Accton Technology VG2211I Personal Mobile Gateway User Manual VG2211I 38
Accton Technology Corp Personal Mobile Gateway VG2211I 38
Users Manual
VG007 Personal Mobile Gateway Installation Guide WA6102-ZZ Installation Guide Guide Personal Mobile Gateway VoIP Internet Gateway with IEEE 802.11b/g Wireless Access Point, IEEE 802.11b/g Wireless Client, IEEE 802.11b/g Wireless Repeater, and PSTN Telephony Functions VG007 E122005-R01 149100032900E Compliances Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio/TV technician for help FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. IMPORTANT NOTE:FCC Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters (8 inches) between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The antenna(s) used for this transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Industry Canada -Class B This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as set out in the interference-causing equipment standard entitled “Digital Apparatus,” ICES-003 of Industry Canada. Cet appareil numérique respecte les limites de bruits radioélectriques applicables aux appareils numériques de Classe B prescrites dans la norme sur le matérial brouilleur: “Appareils Numériques,” NMB-003 édictée par l’Industrie. EC Conformance Declaration Marking by the above symbol indicates compliance with the Essential Requirements of the R&TTE Directive of the European Union (1999/5/EC). This equipment meets the following conformance standards: • EN 60950 (IEC 60950) - Product Safety • EN 300 328 - Technical requirements for 2.4 GHz radio equipment • EN 301 489-1, EN 301 489-17 - EMC requirements for radio equipment This device is intended for use in the following European Community countries: • Austria • Belgium • Denmark • Finland • France • Germany • Italy • Luxembourg • Netherlands • Norway • Spain • Sweden • Switzerland • United Kingdom • Portugal • Greece • Ireland • Iceland Requirements for indoor vs. outdoor operation, license requirements and allowed channels of operation apply in some countries as described below: • In Italy the end-user must apply for a license from the national spectrum authority to operate this device outdoors. • In Belgium outdoor operation is only permitted using the 2.46 - 2.4835 GHz band: Channel 13. • In France outdoor operation is only permitted using the 2.4 - 2.454 GHz band: Channels 1 - 7. ii Contents Chapter 1: Introduction Package Checklist Hardware Description Component Description Chapter 2: Connecting the Personal Mobile Gateway 1-1 1-1 1-2 1-3 2-1 Internet Gateway Wireless Client Wireless Access Point Wireless Repeater VoIP Telephony Functions 2-1 2-2 2-3 2-5 2-7 Appendix A: Troubleshooting A-1 Diagnosing LED Indicators A-1 Appendix B: Cables and Pinouts Twisted-Pair Cable Assignments 10/100BASE-TX Pin Assignments Straight-Through Wiring Crossover Wiring RJ-11 Ports B-1 B-1 B-1 B-2 B-2 B-3 Appendix C: Specifications C-1 Physical Specifications Wireless Specifications VoIP Specifications Compliances C-1 C-2 C-2 C-3 iii Contents iv Chapter 1: Introduction The Personal Mobile Gateway is a compact multi-funtion network connection device. The unit provides secure wired and wireless high-speed data and VoIP (Voice over Internet Protocol) communications through an Internet connection. The Personal Mobile Gateway functions in the following operating modes: • Secure Internet Gateway • IEEE 802.11b/g Wireless Access Point • IEEE 802.11b/g Wireless Client • IEEE 802.11b/g Wireless Repeater The Personal Mobile Gateway’s capabilities make it ideal for business travelers or home users. The device provides a secure Internet gateway function between a cable/DSL modem connection and its wired LAN port and wireless clients. The integrated VoIP ability offers voice communications over the Internet from a wired or wireless connected PC, or by connecting a regular telephone set to its PHONE port. It can function as an 802.11b/g Wi-Fi access point providing a service to wireless clients. Or, it can function as a wireless client itself for PC connections to other Wi-Fi networks. In its wireless repeater mode, the Personal Mobile Gateway can extend the wireless range of other access points for greater flexibility when seeking a comfortable working location. In addition, the Personal Mobile Gateway can automatically select the operating mode based on its port connections, or it can be fully configured through an easy-to-use web-browser management interface. Package Checklist The Personal Mobile Gateway package includes: • One Personal Mobile Gateway • Two RJ-45 Category 5 network cables • One RJ-11 telephone cable • One Y-type USB power supply cable • One AC power adapter with detachable plug • Documentation CD (includes Installation Guide and Management Guide) Inform your dealer if there are any incorrect, missing or damaged parts. If possible, retain the carton, including the original packing materials. Use them again to repack the product in case there is a need to return it. 1-1 Introduction Hardware Description Top Panel Side Panels WAN Port LINE Port PHONE Port Factory Default Reset Button 1-2 Power Socket LAN Port Hardware Description Component Description WAN Port The Personal Mobile Gateway’s WAN port is a standard RJ-45 Ethernet network port. It is for connecting the gateway to an Internet connection device, such as an ADSL or cable modem, or to a switch in an Ethernet network that provides Internet access. The WAN port can be attached directly to your cable/DSL modem using one of the included Category 5 network cables. If you choose to use other, longer Category 5 network cables, be sure they conform to the specifications and pinouts provided in Appendix B. Note: The WAN port supports automatic MDI/MDI-X operation, which means you can use the same “straight-through” network cable for connection to a cable/DSL modem or Ethernet switch. LAN Port The Personal Mobile Gateway’s LAN port is a standard RJ-45 Ethernet network port that connects directly to your PC. It can also be connected to an Ethernet switch or hub to support more than one user. The LAN port can be attached directly to your PC using one of the included Category 5 network cables. If you choose to use other, longer Category 5 network cables, be sure they conform to the specifications and pinouts provided in Appendix B. Note: The LAN port supports automatic MDI/MDI-X operation, which means you can use the same “straight-through” network cable for connection to a PC or an Ethernet switch. PHONE Port The Personal Mobile Gateway’s PHONE port is a standard RJ-11 telephone port that connects directly to a standard (analog) telephone set. This allows a regular telephone to be used for making VoIP calls over the Internet. LINE Port The Personal Mobile Gateway’s LINE port is a standard RJ-11 telephone port that connects directly to a Public Switched Telephone Network (PSTN) jack. 1-3 Introduction LED Indicators The Personal Mobile Gateway includes three system status LED indicators and two port LED indicators for each of the LAN and WAN ports, as described in the following figures and tables. Power/Diag Internet Wireless LED Status Power/Diag On Green Indicates that the system is working normally. On Amber System running its power-on-self-test. If the LED remains on amber for more than 20 seconds, it indicates system errors. On Green Indicates the Personal Mobile Gateway has recieved an IP address from a DHCP server and can connect to the Internet. Off The Personal Mobile Gateway has no configured IP address to connect to the Internet. Slow Flashing Green Indicates a wireless association (connection) with a strong radio signal. Fast Flashing Green Indicates a wireless association (connection) with a weak radio signal. Off Indicates no wireless association (connection) or no radio signal Internet Wireless 1-4 Description Hardware Description Speed Link/Activity LED Status Description Right (Link/Activity) On Green Indicates a valid network link on the port. Flashing Green Indicates network activity on a port link. Left (Speed) Off There is no valid network link on the port. On Amber Indicates the port is operating at 100 Mbps. Off Indicates the port is operating at 10 Mbps. Factory Default Reset Button This button is used to reset the Personal Mobile Gateway to its factory default configuration. If you press and hold down the button for 5 seconds or more, any configuration changes you may have made are removed and the factory default configuration is restored. Power Connector The Personal Mobile Gateway does not have a power switch. It is powered on when connected to the AC power adapter, and the power adapter is connected to a power source. The power adapter automatically adjusts to any voltage between 100-240 volts at 50 or 60 Hz. No voltage range settings are required. The Personal Mobile Gateway can also be powered directly from a PC’s USB ports using the included Y-type USB power cable. The Personal Mobile Gateway requires two USB port connections to receive sufficient power. Radio Antenna The Personal Mobile Gateway includes an integrated internal antenna for wireless comunications. No external connections or adjustments are required. 1-5 Introduction 1-6 Chapter 2: Connecting the Personal Mobile Gateway In its default setting, the Personal Mobile Gateway’s operating mode is determined by how it is connected. The Internet gateway and wireless client modes are automatically implemented depending on the WAN port connection. The wireless access point and wireless repeater modes, as well as VoIP functions, require manual configuration using the Personal Mobile Gateway’s web management interface. The connections for each operating mode are described in the following sections. Internet Gateway Used as a gateway, the unit routes traffic between an Internet connected cable or ADSL modem, and wired or wireless PCs or notebooks. 3 Connect AC power Personal Mobile Gateway (Default IP 192.168.7.1) adapter to power source Connect WAN port to Cable/DSL modem Connect LAN port to PC Cable/DSL Modem Internet Notebook PC To connect the Personal Mobile Gateway for use as an Internet gateway, follow these steps: 1. Connect an Ethernet cable from the Personal Mobile Gateway’s WAN port to your Internet connected cable or ADSL modem. 2. Connect an Ethernet cable from the Personal Mobile Gateway’s LAN port to your PC. Alternatively, you can connect to a workgroup switch to support multiple users. The Personal Mobile Gateway can support up to 32 wired or wireless users. 2-1 Connecting the Personal Mobile Gateway 3. Power on the Personal Mobile Gateway by connecting the AC power adapter and plugging it into a power source. 4. Use your PC’s web browser to access the Personal Mobile Gateway’s management interface and run the Setup Wizard to make any configuration changes (refer to the Management Guide for details). The Personal Mobile Gateway has a default IP address of 192.168.7.1 and a subnet mask of 255.255.255.0. Note: If your PC has an IP address assigned by DHCP (Dynamic Host Configuration Protocol) or is set on the same subnet as the Personal Mobile Gateway (that is, the PC’s IP address starts 192.168.7.x), you can connect immediately to the web management interface. Otherwise, you must first change your PC’s IP address to be on the same subnet as the Personal Mobile Gateway. Wireless Client Used as a wireless client, the Personal Mobile Gateway can connect your PC to any nearby access point. Internet Access Point 2 Connect Y-type USB Personal Mobile Gateway (Default IP 192.168.7.1) power cable 1 Connect LAN port to PC to PC Notebook PC 2-2 Wireless Access Point To connect the Personal Mobile Gateway for use as a wireless client, follow these steps: 1. Connect an Ethernet cable from the Personal Mobile Gateway’s LAN port to your PC. 2. Power on the Personal Mobile Gateway by connecting the Y-type power cable to the unit and plugging the USB connectors into two of your PC’s USB ports. Alternatively, if you have access to a nearby power source, you can also power on the Personal Mobile Gateway by using the AC power adapter. 3. Use your PC’s web browser to access the Personal Mobile Gateway’s management interface and run the Setup Wizard to scan the area and select a specific access point for connection (refer to the Management Guide for details). The Personal Mobile Gateway has a default IP address of 192.168.7.1 and a subnet mask of 255.255.255.0. Note: If your PC has an IP address assigned by DHCP (Dynamic Host Configuration Protocol) or is set on the same subnet as the Personal Mobile Gateway (that is, the PC’s IP address starts 192.168.7.x), you can connect immediately to the web management interface. Otherwise, you must first change your PC’s IP address to be on the same subnet as the Personal Mobile Gateway. Wireless Access Point Used as a wireless access point, the Personal Mobile Gateway connects to an Ethernet LAN switch and extends the local network to associated wireless clients (PCs or notebooks with 802.11b/g wireless capability). From any nearby location, you can then make a wireless connection to the Personal Mobile Gateway and access the Ethernet network resources, including local servers and the Internet. 2-3 Connecting the Personal Mobile Gateway Notebook PC 2 Connect AC power Personal Mobile Gateway (Default IP 192.168.7.1) adapter to power source 1 Connect LAN port to Ethernet LAN switch Internet to web 3 Connect interface from LAN PC and use Setup Wizard to configure access point service Server Desktop PC To connect the Personal Mobile Gateway for use as an access point, follow these steps: 1. Connect an Ethernet cable from the Personal Mobile Gateway’s LAN port to your local network switch. 2. Power on the Personal Mobile Gateway by connecting the AC power adapter and plugging it into a power source. 3. From a PC on the local network, use a web browser to access the Personal Mobile Gateway’s user interface and run the Setup Wizard to configure the access point service (refer to the Management Guide for details). The Personal Mobile Gateway has a default IP address of 192.168.7.1 and a subnet mask of 255.255.255.0. If the default IP address is not compatible with the local network, you can first configure the Personal Mobile Gateway from a direct connection to a PC before installing the unit in the network. 2-4 Wireless Repeater Wireless Repeater The Personal Mobile Gateway can also operate in a wireless “repeater” mode to extend the range of other wireless access points. The unit forwards wireless traffic between wireless-enabled PCs and an access point. In repeater mode, the Personal Mobile Gateway does not forward wireless traffic to its LAN port. The LAN port can only be used for management access to the web interface. Note that when the unit operates in this mode, only half the normal wireless traffic throughput is possible. This is because the unit has to receive and then re-transmit all data on the same wireless channel. Internet Access Point 1 Connect AC power Personal Mobile Gateway (Default IP 192.168.7.1) adapter to power source Notebook PC Connect LAN port to PC to web 3 Connect interface and manually set repeater mode Notebook PC To connect the Personal Mobile Gateway for use as a wireless repeater, follow these steps: 1. Power on the Personal Mobile Gateway by connecting the AC power adapter and plugging it into a power source. 2. Connect an Ethernet cable from the Personal Mobile Gateway’s LAN port to your PC. 2-5 Connecting the Personal Mobile Gateway 3. Use your PC’s web browser to access the Personal Mobile Gateway’s management interface and manually set the unit to repeater mode (refer to the Management Guide for details). The Personal Mobile Gateway has a default IP address of 192.168.7.1 and a subnet mask of 255.255.255.0. Note: 4. 2-6 If your PC has an IP address assigned by DHCP (Dynamic Host Configuration Protocol) or is set on the same subnet as the Personal Mobile Gateway (that is, the PC’s IP address starts 192.168.7.x), you can connect immediately to the web management interface. Otherwise, you must first change your PC’s IP address to be on the same subnet as the Personal Mobile Gateway. When you have completed setting the Personal Mobile Gateway to repeater mode, you can remove the PC connection to the unit. VoIP Telephony Functions VoIP Telephony Functions The Personal Mobile Gateway can function as a VoIP gateway for making telephone calls over the Internet. Using the Internet to make VoIP calls to any other VoIP user in the world is essentially free, and even calls to regular PSTN (Public Switched Telephone Network) phones are much cheaper than making a traditional long distance calls. The Personal Mobile Gateway enables VoIP calls to be made using a regular (analog) telephone set, as well as a PC or VoIP phone. The regular telephone can also be used to make PSTN calls through the Personal Mobile Gateway. The Personal Mobile Gateway uses standard Session Initiation Protocol (SIP) technology to make VoIP calls. When you have connected the unit in either gateway, access point, wireless client, or repeater mode, use the web management interface to set up the SIP parameters. Refer to the Management Guide for more information on VoIP and SIP. Wireless VoIP Phone Notebook PC Personal Mobile Gateway (Default IP 192.168.7.1) 1 Connect LINE port to PSTN jack Cable/DSL Public Switched Telephione Network (PSTN) 2 Connect PHONE port Standard (Analog) Telephone to standard telephone Modem Internet 2-7 Connecting the Personal Mobile Gateway To connect the Personal Mobile Gateway to use its telephony functions, first connect and configure the Personal Mobile Gateway in the operating mode you want to use (see the appropriate section in this chapter.), then follow these steps: 1. Connect an RJ-11 telephone cable from the Personal Mobile Gateway’s PHONE port to your standard (analog) telephone set. 2. Connect an RJ-11 telephone cable from the Personal Mobile Gateway’s LINE port to an available PSTN telephone jack. 3. Use your PC’s web browser to access the Personal Mobile Gateway’s management interface and configure your VoIP and SIP settings (refer to the Management Guide for details). Note: 2-8 To make a PSTN call through the Personal Mobile Gateway, you must first dial “0” on the standard telephone set. The default on the PHONE port is for VoIP calls. Appendix A: Troubleshooting Diagnosing LED Indicators Troubleshooting Chart Symptom Action Power LED is Off • AC power adapter may be disconnected. Check connections between the Personal Mobile Gateway, the power adapter, and the wall outlet. Power LED is Amber for more than 20 seconds • The Personal Mobile Gateway has detected a system error. Reboot the Personal Mobile Gateway to try and clear the condition. • If the condition does not clear, contact your local dealer for assistance. WAN or LAN link LED is Off • Verify that the Personal Mobile Gateway and attached device are powered on. • Be sure the cable is plugged into both the Personal Mobile Gateway and corresponding device. • Verify that the proper cable type is used and its length does not exceed specified limits. • Check the cable connections for possible defects. Replace the defective cable if necessary. Note: For information on troubleshooting wireless connectivity issues, refer to the Management Guide. A-1 Troubleshooting A-2 Appendix B: Cables and Pinouts Twisted-Pair Cable Assignments For 10/100BASE-TX connections, a twisted-pair cable must have two pairs of wires. Each wire pair is identified by two different colors. For example, one wire might be green and the other, green with white stripes. Also, an RJ-45 connector must be attached to both ends of the cable. Caution: Each wire pair must be attached to the RJ-45 connectors in a specific orientation. (See “Straight-Through Wiring” on page B-2 and “Crossover Wiring” on page B-2 for an expADSL connectionation.) Caution: DO NOT plug a phone jack connector into the RJ-45 port. Use only twisted-pair cables with RJ-45 connectors that conform with FCC standards. The following figure illustrates how the pins on the RJ-45 connector are numbered. Be sure to hold the connectors in the same orientation when attaching the wires to the pins. 10/100BASE-TX Pin Assignments Use unshielded twisted-pair (UTP) or shielded twisted-pair (STP) cable for RJ-45 connections: 100-ohm Category 3 or better cable for 10 Mbps connections, or 100-ohm Category 5 or better cable for 100 Mbps connections. Also be sure that the length of any twisted-pair connection does not exceed 100 meters (328 feet). The RJ-45 port on the personal mobile gateway supports automatic MDI/MDI-X operation, so you can use straight-through or crossover cables for all network connections to PCs, switches, or hubs. In straight-through cable, pins 1, 2, 3, and 6, at one end of the cable, are connected straight through to pins 1, 2, 3, and 6 at the other end of the cable. B-1 Cables and Pinouts Table B-1. 10/100BASE-TX MDI and MDI-X Port Pinouts Pin MDI-X Signal Name MDI Signal Name Receive Data plus (RD+) Transmit Data plus (TD+) Receive Data minus (RD-) Transmit Data minus (TD-) Transmit Data plus (TD+) Receive Data plus (RD+) Transmit Data minus (TD-) Receive Data minus (RD-) 4,5,7,8 Not used Not used Note: The “+” and “-” signs represent the polarity of the wires that make up each wire pair. Straight-Through Wiring If the twisted-pair cable is to join two ports and only one of the ports has an internal crossover (MDI-X), the two pairs of wires must be straight-through. EIA/TIA 568B RJ-45 Wiring Standard 10/100BASE-TX Straight-through Cable White/Orange Stripe Orange End A White/Green Stripe Blue White/Blue Stripe Green White/Brown Stripe End B Brown Crossover Wiring If the twisted-pair cable is to join two ports and either both ports are labeled with an “X” (MDI-X) or neither port is labeled with an “X” (MDI), a crossover must be implemented in the wiring. EIA/TIA 568B RJ-45 Wiring Standard 10/100BASE-TX Crossover Cable White/Orange Stripe Orange End A White/Green Stripe Blue White/Blue Stripe Green White/Brown Stripe Brown B-2 End B RJ-11 Ports RJ-11 Ports Standard telephone RJ-11 connectors and cabling can be found in several common wiring patterns. These six-pin connectors can accommodate up to three wire pairs (three telephone lines), but usually only one or two pairs of conductor pins and wires are implemented. The RJ-11 ports on the side of the Personal Mobile Gateway contain only one wire pair on the inner pins (3 and 4). Red or Blue/White Green or White/Blue R T 123456 R = Ring Pin Signal Name T = Tip Wire Color Not used Not used Line 1 Ring Red or Blue/White Line 1 Tip Green or White/Blue Not used Not used B-3 Cables and Pinouts B-4 Appendix C: Specifications Physical Specifications Ports 2 10/100BASE-TX ports, RJ-45 connector, auto MDI/X 10BASE-T: RJ-45 (100-ohm, UTP cable; Category 3 or better) 100BASE-TX: RJ-45 (100-ohm, UTP cable; Category 5 or better) 1 FXS port (PHONE), RJ-11 connector 1 FXO port (LINE), RJ-11 connector LED Indicators Power, Internet, Wireless (802.11b/g Wireless Link/signal strength), WAN (Ethernet Link/Activity, Speed), LAN (Ethernet Link/Activity, Speed) AC Power Adapter Vendor: PHIH Model Number: PSC11R-050 Input: 100-240 VAC, 50-60 Hz Output: 5 VDC, 2A Unit Power Supply DC Input: 5 VDC, 1 A maximum Power Consumption: < 5 W Physical Size 105 x 78.67 x 24.7 mm (4.13 x 3.1 x 0.97 in) Weight 0.1 kg (0.22 lbs) Temperature Operating: -10 to 50 °C (14 to 122 °F) Storage: -40 to 70 °C (-40 to 158 °F) Humidity 5% to 95% (non-condensing) C-1 Specifications Wireless Specifications Maximum 802.11b/g Channels FCC/IC: 1-11 ETSI: 1-13 France: 10-13 Operating Frequency 2.4 ~ 2.4835 GHz (US, Canada, ETSI) Maximum Wireless Clients 32 Data Rate 802.11g: 6, 9, 11, 12, 18, 24, 36, 48, 54 Mbps (automatic fall back) 802.11b: 1, 2, 5.5, 11 Mbps (automatic fall back) Modulation Type 802.11g: CCK, BPSK, QPSK, OFDM 802.11b: CCK, BPSK, QPSK RF Output Power 802.11b: 18 dBm 802.11g: 14 dBm VoIP Specifications Voice Signaling Protocol SIP v2 Voice Codec G.711 G.726 G.729 a, b Voice Quality VAD (Voice Activity Detection) CNG (Comfortable Noise Generation) Echo cancellation (G.165/G.168 echo canceller) up to 16 milliseconds Adaptive jitter buffer, 70 to 200 milliseconds DTMF tone detection and generation Call progress generation Custom tone generation C-2 Compliances Call Features Call transfer Call waiting/hold/retrieve 3-way conference call Call-ID number and name Call-ID block Anonymous call blocking T.38 fax relay Dial plan (E.164 dialing plan) Do not disturb setting Speed dial Repeat dialing on busy Call return Call forwarding: No Answer/Busy/All Distinctive ringing Compliances Emissions FCC Part 15B Class B FCC ID grant IC RSS-210 IC ID grant EN 55022 Class B EN 55024 Radio Signal Certification FCC Part 15C 15.247, 15.207 EN 300-328 EN 301-489 Temperature IEC 68-2-14 Vibration IEC 68-2-36, IEC 68-2-6 Shock IEC 68-2-29 Drop IEC 68-2-32 C-3 Specifications Safety UL/cUL (UL 60950) EN 60950 (CB) TUV/GS Standards IEEE Std. 802.3-2002 10BASE-T and 100BASE-TX IEEE 802.11b, g Wi-Fi 11b/g, WPA UPnP C-4 Model Number: VG007 Pub. Number: 149100032900E, E122005-R01
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : No XMP Toolkit : 3.1-701 Modify Date : 2006:01:19 17:44:54+08:00 Create Date : 2006:01:09 14:46:12+08:00 Metadata Date : 2006:01:19 17:44:54+08:00 Creator Tool : FrameMaker 7.0 Format : application/pdf Title : VG2211I-38.book Creator : david Document ID : uuid:176661fd-5f3c-4e7c-a28c-22a95a923ad0 Instance ID : uuid:9e3713c5-f3fe-4199-b228-ea04f04b2e68 Producer : Acrobat Distiller 7.0.5 (Windows) Has XFA : No Page Count : 34 Author : davidEXIF Metadata provided by EXIF.tools