u blox Malmo 070101 Bluetooth module cB-0701-01 User Manual E M Datasheet OEMSPA Gen2
u-blox Malmo AB Bluetooth module cB-0701-01 E M Datasheet OEMSPA Gen2
Users Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 308145 |
| Application ID | S97mO6LOMv3KsolRoU1Ssw== |
| Document Description | Users Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 63.73kB (796572 bits) |
| Date Submitted | 2003-03-07 00:00:00 |
| Date Available | 2003-03-07 00:00:00 |
| Creation Date | 2003-02-14 15:05:54 |
| Producing Software | Acrobat Distiller 4.05 for Windows |
| Document Lastmod | 2003-02-14 15:24:21 |
| Document Title | E & M Datasheet OEMSPA Gen2 |
| Document Creator | Microsoft Word 9.0 |
| Document Author: | Mats Andersson |
INDUSTRIAL BLUETOOTH™ OEM Serial Port Adapter™ 2nd Generation Electrical & Mechanical Datasheet OEM Serial Port Adapter™ 2nd Generation Electrical & Mechanical Datasheet Copyright © 2002-2003 connectBlue AB. The contents of this document can be changed by connectBlue AB without prior notice and do not constitute any binding undertakings from connectBlue AB. connectBlue AB is not responsible under any circumstances for direct, indirect, unexpected damage or consequent damage that is caused by this document. All rights reserved. Release: 0302 Document version: (1.3) Document number: cBProduct-0212-01 Printed in Sweden. Trademarks Registered trademarks from other companies are: Bluetooth is a trademark owned by the Bluetooth SIG,Inc.Microsoft™, Windows™, Windows NT™, Windows 2000™, Windows CE™, Windows ME™, are registered trademarks from Microsoft Corporation. Contents 1. Introduction 1.1 1.2 1.3 1.4 Related Documents........................................................................... 5 Product Variants ................................................................................ 5 Block Diagram cB-0701-01 ............................................................... 7 Block Diagram cB-0702-01 ............................................................... 7 2. Electrical Interface and Connectors 2.1 2.2 2.3 2.4 2.5 CMOS Logic Levels......................................................................... 12 Signals in J1 and J2 Connector ...................................................... 13 Signals in J3 – J5 Connector .......................................................... 14 Power Control.................................................................................. 14 Interfacing Examples....................................................................... 15 3. Temperature Information 16 4. Bluetooth Information 17 5. Power Consumption 18 6. Antennas 22 6.1 6.2 Surface Mounted Antenna (internal) ............................................... 22 Antennas on a Cable (external antennas)....................................... 23 7. Additional Mounting Instructions 7.1 7.2 7.3 7.4 Antenna Issues................................................................................ 25 Traces and Component Keep out Area........................................... 25 Using the 20-pin 2 mm Pitch Pin Connector ................................... 25 Using Board-to-Board Connectors .................................................. 26 8. Mechanics 8.1 27 Board Outlines................................................................................. 27 9. Regulatory Information 9.1 9.2 25 29 Declaration of Conformity................................................................ 29 FCC Compliance ............................................................................. 30 Chapter 1 Introduction 1.1 Related Documents The picture below shows the relation between the different Serial Port Adapter documents. Serial Port Adapter AT Commands OEM Serial Port Adapter Electrical & Mechanical Datasheet Serial Port Adapter User Manual Bluetooth Enabler Development Kit ECI Specification ECI Driver with connectBlue Extensions User Manual 1.2 ECI Specification with connectBlue Extensions Product Variants This Electrical and Mechanical datasheet contains information about the second generation of OEM Serial Port Adapter. The design consists of two different modules cB-0701-01 (Class 2 / 1 mW / 0 dBm) and cB-0702-01 (Class 1 / 100 mW / 20 dBm). Product Name OEM Module ID Type Description OEMSPA13i cB-0701-01 Class 2 / 0 dBm OEM Serial Port Adapter 13i with internal antenna OEMSPA13x cB-0701-01 Class 2 / 0 dBm OEM Serial Port Adapter 13x with external antenna OEMSPA33i cB-0702-01 Class 1 / 20 dBm OEM Serial Port Adapter 33i with internal antenna OEMSPA33x cB-0702-01 Class 1 / 20 dBm OEM Serial Port Adapter 33x with external antenna cB-0701-01 cB-0701-01 is a small size Bluetooth module based on the Infineon (former Ericsson) PBM 990 80 baseband controller and the PBA 313 05 0dBm radio. The PBM 990 80 has 64 Kbytes on chip SRAM and 512 Kbytes FLASH stacked in the same package. cB-0702-01 cB-0702-01 is a long-range versatile Bluetooth module based on the Infineon (former Ericsson) PBM 990 90 baseband controller and the PBA 313 02 20 dBm radio. The PBM 990 90 has 64 Kbytes on chip SRAM, the FLASH is located in a separate package. cB-0702-01 also contains external SRAM. 1.3 Block Diagram cB-0701-01 Internal antenna Module Interface BluetoothRadio PBA 313 05 (RAN) Base Band Controller PBM990 80 (FLINK) RS-232 Transceiver ADM3315 J1 J2 J6 External Antenna connector EBC radio interface Power supply Vin=3.3-6V J3 Vin=3-6V 1.4 Block Diagram cB-0702-01 Internal antenna Module Interface BluetoothRadio PBA 313 02 (MIRIAN) J6 External Antenna connector FLASH 1 - 8Mbyte DATA[0..15] ADR[1..22] Base Band Controller PBM990 90 (BLINK) RS-232 Transceiver ADM3315 J1 DATA[0..15] ADR[0..23] J2 SRAM 128k - 1Mbyte DATA[0..7] ADR[0..19] Power supply Vin=3.3-6V J3 EBC radio interface J4 J5 Chapter 2 Electrical Interface and Connectors This section describes the signals available on the module interface connectors. There are two ways to connect to the OEM Serial Port Adapter, one is via the J1 connector, a 20-pin 2mm pitch pin header, and the other is via the board-to-board (one piece part) connector, J2 through J5. NOTE! J4 and J5 are only available on cB-0702-01 The J2 to J5 connectors on the OEM Serial Port Adapter exist on the module only as a mating PCB-layout pattern. NOTE! Connectors J3 to J5 are for future use only and will not be covered in details by this document. cB-0701-01 with J1 cB-0702-01 with J1 J1 connector - 20-pin 2mm pitch pin header CB-0702-01 with J2 to J5 (mating PCB-layout pattern) J5 connector J4 connector J3 connector J2 connector J1 connector (back side) J1 connector The figure above shows the pin numbering of the J1 connector. J2 connector The figure shows the bottom view of the two PCBs and the pinning of the J2 connector. J2 motherboard connectors A single-row connector may be used. A connector of the following type is recommended: Samtec: SEI-120-02-GF-S-M-AB The height of this connector is 1.65 mm. Mother board footprint for single row module interface J2 Samtec type: SEI-120-02-GF-S-M-AB PCB-outline cB-0701-01 1.35mm 2 x Ø2.5 mm 2 x Ø1.0 mm 26.62mm 1.0mm 3.81mm 0.5mm 0.56mm PCB-outline cB-0702-01 6.69mm 4.0mm 5.84mm 4.69mm 10.0mm A double-row connector may be used although all the pins needed to use are available on the J2 connector only. The connector is connected to the pins of the J2 and J3 connector. A doublerow connector of the following type is recommended: Samtec: FSI-120-03-G-D-M-AB The height of this connector is 3.00 mm. 10 Mother board footprint for double row module interface J2 & J3 Samtec type: FSI-120-03-G-D-M-AB 2 x Ø1.2 mm J3 1.14mm J2 4.12mm 1.0mm 27.24mm 0.56mm PCB-outline cB-0702-01 2 x Ø2.5 mm 4.38mm 5.28mm 6.38mm PCB-outline cB-0701-01 10.0mm Other connector alternatives maybe used. Use the diagrams above for design help. 11 2.1 CMOS Logic Levels The boards cB-0701-01 and cB-0702-01 has some signals that are defined as logic level CMOS signals. The boards are designed to be fully interchangeable between each other. This is possible if the host product has made space for the cB-0702-01 board. This makes it possible to choose freely between a class 1 or class 2 device without any change of the host product. The following voltage conditions are valid. Signal Voltage level Remark Vin Low min - 0.3 V Vin Low max 0.8 V 0.95 V if only cB-0702-01 is used Vin High min 2.25 V 2.05 V if only cB-0701-01 is used Vin High max 3.2 V 3.5 V if only cB-0702-01 is used Vout Low max 0.1 V Vout High min 2.8 V 12 2.2 Signals in J1 and J2 Connector Maximum load on all In/Out is 3mA. J1 & J2 Pin Name Signal Name Signal Level Type Description VSS Ground Ground VSS Ground Ground VCC_5V Power 3.3V – 6V If only cB-0701-01 is used the range 3.0V – 6.0V is allowed VCC_5V Power 3.3V – 6V If only cB-0701-01 is used the range 3.0V – 6.0V is allowed RS232-CTS Clear To Send RS232 Input RS232-TxD Transmit Data RS232 Output RS232-RTS Request To Send RS232 Output RS232-RxD Receive Data RS232 Input RS232-DTR Data Terminal Ready RS232 Output 10 RS232-DSR Data Set Ready RS232 Input Pin nr. Also used to control the power saving mode “stop mode”. See chapter 2.4 for more information. 11 RED/Mode Red LED output and Serial interface mode select input CMOS In/Out The level on this pin during power up selects RS232 (High) or logic (Low) level UARTcommunication. The Mode pin is only valid at startup and cannot be changed during operation. The Mode pin is internally pulled up i.e. RS232 mode is the default setting. Recommended value of the pull-down resistor is 10 kohm. See section 2.5 for a design example. 12 Switch-0 Function switch CMOS In Used for the “Connect on external signal” function, see the Serial Port Adapter user manual for more information on the Function switch. See section 2.5 for a design example. 13 J1 & J2 Pin Name Signal Name Signal Level Type Description GREEN/Switch-1 Green LED output and Restore switch CMOS If the level on this pin is set to Low the units goes back to default serial settings. Pin nr. 13 In/Out The “Restore Default” input is only active at unit power up. See the Serial Port Adapter user manual for more information on the Restore switch. See section 2.5 for a design example. 14 BLUE Blue LED output CMOS Output See section 2.5 for a design example. 15 UART1-CTS Clear To Send CMOS Input 16 UART1-TxD Transmit Data CMOS Output 17 UART1-RTS Request To Send CMOS Output 18 UART1-RxD Receive Data CMOS Input 19 UART1-DTR Data Terminal Ready CMOS Output 20 UART1-DSR Data Set Ready CMOS Input See Note 1 below. See Note 1 below. Also used to control “stop down mode”. See chapter 2.4 for more information. NOTE1! It is recommended to connect a “pull-up” resistor with the value 82 kohm to 2.8 VDC if UART1-CTS and/or UART-RxD are unconnected or may be left in an undefined state. 2.3 Signals in J3 – J5 Connector These connectors are for future use and not covered by this document.. 2.4 Power Control The DSR signal on the UART and the RS232 interfaces may be used to control “stop mode”. “Stop mode” is the most efficient power saving mode. For more information about “stop mode”, see the Serial Port Adapter User Manual. 14 2.5 Interfacing Examples Example 1 – connection of input/output pins Example 2 – Input/output pins connected to a Host CPU It is recommended to use a serial resistance with a 10 kohm value between the host CPU and the connectBlue module for all input and output pins. NOTE! The RED/Mode pin is a combined output/input pin. The Mode input is only active at power up of the unit. NOTE! The GREEN/Switch 1 pin is a combined output/input pin. The Switch 1 input is only active at power up of the unit. 15 Chapter 3 Temperature Information In the tables below you find information about the different temperature conditions. CB-0701-01 Storage temperature -40 - +85 °C Recommended operating temperature -20 - +75 °C Maximum operating temperature -30 - +75 °C CB-0702-01 Storage temperature -40 - +85 °C Recommended operating temperature -30 - +55 °C Maximum operating temperature -30 - +75 °C 16 Chapter 4 Bluetooth Information In the tables below you find information about product Bluetooth properties. CB-0701-01 Bluetooth Radio Infineon/Ericsson PBD 313 05 (RAN) Bluetooth Base Band Controller Infineon/Ericsson PBM 990 80 (FLINK) RF Output power Class 2, min –2dBm type 1.5dBm max +4dBm Receive sensitive level -80dBm (0.1% BER) Receive input level (Max) Max +14 dBm Output frequency 2.4 –2.5 GHz, ISM band. Point to multi-point operation Yes Bluetooth stack Embedded Host Stack Bluetooth qualification 1.1 CB-0702-01 Bluetooth Radio Infineon/Ericsson PBD 313 02 (MIRIAN) Bluetooth Base Band Controller Infineon/Ericsson PBM 990 90 (BLINK) RF Output power Class 1, min –28dBm, max +17dBm Receive sensitive level -80dBm (0.1% BER) Receive input level (Max) Max +15 dBm Output frequency 2.4 –2.5 GHz, ISM band. Point to multi-point operation Yes Bluetooth stack Embedded Host Stack Bluetooth qualification 1.1 17 Chapter 5 Power Consumption NOTE! The power consumption depends on the UART speed chosen. CB-0701-01 (up to 57,6 kBits/s UART baud rate) Input power is 5 VDC. No external LEDs are connected. UART baud rates up to 57,6 kBits/s. Input voltage : 5V Baudrate <= 57,6 no load on output signals logic level UART signals RS232 circuit enabled loaded (Tx, Rx) RS232 circuit disabled RS232 signals loaded (Tx, RTS, DTR, @3000 ohm/signal) RS232 circuit enabled not connected, not connectable, not discoverable typical mean (mA) : 26.2 typical max (mA) : 26.8 typical mean (mA) : 25.2 typical max (mA) : 25.2 typical mean (mA) : 50.1 typical max (mA) : 50.2 not connected, not connectable, not discoverable, stop mode enabled not connected, connectable, not discoverable not connected, connectable, not discoverable, stop mode enabled not connected, connectable, discoverable not connected, connectable, discoverable, stop mode enabled connected idle, connectable, not discoverable connected send data, connectable, not discoverable typical mean (mA) : 0.7 typical max (mA) : 1.4 typical mean (mA) : 0.6 typical max (mA) : 0.7 typical mean (mA) : 24.5 typical max (mA) : 24.6 typical mean (mA) : 27.4 typical max (mA) : 88.5 typical mean (mA) : 27.2 typical max (mA) : 86.6 typical mean (mA) : 50.7 typical max (mA) : 106.9 typical mean (mA) : 1.1 typical max (mA) : 87.1 typical mean (mA) : 1.1 typical max (mA) : 86.2 typical mean (mA) : 25.3 typical max (mA) : 107.9 typical mean (mA) : 27.9 typical max (mA) : 88.7 typical mean (mA) : 27.8 typical max (mA) : 86.6 typical mean (mA) : 51.1 typical max (mA) : 107.1 typical mean (mA) : 2.3 typical max (mA) : 87.2 typical mean (mA) : 2.3 typical max (mA) : 86.8 typical mean (mA) : 26.0 typical max (mA) : 107.8 typical mean (mA) : 35.8 typical max (mA) : 104.7 typical mean (mA) : 35.6 typical max (mA) : 107.9 typical mean (mA) : 58.6 typical max (mA) : 126.5 N/A typical mean (mA) : 52 typical max (mA) : 106.4 typical mean (mA) : 65 typical max (mA) : 126.5 18 CB-0701-01 (higher than 57,6 kBits/s UART baud rate) Input power is 5 VDC. No external LEDs are connected. UART baud rates higher than 57,6 Input voltage : 5V Baudrate > 57,6 no load on output signals logic level UART signals RS232 circuit enabled loaded (Tx, Rx) RS232 circuit disabled not connected, not connectable, not discoverable not connected, not connectable, not discoverable, stop mode enabled not connected, connectable, not discoverable not connected, connectable, not discoverable, stop mode enabled not connected, connectable, discoverable not connected, connectable, discoverable, stop mode enabled connected idle, connectable, not discoverable connected send data, connectable, not discoverable kBits/s. typical mean (mA) : 60.8 typical max (mA) : 61.4 typical mean (mA) : 61.0 typical max (mA) : 61.0 RS232 signals loaded (Tx,RTS, DTR @3000 ohm/signal) RS232 circuit enabled typical mean (mA) : 83.6 typical max (mA) : 83.6 typical mean (mA) : 0.8 typical max (mA) : 1.6 typical mean (mA) : 0.6 typical max (mA) : 1.3 typical mean (mA) : 24.5 typical max (mA) : 24.6 typical mean (mA) : 63.9 typical max (mA) : 120.5 typical mean (mA) : 64.2 typical max (mA) : 123.5 typical mean (mA) : 86.7 typical max (mA) : 142.6 typical mean (mA) :1.6 typical max (mA) : 88.7 typical mean (mA) : 1.5 typical max (mA) : 87.1 typical mean (mA) : 25.3 typical max (mA) : 107.9 typical mean (mA) : 64.3 typical max (mA) : 121.0 typical mean (mA) : 64.7 typical max (mA) : 123.5 typical mean (mA) : 87.1 typical max (mA) : 154.6 typical mean (mA) : 2.4 typical max (mA) : 88.4 typical mean (mA) : 2.6 typical max (mA) : 92.0 typical mean (mA) : 26.0 typical max (mA) : 107.4 typical mean (mA) : 73.3 typical max (mA) : 141.0 typical mean (mA) : 73.8 typical max (mA) : 155.0 typical mean (mA) : 96.0 typical max (mA) : 172.1 N/A typical mean (mA) : 87.6 typical max (mA) : 156.3 typical mean (mA) : 100 typical max (mA) : 173 19 CB-0702-01 (up to 57,6 kBits/s UART baud rate) Input voltage : 5V Baudrate <= 57,6 no load on output signals logical level UART signals RS232 circuit enabled loaded (Tx, Rx) RS232 circuit disabled RS232 signals loaded (Tx, RTS, DTR, @3000 ohm/signal) RS232 circuit enabled not connected, not connectable, not discoverable typical mean (mA) : 17.6 typical max (mA) : 20.8 typical mean (mA) : 32.6 typical max (mA) : 36.6 typical mean (mA) : 17.5 typical max (mA) : 19.1 not connected, not typical mean (mA) : 0.5 typical mean (mA) : 0.5 typical mean (mA) : 16.3 connectable, not typical max (mA) : 7.4 typical max (mA) : 6.2 typical max (mA) : 20.2 discoverable, stop mode enabled typical mean (mA) : 18.7 typical mean (mA) : 19.0 typical mean (mA) : 33.6 not connected, typical max (mA) : 65.6 typical max (mA) : 65.0 typical max (mA) : 81.3 connectable, not discoverable not connected, typical mean (mA) : 0.7 typical mean (mA) : 0.6 typical mean (mA) : 16.6 connectable, not typical max (mA) : 22.3 typical max (mA) : 22 typical max (mA) : 81.8 discoverable, stop mode enabled typical mean (mA) : 18.7 typical mean (mA) : 18.9 typical mean (mA) : 33.6 not connected, typical max (mA) : 65.6 typical max (mA) : 64.8 typical max (mA) : 81.1 connectable, discoverable not connected, typical mean (mA) : 1.0 typical mean (mA) : 0.5 typical mean (mA) : 16.9 connectable, typical max (mA) : 22.4 typical max (mA) : 21.7 typical max (mA) : 82.2 discoverable, stop mode enabled typical mean (mA) : 27.3 typical mean (mA) : 26.9 typical mean (mA) : 43.0 connected idle, typical max (mA) : 172.9 typical max (mA) : 172.1 typical max (mA) : 193.5 connectable, not discoverable N/A typical mean (mA) : 35 typical mean (mA) : 50.0 connected send data, typical max (mA) : 172.6 typical max (mA) : 194 connectable, not discoverable Input power is 5 V. No external LEDs are connected. UART baud rates up to 57,6 kBits/s. 20 CB-0702-01 (higher than 57,6 kBits/s UART baud rate) Input voltage : 5V Baudrate > 57,6 no load on output signals logical level UART signals RS232 circuit enabled loaded (Tx, Rx) RS232 circuit disabled RS232 signals loaded (Tx,RTS, DTR @3000 ohm/signal) RS232 circuit enabled typical mean (mA) : 53.6 typical max (mA) : 53.6 not connected, not typical mean (mA) : 39.7 typical mean (mA) : 39.6 connectable, not typical max (mA) : 40.1 typical max (mA) : 39.7 discoverable not connected, not typical mean (mA) : 0.6 typical mean (mA) : 0.4 typical mean (mA) : 16.3 connectable, not typical max (mA) : 7.3 typical max (mA) : 5.7 typical max (mA) : 18.9 discoverable, stop mode enabled typical mean (mA) : 41.7 typical mean (mA) : 41.2 typical mean (mA) : 55.6 not connected, typical max (mA) : 89.3 typical max (mA) : 87.9 typical max (mA) : 105.3 connectable, not discoverable not connected, typical mean (mA) : 0.9 typical mean (mA) : 1.1 typical mean (mA) : 16.5 connectable, not typical max (mA) : 65.0 typical max (mA) : 66.1 typical max (mA) : 82.3 discoverable, stop mode enabled typical mean (mA) : 42.1 typical mean (mA) : 42.0 typical mean (mA) : 56.0 not connected, typical max (mA) : 88.1 typical max (mA) : 87.6 typical max (mA) : 105.7 connectable, discoverable not connected, typical mean (mA) : 1.3 typical mean (mA) : 1.1 typical mean (mA) : 17.3 connectable, typical max (mA) : 66.0 typical max (mA) : 66.2 typical max (mA) : 82.4 discoverable, stop mode enabled typical mean (mA) : 49.6 typical mean (mA) : 49.2 typical mean (mA) : 65.4 connected idle, typical max (mA) : 212.3 typical max (mA) : 211.5 typical max (mA) : 234.6 connectable, not discoverable N/A typical mean (mA) : 78 typical mean (mA) : 94.0 connected send data, typical max (mA) : 214.3 typical max (mA) : 237.5 connectable, not discoverable Input power is 5 V. No external LEDs are connected. UART baud rates higher than 57,6 kBits/s. 21 Chapter 6 Antennas There are 2 different antenna options available: • An internal surface mounted (SMD) antenna. • An “antenna on a cable” maybe connected to a U.FL connector. Three different “antennas on a cable” are available. See chapter about Mounting for more info about antenna placement. This chapter gives only an overview of the qualities of the different antenna options. More detailed information is available in the antenna data sheets. 6.1 Surface Mounted Antenna (internal) The unit cannot be mounted in a metal-shielded enclosure with this antenna. cB-0701-01 Polarization Linear cB-0702-01 Polarization Linear 22 6.2 Antennas on a Cable (external antennas) The external antennas are connected to the board through a U.FL connector. Some of the antennas are connected directly to the U.FL connector of the board and some is connected using a SMA connected through a short U.FL to SMA adapter cable. Antenna Accessories Part number cB-ACC-18 Name U.FL to SMA adapter cable Connector U.FL and SMA Comment The SMA connector maybe mounted in a panel. The length is of the cable is 12 cm. Antennas Part number cB-ACC-16 Name WCR-2400SMA Type ½ wave dipole Polarization Vertical Size 10 cm Connector SMA Comment To be mounted on the UF.L to SMA adapter cable. 23 Part number cB-ACC-17 Name Puck Antenna Type Polarization Size 70 mm in diameter. Connector SMA Comment To be mounted on the UF.L to SMA adapter cable. The antenna is mounted with a 16 mm hole through a cabinet wall or ceiling. Part number cB-ACC-19 Name CAP24235 (Microblue) Type Microstrip Polarization Linear Size 21x60 mm. 20 cm cable. Connector U.FL Comment Connected directly to the U.FL connector on OEM board. Part number cB-ACC-20 Name CAF94146 Microsphere Type Microstrip Polarization Linear Size 46x30 mm. 2.5 mm high. 20 cm cable. Connector U.FL Comment Connected directly to the U.FL connector on OEM board. Delivered with a mounting kit. 24 Chapter 7 Additional Mounting Instructions 7.1 Antenna Issues The unit cannot be mounted arbitrary, because of the radio communication. The unit with an internal surface mounted antenna cannot be mounted in a metal enclosure. If a metal enclosure is required, one of the external antenna options has to be used. Use one of the external antenna options if you are using a metallic enclosure or if there are other reasons why the internal antenna cannot be used. See section 6.2 for more information on the antenna options available. A recommended space around the SMD antenna must be free from wires, circuits or other conductive components of the user application. Illustration of a user application OEM Bluetooth module 7.2 Traces and Component Keep out Area The 20-pin 2 mm pitch pin connector (J1) sticks out 1.2 mm below the bottom side of the Serial Port boards. It is recommended to keep traces and components out of this area on the motherboard or keep a safe distance between the motherboard and the Serial Port Adapter board (> 1.6 mm). See chapter 8.1 for detailed measurements and positions for the J1 connector. 7.3 Using the 20-pin 2 mm Pitch Pin Connector If you mount the boards on a motherboard using the mounting holes, distances must be used that is higher than 1.6 mm, this due to the pins of the J1 connector (see chapter 7.2). Chapter 2 contains more information about the connector and the electrical interface. 25 7.4 Using Board-to-Board Connectors Reserved Area Make place for the 20-pin 2 mm pitch pin connector as indicated in chapter 7.2. This allows you to use a standard connectBlue OEM Serial Port Adapter even tough you are not using this connector. Contact connectBlue if there is a requirement to used this reserved area for components. Using the SEI-120-02-GF-S-M-AB Connector from Samtec This connector has a profile height of 1.65 mm and this has to be considered if components are to be mounted on the motherboard under the Serial Port Adapter board. The connector has 2 mm threaded inserts that fit with the mounting holes in the board. You may screw the Serial Port board directly into this inserts. If you want to have a tighter and more secure mounting you may use longer screws and secure it using a nut on the backside of the motherboard. Chapter 2 contains more information about the connector, necessary measurements on the motherboard and the electrical interface. Using the FSI-120-03-G-D-M-AB connector from Samtec This connector has a height of 3.0 mm and this has to be considered if components are to be mounted on the motherboard under the Serial Port Adapter board. The connector has 2 mm threaded inserts that fit with the mounting holes in the board. You may screw the Serial Port board directly into this inserts. If you want to have a tighter and more secure mounting you may use longer screws and secure it using a nut on the backside of the motherboard. Chapter 2 contains more information about the connectors, mounting measurements and the electrical interface. 26 Chapter 8 Mechanics 8.1 Board Outlines 0.9 mm PCB-outline cB-0701-01 0.9 mm The smaller board cB-0701-01 is 36x23x1.45 mm. The larger board is 40x42x1.45 mm. The height of the module is maximum 5 mm. No components are mounted on the secondary side of the module. 27 PCB-outline cB-0702-01 28 Chapter 9 Regulatory Information NOTE! Regulatory certification is in progress. 9.1 Declaration of Conformity We, connectBlue AB, of Stora Varvsgatan 11 N:1 SE-211 19 Malmö, Sweden declare under our sole responsibility that our products: OEM Serial Port Adapter 13i, cB-0032-01, OEM Serial Port Adapter 13x, cB-0033-01 OEM Serial Port Adapter 33i, cB-0034-01, OEM Serial Port Adapter 33x, cB-0035-01 Serial Port Adapter 12i, cB-0036-01, Serial Port Adapter 32i, cB-0037-01 Serial Port Adapter 33i, cB-0041-01, Serial Port Adapter 33c, cB-0038-01 Rugged Serial Port Adapter 32s, cB-0039-01, OEM Module Adapter 2, cB-0040-01 to which this declaration relates, conforms to the following product specifications: R&TTE Directive 1999/5/EC EN 300 328-2 V1.1.1 (2000-07) EMC Directive: 89/336/EEC EN 301 489-1 V1.3.1 (2001-09) EN 301 489-17 V1.1.1 (2000-09) Low Voltage Directive: 73/23/EEC EN 61131-2 Medical Electrical Equipment IEC 60601-1-2 A notification must be made to each of the national authorities responsible for radio spectrum management of the intention to place radio equipment that uses frequency bands whose use is not harmonized throughout the EU, on its national market. More information at: http://europa.eu.int/comm/enterprise/rtte/gener.htm 29 9.2 FCC Compliance FCC Statement for cB-0701-01 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna • Increase the separation between the equipment and receiver • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected • Consult the dealer or an experienced radio/TV technician for help Labeling Requirements for End Product For an end product using the OEM Serial Port Adapter or the OEM Bluetooth Enabler there must be a label containing, at least, the following information: This device contains FCC ID: PVH070101 The label must be affixed on an exterior surface of the end product such that it will be visible upon inspection in compliance with the modular approval guidelines developed by the FCC. In addition, the user manual for the end product must contain the following information: “This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.” Antenna When using the module equipped with the external antennas as described previously the antenna is fixed and cannot be removed or replaced by the end user. Caution Any changes or modifications NOT explicitly APPROVED by connectBlue AB could cause the module to cease to comply with FCC rules part 15, and thus void the user’s authority to operate the equipment. 30 FCC Statement for cB-0702-01 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna • Increase the separation between the equipment and receiver • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected • Consult the dealer or an experienced radio/TV technician for help Labeling Requirements for End Product For an end product using the OEM Serial Port Adapter or the OEM Bluetooth Enabler there must be a label containing, at least, the following information: This device contains FCC ID: PVH070201 The label must be affixed on an exterior surface of the end product such that it will be visible upon inspection in compliance with the modular approval guidelines developed by the FCC. In addition, the user manual for the end product must contain the following information: “This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.” Antenna When using the module equipped with the external antennas as described previously the antenna is fixed and cannot be removed or replaced by the end user. Caution Any changes or modifications NOT explicitly APPROVED by connectBlue AB could cause the module to cease to comply with FCC rules part 15, and thus void the user’s authority to operate the equipment. 31
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.3 Linearized : No Producer : Acrobat Distiller 4.05 for Windows Creator : Microsoft Word 9.0 Keywords : 0-1 Modify Date : 2003:02:14 15:24:21+01:00 Subject : cBProduct-0212-01 Create Date : 2003:02:14 15:05:54 Title : E & M Datasheet OEMSPA Gen2 Author : Mats Andersson Page Count : 31 Page Mode : UseNoneEXIF Metadata provided by EXIF.tools