Cherry Europe AFIS5001 Autarker Funkschalter - Evaluation-Kit User Manual 6442008 01 US Funkschalter CD

Download:
Mirror Download [FCC.gov]
Document ID	1972772
Application ID	eMlX62u7xIRQdd8h9+e3mg==
Document Description	UserManual.pdf
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	19.29kB (241159 bits)
Date Submitted	2013-05-24 00:00:00
Date Available	2013-05-24 00:00:00
Creation Date	2012-12-03 20:36:11
Producing Software	Acrobat Distiller 9.5.2 (Windows)
Document Lastmod	2013-05-22 10:14:53
Document Title	6442008-01_US_Funkschalter_CD.fm
Document Creator	PScript5.dll Version 5.2.2
Document Author:	Kraft

Energy harvesting
wireless switch
Evaluation kit
Comfort/Engineer
Operating manual
6442008-01 US, Dez 2012
Safety guidelines
WARNING: Danger to life
• Do not install this kit as part of a safetyrelevant, life or health preserving facility.
CAUTION: Damage to components of
the evaluation kit due to electrical
discharge
• Observe the ESD protection.
CAUTION: Damage due to liquid in the
components of the evaluation kit
• Prevent liquid from getting inside the
components.
• Do not use solvents such as benzine or
alcohol, or scouring agent and scourers for
cleaning.
Contents
1 Area of application .............................................. 4
1.1 Comfort evaluation kit...................................... 5
1.2 Engineer evaluation kit .................................... 6
2 Product description ............................................ 7
2.1 Wireless switch ................................................ 7
2.2 Generator model .............................................. 7
2.3 Receiver ............................................................ 8
2.4 Software............................................................ 8
2.5 Antennas........................................................... 9
2.6 CD...................................................................... 9
3 Installing the USB driver .................................. 10
4 Installing software ............................................ 11
5 Troubleshooting ................................................ 13
6 Technical data................................................... 14
7 Engineer receiver interfaces ............................ 16
8 Declaration of conformity ................................. 19
9 Disposal............................................................. 19
10 Contact .............................................................. 19
11 General user information ................................. 20
1 Area of application
The evaluation kits were designed to show you the
main function and output of the energy harvesting
wireless switch.
The components provided are for testing purposes
and not suitable for using in a serial product, continuous operation or permanent connection to
other units.
1.1 Comfort evaluation kit
Volume model
generator
Wireless
switch
Receiver
stick
The Comfort evaluation kit receiver class 3 was
developed for convenient operation in a compact
design.
As only a small antenna is fitted due to its compact
design, the range is less than with an external
antenna.
The switch signals are displayed on the receiver
stick with LEDs. You can also see the strength of
the signals via software on a computer.
1.2 Engineer evaluation kit
USB cable
Wireless
switch
Volume
model
Receiver circuit board generator
SMD antenna
Dipol antenna
The engineer evaluation kit receiver class 2 is
designed for optimum output and consists of
several interfaces for the development
environment. It may only be operated by those with
electrical engineering expertise.
To gain direct access to the interfaces, the receiver
consists of a large circuit board without housing.
Several antennas can be connected to the SMA
connection on the circuit board.
See also: 7 "Engineer receiver interfaces".
You can also see the strength of the signals via the
software on a computer. These can be exported for
measuring.
2 Product description
2.1 Wireless switch
The switch contains a generator which converts the
mechanical energy of the probe into electrical
energy. The energy supplies the wireless
electronics and data is transmitted the with
868 MHz (Europe) or 915 MHz (US version).
2.2 Generator model
To show the small size of this part, the evaluation
kit contains a functionless volume model of the
generator.
2.3 Receiver
The radio signal is received by the antenna. The
electronics interpret the data and transmit the
information to the hardware and software
interfaces. The information is displayed via LEDs
and the software.
See also: 7 "Engineer receiver interfaces".
2.4 Software
The software on the computer displays the
following data:
Name
Value
Time stamp
Incoming time of the signal
UID
Switch ID
State
Switch status
Message
Signal received
Count
Number of signals received
Signal strength
Signal strengths received in
dBM and nW/pW
You can save up to 10 000 data sets. The data can
be deleted using the "Clear" button and saved as
*.txt files using the "Export" button. The
communication with individual switches and the
relay function can be deactivated.
2.5 Antennas
The Engineer evaluation kit contains 2 exchangeable antennas:
• SMD antenna circuit board with SMA connector
• SMA dipole antenna
2.6 CD
The CD contains demonstration software, CAD files
with the dimensions and these operating instructions.
3 Installing the USB driver
System requirements:
Windows XP, Vista or 7, USB 2.0 connection.
1 Copy the "Cherry_EHS-RF_Software" folder from
the CD onto your computer.
2 Connect the receiver.
• Comfort evaluation kit:
Plug the receiver stick into the computer so that
the components (LEDs) can be seen on the circuit board. Use a USB hub or an extension cable
if necessary.
• Engineer evaluation kit:
Connect the receiver circuit board to the computer using the USB cable provided.
The yellow LED flashes on the receiver.
The device driver installation prompts you to
install the driver software. The drivers for 32- and
64-bit variants are located in the "Cherry_EHSRF_Software/Driver" folder.
3 Follow the instructions in the installation wizard. If problems arise, you will find detailed video
instructions on the CD.
The yellow LED lights up on the receiver.
10
4 Press and hold down the button on the wireless
switch.
The green LED lights up.
5 Release the button again on the wireless switch.
The blue LED lights up.
4 Installing software
Requirement: The receiver is connected and the
USB driver is installed (see 3 "Installing the USB
driver"). The "Cherry_EHS-RF_Software" folder is
on your computer.
1 Link the "RadioMonitor.exe" file on your desktop
for later access.
2 Start the link to "RadioMonitor.exe".
If "dotNET Framework V4" is not installed on your
computer you will receive a message. Load
"dotNET Framework V4" from the CD and install
it.
The "Set_Check_COM" window appears.
3 Select the COM port of the receiver from the list.
(This is usually the one with the highest number.)
11
4 Press the wireless switch.
When you have selected the COM port of the
receiver, the switch position is shown on the
switch diagram.
The "Next >" button is active.
• If the button is not active:
Repeat the procedure by selecting another COM
port from the list until you have found the connection for the receiver.
5 Click on the Next >button.
The "RadioMonitor" window appears.
6 Press the switch.
The status of the switch is displayed by the switch
diagram, the two round areas and the status
display in the table. (Green = Status 0 = pressed.
Blue = Status 1 = released.)
12
5 Troubleshooting
• The yellow LED on the receiver is not flashing:
– Use another USB port on the computer/laptop.
• The reception is poor:
– Remove any metal objects from the transmission area.
– Do not place transmitters and receivers directly
on reflecting objects or walls.
– Switch off any possible sources of radio interference, such as electrical appliances or machines.
– Adjust the position of the antenna.
– Shorten the distance between transmitter and
receiver.
– Do not keep pressing the switch in quick succession.
• The same switching status is received several
times in a row (OO or 11):
– Do not keep pressing the switch in quick succession.
13
6 Technical data
Name
Value
Storage and operating temperature
0 °C ... +50 °C
Permissible relative
humidity
10 ... 90 %, noncondensing
Supply voltage
receiver
5.0 V/DC ±5 % SELV
Receiver current
consumption
Max. 100 mA
Receiver connection
to computer
USB 2.0, max. 3 m cable
Frequency
EU (AFIK-1xxx): 868 MHz
US (AFIK5xxx): 915 MHz
Modulation
FM
Transmission range
Open field: typ. 300 m,
in buildings: typ. 30 m
Transmitter power
level
At antenna connection:
10 dBm,
on the antenna:
max 9 dBm
14
Name
Value
Damping receiver
SMD circuit board
antenna: typ. 5 dB
SMA dipole antenna:
typ. 1 dB
Receiver signal-tonoise ratio
Min. 6 dB
Analog interfaces
0 ... 5 V (USB input voltage), 10 bit resolution,
max. output current 5 mA,
short-circuit protected
Digital interfaces
5 V TTL, max. continuous
current 5 mA, short-circuit protected
15
7 Engineer receiver
interfaces
햲
햴
햶
햵
햷
햳
햸
햹
햺
햽
16
햻
No.
Item Description*
햲
Analog 1: dimming
Analog 4: signal strength dBm
Digital 1: switch position
Digital 2: weak signal
Digital 3: interrupt for valid data
COM 1: interrupt for invalid data
햳
Relay, 12 V/DC, 1 A
COM
햴
Buzzer, 4 kHz
햵
Jumper set: buzzer on
햶
Analog 2: dimming inverted
Analog 3: reserved
LED: LED status
17
No.
Item Description*
Digital 4: dimmer pulse width modulation (PWM)
Digital 5: reserved
Digital 6: reserved
COM 2: interrupt for valid data (RF)
Supply voltage (VCC)
Earth (GND)
10
Digital 7: ATA
햷
LED red
햸
Status LEDs: blue, yellow, green
햹
USB port
햺
Antenna connection SMA
햻
Reset button
햽
Internal programming interface for
CHERRY
* You will find detailed comments on the CD.
18
8 Declaration of conformity
These components are CE certified
and comply with the EN 300-220
guidelines. They were made and
tested for use in Europe and USA in
accordance with the FCC Part 15.249 and 15B.
Observe the local regulations before using in other
countries.
9 Disposal
Dispose of the used components of the
evaluation kit at an official collection
point for electronic waste or at your
local dealer.
10 Contact
ZF Friedrichshafen AG
Electronic Systems
Cherrystraße
91275 Auerbach, Germany
Internet: www.cherryswitches.com
E-mail: info@cherryswitches.com
19
11 General user
information
We reserve the right to make technical modifications which serve the development of our products.
Improper use and storage can lead to faults and
damage to the product.
The warranty expires completely once unauthorized modifications to the product have been carried out. Do not carry out any unauthorized repairs
and do not open up the product. These instructions
are only valid for the supplied product.
The warranty for this product is for commercial
customers for one year from date of purchase. Liability for financial damages and defects is excluded.
20

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : Yes
Author                          : Kraft
Create Date                     : 2012:12:03 20:36:11+01:00
Modify Date                     : 2013:05:22 10:14:53+02:00
XMP Toolkit                     : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04
Producer                        : Acrobat Distiller 9.5.2 (Windows)
Creator Tool                    : PScript5.dll Version 5.2.2
Metadata Date                   : 2013:05:22 10:14:53+02:00
Format                          : application/pdf
Title                           : 6442008-01_US_Funkschalter_CD.fm
Creator                         : Kraft
Document ID                     : uuid:a5d11372-2f1d-4231-950b-3baaaf34250f
Instance ID                     : uuid:471970af-8d4f-476c-8146-a7c6e6109545
Page Count                      : 20

EXIF Metadata provided by EXIF.tools