User Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 3730683 |
| Application ID | FhJfLkv06AZG6dttB4JWjA== |
| Document Description | User Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 112.21kB (1402661 bits) |
| Date Submitted | 2018-01-26 00:00:00 |
| Date Available | 2018-01-26 00:00:00 |
| Creation Date | 2017-12-08 17:55:53 |
| Producing Software | Adobe PDF library 10.01 |
| Document Lastmod | 2018-01-08 11:08:24 |
| Document Title | 12.1 BS210RE (BTH-101-1) 英文说明书（未转曲） |
| Document Creator | Adobe Illustrator CS6 (Windows) |
Structure Sketch Note 1: Check the charging device is suit to the headset or not. Note 2: Use only the supplied charger to charge the headset, if use other device may violate the validation or the maintenance article of this product and may cause danger. Note 3: Do not attempt to force open the built-in battery as this could damage the headset. BTH-101-1 Magnetic Bluetooth Stereo Headset User Manual (1)Drivers (2)Volume Key- (V-) (3)Multifunction Button (MFB) (7)Indicator Light of Charging (4)Volume Key+ (V+) (8)Charging Pin (5)Type C Charging Socket (6)Micphone/Indicator Light of Power on/off The Headset Status Bluetooth headset should be used with the compatible devices which support Bluetooth wireless technology. This allows you to make two calls and enjoy the music streaming at any time freely. Please read this user manual carefully before using the headset, and also read your device’s user manual regarding the Bluetooth function, and pay attention to those important safety and maintenance information. Please keep the headset away from children. Status No. Status Pairing Mode Not Connected Standby Mode Bluetooth Specification V4.2 Bluetooth Profiles Supported HSP, HFP, A2DP, AVRCP Audio Decoding Profiles Supported APTX, APTX-LL, SBC, AAC Noise Cancellation Version CVC 6.0 Transmission Power Class 2 Operation Range Up to 10 Meters Frequency Range 2.402-2.480GHz Battery Built-in Rechargeable 3.7V /60mAH Lithium Battery Charging Voltage DC 5V±0.25V Charging Time About 2 hours Music Playing Time* Up to 3 hours Talk Time * Up to 3.5 hours Standby Time * Up to 108 hours Driver φ10MM Sensitivity of Driver 109±3dB/1kHz Impedance of Driver 16Ω±15% Frequency Range of Driver 20Hz~20kHz Dimensions of Earbuds L29×W16×H16 Dimensions of Control and L54.5×W11×H7 Battery Box(mm): Dimensions of PCB Box(mm): L40.6×W11.5×H8.9 Weight About 24 g *The time mentioned above may vary due to user's operation mode and device settings. When the headset is in the mode of being searched, the indicator light flashses red and blue alternately and the speaker prompts “Bluetooth Pairing”. When the headset is not connected with the device, blue light will flash once each 2 seconds. When the headset is connected with the device but no any other operations, the blue light will flash once each 5 seconds. Call Mode When in a call, the indicator light flashes blue once each 10 seconds. Charging Mode The indicator light turns red while being charged, and will turn off automatically after being fully charged. Specifications Headset Performance When the battery's voltage is below than 3.3V, the Low Voltage State indicator light flashes red, and the speaker prompts “Battery Level Low” every minute. If the pairing cannot be completed within 5 minutes after the Pairing Mode has been activated, the headset will power off automatically, the speaker prompts "Bluetooth Power off Pairing Failed" - "DiDi" - "Power off". Automatically When the headset is disconnected in Standby Mode, it will power off automatically after 5 minutes and the speaker prompts "DiDi" - "Power off". When the headset is in standby mode and it is moved out the operation range of the phone, the headset will be disconnected, the blue light will flash once each 5 seconds and the speaker prompts "DuDu" (The speaker Disconnected Mode prompts "DuDu" each 15 seconds). When the headset is disconnected by phone, the blue light will flash once each 2 seconds and the speaker prompts "Bluetooth Disconnected". Pairing Failed Mode "Bluetooth Pairing Failed". When the headset pairing failed, the speaker prompts Note: The two Phones mentioned follows will be called Phone A and B. Charging Your Headset 1. Prior to using the headset for the first time or no use for a long time, please fully charge the battery. 2. Approximately 2 hours are required to fully charge the headset. 3. The indicator light turns red while being charged, and will turn off automatically after being fully charged. 4. When the headset is running out of battery, the indicator light will flash red (the headset will switch off automatically when the battery is drained). Please charge the headset as above steps in time to prolong the battery's useful life (Charging indication will be delayed for a few minutes if the headset has not been used for a long time or the battery is drained). Note 4: A fully charged headset will loose its power automatically if left unused. It is recommended to charge the headset each three months. Note 5: Do not leave the headset in a too hot or too cold condition (best between -10℃ and 50℃) which may affect the headset's operations although it is fully charged. Note 6: Do not dispose of the headset into fire or water. Turning on Headset In OFF MODE, press and hold MFB for 2 seconds, until you hear “Di Di Di Power on”, the indicator light turns blue for 1 second, then the headset will enter into ON MODE. The headset will be connected automatically(when the headset isn’t connect to any other Bluetooth devices and the pairing list is empty, the headset will enter into pairing mode automatically). Answering a Call When a call is coming, you can answer it with the ways as follows: Method 1: Press MFB once. Method 2: Answer the call with your phone. Ending a Call You can end the call you are answering with the ways as follows: Method 1: Method 2: Press MFB once. End the call with your phone. Rejecting a Call Turning off Headset In ON MODE (except call state), press and hold MFB for 3 seconds, until you hear “Di Di Power off”, the indicator light turns red for 1 second, then the headset will enter into OFF MODE. Note: Headset isn’t connected with any devices within 5 minutes, it will automatically turn off. Press and hold MFB for 2 seconds to reject the call. Calling Transferring During a call, press and hold “V-“ for 2 seconds and you will hear “Du” prompt voice and can shift the call between cellphone and headset. Two-call Handling Pairing Your Headset with a Bluetooth Phone 1. Ensure the headset is off, and the distance between your headset and phone is within 1 meter to activate the Bluetooth function on the phone. 2. Press and hold MFB for 2 seconds until the indicator light flashes red and blue alternately and could hear “Bluetooth Pairing” as PAIRING MODE. 3. Search Bluetooth devices (see the user guide of your phone for instructions). 4. Select headset “RATEL Ear BT” from the devices list of the phone. 5. Select headset “RATEL Ear BT”(If the version of the phone is or under 2.0, you should input pairing code “0000”, and confirm). Later you could hear “Bluetooth Paired” and then “Bluetooth Connected”. (If the pairing cannot be completed within 5 minutes after the PAIRING MODE has been activated, the headset will power off. Please repeat above steps to do the pairing again). 6. Ensure there is no obstruction between your headset and phone and within effective distance, you can use the headset freely. 7. Under the circumstance of power off, once you turn on the headset again, it will connect the paired phone automatically within operation range. (See the user guide of your phone for instructions.) When you are answering a call, there is another call coming: 1. Press and hold MFB for 2 seconds to end the current call and answer another one. 2. Shortly press MFB once to answer another call and hold on the current one. 3. After the above operation “2” settled, shortly press MFB to transfer one call to another. 4. After the above operation “2” settled, press and hold MFB for 2 seconds to end the current calling and shortly press MFB to end another one. Note: All the above operations have to respect the precondition that Phone supports Bluetooth hands free profile V1.5 and Phones are running under call holding function(Network service) from telecom. Mute During a call, press and hold “V+” for 3 seconds, the headset will enter into MUTE MODE. In MUTE MODE, the speaker will sound “Du” twice every 10 seconds, you could cancel the MUTE MODE if press and hold “V+” for 3 seconds again. Adjusting the Volume Two-link Function: In call or music playing state, shortly press “V+ ”or “V-” once to adjust the volume. When the volume up to maximum or minimum, you could hear “Di” voice prompt. This function means “RATEL Ear BT” Bluetooth headset is connected with 2 Phones of Bluetooth function at the same time. When the Phone A & Phone B are neither paired, the two link operation is as below: Forward/Backward 1). Pairing Phone A: In OFF Mode, press and hold MFB until indicator light flashes red and blue alternately, use phone A to search the Bluetooth device “RATEL Ear BT”, enter pairing code “0000” and confirm, pair the headset with phone A, and the headset will enter into standby mode. Press and hold “V+” or “V-” for 2 seconds to forward the next song or backward the previous song. Note: Due to technology of different phones, it’s not sure for all phones can go back to the previous song, it may be back to the beginning. Music Pause /Playing Shortly press MFB to PLAY music(paired and standby condition), press MFB again to PAUSE music. 2). Turn off the Bluetooth function or switch off power in Phone A, the headset will go back to no connected status. 3). Pairing Phone B: In OFF Mode, press and hold MFB until indicator light flashes red and blue alternately, use phone B to search the Bluetooth device “RATEL Ear BT”, enter pairing code “0000” and confirm, pair the headset with phone B, and the headset will enter into standby mode. Delete Pairing Record on the Headset In ON and not connected mode, press and hold “V+” for 2 seconds until the red and blue light flashes twice at the same time, you will hear “Du” prompt voice twice, then the pairing record on the headset will be deleted. When all the pairing records are deleted, after the headset turn on again, it couldn’t connect automatically and enter into pairing mode directly. The headset will be turned off automatically if not connect with any Bluetooth devices in 5 minutes. The headset will beep when operates successfully but this may be too low to hear. The above operations may vary due to different devices. Disconnecting To disconnect the paired headset from your phone, please turn off the headset or disconnect the headset from the Bluetooth menu of your phone. When disconnecting, you could hear “Bluetooth disconnected”. 4). Connecting the Phone A&B at the same time: Voice Function In PAIRED MODE, press MFB twice to activate voice function (ISO system should wait for 8-10 seconds to activate voice function after music pause). Ensure your phone supports voice function, and you have recorded the voice tag into your phone. See the user guide of your phone for instructions. Headset Resetting In any state, as long as the headset is charging, it will be reset. Method 1: Method 2: Activate the Bluetooth function or switch on the power of Phone A, search the Bluetooth device “RATEL Ear BT” with Phone A, and connect it with this phone, here 2 Phones are connected with the headset. Activate the Bluetooth function of phone A/B and re-turn on the on mode headset. The headset will automatically connect with (A/B ) phone. If need to connect the 2nd phone, you should use manual operation on phone. of all functions on every Bluetooth enabled device. Connected phones with APTX/APTX-LL function, phones will show connected APTX/APTX-LL Two-link Function version under 2.1, but there is no need if your phone is or above version 2.1. Two-call Handling after 2-Link: When you are answering a calling from phone A, there is another calling from phone B: 1. Press and hold MFB for 2 seconds to end the current call and answer another one. 2. Shortly press MFB once to answer another call and hold on the current one. 3. After the above operation “2” settled, shortly press MFB to transfer one call to another. 4. After the above operation “2” settled, press and hold MFB for 2 seconds to end the current calling and shortly press MFB to end another one. Note: The two Phones mentioned follows will be called Phone A and B. This function is once paired the headset will connect with phone automatically and no need connect any more(Make sure your phone Bluetooth function is activated and in the operation range with phone). Type C charging cable Checking whether the In OFF Mode, after activating the headset, it will connect the phones according to the pairing list in 5 minutes. If beyond 5 minutes and not connected, the headset will Power off. Without indcator does’t output voltage or Type C charging cable light in charging DC power supply does’t is plugged or DC power output power switch is on Note 1: For the difference of Phones, it doesn’t guarantee the compatibility Note 2: You should enter pairing code “0000” if your phone Bluetooth APTX/APTX-LL Function Automatic Re-connecting Maintenance Do not use abrasive cleaning solvents to clean the headset. Do not allow the headset to touch with any sharp objects as this will cause scratching and damage. Please keep headset away from high-temperature, humidity and dust. Additional Statements The headset is compliant with the specified Bluetooth version. It does not guarantee compatibility of all functions on every Bluetooth enabled device. Please check your device’s user manual for compatibility and functionality. Since there is maybe a defect of compatibility for different devices and especially for the third party players , it may cause the malfunction of music play/pause. ISO System should wait In music playing mode for 8-10 seconds to act Can not activate or music pausing mode ivate voice function after voice function within 10 seconds music pause Please check if have Clean the dirty and sweat on charging pin Can not be charged dirty and sweat on by charging pin charging pin FCC Warning This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE : Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : No XMP Toolkit : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04 Format : application/pdf Title : 12.1 BS210RE (BTH-101-1) 英文说明书（未转曲） Metadata Date : 2018:01:08 11:08:24+08:00 Modify Date : 2018:01:08 11:08:24+08:00 Create Date : 2017:12:08 17:55:53+09:00 Creator Tool : Adobe Illustrator CS6 (Windows) Thumbnail Width : 176 Thumbnail Height : 256 Thumbnail Format : JPEG Thumbnail Image : (Binary data 22233 bytes, use -b option to extract) Instance ID : uuid:c08b80d2-ce3f-45cb-9809-01104d6e31c8 Document ID : xmp.did:B7D61465B6DBE711A404AE6349B49429 Original Document ID : uuid:5D20892493BFDB11914A8590D31508C8 Rendition Class : proof:pdf Derived From Instance ID : uuid:e95209ec-277c-414d-91fc-62ba3d986241 Derived From Document ID : xmp.did:2756E0AFDBD3E711B074E3A1A3F92772 Derived From Original Document ID: uuid:5D20892493BFDB11914A8590D31508C8 Derived From Rendition Class : proof:pdf History Action : saved, saved History Instance ID : xmp.iid:BDAD87ABC2C1E111BED484D3A664D8C3, xmp.iid:B7D61465B6DBE711A404AE6349B49429 History When : 2012:06:29 16:16:04+08:00, 2017:12:08 17:55:43+08:00 History Software Agent : Adobe Illustrator CS5, Adobe Illustrator CS6 (Windows) History Changed : /, / Startup Profile : Print Has Visible Overprint : False Has Visible Transparency : False N Pages : 1 Max Page Size W : 29.699996 Max Page Size H : 21.000010 Max Page Size Unit : Centimeters Font Name : ArialNarrow, ArialMT, Arial-BoldMT, SimSun, AdobeSongStd-Light Font Family : Arial, Arial, Arial, 宋体, Adobe 宋体 Std Font Face : Narrow, Regular, Bold, Regular, L Font Type : Open Type, Open Type, Open Type, TrueType, Open Type Font Version : Version 2.37, Version 5.06, Version 5.06, Version 5.03, Version 5.002;PS 5.002;hotconv 1.0.49;makeotf.lib2.0.15106 Font Composite : False, False, False, False, False Font File Name : ARIALN.TTF, arial.ttf, arialbd.ttf, simsun.ttc, AdobeSongStd-Light.otf Plate Names : Cyan, Magenta, Yellow, Black Swatch Group Name : 默认色板组 Swatch Group Type : 0 Producer : Adobe PDF library 10.01 Page Count : 3 Creator : Adobe Illustrator(R) 16.0 For : yf1, Bounding Box : 23 -591 811 560 Container Version : 11 Creator Version : 16EXIF Metadata provided by EXIF.tools