERVO MOTOR SGM7G-09AFC6C SPINDLE COVER (LOWER) SPINDLE COVER (UPPER) CAP SCREW M5-.8 X 20 X-AXIS MOUNT SLIDE BRACKET 25MM DRIVE BOARD BRACKET GEAR X-AXIS SERVO MOTOR MOUNTING BOARD X-AXIS SERVO MOTOR SGM7G-09AFC61 Y-AXIS COVER (UPPER, RIGHT) Y-AXIS COVER (LOWER, RIGHT) Y-AXIS SERVO MOTOR SGM7G-09AFC61 TIMING BELT 5M 550 GEAR BOX & PULLEY GANTRY SUPPORT (RIGHT) SLIDE BRACKET 25MM CAP SCREW M5-.8 X 20 REF 132 133 134 135 136 137 138 139 140 141 142 142-3 142-4 143 144 145 146 147 148 149 150 152 153 154 155 156 157 158 PART # P0895132 P0895133 P0895134 P0895135 P0895136 P0895137 P0895138 P0895139 P0895140 P0895141 P0895142 P0895142-3 P0895142-4 P0895143 P0895144 P0895145 P0895146 P0895147 P0895148 P0895149 P0895150 P0895152 P0895153 P0895154 P0895155 P0895156 P0895157 P0895158 DESCRIPTION LINEAR GUIDE 25MM GANTRY RACK CAP SCREW M6-1 X 25 CAP SCREW M8-1.25 X 35 CAP SCREW M6-1 X 45 CAP SCREW M6-1 X 30 LIMIT SWITCH TL-Q5MC1-Z LUBRICATION PUMP CONDUIT DUST HOOD ASSEMBLY CAP SCREW M5-.8 X 30 HEX NUT M5-.8 COUPLER CABLE CARRIER CABLE SUPPORT CAP SCREW M5-.8 X 20 CAP SCREW M8-1.25 X 30 LIMIT BLOCK CAP SCREW M12-1.75 X 60 Y-AXIS COVERS 2-PC SET GANTRY SUPPORT (LEFT) SPINDLE NUT ER32 COLLET 6MM ER32 COLLET 1/2" ER32 COLLET WRENCH ER32 WRENCH 30 X 32 OPEN ENDS Z-AXIS SHAFT COLLAR Model G0895 (Mfd. Since 07/20) BUY PARTS ONLINE AT GRIZZLY.COM! Scan QR code to visit our Parts Store. -53- Electrical Cabinet Cabinet Front 207 208 209 210V2 211V2 212V2 213V2 218 218 212V2 213V2 214 215 204 216 Cabinet Rear 201 217 205 206 204 202 202 202 202 203 203 203 203 REF PART # DESCRIPTION 201 P0895201 DSP CONTROLLER RICHAUTO A11E 202 P0895202 SERVO MOTOR YASKAWA SGD7S-7R6A00A 203 P0895203 BRAKE RESISTANCE 200W 204 P0895204 FAN SUNON 2122HSL 205 P0895205 ON SWITCH YIJIA YJ136-LA38 206 P0895206 E-STOP SWITCH YIJIA YJ136-LA38 207 P0895207 DSP CONTROLLER RICHAUTO 208 P0895208 VFD DELTA MS300 VFD25AMS23ANSAA 209 P0895209 POWER CONVERTER LRS01-150-24D REF PART # DESCRIPTION 210V2 P0895210V2 CIRCUIT BREAKER 32A IC65N V2.01.20 211V2 P0895211V2 CONTACTOR LC1R2510 V2.01.20 212V2 P0895212V2 TERMINAL BAR 4P V2.01.20 213V2 P0895213V2 TERMINAL BAR 6P V2.01.20 214 P0895214 RELAY OMRON MY2N-GS 24VDC 215 P0895215 POWER TERMINAL 6P 216 P0895216 CONTROLLER CABLE 50-PIN 217 P0895217 CONTROLLER CABLE USB 218 P0895218 FUSE 32A 690V RT18-32X -54- BUY PARTS ONLINE AT GRIZZLY.COM! Scan QR code to visit our Parts Store. Model G0895 (Mfd. Since 07/20) Labels & Cosmetics 305 301V2 303 Specifications Motor: 6 HP, 220V, 1-Ph, 60 Hz, 16A Full-Load Current Rating: 20A Collet Type: ER32 Cutting Area: 51" x 98-1/2" x 7" Table Size: 53-3/4" x 120-1/4" Cutting Accuracy: +/-0.005" Spindle Speed: 018,000 RPM X and Y Travel Speeds: 1500 IPM Z Travel Speeds: 400 IPM Weight: 2315 lbs. Date S/N Mfd. for Grizzly in China 306 MODEL G0895 4' x 8' CNC ROUTER WARNING! To reduce the risk of serious injury when using this machine: 1. Read and understand owner's manual 11. Only use clamps or vacuum pump to before operating. secure workpiece for operations. 2. Only properly trained personnel should 12. Use proper dust collection to operate CNC machine. accomodate full range of movement. 3. Always wear approved eye and hearing 13. NEVER reach over or across machine protection, and a respirator. when in operation. 4. Avoid entanglement with moving 14. Stand out of path of all moving parts. parts--tie back long hair, roll up long 15. Keep all guards and covers in place sleeves, and do not wear loose during operations. clothing, gloves, or jewelry. 16. Avoid damage to machine and material 5. Always use proper feeds and speeds by taking multiple light cuts. for operation and workpiece. 17. Never attempt to slow or stop spindle 6. Verify software-generated code to avoid with hands or tools. crashing spindle. 18. In an emergency use EMERGENCY STOP 7. Properly ground machine--connect to button. permanently grounded metal wiring 19. Never leave machine running unattended. system or an equipment-grounding 20. Never operate machine while intoxicated, conductor. distracted, or tired. 8. Disconnect power before changing 21. Do not expose to rain/dampness. cutters, and/or adjusting/servicing 22. Prevent unauthorized use by children or spindle. untrained users. 9. Before starting, ensure spindle nut is tight on collet. 10. Always remove wrenches and adjustment tools before starting. WARNING! INJURY HAZARD! To reduce risk of shortand long-term injury, wear safety glasses, hearing protection, and a respirator when using this machine. 320 G0895 307 WARNING! To reduce risk of death or serious injury, read manual BEFORE using machine. To get a new manual, call (800) 523-4777 or go to www.grizzly.com. INJURY/SHOCK HAZARD! Disconnect power before adjustments, maintenance, or service. 304 312 WARNING! ENTANGLEMENT HAZARD! Tie back long hair, roll up long sleeves, and remove loose clothing, jewelry, or gloves to prevent getting caught in moving parts. · Lubricant: Use Grizzly T27914 Way Oil or ISO 68 equivalent. · Lubricate system every 8 hours of operation, or weekly. · Oil reservoir max capacity is 1 quart. · To operate pump, press up & down arrows. · Clean/replace suction filter annually or sooner, if needed. grizzly.com Use Existing Label 321 Oil Reservoir on Back of Gantry Use Existing Label 309 WARNING! CUTTING HAZARD! Keep fingers and other body parts away from cutting path. G8589 11.03" x 5.32" 311 310 302 G0895 INJURY HAZARD! Do not open door while machine is connected to power or spindle is in motion. grizzly.com308 313 315 316 317 318 CAUTION! HOT SURFACE! DO NOT TOUCH! 314 319 Use Existing Labels 322 SHOCK HAZARD! Diconnect power before opening junction box or working on wiring. Vacuum Valves on Back of Frame Vacuum Pump Model G0895 (Mfd. Since 07/20) BUY PARTS ONLINE AT GRIZZLY.COM! Scan QR code to visit our Parts Store. -55- Labels & Cosmetics Parts List REF PART # DESCRIPTION 301V2 P0895301V2 MACHINE ID LABEL V2.01.20 302 P0895302 MODEL NUMBER LABEL (SMALL) 303 P0895303 EYE/EAR/LUNG LABEL 304 P0895304 ENTANGLEMENT LABEL 305 P0895305 READ MANUAL LABEL 306 P0895306 ELECTRICITY LABEL 307 P0895307 DISCONNECT POWER LABEL 308 P0895308 GRIZZLY.COM LABEL (SMALL) 309 P0895309 CUTTING HAZARD LABEL 310 P0895310 DO NOT OPEN LABEL 311 P0895311 GRIZZLY NAMEPLATE (LARGE) REF PART # 312 P0895312 313 P0895313 314 P0895314 315 P0895315 316 P0895316 317 P0895317 318 P0895318 319 P0895319 320 P0895320 321 P0895321 322 P0895322 DESCRIPTION OIL RESERVOIR LABEL HOT SURFACE LABEL VACUUM ZONE LABEL (TOP, LEFT) VACUUM ZONE LABEL (TOP, CENTER) VACUUM ZONE LABEL (TOP, RIGHT) VACUUM ZONE LABEL (BOTTOM, LEFT) VACUUM ZONE LABEL (BOTTOM, CENTER) VACUUM ZONE LABEL (BOTTOM, RIGHT) MODEL NUMBER LABEL (LARGE) GRIZZLY.COM LABEL (LARGE) DO NOT OPEN JUNCTION BOX LABEL Safety labels help reduce the risk of serious injury caused by machine hazards. If any label comes off or becomes unreadable, the owner of this machine MUST replace it in the original location before resuming operations. For replacements, contact (800) 523-4777 or www.grizzly.com. -56- BUY PARTS ONLINE AT GRIZZLY.COM! Scan QR code to visit our Parts Store. Model G0895 (Mfd. Since 07/20)Adobe InDesign 14.0 (Macintosh) Adobe PDF Library 15.0