zBoost YX110 DUAL BAND BI-DIRECTIONAL SIGNAL BOOSTER User Manual USERS MANUAL

zBoost, LLC DUAL BAND BI-DIRECTIONAL SIGNAL BOOSTER USERS MANUAL

USERS MANUAL

5015 B.U. Bowman Drive Buford, GA 30518 USA Voice: 770-831-8048 Fax: 770-831-8598 Certification Exhibit FCC ID: S04YX110 IC ID: 5544A-YX110 FCC Rule Part: CFR 47 Part 22 Subpart H, Part 24 Subpart E IC Radio Standard Specification: RSS-131 ACS Report Number: 07-0255-LD Applicant: Wireless Extenders Inc. Model(s): YX110 Installation Guide
v0208ABOUT ZBOOST® FROM WI-EX®Wi-Ex® is the leader in cell phone signal boosters. zBoost® enhances the performance of your cell phone, smart-phone, PDA and wireless data card.Compatibility - Dual Band zBoosts® are compatible with all U.S. carriers regardless of technology(except iDEN, Nextel). Patent-pending technologies protect the Carrier Network.1-year manufacturer warranty -register at www.Wi-Ex.comzBoost® products have more awards, more sales and more locations than all other signal boosters ... COMBINED.Technical SpecicationszBoost zPocket YX110Frequency 1850 - 1990 MHz (1900 MHz) 824 - 894 MHz (800 MHz) Gain 26dB (1900 MHz) 31dB (800 MHz)Network Format CDMA, GSM, TDMA, GPRS, EDGE, 1xRTT, EVDO, HSDPACoverage distance from zBoost pocket is dependent upon headset or speaker range Wall Supply Input 100-240VAC; 60HzPower Consumption 1W standby, 3W max signalImput/Output Impedance 50 ΩBase Unit size/weight 4” x 5” x 1.3”/10 oz.Operating Conditions Indoors Use Only 5O to 40OC (40O to 105OF)FCC Certicated. Industry Canada Certied. Patents pending (including Network protection)Handles all protocols and includes multiple patent pending technologies to provide low-cost coverage while continually adapting to signals to prevent interference and remain transparent to the wireless network. Provides an indicator if the antennas are positioned improperly, but will NOT suer damage or interfere with the Carrier Network. zBoost zPocket YX110 1. Place the zBoost® base unit in a window or where you receive at least one bar. You must have some signal where you place the zBoost® base unit. It does not create signal.2. Plug the power supply into an outlet and connect the other end of the power supply to the zBoost® base unit.3. Place mobile device into the assembled pocket. Use your speaker, headset or Bluetooth device for mobility. Note: If red light appears during set up or any time during use, simply move the pocket further away from the base unit. * For questions, call 1-800-871-1612 or visit www.Wi-Ex.com .comMore zBoost products at www.Wi-Ex.comTHE ZBOOST® PRODUCT LINE - WHICH ZBOOST® IS RIGHT FOR YOU?For Your Home orOcezBoost for the Home and Oce boosts indoor cell coverage up to 2500 sq ft or up to 10,000 sq ft with optional accessoriesSupports multiple users simultaneouslyThree versions: YX500-CEL boosts 800 MHz* YX500-PCS boosts 1900 MHz or YX510 Dual Band boosts both 800 and 1900 MHz*For Your PersonalWorkspaceCreates a “Personal Cell Zone” for a single user - covers your workspaceGreat for Travel - Compact size, zero installation - take your Cell ZoneTM with you!Dual Band - (YX300) Works with all phones* and U.S. carriers, in-creasing signal strength for voice and dataCreate an in-vehicle Cell ZoneTM for a multiple users simultaneouslyExperience more miles of uninter-rupted service Dual Band - (YX230) Works with all phones* and carriers, increasing signal strength for voice and dataFor Your Car*except iDEN, Nextel © 2008, Wi-Ex. All rights reserved. EASY TO SET UP:PocketPPocketPower SupplyzBoostBase Unit
RF ExposureThis equipment complies with FCC radiaon exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 8” (20cm) between the pocket and your body. This transmier must not be co-located or operang in conjuncon with any other antenna or transmier. FCC InformaonFCC ID: SO4YX110Warning: Changes or modificaons to this device not expressly approved by Wi-Ex could void the user’s authority to operate the equipment.NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protecon against harmful interference in a residenal installaon. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instrucons, may cause harmful interference to radio communicaons. However, there is no guarantee that interference will not occur in a parcular installaon. If the equipment does cause harmful interference to radio or television recepon, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:• Reorient or relocate the receiving antenna.• Increase the separaon between the equipment and receiver.• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.• Consult the dealer or an experienced radio/TV technician for help.RF Exposure:The Manufacturer's rated output power of this equipment is for single carrier operaon. For situaons when mulple carrier signals are present, the rang would have to be reduced by 3.5 dB, especially where the output signal is re-radiated and can cause interference to adjacent band users. This power reducon is to be by means of input power or gain reducon and not by an aenuator at the output of the device.Industry Canada RegulaonsIC: 5544A-YX110This Class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulaons. Operaon is subject to the following two condions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operaon.The term “IC:” before the radio cerficaon number only signifies that Industry Canada technical specificaons were met.Cet appareillage numérique de la classe B répond à toutes les exigences de l’interférence canadienne causant des règlements d’équipement. L’opéraon est sujee aux deux condions suivantes: (1) ce disposif peut ne pas causer l’interférence nocive, et (2) ce disposif doit accepter n’importe quelle interférence reçue, y compris l’interférence qui peut causer l’opéraon peu désirée.Le terme "IC" avant que le nombre par radio de cerficaon signifie seulement que des caractérisques techniques du Canada d'industrie ont été rencontrées

Navigation menu