8devices JLP Broadband Digital Transmission System User Manual
8devices Broadband Digital Transmission System
8devices >
User manual
Jalapeno Data sheet Jalapeno is a very powerful quad-core CPU based module with dual band concurrent radio supporting 802.11ac Wave 2 technology Jalapeno is based on an IPQ4018 SoC from Qualcomm, which is extremely powerful quad core 700MHz CPU Cortex A7 CPU with NEON (high-performance media engine), ideal for routers, gateways and access points. It is a surface mountable, dual-sided, Wi-Fi enabled Linux module. It comes with a high-power (23 dBm per chain) dual-band concurrent radio supporting 802.11ac Wave2 technology (2x2 MiMo) reaching 1.167 Gbps data rate. USB 3.0, USB 2.0, I2S, UART, GPIO are the interfaces available on the module together with two Gigabit Ethernet ports. SoC has hardware NAT engine and high-end security features like crypto engine, secure boot and others. OpenWRT linux distribution source code is available on GitHub https://github.com/8devices and is supported by our growing community on http://www.8devices.com/community forum. Quick specs • 802.11 a/b/g/n/ac Wave 2, 2.4 and 5 GHz, 2x2 MIMO, 300 and 867 Mbps data rate, 23 dBm per chain output power • U.FL connectors for external antenna • 128 MB NAND and 8 MB NOR FLASH, 256 MB DDR3 RAM • Linux friendly , OpenWRT flash image and source code are available for download on www.8devices.com/wiki_jalapeno • CPU – IPQ 4018 (700 MHz quad core Cortex A7) • 23 dBm per chain output power dual-band concurrent radio with dedicated Tensilica CPU and 802.11ac Wave 2 support • 32 by 47 mm size • Surface mountable, dual-side design • Available interfaces - USB 2.0, USB 3.0, I2S, TDM, UART, GPIO, JTAG and 2 x 1000 Base-T Ethernet ports Block diagram +3.3V USB 3.0 USB 2.0 JALAPENO MODULE I2S TDM UART GPIO FRONT END JTAG RF ANT 0 DIPLEXER FRONT END DDR3 256MB MEMORY NAND 128MB MEMORY NOR 8MB MEMORY 1000 Base-T ETH0 1000 Base-T ETH1 IPQ4018 SOC FRONT END RF ANT 1 DIPLEXER FRONT END QCA8072 ETHERNET PHY Module dimensions Jalapeno Data sheet v1.2-18-2-20 Radio characteristics 2.4 GHz 802.11AC (20 MHz) 2.4 GHz 802.11AC (40 MHz) 5 GHz 802.11AC (20 MHz) 5 GHz 802.11AC (40 MHz) 5 GHz 802.11AC (80 MHz) Data rate (Mbps) 14.4 28.9 43.3 57.8 86.7 115.6 130.3 144.4 173.3 Sensitivity (dBm) -93 -90 -88 -85 80 -76 -74 -72 -68 Output power (dBm) 22 20 19 19 18 18 18 17 17 Data rate (Mbps) 30 60 90 120 180 240 270 300 360 400 Sensitivity (dBm) -90 -88 -85 -82 -77 -73 -73 -70 -66 -64 Output power (dBm) 21 19 18 18 18 18 17 17 17 17 Data rate (Mbps) 14.4 28.9 43.3 57.8 86.7 115.6 130.3 144.4 173.3 Sensitivity (dBm) -92 -89 -86 -83 -80 -76 -74 -73 -68 Output power (dBm) 22 20 19 19 18 18 18 17 17 Data rate (Mbps) 30 60 90 120 180 240 270 300 360 400 Sensitivity (dBm) -89 -86 -84 -81 -78 -73 -72 -70 -66 -67 Output power (dBm) 21 19 18 18 18 18 17 17 17 17 Data rate (Mbps) 65 130 195 260 390 520 585 650 780 866.7 Sensitivity (dBm) -86 -83 -80 -77 -74 -70 -69 -67 -63 -61 Output power (dBm) 21 19 18 18 18 18 17 17 17 17 Power consumption Scenario Voltage, V Current, A Power, W Idle without beacons 0.41 2.05 Idle with beacons 0.68 3.4 MCS0 HT20 2.55 12.75 MCS9 VHT80/HT40 (Highest rates) 1.78 8.9 Operating conditions The module can operate in a wide temperature range and different conditions depending on the enclosure. The following guidelines guarantee that it will work correctly. Parameter Units Min Max Working environment °C 55 Storage environment °C -40 70 Humidity %RH 10 90 Storage humidity %RH 90 Heatsink size recommendations It is essetial to use heatsink for the hardware designs based on Jalapeno module. Heatsink should be able to dissipate 7W and the recommended area is 175 cm2. It should be directly attached to the bottom side of Jalapeno module. Jalapeno Data sheet v1.2-18-2-20 70 69 68 67 66 65 64 63 62 61 60 59 58 57 ETH0_TRX3ETH0_TRX3+ ETH0_TRX2ETH0_TRX2+ ETH0_TRX1ETH0_TRX1+ ETH0_TRX0ETH0_TRX0+ ETH1_1000_LED ETH0_1000_LED ETH1_100_LED ETH0_100_LED GND 3.3V Module pinout Jalapeno 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 GND GND GND GND GND GND GND 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 GPIO_58 GPIO_63 UART_RX/ GPIO_60 UART_TX/ GPIO_61 GND GND ETH1_TRX0+ ETH1_TRX0ETH1_TRX1+ ETH1_TRX1ETH1_TRX2+ ETH1_TRX2ETH1_TRX3+ ETH1_TRX3GND USB2_DM USB2_DP GND USB3_SS_TX+ USB3_SS_TXGND USB3_SS_RX+ USB3_SS_RXGND USB3_HS_DM USB3_HS_DP GND 3.3V Data sheet v1.2-18-2-20 GND N.C. GND GND N.C. GND GND 3.3V N.C. GND RESET GND JTAG_TRST/ GPIO_5 JTAG_RST/ GPIO_4 JTAG_TDO/ GPIO_3 GND JTAG_TMS JTAG_TDI/ GPIO_0 JTAG_TCK/ GPIO_1 GND 3.3V Pin Name GPIO function select Configurable function Voltage (V) GND ETH1_TRX0+ AI, AO 1000 Base-T output positive ETH1_TRX0- AI, AO 1000 Base-T output negative ETH1_TRX1+ AI, AO 1000 Base-T output positive ETH1_TRX1- AI, AO 1000 Base-T output negative ETH1_TRX2+ AI, AO 1000 Base-T output positive ETH1_TRX2- AI, AO 1000 Base-T output negative ETH1_TRX3+ AI, AO 1000 Base-T output positive ETH1_TRX3- AI, AO 1000 Base-T output negative 10 GND 11 USB2_DM AI, AO USB 2.0 data negative 12 USB2_DP AI, AO USB 2.0 data positive 13 GND 14 USB3_SS_TX+ AO USB 3.0 SuperSpeed transmitter positive 15 USB3_SS_TX- AO USB 3.0 SuperSpeed transmitter negative 16 GND Ground connection 17 USB3_SS_RX+ AI USB 3.0 SuperSpeed receiver positive 18 USB3_SS_RX- AI USB 3.0 SuperSpeed receiver negative 19 GND Ground connection 20 USB3_HS_DM AI, AO USB 2.0 data negative 21 USB3_HS_DP AI, AO USB 2.0 data positive 22 GND Ground connection 23 3.3V PI 3.3V power supply 24 GPIO58 GPIO 3.3 LED[2] 3.3 smart_ant6 3.3 IO GPIO 3.3 Audio_txd[1] 3.3 Audio transmit data Audio_rxd 3.3 Audio receive data GPIO 3.3 blsp_uart0_rxd(1) 3.3 UART RX smart_ant4 3.3 IO LED[0] 3.3 audio_txbclk 3.3 IO Audio transmit bit block audio_rxbclk 3.3 IO Audio receive bit block GPIO 3.3 blsp_uart0_txd 3.3 UART TX smart_ant5 3.3 IO audio_txfsync 3.3 IO Audio transmit frame sync audio_rxfsync 3.3 IO Audio receiver frame sync LED[1] 3.3 boot_config(14) 3.3 25 26 27 GPIO63 UART_RX/GPIO60 UART_TX/GPIO61 Jalapeno Data sheet v1.2-18-2-20 Type Description Ground connection Ground connection Ground connection Pin Name GPIO function select Configurable function Voltage (V) 28 GND Ground connection 29 GND Ground connection 30 GND Ground connection 31 GND Ground connection 32 GND Ground connection 33 GND Ground connection 34 GND Ground connection 35 GND Ground connection 36 3.3V PI 3.3V power supply 37 GND Ground connection 38 JTAG_TCK/GPIO1 GPIO 3.3 JTAG_TCK 3.3 JTAG test clock GPIO 3.3 JTAG_TDI 3.3 JTAG test data in GPIO 3.3 JTAG_TMS 3.3 JTAG test mode state 39 40 JTAG_TDI/GPIO0 JTAG_TMS Type Description 41 GND Ground connection 42 JTAG_TDO/GPIO3 GPIO 3.3 JTAG_TDO 3.3 JTAG test data out boot_config(0) 3.3 GPIO 3.3 JTAG_RST_N 3.3 JTAG reset for debug GPIO 3.3 JTAG_ TRST_N 3.3 JTAG test reset Ground connection 0 - reset, 1 - run 43 44 JTAG_RST_N/GPIO4 JTAG_TRST_N/ GPIO5 45 GND 46 Reset Module reset 47 GND Ground connection 48 NC Not connected 49 3.3V PI 3.3V power supply 50 GND Ground connection 51 GND Ground connection 52 NC Not connected 53 GND Ground connection 54 GND Ground connection 55 NC Not connected 56 GND Ground connection 57 3.3V PI 3.3V power supply 58 GND Ground connection 59 ETH0_100_LED AO LED output for 100 Base-T activity 60 ETH1_100_LED AO LED output for 100 Base-T activity 61 ETH0_1000_LED AO LED output for 1000 Base-T activity 62 ETH1_1000_LED AO LED output for 1000 Base-T activity Jalapeno Data sheet v1.2-18-2-20 Pin Name GPIO function select Configurable function Voltage (V) Type 63 ETH0_TRX0+ AI, AO 1000 Base-T output positive 64 ETH0_TRX0- AI, AO 1000 Base-T output negative 65 ETH0_TRX1+ AI, AO 1000 Base-T output positive 66 ETH0_TRX1- AI, AO 1000 Base-T output negative 67 ETH0_TRX2+ AI, AO 1000 Base-T output positive 68 ETH0_TRX2- AI, AO 1000 Base-T output negative 69 ETH0_TRX3+ AI, AO 1000 Base-T output positive 70 ETH0_TRX3- AI, AO 1000 Base-T output negative PI - Power input I - digital input IO - digital bi-directional signal AO - analog output O - digital output AI - analog input Description Power supply It is recommended to use pin 23, 36, 49 and 57 to give power supply to the module. Power ratings Parameter 3.3V power supply Units Min Nominal Max 3.13 3.3 3.46 Digital I/O characteristics for 3.3V I/O Parameter Comments Min Max Units VIH High-level input voltage CMOS/ Schmitt 3.6 VIL Low-level input voltage CMOS/ Schmitt -0.3 0.4 VSHYS Schmitt hysteresis voltage – – mV IIH Input high leakage current 11, 2 No pulldown – μA IIL Input low leakage current 1, 2 No pullup -1 – μA IIHPD Input high leakage current 1, 3 With pulldown 10 60 μA IILPU Input low leakage current 2, 3 With pullup -60 -10 μA VOH High-level output voltage 4 CMOS, at pin-rated drive strength 3.0 3.6 VOL Low-level output voltage 4 CMOS, at pin-rated drive strength -0.3 0.4 IOZH Tri-state leakage current 1 Logic high output, no pulldown – μA IOZL Tri-state leakage current 2 Logic low output, no pullup -1 – μA IOZHPD Tri-state leakage current 1, 3 Logic high output with pulldown 10 60 μA IOZLPU Tri-state leakage current 2, 3 Logic low output with pullup -60 -10 μA CIN Input capacitance 5 – pF Software OpenWRT linux distribution source code is available on GitHub https://github.com/8devices and is supported by our growing community on http://www.8devices.com/community forum. Jalapeno Data sheet v1.2-18-2-20 31.8 28.9 28.65 4.9 3.15 2.9 46.90 45.45 39.5 5.95 3.45 1.45 PCB footprint Cut R3 .75 Detail A R0.6 1.2 35 25.5 1.9 2.9 10.9 16.9 Jalapeno Data sheet v1.2-18-2-20 R0.6 Detail B 1.4 1.2 Soldering paste footprint R0.74 1.15 2.35 Reflow profile recommendation Ramp up rate 3°C/second max Maximum time maintained above 217°C 120 seconds Peak temperature 250°C Maximum time within 5°C of peak temperature 20 seconds Ramp down rate 6°C/second max Reflow profile Temperature, C 250 200 150 100 50 Time Development kit 1 - 2 x 1000 Base-T Ethernet ports 2 - 2 x USB Type-A sockets (2.0 and 3.0) 3 - Mini USB Type-A socket (console + power) 4 - Buttons (reset and user - GPIO connected) 5 - External LEDs 6 - 2.45 mm pitch prototyping are holes 7 - Heatsink mounting screws 8 - Jalapeno module Jalapeno Data sheet v1.2-18-2-20 FCC Warning: If the FCC identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: “Contains Transmitter Module FCC ID: Z9W-JLP”, when the module is installed inside another device, the user manual of this device must contain below warning statements; 1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. This modular complies with FCC RF radiation exposure limits for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This modular must be installed and operated with a minimum distance of 20 cm between the radiator and user body. The device indoor use only for 5150MHz~5250MHz. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment IC Warning: This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device. Cet appareil est conforme aux CNR exemptes de licence d'Industrie Canada . Son fonctionnement est soumis aux deux conditions suivantes : ( 1 ) Ce dispositif ne peut causer d'interférences ; et ( 2 ) Ce dispositif doit accepter toute interférence , y compris les interférences qui peuvent causer un mauvais fonctionnement de l'appareil. This modular complies with IC RF radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. If the IC number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: “Contains IC: 11468A-JLP” when the module is installed inside another device, the user manual of this device must contain below warning statements; 1. This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device. 2. Cet appareil est conforme aux CNR exemptes de licence d'Industrie Canada . Son fonctionnement est soumis aux deux conditions suivantes : ( 1 ) Ce dispositif ne peut causer d'interférences ; et ( 2 ) Ce dispositif doit accepter toute interférence , y compris les interférences qui peuvent causer un mauvais fonctionnement de l'appareil. The devices must be installed and used in strict accordance with the manufacturer's instructions as described in the user documentation that comes with the product This modular complies with FCC RF radiation exposure limits for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This modular must be installed and operated with a minimum distance of 20 cm between the radiator and user body. The device indoor use only for 5150MHz~5250MHz. Approved antenna: Antenna Type: Antenna 0: Ceramic Antenna, Antenna 1: Omni Antenna Antenna gain: Antenna 0: 3dBi, Antenna 1: 10dBi Manufacture: TDK
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : No Create Date : 2018:09:04 16:32:16+08:00 Creator : Adobe Acrobat Pro 10.0.0 Modify Date : 2018:09:26 10:15:29-04:00 Title : Tagged PDF : Yes XMP Toolkit : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26 Metadata Date : 2018:09:26 10:15:29-04:00 Creator Tool : Adobe Acrobat Pro 10.0.0 Format : application/pdf Document ID : uuid:e1736d63-1944-4d82-8993-5e49aadee1c0 Instance ID : uuid:e27f031b-0a05-47af-812e-269377e66451 Producer : Adobe Acrobat Pro 10.0.0 Page Count : 11EXIF Metadata provided by EXIF.tools