u blox WIBEAR11N-DF1 Bluetooth & WLAN Module User Manual WiBear11n DS

u-blox AG Bluetooth & WLAN Module WiBear11n DS

UserManual.wiki >

WIBEAR11N-DF1 User Manual >

Contents

1. user manual
2. User Manual
3. ELLA-W1_Antenna TraceDesigns_(UBX-16016269)

User Manual

The information in this document is subject to change without notice. Please download latest version from www.lesswire.com Copyright © 2014 lesswire AG www.lesswire.com WiBear11n IEEE 802.11a/b/g/n WLAN, Bluetooth 3.0+EDR Module Data Sheet Version 1.20 October 2014

WiBear11n Data SheetVersion 1.20 Copyright © 2014 lesswire AG www.lesswire.com Page 2 of 20 Introduction The WiBear11n industrial universal module is targeted for integration into different OEM products. The module is designed for both simultaneous and independent operation of the following: IEEE 802.11a/b/g/n payload data rates for Wireless Local Area Network (WLAN), Bluetooth 3.0+High Speed (HS) and Bluetooth 2.1+EDR. It provides a complete end-to-end solution for low-power applications. It includes an integrated MAC/Baseband processor and RF front-end components and can connect to a host processor through an SDIO interface. The WiBear11n modules are offered in four versions (see ordering information and block diagram). Host drivers for common operating systems such as Linux and Windows 7 are available. The modules are radio type approved for Europe (CE), US (FCC) and Industry Canada (IC) (pending). Applications  WLAN and Bluetooth networks  Audio/video devices and accessories  Access to laptops, mobile phones etc.  Automotive and industrial networking  Home / building automation Key Features  Standards: IEEE 802.11a/b/g/n/e/i/h/d/k/r/w  WLAN 802.11a/b/g/n station and micro access point operation (up to 8 clients supported)  Support of Wi-Fi direct mode  802.11n 1x1 SISO  802.11 PHY data rates up to 72 Mbps (20 MHz channel) and up to 150 Mbps (40 MHz channel)  Hardware 64- and 128-bit encryption AES engine performance  Embedded security supplicant  WAPI encryption is supported by hardware  Background scan mode  Bluetooth 3.0 + HS (High Speed)  Bluetooth 2.1 + EDR (backward compatibility)  Wide temperature operation range -40ºC to +85ºC  Compact 14.8mm x 14.8mm footprint, surface mounting  SDIO high-speed interface  Support for low-power modes  CE/FCC/IC compliant  RoHS compliant  Automotive qualification tests (climatic, mechanical, and operating life tests) according to VW 80000 / ISO 16750-4 (report pending) Figure 1: Physical outlook

WiBear11n Data SheetVersion 1.20 Copyright © 2014 lesswire AG www.lesswire.com Page 3 of 20 Ordering Information Table 1: Ordering information Order Number Model Description AN00J93170 WiBear11n-SF1 WiBear11n-SF1 Module AN00J93174 WiBear11n-SF2 WiBear11n-SF2 Module AN00J93172 WiBear11n-DF1 WiBear11n-DF1 Module AN00J93176 WiBear11n-DF2 WiBear11n-DF2 Module AN00J94359 WiBear11n-SF1 WiBear11n-SF1 Module, tape&reel package (500 pcs) AN00J94361 WiBear11n-SF2 WiBear11n-SF2 Module, tape&reel package (500 pcs) AN00J94360 WiBear11n-DF1 WiBear11n-DF1 Module, tape&reel package (500 pcs) AN00J94362 WiBear11n-DF2 WiBear11n-DF2 Module, tape&reel package (500 pcs) AN00J93704 WiBear11n-DF1_EK Evaluation Kit with WiBear11n-DF1 Module AN00J93705 WiBear11n-DF2_EK Evaluation Kit with WiBear11n-DF2 Module Note: Shielded modules available on special request. IMDS number: 355902511 Customs Tariff Numbers: HTC / TARIC: 85177090 ECCN number: 3A001 EORI no.: DE4665759 Product Variants Table 2: Product variants Model Description WiBear11n-SF1 Single-band WLAN (IEEE 802.11 b/g/n, 2.4 GHz only) and Bluetooth module. Module has one joint antenna connector for WLAN and Bluetooth operation (see block diagram). WiBear11n-SF1/-DF1 is recommended for cost effective AP solution, AP without or rare Bluetooth traffic or cost effective station with one system antenna. WiBear11n-SF2 Single-band WLAN (IEEE 802.11 b/g/n, 2.4 GHz only) and Bluetooth module. Module has separated antenna connectors for WLAN and Bluetooth operation (see block diagram). Overall performance (throughput) is maximized for AP mode with simultaneous Bluetooth traffic. Two system antennas are required (one for WLAN and one for Bluetooth) with 30 dB or better isolation between antennas (orthogonal oriented antennas with more than 50…60 mm. distance between). May be recommended for higher performance of AP. WiBear11n-DF1 Dual-band WLAN (IEEE 802.11 a/b/g/n, 2.4 and 5 GHz) and Bluetooth module with one joint antenna connector for WLAN and Bluetooth. Similar to WiBear11n-SF1. WiBear11n-DF2 Dual-band WLAN (IEEE 802.11 a/b/g/n, 2.4 and 5 GHz) and Bluetooth module which has separated antenna connectors for WLAN and Bluetooth. Similar to WiBear11n-SF2. Note: For maximum throughput during simultaneous WLAN (AP) and Bluetooth operation, the Bluetooth Coexistence Arbiter (BCA) settings should be optimized by the host system software.

WiBear11n Data SheetVersion 1.20 Copyright © 2014 lesswire AG www.lesswire.com Page 4 of 20 Block Diagrams WiBear11n-SF1 WiBear11n-SF2 802.11b/g/n MAC/BB/RADIOBLUETOOTH 3.0+HS2.4 GHzRF FRONTEND2.5GHz WLAN TX2.5GHz WLAN/BT RXBT TXWLAN &BT ANTVIO1.8V3.3V2.5GHz2.4GHzBPFWiBear11n-SF1EEPROM38.4MHzCrystalSDIORESETnPDnSLEEPCLOCKGPIOs802.11b/g/n MAC/BB/RADIOBLUETOOTH 3.0+HSEEPROMSDIO38.4MHzCrystal2.4 GHzRF FRONTEND2.5GHz WLAN TX2.5GHz WLAN RXBT TX/RXWLAN ANTRESETnPDnVIO1.8V3.3V2.5GHz2.4GHzBPFSLEEPCLOCKWiBear11n-SF2BT ANT2.4GHzBPFGPIOsFigure 2: Block diagram of WiBear11n-SF1 Figure 3: Block diagram of WiBear11n-SF2

WiBear11n Data SheetVersion 1.20 Copyright © 2014 lesswire AG www.lesswire.com Page 5 of 20 WiBear11n-DF1 WiBear11n-DF2 802.11a/b/g/n MAC/BB/RADIOBLUETOOTH 3.0+HS2.4 GHzRF FRONTEND2.5GHz WLAN TX2.5GHz WLAN/BT RXBT TXWLAN &BT ANTVIO1.8V3.3V5GHz WLAN TX5GHz WLAN RX5 GHzRF FRONTEND5GHz BPF&DIPLEXER5GHz2.5GHz2.4GHzBPFWiBear11n-DF1EEPROMSDIO38.4MHzCrystalRESETnPDnSLEEPCLOCKGPIOs802.11a/b/g/n MAC/BB/RADIOBLUETOOTH 3.0+HS2.4 GHzRF FRONTEND2.5GHz WLAN TX2.5GHz WLAN RXBT TX/RXWLAN ANTVIO1.8V3.3V5GHz WLAN TX5GHz WLAN RX5 GHzRF FRONTEND5GHz BPF&DIPLEXER5GHz2.5GHz2.4GHzBPFWiBear11n-DF2BT ANT2.4GHzBPFEEPROMSDIO38.4MHzCrystalRESETnPDnSLEEPCLOCKGPIOsFigure 4: Block diagram of WiBear11n-DF1 Figure 5: Block diagram of WiBear11n-DF2

WiBear11n Data SheetVersion 1.20 Copyright © 2014 lesswire AG www.lesswire.com Page 6 of 20 Pin Description Table 3: Pin description Pin No. Pin Name Pin Type Description 1 GND Ground Ground 2 LED_0 I/O LED output (GPIO_1 of Radio/Baseband processor), WLAN activity 1 3 LED_1 I/O LED output (GPIO_17 of Radio/Baseband processor), Bluetooth activity 1 4 3V3 Power 3.3V Power supply (3.0V...3.6V) 5 VIO Power VIO Supply (1.8V or 3.3V) 6 1V8 Power 1.8V Supply (1.7V...1.9V) 7 GND Ground Ground 8 GND Ground Ground 9 PDn I Full power down (active low), has internal pull-up to VIO pin 10 RESETn I Reset (active low), has weak internal pull-up to VIO pin 11 SD_D2 I/O SDIO Data line bit [2] 12 SD_D3 I/O SDIO Data line bit [3] 13 SD_CMD I/O SDIO Command 14 SD_CLK I SDIO Clock input 15 SD_D0 I/O SDIO Data line bit [0] 16 SD_D1 I/O SDIO Data line bit [1] 17 GND Ground Ground 18 GND Ground Ground 19 SLEEP_CLK I Clock input for external sleep clock source (32.768kHz) 2 20 CFG I/O Configuration pin 3 21 PCM_SYNC I/O GPIO_14 of Radio/Baseband processor, output if master, input if slave 22 PCM_CLK I/O GPIO_13 of Radio/Baseband processor, output if master, input if slave 23 PCM_DOUT O GPIO_12 of Radio/Baseband processor, output 24 PCM_DIN I GPIO_11 of Radio/Baseband processor, input 25 GND Ground Ground GNDLED_0LED_13V3VIO1V8GNDGND12345678PDnRESETnSD_D2SD_D3SD_CMDSD_CLKSD_D0SD_D11415161011121392423222120191817GNDGNDSLEEP_CLKCFGPCM_SYNCPCM_CLKPCM_DOUTPCM_DIN302928272625GNDANT2GNDGNDANT1GNDFigure 6: Module pinout

WiBear11n Data SheetVersion 1.20 Copyright © 2014 lesswire AG www.lesswire.com Page 7 of 20 26 ANT2 I/O, RF Bluetooth antenna for WiBear11n-SF2/-DF2 module, at WiBear-SF1/-DF1 not connected 27 GND Ground Ground 28 GND Ground Ground 29 ANT1 I/O, RF WLAN + Bluetooth antenna for WiBear11n-SF1/-DF1 module, WLAN only antenna for WiBear11n-SF2/-DF2 module 30 GND Ground Ground NOTES: 1 Possible to use as a LED output depend on firmware (driver) version. Regardless of the I/O supply (1.8V or 3.3V), the supply to the actual board LED always need to use 3.3V on the other end of the LED and works as open drain circuitry in that case. LED current limiting resistor should be used. Maximum sink to the ground current - 10 mA. 2 Should be provided from external source in case of power save operation modes necessity. Not required for full power mode and for automotive use (firmware & driver version 14.44). Mandatory for all other releases with sleep mode support. Sleep clock signal requirements: frequency 32.768kHz ±250ppm, low level from 0 to 0.25V, high level from 0.8 to 2.0V, duty cycle 20-80%, slew rate less than 100nS (10-90%). 3 Leave it unconnected when 32.768KHz Sleep Clock provided, pull down by 47K resistor for Sleep Clock less operation.

WiBear11n Data SheetVersion 1.20 Copyright © 2014 lesswire AG www.lesswire.com Page 8 of 20 Electrical Specifications Absolute Maximum Ratings Table 4: Absolute maximum ratings Name Parameter Min Max Units 3V3 Power supply voltage 3.3V -0.3 3.6 V 1V8 Power supply voltage 1.8V -0.3 2.0 V VIO I/O supply voltage 1.8V/2.6/3.3V -0.3 3.6 V TSTORAGE Storage temperature -40 +85 ºC Operating Conditions Table 5: Operating conditions Name Parameter Min Typ Max Units 3V3 Power supply voltage 3.3V 3.1 3.3 3.6 V 1V8 Power supply voltage 1.8V 1.74 1.8 1.89 V VIO I/O supply voltage 1.8V/3.3V 1.62 1.8 1.98 V 3.0 3.3 3.6 V TA Ambient operating temperature -40 - +85 ºC Ripple Noise Peak-to-peak voltage ripple on 3V3 and 1V8 supply lines. - - 10 mV Digital Pad Ratings Table 6: Digital pad ratings Name Parameter Mode1 Min Max Units VIH Input high voltage 1.8V 0.8*1V8 1V8+0.3 V 3.3V 0.7*3V3 3V3+0.3 V VIL Input low voltage 1.8V -0.3 0.3*1V8 V 3.3V -0.3 0.3*3V3 V VHYS Input hysteresis 1.8V 150 - mV 3.3V 200 - mV VOH Output high voltage 1.8V 1V8-0.4 - V 3.3V 3V3-0.4 - V VOH Output low voltage 1.8V - 0.4 V 3.3V - 0.4 V Note: 1IO voltage, see table above for possible IO voltage range. Current Consumption Table 7: Current consumption Operation mode Current, mA1 1.8V VIO2 3.3V RX 2.4GHz 145 10 0.1 5GHz 150 10 14 TX 2.4GHz +18dBm 140 10 200 +15dBm 140 10 170 +12dBm 140 10 145 +6dBm 140 10 120 5GHz +15dBm 150 10 200 +12dBm 150 10 170 +6dBm 150 10 150 Notes: 1 Peak values shown, average current for full operation mode (not a power save mode) strongly depend on RX/TX time ratio and remain in range between peak values of RX and TX. 2 VIO current shown for 3.3V I/O voltage.

WiBear11n Data SheetVersion 1.20 Copyright © 2014 lesswire AG www.lesswire.com Page 9 of 20 Radio Specifications WLAN Module supports dual-band 802.11b/g/n and 802.11a/n operation in both 2.4 GHz and 5 GHz radio bands, respectively. Therefore the module is designed to operate in only one frequency band at time. Table 8: WLAN radio specifications Parameter Operation mode Specification RF Frequency Range 802.11b/g/n 2.400 – 2.500 GHz 802.11a/n 4.900 – 5.825 GHz Modulation 802.11b CCK and DSSS 802.11a/g/n OFDM Supported Data Rates 802.11b 1, 2, 5.5, 11 Mbps 802.11a/g 6, 9, 12, 18, 24, 36, 48, 54 Mbps 802.11n MCS0 - MCS7 Supported Bandwidth 802.11n 20, 40 MHz Supported Guard Interval 802.11n 400, 800 mS Maximum Transmit Power 802.11b 18 dBm ± 1 dB 802.11a/g/n 15 dBm ± 1 dB Receiver Sensitivity 2.4 GHz 802.11b 1 Mbps -96 dBm ± 1 dB 11 Mbps -87 dBm ± 1 dB 802.11g 6 Mbps -89 dBm ± 1 dB 54 Mbps -71 dBm ± 1 dB 802.11n 20 MHz MCS0 -88 dBm ± 1 dB MCS7 -69 dBm ± 1 dB 40 MHz MCS0 -85 dBm ± 1 dB MCS7 -66 dBm ± 1 dB 5 GHz 802.11a 6 Mbps -92 dBm ± 1 dB 54 Mbps -75 dBm ± 1 dB 802.11n 20 MHz MCS0 -91 dBm ± 1 dB MCS7 -72 dBm ± 1 dB 40 MHz MCS0 -89 dBm ± 1 dB MCS7 -69 dBm ± 1 dB Table 9: 2.4 GHz Band Supported Channels, 20MHz bandwidth Channel Frequency, GHz Channel Frequency, GHz Channel Frequency, GHz 1 2.412 6 2.437 11 2.462 2 2.417 7 2.442 12 2.467 3 2.422 8 2.447 13 2.472 4 2.427 9 2.452 141 2.484 5 2.432 10 2.457 Note: 1Channel 14 supported at 802.11b mode only Table 10: 2.4 GHz Band Supported Channels, 40MHz bandwidth Channel Frequency, GHz Channel Frequency, GHz Channel Frequency, GHz 1 5 2.422 4 8 2.437 7 11 2.452 2 6 2.427 5 9 2.442 3 7 2.432 6 10 2.447

WiBear11n Data SheetVersion 1.20 Copyright © 2014 lesswire AG www.lesswire.com Page 10 of 20 Table 11: 5 GHz Band Supported Channels, 20MHz bandwidth Channel Frequency, GHz Channel Frequency, GHz Channel Frequency, GHz 36 5.180 100 5.500 132 5.660 40 5.200 104 5.520 136 5.680 44 5.220 108 5.540 140 5.700 48 5.240 112 5.560 149 5.745 52 5.260 116 5.580 153 5.765 56 5.280 120 5.600 157 5.785 60 5.300 124 5.620 161 5.805 64 5.320 128 5.640 165 5.825 Table 12: 5 GHz Band Supported Channels, 40MHz bandwidth Channel Frequency, GHz Channel Frequency, GHz Channel Frequency, GHz 36 40 5.190 100 104 5.510 132 136 5.670 44 48 5.230 108 112 5.550 149 153 5.755 52 56 5.270 116 120 5.590 157 161 5.795 60 64 5.310 124 128 5.630 Bluetooth Table 13: Bluetooth Radio specifications Parameter Specification RF Frequency Range 2.400 – 2.4835 GHz Supported Modes BT 2.1 EDR, BT3.0 HS Number of channels 79 Modulation 1 Mbps: GFSK (BDR) 2 Mbps: π/4 DQPSK (EDR) 3 Mbps: 8DQPSK (EDR) Transmit Power +8 dBm ± 1.5 dB Receiver Sensitivity BDR: -90 dBm ± 1.5 dB EDR: -87 dBm ± 1.5 dB

WiBear11n Data SheetVersion 1.20 Copyright © 2014 lesswire AG www.lesswire.com Page 11 of 20 Physical Dimensions Note: The tolerances +/- 0.1 mm may be exceeded in the corners of the PCB due to the cutting process. In worst case, the outer dimensions could reach 15.1 mm. Recommended Footprint Figure 7: Physical dimensions Figure 8: Recommended footprint 14215 1610 11 12 1393456781232221201918172426 251.60.60.814.8Pitch=1.2714.827282930

WiBear11n Data SheetVersion 1.20 Copyright © 2014 lesswire AG www.lesswire.com Page 12 of 20 Host Interfaces SDIO Interface WiBear11n module supports a SDIO device interface that conforms to the industry standard SDIO Full-Speed specification and allows a host controller using the SDIO bus protocol to access the WLAN and Bluetooth functions. The module also supports High Speed mode as defined in the SDIO 1.2 specification. The module's SDIO host interface pins are powered from the VIO voltage supply. A module acts as the device on the SDIO bus. The SDIO interface supports SDIO modes at the full clock range of 0 to 50 MHz which allows a maximum throughput of 200Mbps. ClockTWHfPPInputOutputTWLTISUTIHTODLYTOHClockTWHfPPInputOutputTWLTISUTIHTODLYFigure 9: SDIO Protocol Timing Diagram Figure 10: SDIO Protocol Timing Diagram at High Speed Mode

WiBear11n Data SheetVersion 1.20 Copyright © 2014 lesswire AG www.lesswire.com Page 13 of 20 Table 14: SDIO Host Interface Timing Data Symbol Parameter Condition Min Typ Max Units fPP Clock Frequency Normal 0 - 25 MHz High Speed 0 - 50 MHz TWL Clock Low Time Normal 10 - - ns High Speed 7 - - ns TWH Clock High Time Normal 10 - - ns High Speed 7 - - ns TISU Input Setup Time Normal 5 - - ns High Speed 6 - - ns TIH Input Hold Time Normal 5 - - ns High Speed 2 - - ns TODLY Output Delay Time Normal - - 14 ns High Speed - - 14 ns TOH Output Hold Time High Speed 2.5 - - ns

WiBear11n Data SheetVersion 1.20 Copyright © 2014 lesswire AG www.lesswire.com Page 14 of 20 Reference Design Overview Reference design shows how to connect a WiBear11n module to the host controller. WLAN and Bluetooth (BT3.0 HS + EDR) may be connected to the host simultaneously over the SDIO bus. The layout is equipped with the possibility to either use an onboard antenna or an external antenna connected via coaxial connector by means of setting of jumper R7 or R8. Host interface voltage can also be changed by jumper J6. The ready-made reference design is available as WiBear11n Evaluation Kit from Lesswire AG. Schematic Diagram C1100nFD3BlueD1GreenD2OrangeJ2IN1EN3GND2NC 4OUT 5U2MCP1824T-1802EDAT2 9DAT3 1CMD 2GND 3VDD 4CLK 5GND 6DAT0 7DAT1 8SDIO1 23 45 67 89 1012141113J1R1360 R2620C210uF3V3R33.6k3V3MAINJ3AUXLED_1LED_03V31V83V3RESETSD_D2SD_D3CMDCLKSD_D0SD_D13V33V3SD_D2SD_D3CMDCLKSD_D0SD_D1SD_D2SD_D3CMDCLKSD_D0SD_D1SDIOAssemblyOption DescriptionWLAN and Bluetooth at the same antenna terminal (U1:Pin 44)WLAN and Bluetooth at the different antenna terminals12J3"Supply" "WLAN" "BT"DNP+R70U1WiBear11n-DF1(U1:Pin 29 and U1:Pin 26 correspondingly) for uAP functionalityWiBear11n-SF1RESETWiBear11n-DF2WiBear11n-SF2SLP_CLKSLP_CLKC310uFRESET 1MR3GND 2CT4SENSE5VDD 6U3TPS3808G30LED_0LED_11V8J6J4R647KCFGCFGA1Dual BandAntennaJ5R410KC4100nF3V3 VIOR510KRESET1V83V3VIOJ7J8R8DNP20mS Reset PulseC72.2pFL16.8nH L212nHEN1GND 2OUT 3VCC4Y132.768kHzC6100nF10mS Start Up TimeSD_D211SD_D312SD_CMD13SD_CLK14SD_D015SD_D116RESET10 PD93V34VIO51V86GND 1GND 7SLP_CLK19LED_13PCM_DOUT23 PCM_CLK22GND 8LED_02CFG20PCM_SYNC21GND 17ANT2 26GND 18PCM_DIN24ANT1 29GND 25GND 27GND 28GND 30U1WiBear11nC5DNPAntenna matching components (L1, C7, L2)values depend on antenna type,layout, PCB material and PCB thickness123123Figure 11: Evaluation Kit outlook Figure 12: Evaluation kit schematic diagram

WiBear11n Data SheetVersion 1.20 Copyright © 2014 lesswire AG www.lesswire.com Page 15 of 20 Assembly diagram Bill of Materials Table 15: Bill of materials Qty Designator Part Description Manufacturer Part Number 1 A1 Antenna CHIP 2.45 & 5 GHz, 10.4x10.4x0.8mm Antenova: A10194 3 C1, C4, C6 CAP, CER, 100nF, 10%, X7R, 16V, SMD 0402 Generic Components 2 C2, C3 CAP, CER, 10uF, 20%, X5R, 6.3V, SMD 0603 Generic Components 1 C5 DNP Generic Components 1 C7 CAP, CER, 2.2pF, +/-0.25pF, C0G, 50V, SMD 0402 Generic Components 1 D1 LED, Green, SMD 0603 Avago: HSMG-C190 1 D2 LED, Orange, SMD 0603 Avago: HSMD-C190 1 D3 LED, Blue, SMD 0603 Avago: HSMR-C190 1 J1 Pin Header, Double Row, 2.54mm pitch, Straight, 2x7 Way, Through Hole Generic Components 2 J2, J3 Coaxial Connector, 0 - 6GHz, SMD Hirose: U.FL-R-SMT 2 J4, J6 Pin Header, Pitch 2.0mm, 1x3 Way, Through Hole Samtec: TMM-103-01-G-S 3 J5, J7, J8 Pin Header, Pitch 2.0mm, 1x2 Way, Through Hole Samtec: TMM-102-01-G-S 1 L1 IND, Multilayer Ceramic, 6.8nH, +/-5%, 300mA, SMD 0402 Generic Components 1 L2 IND, Multilayer Ceramic, 12nH, +/-5%, 300mA, SMD 0402 Generic Components 1 PCB PCB, Dual side, 82x24x1.5mm, Rev.1A Lesswire AG: WiBear11n_EK_R1 1 R1 RES, 360 Ohm, 5%, 1/16W, SMD 0402 Generic Components 1 R2 RES, 620 Ohm, 5%, 1/16W, SMD 0402 Generic Components 1 R3 RES, 3.6k, 5%, 1/16W, SMD 0402 Generic Components 2 R4, R5 RES, 10k, 5%, 1/16W, SMD 0402 Generic Components 1 R6 RES, 47K, 5%, 1/16W, SMD 0402 Generic Components 2 R7, R8 RES, 0 Ohm, 1/16W, SMD 0402 Generic Components 1 U1 WLAN 802.11a/b/g/n and Bluetooth Module, 14.8x14.8x2.5mm Lesswire AG: WiBear11n 1 U2 CMOS LDO Voltage Regulator 1.8V 300mA, SOT23-5 Microchip: MCP1824T-1802E/OT 1 U3 Voltage supervisor, programmable reset time, threshold voltage 2.79V, SOT23-6 Texas Instruments: TPS3808G30 1 Y1 Quartz Oscillator, 32.768kHz, 1.8V, +/-50ppm, -40...+85C, SMD 3.2x2.5x1.0mm Pericom: KK3270049 Figure 13: Evaluation kit assembly diagram

WiBear11n Data SheetVersion 1.20 Copyright © 2014 lesswire AG www.lesswire.com Page 17 of 20 Installation and Regulatory Information General The purpose of this guide is to explain how to integrate the WiBear11n module into the end product. The module has to be installed and used in accordance with the technical instructions provided by the manufacturer. The module may only be implemented in the configuration that was authorized. Note that any modifications of this equipment not expressly approved by the manufacturer could void the user’s authority to operate the equipment. European Union Regulatory Compliance The WiBear11n module has been tested and complies with the regulatory standards EN 300 328 and EN 301 489-1/-17. We declare that the human exposure of this module is below the SAR limits specified in the EU recommendations 1999/519/EC. IMPORTANT: The ‘CE’ marking must be affixed to a visible location on the OEM product, where this module is installed in, and has to be labeled in accordance to R&TTE Directive 1999/5/EC. FCC Compliance This device complies with Part 15 of the FCC Rules1. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Not authorized modification could void authority to use this equipment. The internal / external antenna(s) used for this module must provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. NOTE: The outside of final product that contain a WiBear11n module must display in a user accessible area a label referring to the enclosed module. This exterior label can use wording such as the following: “Contains Transmitter Module FCC ID: PV7-WIBEAR11N-SF1”2 or “Contains FCC ID: PV7-WIBEAR11N-SF1”. IMPORTANT: The approval type for the WiBear11n variants is a limited modular approval due to the absence of a shielding. This requires any manufacturer of original equipment containing the WiBear11n module to ask for an approval of their design by the manufacturer of the WiBear11n module. IC Compliance This device complies with Industry Canada RSS-210 (Rev. 8). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. The installer of this radio equipment must ensure that the antenna is located or pointed such that it does not emit RF field in excess of Health Canada limits for the general population; consult Safety Code 6, obtainable from Health Canada. Not authorized modification could void authority to use this equipment. 1 Limited modular approval has been applied for the module variant WiBear11n-SF1, the certification process for the other module variants is ongoing. 2 FCC and IC IDs for the WiBear11n module variants are shown in Table 19. Select the applicable ID.

WiBear11n Data SheetVersion 1.20 Copyright © 2014 lesswire AG www.lesswire.com Page 18 of 20 The internal / external antenna(s) used for this module must provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. NOTE: The outside of final product that contain a WiBear11n module must display in a user accessible area a label referring to the enclosed module. This exterior label can use wording such as the following: “Contains Transmitter Module IC ID: 7738A-WB11NSF1”2 or “Contains IC ID: 7738A-WB11NSF1”. IMPORTANT: The approval type for the WiBear11n variants is a limited modular approval due to the absence of a shielding. Due to Industry Canada Modular Approval Requirements (Source: RSS-Gen / Issue 3 / Dec. 2010) any application which includes the WiBear11n module must be approved by the module manufacturer (lesswire AG). The application manufacturer must provide design data for the review procedure. Approved Antennas List For Bluetooth and WLAN operation in the 2.4 GHz band, the module has been tested and approved for use with the antenna listed in the table below. Table 17: Approved antennas list, single-band operation Model Name Manufacturer and description Gain [dBi] (peak) 2450AT45A100 Johanson Technology, chip antenna, 2400 – 2500 MHz 3.0 ANT-2.4-CW-RH Linx, monopole antenna, 2390 – 2490 MHz -0.9 ANT-2.4-CW-RCT-RP Linx, dipole antenna, 2390 – 2510 MHz 2.2 GW26.0151 Taoglas, monopole antenna, 2400 – 2500 MHz 1.8 For Bluetooth, WLAN operation in the 2.4 GHz band, and WLAN operation in the 5 GHz band, the module has been tested and approved for use with the antenna listed in the table below. Table 18: Approved antennas list, dual-band operation Model Name Manufacturer and description Gain [dBi] (peak) A10194 Antenova, dual-band SMD antenna, 2.4 – 2.5 GHz and 4.9 – 5.9 GHz 1.8 @ 2.4 GHz band 4.1 @ 5 GHz band ANT-DB1-RAF-RPS Linx, dual-band dipole antenna, 2400 – 2483 MHz and 5150 – 5825 GHz 2.675 @ 2.4 GHz band 4.599 @ 5 GHz band GW40.2153 Taoglas, dual-band dipole antenna, 2400 – 2500 MHz and 5150 – 5850 GHz 3.74 @ 2.4 GHz band 2.5 @ 5 GHz band GW59.3153 Taoglas, dual-band dipole antenna, 2400 – 2500 MHz and 5150 – 5850 GHz 2.37 @ 2.4 GHz band 2.93 @ 5 GHz band The module may be integrated with other antennas which the OEM installer must authorize with respective regulatory agencies and after approval of the module manufacturer. FCC and IC IDs Table 19: FCC and IC IDs for WiBear11n module variants Model Model number FCC ID IC ID WiBear11n-SF1 AN00J93170 PV7-WIBEAR11N-SF1 7738A-WB11NSF1 WiBear11n-SF2 AN00J93174 PV7-WIBEAR11N-SF2 7738A-WB11NSF2 WiBear11n-DF1 AN00J93172 PV7-WIBEAR11N-DF1 7738A-WB11NDF1 WiBear11n-DF2 AN00J93176 PV7-WIBEAR11N-DF2 7738A-WB11NDF2 Label Due to the small module size, the FCC and IC IDs cannot be displayed on the label. The corresponding FCC and IC IDs for the module variants are shown in the table above.

WiBear11n Data SheetVersion 1.20 Copyright © 2014 lesswire AG www.lesswire.com Page 19 of 20 Label drawing: Label location: Figure 15: Label and label location Bluetooth Qualification WiBear11n is listed at the Bluetooth SIG (https://www.bluetooth.org/en-us) under QD ID 54755. The Product Type is "Controller Subsystem", Specification Name is "3.0+HS". All four module variants (-SF1, -SF2, -DF1, -DF2) are listed as product variants under the above mentioned QD ID.

WiBear11n Data SheetVersion 1.20 Copyright © 2014 lesswire AG www.lesswire.com Page 20 of 20 Revision History Table 20: Revision history Date Version Author Description 20-Jun-2012 1.00 Igor Shevchenko Preliminary release 22-Jun-2012 1.01 Igor Shevchenko Andras Varadi Andreas Beierer Some minor mistakes fixed 16-Jul-2012 1.02 Igor Shevchenko PCM interface description added, Supported channels presented in region independent form. 01-Oct-2012 1.03 Igor Shevchenko Minor mistakes fixed, Evaluation Kit information added 05-Dec-2012 1.04 Daniel Dietterle Updated order codes for latest hardware revision C 11-Jan-2013 1.05 Daniel Dietterle Added installation and regulatory information 16-Jan-2013 1.06 Daniel Dietterle Added label information and table with FCC/IC IDs 18-Jan-2013 1.07 Igor Shevchenko Added Wi-Fi Direct mode support 18-Jan-2013 1.08 Igor Shevchenko Requirements (Note 2) for Sleep Mode updated 22-Jan-2013 1.09 Daniel Dietterle Added paragraph on IC compliance 06-Feb-2013 1.10 Daniel Dietterle Added paragraph on IC compliance in French language 22-Feb-2013 1.11 Igor Shevchenko Dimension drawing improved (tolerances added) 25-Feb-2013 1.12 Daniel Dietterle FCC ID's and IC ID's with cross-reference to model numbers 28-Mar-2013 1.13 Daniel Dietterle Added: RoHS compliance; mounting process (warpage); custom tariff numbers; IMDS number 07-May-2013 1.14 Daniel Dietterle Electrical specification updated: minimum supply voltage and ripple noise, digital pad ratings corrected Physical dimensions: Contour tolerances in corners of the PCB added 14-May-2013 1.15 Daniel Dietterle Added order information for tape&reel packing 15-May-2013 1.16 Daniel Dietterle Corrected ordering information for variants DF1 and SF2 (T&R) 21-May-2013 1.17 Daniel Dietterle Release, no changes. 19-Dec-2013 1.18 Daniel Dietterle Approved antenna list extended 13-Mar-2014 1.19 Daniel Dietterle Bluetooth QDID added, corrected several typos on page 3 10-Oct-2014 1.20 Daniel Dietterle Approved antenna list extended

Navigation menu