HYUNDAI BS and C RMCU-COMPACT RMCU User Manual
HYUNDAI BS&C; Co.,Ltd RMCU
User Manual
RMCU MANUAL (Remote Machine Control Unit) 2017. 05 I. Overview Remote Machine Control Unit (RMCU) consists of 3G communication module, GPS, Controller Area Network (CAN), Powersupply device, and Microcontroller. The 3G module provides wcdma, gsm communication and carries the information of the vehicle to the external server. The CAN obtain information of the vehicle while communicating with each Electronic Control Unit (ECU). The Microcontrolle controls the entire RMCU. [RMCU] II. General Specifications 1.1 Rated Voltage and Operating Temperature 1) Operating voltage: 12/24 [VDC] 2) Operating temperature: -30 ~ + 85 ℃ 1.2 Detail Specification 1) Main power supply Name Function External constant power External input power power supply I/O Spec. Remarks 1) Main power supply 2) System Back-up Input 12/24VDC Leakage current: 10mA or less ON:9~28V ON:function start 1) System function start Input OFF:0~11V OFF:function end 12V or 24V Power 1) Internal rectified power 2) Regulator power supply 3) Communication terminal power supply Output 5V Power 1) Vcc power 2) Internal IC drive power 3) Antenna supply Power Output 5V ± 3% 3.3V Power 1) GPS board driving power Output 3.3V ± 3% 12V Input:9~15V 24V Input:20~32V 5V regulator Output voltage 3.3V regulator Output voltage 2) CPU AND MEMORY Name CPU CPU AND MEMORY Serial Flash ROM(Flash) EEPROM Function I/O Microcontroller 32bits, ARM Cortex-3 class Data memory Program memory Non volatile memory 4 Mbytes Spec. According to manufacturer's specifications 128Kbytes 8M Flash EEPROM Maintain recorded data even after power off 3) Wired communication Wired Name Function Serial(1) MCU comm. Serial(2) monitoring communication CAN Data communication I/O Spec. Data RS232 standard communication with equipment J1939 standard controller and firmware update 4) Mobile communication Name Description Coverage Mobile Frequency Remark WCDMA UMTS-FDD (Uplink / Downlink) Band I (1920~1980 / 2110~2170 MHz) Band II (1850~1910 / 1930~1990 MHz) Band V (824~849 / 869~894 MHz) Band VI (830~840 / 875~885 MHz) Band VIII (880~915 / 925~960 MHz) Uplink ≤5.76Mbps Downlink≤21Mbps GSM/EDGE (Uplink / Downlink) GSM850 (824.2~849.2 / 869.2~894.2 MHz) GSM900 (880~915 / 925~960 MHz) DCS1800 (1710.2~1784.8 / 1805.2~1879.8 MHz) PCS1900 (1850.2~1909.8 / 1930.2~1989.8 MHz) SIM Chip type Add. function GPS SMS / TCP / UDP / FTP GPS L1 Receiver(GPS + GNASS) Mobile Connector SIM(SMD Type) TNC (Silver) GPS SMA (Gold) Main 14 Pin III. Pin Map Description No. Name Description CAR_BATT1 Battery1 KEY_IGN Equipment IG MONITOR_TX [RMCU->PC] Monitoring (TX) MONITOR_RX [PC->RMCU] Monitoring (RX) GND GND GND GND CAN_S CAN communication(Shield) FW_EN F/W updated MTS_TX [RMCU->MCU] Monitoring (TX) 10 MTS_RX [MCU->RMCU] Monitoring (RX) 11 CAN_H CAN communication (High) 12 CAN_L CAN communication (Low) 13 GND GND 14 CAR_BATT2 Battery 2 IV. Description of Circuit 1. Power supply A. When power is applied, 5.3V DC DC Converter operates and + 5.3V_DCDC_SYS is output. B. + 5.3V_DCDC_SYS is input to 0.5A 3.3V LDO and outputs +3.3V_LIVE which corresponds to the power supply in the system. The previous circle is fed into a circuit that must always be operated. MCU, SPI FLASH and RESET IC. C. The + 3.3V_LIVE is then distributed to + 3.3V_FETOUT and + 3.3V_FETOUT_GPS by the FET Switch, which is fed to the peripheral peripheral circuits, ie the circuits that do not need to operate in Sleep mode, such as Analog Switch, UART Transceiver , CAN Transceiver & Controller, etc. + 3.3V_FETOUT_GPS is designed to supply power to and disconnect the GPS circuit. D. + 1.8V LDO is used for comparator input power for Ignition verification and RTC of Cellular MODEM circuit. E. + 5.0V_LDO is used for CAN transceiver IC. F. 2A 3.8V DC The DC CVT is used as a power source for Cellular modem. 2. Ignition A. When the vehicle is turned on, 9V or more is input to the IGN signal line. B. Check this and check the start on. If the start is on, the IGN_DET pin goes low. C. The basic operation principle of the circuit is determined by applying 1.8V to the comparator + with a comparative power supply and inputting the voltage divided by the resistor to the comparator. 3. CAN Communication A. CAN communication is operated by CAN Transceiver and CAN Controller. B. CAN Controller is implemented by SPI communication method. 4. UART communication A. Two UART communications are available: one for monitoring operation of the product and one for firmware update. B. These UARTs do not work in sleep mode. 5. Cellular Communication A. MODEM Module is used as peripheral circuit, and there is Level Shift to interface 1.8V I / O voltage of Micro SIM Socket and MODEM and 3.3V I / O voltage of MCU as peripheral circuits. B. The power source is + 3.8V_DCDC and the RTC power source is used by applying + 1.8V_LDO. C. The connector for connecting the external antenna is used with the TNC connector 6. GPS reception A. The GPS receiver IC uses UBLOX's 7Series. B. Supply + 3.3V to the outside to use Active Antenna. C. An analog switch is used to block unnecessary UART interrupts. D. The power supply uses + 3.3V_FETOUT_GPS. E. The connector for connecting to an external active antenna is SMA. 7. Serial NOR Flash A. It is memory for various NV data and FOTA. This Flash is connected to the constant power + 3.3V_LIVE V. Mechanical Drawings [Upper] [Lower]
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf Linearized : No Page Count : 7 Tagged PDF : No Language : ko-KR Page Layout : SinglePage XMP Toolkit : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39 PDF Version : 1.4 Producer : Hancom PDF 1.3.0.468 Creator Tool : Hancom PDF 1.3.0.468 Create Date : 2017:06:14 14:06:28+09:00 Modify Date : 2017:06:14 14:06:28+09:00 Metadata Date : 2017:06:14 14:06:28+09:00 Format : application/pdf Creator : KLA Title : Microsoft Word - RMCU Manual FCC인증용_SGS_ Date : 2017:06:14 14:06:28+09:00 Document ID : 1BC3DE89-9FF4-44F0-8214-3724DA491765 Instance ID : uuid:3EA0CB60-317A-4076-8C1C-5A4CA6BCF91F Part : 1 Conformance : B Author : KLAEXIF Metadata provided by EXIF.tools