Jiangmen Dascom Computer Peripherals TD12250 Dot Matrix Printer User Manual
Jiangmen Dascom Computer Peripherals Co.,Ltd. Dot Matrix Printer Users Manual
Users Manual
User Guide 1225 Matrix Printer Tally Dascom 1225 Important Safety Instructions (English) Read the following instructions thoroughly before starting up your printer. • Never carry out maintenance or repair work yourself. Always contact a qualified service technician. • Keep this Operator’s Manual in a place which is easily accessible at all times. • Place the printer on a solid and even base so that it cannot fall. • Never place the printer in the vicinity of inflammable gas or explosive substances. • Ensure the printer is connected to a socket with the correct mains voltage. • Always disconnect the printer from the mains before opening the device to perform maintenance work or remedy errors. • Do not expose the printer to high temperatures, direct sunlight or dust. • Keep all liquids away from the printer. • Protect the printer from shock, impact and vibration. • Make sure that the printer and computer are switched off before connecting the data cable. • The print head will become very hot during printing; avoid contact with the print head after printing has finished. • Do not perform any operation or action in any way other than those provided in this manual. When in doubt, contact your dealer or your customer support. Tally Dascom 1225 Wichtige Sicherheitshinweise (German) Lesen Sie bitte diese Sicherheitshinweise durch, bevor sie den Drucker in Betrieb nehmen. Führen Sie Wartungsarbeiten und Reparaturen keinesfalls selbst aus, sondern verständigen Sie immer einen qualifizierten Servicetechniker. Bewahren Sie diese Dokumentation an einem jederzeit zugänglichen Ort auf. Den Drucker auf stabilem und ebenem Untergrund so aufstellen, dass er nicht zu Boden fallen kann. Stellen Sie den Drucker keinesfalls in der Nähe von leicht entzündlichen Gasen oder explosiven Stoffen auf. Den Drucker nur an eine Steckdose mit der richtigen Spannung anschließen. Wenn Sie den Drucker vom Netz trennen wollen, den Drucker ausschalten und immer den Netzstecker an der Steckdose ziehen. Den Drucker weder hohen Temperaturen noch direktem Sonnenlicht und Staub aussetzen. Keine Flüssigkeiten mit dem Drucker in Berührung bringen. Den Drucker keinen Erschütterungen, Stößen oder Vibrationen aussetzen. Sicherstellen, dass der Drucker und der Computer ausgeschaltet sind, bevor das Datenkabel angeschlossen wird. Der Druckkopf wird während des Druckens heiß. Vor dem Berühren deshalb einige Zeit abkühlen lassen. Weichen Sie bei der Bedienung des Druckers nicht von den Anweisungen in der Dokumentation ab. Bei Unklarheiten wenden Sie sich bitte an Ihren Händler oder Ihren Kundendienst. II Tally Dascom 1225 Consignes importantes de sécurité (French) Lire attentivement les instructions suivantes avant de mettre l’imprimante en service. Ne jamais effectuer soi-même les travaux d’entretien et de réparations. Contacter toujours un dépanneur qualifié. Placer l’imprimante sur un support stable de façon à ce qu’elle ne puisse pas tomber. Ne jamais placer l’imprimante à proximité de sources de gaz aisément inflammables ou de substances explosives. Ne connecter l’imprimante à une prise que lorsque la tension est correcte. Pour déconnecter l’imprimante de l’alimentation principale, mettre l’imprimante hors tension et toujours débrancher le connecteur secteur de la prise murale. Ne pas exposer l’imprimante à des températures élevées, à la lumière directe du soleil ou à la poussière. Ne pas mettre l’imprimante en contact avec des liquides. Ne pas exposer l’imprimante à des chocs, impacts ou vibrations. S’assurer que l’imprimante et l’ordinateur sont hors tension avant de connecter le câble de données. La tête d’impression est brûlante pendant l’impression. C’est pourquoi laissez-la refroidir quelques instants avant d’y toucher. N'exécutez aucune opération ni action d'une autre manière que celle indiquée dans ce manuel. En cas de doute, veuillez contacter votre distributeur ou service après-vente. III Tally Dascom 1225 Indicazioni di sicurezza importanti (Italian) Prima di mettere in funzione la stampante, leggere attentamente le seguenti indicazioni. Non eseguire mai da sé gli interventi di manutenzione e riparazione, ma rivolgersi sempre a un tecnico di assistenza qualificato. Conservare le presenti istruzioni per l’uso in un luogo sempre accessibile. Collocare la stampante su una superficie stabile, per evitare che cada a terra. Non collocare la stampante in prossimità di gas facilmente infiammabili o di sostanze esplosive. Collegare la stampante a una presa di corrente con tensione adeguata. Per scollegare la stampante dalla rete di alimentazione, spegnere la stampante e disinserire sempre il connettore di rete dalla presa. Non esporre la stampante ad elevate temperature né alla luce solare diretta e alla polvere. Evitare il contatto della stampante con liquidi. Non esporre la stampante a colpi, scosse o vibrazioni. Verificare che la stampante e il computer siano spenti prima di collegare il cavo di trasmissione dati. Durante la stampa, la testina si surriscal-da notevolmente. Prima di toccarla, se necessario opportuno quindi lasciarla raffreddare qualche istante. Non eseguire alcuna operazione o azione se non nella maniera descritta nel presente manuale. In caso di dubbio, contattare il rivenditore o dalla società incaricata dell’assistenza. IV Tally Dascom 1225 Instrucciones de seguridad importantes (Spanish) Lea las siguientes instrucciones con esmero antes de poner la impresora en servicio. Nunca lleve a cabo trabajos de mantenimiento o reparación Ud. mismo, sino consulte a un técnico de servicio calificado. Guarde las presentes instrucciones de servicio en un lugar de fácil acceso en cualquier momento. Ponga la impresora sobre un base estable de manera que no pueda caer al suelo. Nunca coloque la impresora en la vecindad de gases de fácil inflamabilidad o sunstancias explosivas. Asegure conectar la impresora sólo a un enchufe con un voltaje correcto. Cuando quiera desconectar la impresora de la red, apague la impresora y siempre tire la clavija de alimentación del enchufe. No exponga la impresora a temperaturas altas, a la luz solar directa y al polvo. No ponga la impresora en contacto con fluidos. Nunca exponga la impresora a sacudidas, choques o vibraciones. Asegúrese de que la impresora y el ordenador estén apagdos antes de conectar el cable de datos. La cabeza de impresión se pone muy caliente durante la impresión. Por lo tanto, deje enfriarlo algún tiempo antes de tocarla. No permita que se realice cualquier operación o acción de una forma diferente a lo que se señala en el manual. En caso de duda, póngase en contacto con su comerciante o con su servicio post-venta. Tally Dascom 1225 ɉɪɚɜɢɥɚ ɩɨ ɬɟɯɧɢɤɟ ɛɟɡɨɩɚɫɧɨɫɬɢ. (Russian) ɉɪɨɱɢɬɚɣɬɟ, ɩɨɠɚɥɭɣɫɬɚ, ɢɧɫɬɪɭɤɰɢɸ ɩɨ ɬɟɯɧɢɤɟ ɛɟɡɨɩɚɫɧɨɫɬɢ ɩɟɪɟɞ ɜɤɥɸɱɟɧɢɟɦ ɜ ɪɚɛɨɬɭ ɩɪɢɧɬɟɪɚ. ɇɟ ɜɵɩɨɥɧɹɣɬɟ ɬɟɯɧɢɱɟɫɤɢɟ ɪɚɛɨɬɵ ɢ ɪɟɦɨɧɬ ɬɟɯɧɢɤɢ ɫɚɦɨɫɬɨɹɬɟɥɶɧɨ, ɧɨ ɫɨɨɛɳɚɣɬɟ ɨ ɧɟɢɫɩɪɚɜɧɨɫɬɹɯ ɤɜɚɥɢɮɢɰɢɪɨɜɚɧɧɵɦ ɫɟɪɜɢɫɧɵɦ ɬɟɯɧɢɤɚɦ. Ⱦɚɧɧɚɹ ɢɧɫɬɪɭɤɰɢɹ ɞɨɥɠɧɚ ɛɵɬɶ ɜɫɟɝɞɚ ɞɨɫɬɭɩɧɚ ɤɚɠɞɨɦɭ ɩɨɥɶɡɨɜɚɬɟɥɸ. ɍɫɬɚɧɨɜɢɬɟ ɩɪɢɧɬɟɪ ɧɚ ɪɨɜɧɨɦ ɢ ɫɬɚɛɢɥɶɧɨɦ ɦɟɫɬɟ ɬɚɤ, ɱɬɨɛɵ ɨɧ ɧɟ ɫɦɨɝ ɭɩɚɫɬɶ ɧɚ ɩɨɥ. ɇɢ ɜ ɤɨɟɦ ɫɥɭɱɚɟ ɧɟ ɫɬɚɜɶɬɟ ɩɪɢɧɬɟɪ ɜɛɥɢɡɢ ɥɟɝɤɨ ɜɨɫɩɥɚɦɟɧɹɸɳɢɯɫɹ ɝɚɡɨɜ ɢ ɜɡɪɵɜɱɚɬɵɯ ɜɟɳɟɫɬɜ. ȼɤɥɸɱɚɣɬɟ ɩɪɢɧɬɟɪ ɜ ɪɨɡɟɬɤɭ ɬɨɥɶɤɨ ɫ ɫɨɨɬɜɟɬɫɬɜɭɸɳɢɦ ɧɚɩɪɹɠɟɧɢɟɦ. ȿɫɥɢ ȼɵ ɯɨɬɢɬɟ ɨɬɤɥɸɱɢɬɶ ɩɪɢɧɬɟɪ ɨɬ ɧɚɩɪɹɠɟɧɢɹ, ɫɧɚɱɚɥɚ ɜɵɤɥɸɱɢɬɟ ɩɪɢɧɬɟɪ ɫɚɦ ɢ ɡɚɬɟɦ ɜɵɧɶɬɟ ɲɬɟɤɟɪ ɢɡ ɪɨɡɟɬɤɢ. Ȼɟɪɟɝɢɬɟ ɩɪɢɧɬɟɪ ɨɬ ɧɚɝɪɟɜɚɧɢɹ, ɨɬ ɩɨɩɚɞɚɧɢɹ ɧɚ ɧɟɝɨ ɩɪɹɦɵɯ ɫɨɥɧɟɱɧɵɯ ɥɭɱɟɣ ɢ ɩɵɥɢ. ɇɟ ɞɨɩɭɫɤɚɣɬɟ ɩɨɩɚɞɚɧɢɹ ɠɢɞɤɨɫɬɢ ɧɚ ɩɪɢɧɬɟɪ. ɇɟɥɶɡɹ ɩɨɞɜɟɪɝɚɬɶ ɩɪɢɧɬɟɪ ɬɪɹɫɤɟ, ɭɞɚɪɚɦ ɢ ɜɢɛɪɚɰɢɢ. ɍɛɟɞɢɬɟɫɶ, ɱɬɨ ɩɪɢɧɬɟɪ ɢ ɤɨɦɩɶɸɬɟɪ ɜɵɤɥɸɱɟɧɵ, ɬɨɥɶɤɨ ɩɨɫɥɟ ɷɬɨɝɨ ɫɨɟɞɢɧɢɬɟ ɩɪɢɧɬɟɪ ɫ ɤɨɦɩɶɸɬɟɪɨɦ. ɉɟɱɚɬɚɸɳɚɹ ɝɨɥɨɜɤɚ ɧɚɝɪɟɜɚɟɬɫɹ ɜɨ ɜɪɟɦɹ ɪɚɛɨɬɵ ɩɪɢɧɬɟɪɚ. ɉɨɷɬɨɦɭ ɩɨɞɨɠɞɢɬɟ ɤɚɤɨɟ-ɬɨ ɜɪɟɦɹ, ɩɪɟɠɞɟ ɱɟɦ ɞɨɬɪɨɧɭɬɶɫɹ ɞɨ ɧɟɟ. ɉɨɥɶɡɭɣɬɟɫɶ ɩɪɢɧɬɟɪɨɦ ɬɚɤ, ɤɚɤ ɷɬɨ ɧɚɩɢɫɚɧɨ ɜ ɞɨɤɭɦɟɧɬɚɰɢɢ. ȿɫɥɢ ɭ ȼɚɫ ɜɨɡɧɢɤɚɸɬ ɧɟɹɫɧɨɫɬɢ, ɨɛɪɚɳɚɣɬɟɫɶ ɫ ɜɨɩɪɨɫɚɦɢ ɤ ȼɚɲɢɦ ɩɪɨɞɚɜɰɚɦ ɢɥɢ ɜ ɫɟɪɜɢɫɧɵɣ ɰɟɧɬɪ. VI Tally Dascom 1225 Instruções Importantes sobre Segurança (Portuguese) Leia as instruções de segurança antes de usar a impressora. Consulte sempre um técnico qualificado para executar uma reparação . Coloque a impressora sobre uma base sólida e nivelada, para que ela não sofra quedas. Jamais instale a impressora nas proximidades de lugares onde haja gás inflamável ou substâncias explosivas. Assegure-se de conectar a impressora à tomada elétrica com a voltagem apro-priada. Quando desligar a impressora da rede, desligue sempre a impressora e retire o cabo da tomada. Não exponha a impressora a temperaturas altas ou luz solar direta. Não aproxime substâncias líquidas da impressora. Proteja a impressora de choques, impactos e vibrações. Desligue a impressora e o computador antes de conectar o cabo da rede. A cabeça da impressora pode ficar muito quente . Portanto, espere algum tempo antes de tocá-la. Não faça nenhuma operação ou ação além das recomendadas neste manual. Em caso de dúvida, contate seu revendedor ou companhia de serviço. VII Tally Dascom 1225 Önemli Güvenlik Talimatları (Turkish) Lütfen, yazıcıyı iúletime geçirmeden önce bu güvenlik talimatlarını bütünüyle dikkatle okuyun. Bakım ve tamir çalıúmalarını kesinlikle ve hiçbir surette kendi baúınıza yapmayın; her zaman kalifiye bir uzman servis-teknisyenine haber verin. Yazıcıyı, üzerinden yere düúmesi mümkün olmayacak sabit ve düz bir zemine yerleútirin. Yazıcıyı kesinlikle ve hiçbir surette kolayca yanabilecek gaz veya patlayıcı maddeler içeren nesnelerin yakınına koymayın. Yazıcı akım kablosunu sadece do÷ru gerilime sahip bir prize takın. Yazıcıyı úebeke a÷ından ayırmak istedi÷inizde, yazıcıyı kapatın ve a÷-fiúini her zaman prizden çıkartın. Yazıcıyı ne yüksek ısılı ne de do÷rudan güneú ıúı÷ına ve toza mâruz kalan mekânlarda bulundurun. Yazıcı hiçbir sıvı maddeyle temasta olmamalıdır. Yazıcı hiçbir sarsıntıya, darbeye veya titreúime mâruz kalmamalıdır. Veri kablosu ba÷lanmadan önce hem yazıcının hem de bilgisayarın kapalı olduklarından emin olmalısınız. Yazıcının baúı basma esnasında yüksek ısıya ulaúıyor. Bu yüzden lütfen dokunmadan önce kısa süre so÷umasını bekleyin. Yazıcının iúletimi ve kullanımında bu dokümantasyondaki talimatların hiç dıúına çıkmayın. Sorunlu görünen hususlarda lütfen imâlatçınıza veya müúteri hizmetleri servisinize baúvurun. VIII Tally Dascom 1225 TRADEMARK ACKNOWLEDGEMENTS “IBM” is a trademark of International Business Machines Corporation. “EPSON” is a trademark of Epson America Incorporated. “DEC” is a trademark of Digital Equipment Corporation. “Centronics” is a trademark of Centronics Data Computer Corporation. “DOS” is a trademark of Microsoft Corporation. “SAP” is a trademark of SAP AG. “Windows”, “Windows 7”, “Windows 95”, “Windows 98“, “Windows NT”, “Windows 2000”, “Windows 2003/2008 Server”, “Windows XP” and “Windows Vista” are trademarks of Microsoft Corporation. All other product names and company names appearing in this manual are the registered trademarks or trademarks of the individual companies. IX Tally Dascom 1225 Tally Dascom 1225 TABLE OF CONTENTS 1 UNPACKING GUIDE ........................................................................................................................................ 1 PLACING THE PRINTER ........................................................................................................................................ 2 PRINTER COMPONENTS ...................................................................................................................................... 2 2 SETTING UP PRINTER.................................................................................................................................... 4 INSTALL RIBBON.................................................................................................................................................. 4 INSTALL THE SINGLE SHEET FEEDER....................................................................................................................5 CONNECTING THE INTERFACE CABLE ...................................................................................................................5 CONNECTING THE MAINS POWER ........................................................................................................................6 INSTALLING THE WINDOWS DRIVER ......................................................................................................................7 3 PAPER INSTALLATION GUIDE.................................................................................................................... 10 ADJUSTING THE PRINT GAP LEVER ....................................................................................................................10 FRICTION FEED HANDLING ................................................................................................................................ 10 TRACTOR FEED HANDLING ................................................................................................................................ 11 CONTINUOUS PAPER PLACEMENT ......................................................................................................................12 4 CONTROL PANEL OPERATION................................................................................................................... 13 PANEL OPERATION ............................................................................................................................................ 15 Online State............................................................................................................................................................. 16 Offline State ............................................................................................................................................................ 17 Power-On State ...................................................................................................................................................... 19 LANGUAGE SETUP ............................................................................................................................................ 20 5. PRINTER SETTING CHANGES.................................................................................................................... 21 SYSTEM SETUP ................................................................................................................................................ 21 PRINT SETUP.................................................................................................................................................... 21 PAGE SETUP .................................................................................................................................................... 23 INTERFACE SETUP ............................................................................................................................................ 24 ADVANCED SETUP ............................................................................................................................................ 24 VERTICAL ALIGNMENT ....................................................................................................................................... 34 CHANGE PIN FUNCTION .................................................................................................................................... 35 ADJUST PHYSICAL MARGINS .............................................................................................................................36 DASCOM PRINTER SETUP TOOL ........................................................................................................................38 6 MAINTENANCE.............................................................................................................................................. 39 CLEANING AND VACUUMING THE PRINTER ..........................................................................................................39 CLEANING THE PAPER ROLLERS ........................................................................................................................39 7 TROUBLESHOOTING.................................................................................................................................... 41 PRINT QUALITY PROBLEMS AND SOLUTIONS .......................................................................................................41 PAPER HANDLING PROBLEMS AND SOLUTIONS ...................................................................................................42 OPERATING PROBLEMS AND SOLUTIONS ............................................................................................................42 XI Tally Dascom 1225 ERROR INDICATIONS ON LEDS ..........................................................................................................................43 DIAGNOSTIC FUNCTIONS ................................................................................................................................... 44 FIRMWARE UPDATE ........................................................................................................................................... 45 8 GENERAL SPECIFICATIONS ....................................................................................................................... 46 9 INTERFACES ................................................................................................................................................. 51 PARALLEL INTERFACE........................................................................................................................................ 51 USB INTERFACE ............................................................................................................................................... 51 10 CHARACTER SETS & CODE PAGES ........................................................................................................ 52 CHARACTER SETS ............................................................................................................................................ 52 INTERNATIONAL CHARACTER SETS .....................................................................................................................54 INTERNATIONAL CHARACTER SET COMMANDS ....................................................................................................54 CHARACTER TABLES ......................................................................................................................................... 55 CODE PAGE COMMANDS ................................................................................................................................... 57 CODE PAGE TABLES.......................................................................................................................................... 59 11 CONTROL CODES SUMMARY................................................................................................................... 83 EPSON EMULATION COMMAND LIST ...................................................................................................................83 IBM EMULATION COMMAND LIST .......................................................................................................................85 FCC STATEMENT............................................................................................................................................. 87 XII Tally Dascom 1225 1 Unpacking Guide Place your packaged printer on a solid base. Make sure that the “Up” symbols point in the correct direction. Open the packaging, lift the printer out of the cardboard box and remove the remaining packaging material. Check the printer for any visible transport damage and missing items. If you find any transport damage or if any accessories are missing, please contact your dealer. The following items should be included: Printer Paper feed knob Paper feed tray Power cord Ribbon cartridge CD-ROM Installation Guide Remove the packaging materials from the printer as follows: 1. Remove the tape on the paper feed lever. 2. Remove other visible tape on the printer. 3. Open and remove the top cover of the printer. 4. Remove the shipping cardboard from around the print head. 5. On the left and right sides, remove the protective foam inserts. 6. Install the paper feed knob. Tally Dascom 1225 Placing the Printer Place the printer on a solid, flat, stable surface; ensuring that the printer is positioned in such a way that it cannot move, and that there is easy access to the control panel and paper input devices. Also ensure that there is enough space for sufficient ventilation and for the printed output. When selecting the printer location, observe the following additional instructions: Never place the printer near to any flammable gas or explosive substances. Do not expose the printer to direct sunlight. If you cannot avoid placing the printer near a window, protect it from the sunlight with a curtain. When connecting a computer to the printer, make sure the maximum recommended cable length is not exceeded. Ensure sufficient distance between the printer and any heating devices/radiators. Avoid exposing the printer to extreme temperature or air humidity fluctuations. Avoid exposure to dusty environments. It is recommended the printer is installed in a position which reduces noise exposure to the work place during printing. The socket-outlet shall be installed near the equipment and shall be easily accessible. Printer Components Tally Dascom 1225 Component Gap Lever Function Controls printing impact or density. Adjusts the print gap lever according to the thickness of paper. Paper Guides Adjusts positioning of single sheet paper. Print Head 24-pin printing mechanism Cover Protects print head and other components inside, and reduce noise. Control Panel Shows printer status, for printer setup. Paper Feed Lever Two positions: Paper Feed Knob Manual feed or vertical positioning of paper Power Switch Power printer ON or OFF Ribbon Cartridge Install ribbon in the printer. Ribbon Frame For guiding ribbon installation on print head. Tractors For feeding and adjustment of continuous forms. Power Receptacle Connects power cord to the printer. Interface Connects interface cables from the host. = continuous forms; = single sheet paper Tally Dascom 1225 2 Setting Up Printer Install Ribbon 1. Ensure the power to the printer is off and the print gap lever “A” is set to the furthest open position. Move the carriage to the centre of the print platen. 2. Install the recess positions c on the ribbon cassette into the printer mounting. 3. Press the ribbon frame d onto the print head. 4. Turn the ribbon knob e in clockwise direction until the ribbon fabric is taut. Move the carriage left and right to ensure the carriage and ribbon fabric can move smoothly. 5. Ensure the print gap lever “A” is set to the original position. 6. Close the printer’s top cover. When printer is in operation, ensure the printer’s top cover is closed to keep the noise level to a minimum. Notes on Ribbon Cartridge Removal: 1. 2. 3. 4. 5. 6. Eject any paper loaded in the printer. Turn off the printer power. Open and remove the top cover. Lift up the tear bar. Set the gap lever to the most open position labeled “RIBBON”. Move the carriage to the middle. Be careful not to touch the print head if printing had just been performed, as the print head may be hot. 7. Remove the blue ribbon frame from the print head. 8. Use fingers to take hold of the handle on the ribbon cartridge firmly, and lift the cartridge upwards to unlatch it. Some force may be needed to unlatch the cartridge. Tally Dascom 1225 Install the Single Sheet Feeder Install the single sheet feeder into the rear of the printer. Connecting the Interface Cable The 36-pin Centronics parallel and USB ports are located at the rear of the printer. IMPORTANT: Make sure the printer and the computer are switched off before connecting or disconnecting the interface cable to prevent electrical damage to the interface ports. Tally Dascom 1225 Connecting the Mains Power Checking the printer voltage Make sure that the device has been set according to your country’s power supply voltage. To do this, check the rating plate at the back of the printer. Contact your dealer if the setting is incorrect. Never switch on the printer if the voltage setting is incorrect; this may result in electrical damage to the printer. Make sure that the power switch “A”, located to the right side of the printer, is in the “O” (off) position. Connect the power cord to the power inlet of the printer. Connect the power cord plug to a mains socket. Switch on the printer. Tally Dascom 1225 Installing the Windows Driver (Windows 2000/2003/2008 Server/XP/Vista/7) 1. Your printer CDROM comes with Windows drivers. Go to the Drivers folder and run the Installer “DriverSetup.exe”. You will see the screen on the right. Click “Next” to continue. 2. A list of ports available on your system will be displayed as shown on the right. Choose the desired port to use. Click “Next” to continue. 3. Select the desired printer model as shown on the right. Click “Next” to continue. Tally Dascom 1225 4. Here you can choose whether to set the driver as the system default driver, and whether you want to print the Test Page after installation is completed. If the driver had been installed before, it would be listed in the white box on the right. Select the listed driver (if any) if you want to replace it; otherwise a copy of the driver will be installed. Click “Next” to continue. 5. Click “Finish” to start the installation process. 6. If the driver is not yet Microsoft Certified, the message on the right would appear. Anyway”. (As Click we “Continue continue to expand our product portfolio, not all of our drivers may be certified yet. Please check our website www.dascom.com for the latest certified drivers.) Tally Dascom 1225 7. Installation in progress. 8. After installation is completed successfully, you will see the message on the right. Tally Dascom 1225 3 Paper Installation Guide The printer can handle either single sheets or continuous forms. Single sheets, also called cut sheets, include envelopes and non-continuous, multipart forms. Continuous forms include labels and multipart forms fed into the printer using the forms tractors. The printer is able to print 1~5 plies multipart paper. Do not load paper that has been folded or is damaged, wrinkled, or curled. Adjusting the Print Gap Lever The print gap lever is on the left side of the printer. Take care to adjust the print gap lever to a suitable position whenever you change the number of copies being printed. Using the wrong print gap may cause print head damage or paper jams. Weight (g/m2) / ply Thickness (mm) 52̚100 0.06̚0.12 2-ply 40̚52 0.12̚0.14 3-ply 40̚52 0.17̚0.22 4-ply 40̚52 0.23̚0.27 5-ply 40̚52 0.28̚0.33 Change ribbon --- Above 0.45 Paper type Single sheet There are 2 paper feed modes: friction feed and tractor feed. Friction Feed Handling 1. Move the paper-feed lever forward to “ ” for friction feed mode. 2. Adjust the print gap lever if necessary. 10 Gap lever position 1PЊ2P 3PЊ4P 5P Tally Dascom 1225 3. Raise the single sheet feeder until it locks into its mounting. Align the left paper guide with the mark on the left of the single sheet feeder. Adjust the right paper guide to the width of the paper used. 4. Insert a sheet of paper. Make sure that the bottom edge of the paper engages snugly with the platen. 5. The paper should advance automatically to the print position. The printer is now ready to print in the online state. Paper Guides Tractor Feed Handling 1. Move the paper-feed lever backward to “ ” for continuous paper position. 2. Adjust the print gap lever if necessary. 3. Raise the tractor doors and fit the first 3 paper holes onto the left tractor pins. Close the left tractor door. In the same way, install the paper on the right tractor. 4. Adjust the right tractor to the width of the paper until the paper is flat. Do not stretch the paper too taut. Push the right lock lever down to secure the right tractor in place. 5. Press theǏLoad/Ejectǐkey to load the paper to the starting print position. The printer is now ready to print in the online state. 11 Tally Dascom 1225 Continuous Paper Placement 1. Place the printer on a solid base. The minimum suitable height of the solid base is 75 cm. 2. Left and right positioning: The direction of continuous paper should be parallel with the paper guide. The tolerance should be less than 3 cm. 3. Front and back positioning: The distance between the rear of printer and the wall should be more than 60 cm. To avoid paper jam, the distance between the continuous paper and the edge of desk should be 10~15 cm. 12 Tally Dascom 1225 4 Control Panel Operation There are 5 switches S1~S5 and 10 LEDs L1~L10. The meaning and application of each switch and LED are described below. LED Indicators “Power/Paper Out” LED: On: Power on Flashing: Paper out Flashing + buzzer: Paper jam “Online” LED: On: The printer is in online state and ready to receive data from the computer. Off: The printer is in offline state and cannot receive data. “Pitch” LEDs: On: Indicates the selected pitch. “Font” LEDs: On: Indicates the selected font. Control Panel Keys “Online” Key: This key switches the printer between online and offline states. Printing is stopped when the printer is switched to offline state. When printer is switched to online state again, printing will resume. “Load/Eject” Key: When paper is loaded, pressing this key will eject the paper (single sheet mode) or park the paper (continuous paper mode). When paper is not loaded, pressing this key will load the paper to the starting print position. 13 Tally Dascom 1225 “LF/FF” Key: Pressing this key will feed paper one line forward. By holding down this key, the printer will initially feed a few lines, then perform a form feed (continuous paper mode) or eject the form (single sheet mode). “Tear Off” Key: When online, this key will move any loaded continuous paper to the tear-off position. When offline, this key is used to select the desired pitch. “Font” Key: When offline, this key is used to select the desired font. Table 4.1 Switch Top Label Bottom Label S1 Font Clear/Reset S2 Tear Off Pitch S3 LF/FF Micro Feed Down S4 Load/Eject Micro Feed Up S5 Online Table 4.2 LED Function L1 Draft L2 Sans Serif L3 Prestige L4 Others L1, L2 Roman L2, L3 Courier L3, L4 Script L5 10CPI / Tear Off L6 15CPI L7 20CPI L8 PS L5, L6 12CPI L6, L7 17CPI L9 Power/Paper Out L10 Online 14 Tally Dascom 1225 Panel Operation There are 3 states of operation: Online, Offline and Power On. In the Online state, the keys provide the following functions: Go to Tear Off position, Line Feed/Form feed, Load/Eject, and switch to Offline state. In the Offine state, the keys provide the following functions: Font select, Pitch select, Line Feed/Form feed, Load/Eject, and switch to Online state, micro feed, control PE (paper error) sensitivity, clear buffer and restore factory defaults. To enter the Power On state, the user holds down a key or a combination of keys while powering up the printer. This state provides the following functions: Main Menu setup, Hex-dump, print Main Menu, access Service Menu, adjust page margins, restore factory defaults, and firmware update. The followings describe the 3 states in details. Legend: [A] = press and hold switch A {B} = press and then release switch B [A]+ {B} = press switch B while holding A 15 Tally Dascom 1225 Online State Function Name Online Switch Operation {S5} LED L10 Function Description Toggles between Online and Offline states x Load: Automatically loads the paper (according to path selection) when no paper is on the platen. Load/Eject {S4} x Eject: For rear tractor, it retracts the form from the platen to allow users to install cut sheets. (NOTE: Users have to toggle the path selection lever.) For cut sheets, it ejects the form on the platen. LF {S3} Feeds a line with every press of S3. By holding S3, the printer initially feeds a few lines; then FF [S3] feeds the form to the next TOF for rear tractor or ejects the form for cut sheets. This is valid for tractor mode only. It feeds the form to the tear-off position. After tearing off the form, printing starts Tear Off {S2} L5 flashing on the next TOF by: x pressing S2 once, or x receiving print data from the host. 16 Tally Dascom 1225 Offline State Function Name Switch Operation LED Function Description Font {S1} L1~L4 Selects the font. Pitch {S2} L5~L8 Selects the pitch. LF {S3} Feeds a line with every press of S3. By holding S3, the printer initially feeds a few lines; then feeds FF [S3] the form to the next TOF for rear tractor or ejects the form for cut sheets. x Load: Automatically loads the paper (according to path selection) when no paper is on the platen. Load/Eject {S4} x Eject: For rear tractor, it retracts the form from the platen to allow users to install cut sheets. (NOTE: Users have to toggle the path selection lever.) For cut sheets, it ejects the form on the platen. Online {S5} L10 Toggles between Online and Offline states Micro Forward {S4}+[S5] While holding down S5, press S4 to micro feed paper up. Micro Reverse {S3}+[S5] While holding down S5, press S3 to micro feed paper down. Activate [S2]+{S3} Activates the calibrated PE sensor sensitivity value according user-defined to the currently selected paper path. Beeps once when sensitivity completed. 17 Tally Dascom 1225 Calibrate PE {S1}+[S2] sensor x Out-of-paper: Beeps once. Automatically loads a form in 10 seconds. x Paper loaded: Calibrates PE sensor with paper loaded and sensitivity save the sensitivity value. Beeps 5 times when completed. x [NOTE: There are 2 independent sensors for rear tractor and front friction. Restore default [S2]+{S4} Resets PE sensor sensitivity to factory defaults. Beeps twice PE sensor when completed. sensitivity Clear Buffer and Reset {S1}+[S5] x Clears the print buffer. Beeps once upon completion. x Pressing S1 longer initializes the printer to default settings. Beeps 3 times upon completion. 18 Tally Dascom 1225 Power-On State Function Switch Name Operation Menu Setup / [S2] LED EDS Function Description Allows for Main Menu setting changes. Please read the instructions printed on how to change settings when this mode is activated. (EDS: Electronic DIP Switch) Hex Dump [S4] Beeps once to indicate going into hex dump mode: x Prints data from host in hexadecimal representation. x Pressing S4 suspends the printing. x When the hex dump has finished, pressing S4 forces the printing of the last line of data, as any line termination control code from host has no function. x Pressing S1 can change the font. x Switch off the power to terminate the hex dump. Self Test / [S5] Status Page Service Menu Prints the printer settings and self-test pattern. Pressing S1 can change the font. [S2]+[S3] Vertical Alignment, Change Pin Function and Endless Self Test Adjust Page Margins [S4]+[S5] Includes Adjust Fanfold Top Margin, Adjust Single Top Margin, Adjust Fanfold Left Margin, Adjust Single Left Margin and Adjust Tear-Off position. 19 Tally Dascom 1225 Restore Factory [S3]+[S4]+[S5] Defaults Restore settings to factory defaults except for Change Pin, Vertical Alignment and Adjust Page Margin Parameters. Firmware [S2]+[S3]+[S4]+ Update [S5] x Alternate flashing of L9 and L10 indicates ready for firmware update from host. x When new firmware is being received: L1 and L2 will flash, followed by L1 and L3 flashing, then followed by L1 and L4 flashing. x When downloading is completed, the carriage returns to home position. Printer initializes normally. x Allows user to select one of the following languages: Language Setup [S3]+[S4] English, German, Russian, Italian, French, Spanish and Turkish. Factory default is English. Refer to Language Setup section below for details. Language Setup The panel menu can display the following languages: English, German, Russian, Italian, French, Spanish and Turkish. Factory default setting is English. To change it to another language, hold down the [LF/FF] and [Load/Eject] keys on the panel and power-on. Upon exiting the Language Setup Menu, a listing of the current configuration is printed, and this is followed by Main Menu Setup. Below is an example of changing from English to German language: 20 Tally Dascom 1225 5. Printer Setting Changes In order to meet individual print requirements, the printer configurations may be changed as follows: Hold down the Tear Off key while powering on the printer, release the Tear Off key when the print head starts to move. The printer will enter Main Menu setup state. Follow the instructions printed on how to make setting changes. When a new setting is saved, it is retained after the printer has been powered off. The Main Menu is grouped into 5 sub-menus: System Setup, Page Setup, Print Setup, Interface Setup and Advanced Setup. A detailed description of the sub-menus is given below. The settings in bold and italic refer to the default settings. System Setup System Setup Emulation Auto CR (IBM) Auto LF Valid Settings Function ESC/P2, IBM 2390 Selects the printer emulation. This should be the same as the host Plus printer driver. Yes, No Yes, No Yes: LF = LF+CR; No: LF = LF (Applies to IBM emulation only) Yes: CR = CR+LF; No: CR = CR Auto: Text & graphics in bi-direction; double height in uni-direction. Print Dir Bi-Dir, Uni-Dir, Uni-Dir: Prints everything in uni-direction. Bi-dir: Prints everything in Auto bi-direction. Note: Top position print direction may be affected by Top Print Dir setting. Top Print Dir Bi-Dir, Uni-Dir Bi-dir: Prints top position according to Print Dir setting. Uni-dir: Prints top position in uni-direction regardless of Print Dir setting. Impact Normal, Heavy Heavy: Higher impact force for multipart printing IBM AGM Yes, No Selects the IBM graphic mode. Applies to IBM emulation only Print Setup Print Setup Valid Settings Function When Font is set to “Others” Font (Others) OCR-B, OCR-A, ORATOR, GOTHIC, SOUVENIR on control panel, OCR-B, OCR-A, ORATOR, GOTHIC fonts are selectable. Pitch 10cpi, 12cpi, 15cpi, 17cpi, 20cpi, PS Zero 0,Ø Controls the characters per inch setting. Selects slashed or no-slash zero. 21 Tally Dascom 1225 HS-Draft On: Prints High Speed Draft On, Off when Draft font is selected. When printing 180x180 DPI Graphic Speed graphics: Normal – prints in 180x180 DPI, Fast – prints in Normal, Fast, Ultra 90x180 DPI, Ultra – prints in 60x180 DPI. IBM Set 1/2 Selects the IBM character Set 1, Set 2 set. 1: Normal; 2: Extended USA, France, Germany, UK, Denmark, Sweden, Italy, Int'l Char Set Spain, Japan, Norway, Denmark II, Spain II, Latin AM, Korea, Legal 14+1 international character set selections 1. CP 437 2. CP 737 3. CP 850 4. CP 851 5. CP 852 6. CP 857 7. CP 858 8. CP 860 9. CP 861 10. CP 863 11. CP 864 12. CP 864 Extended 13. CP 865 14. CP 866 Cyrillic Code Page National code page 15. CP 866 Bulgaria selections 16. CP 1250 17. CP 1251 18. CP 1252 19. CP 1253 20. CP 1254 21. 8859-1 22. 8859-1 (SAP) 23. 8859-2 24. 8859-5 25. 8859-7 26. 8859-9 27. 8859-15 28. BRASCII 29. Abicomp 22 Tally Dascom 1225 30. Roman8 31. Coax/Twinax 32. New-437 33. New-Dig 850 34. Old-Code 860 35. Flarro 863 36. 865 Hebrew 37. CP 1257 38. 866 Ukraine 39. 866 Kazakhstan 40. Kamenicky 41. Mazovia 42. CP 775 43. CRO-ASCII 44. Arabic Farsi 45. Arabic Urdu 46. Greek DEC 47. Greek ELOT 928 Character Table Character table type Graphic Table, Italic Table selection Page Setup Page Setup Valid Settings Function Print Width 13.6", 8" Printable width options Line Per Inch 1, 2, 3, 4, 5, 6, 7, 8 Sets the line spacing 3",3.5",11/3", 4", 5", 5.5" Fanfold Form Length 6",7",8", 8.5",11", 70/6", 12", Sets the page length for tractor mode 14", 17" Fanfold Top Margin Fanfold Bottom Margin Sets the top margin for tractor mode. Due to 0/60" … 10/60"…99/60" mechanical tolerance, 0/60” is not guaranteed. Sets the bottom margin for tractor mode. Due to 0/60"…10/60"...30/60" mechanical tolerance, 0/60” is not guaranteed. 3", 3.5", 11/3", 4", 5", 5.5", 6", Single Form Length 7", 8", 8.5", 11", 70/6", 12", 14", Sets the page length for friction mode 17" Single Top Margin 0/60" … 10/60"…99/60" Single Bottom Margin 0/60"…10/60"...30/60" Roll Paper Yes, No Perforation Skip Yes, No Sets the top margin for friction mode. Due to mechanical tolerance, 0/60” is not guaranteed. Sets the bottom margin for friction mode. Due to mechanical tolerance, 0/60” is not guaranteed. In friction mode, [LF/FF] will not eject the paper and feed to next page. (Assume roll paper) Skips printing on perforation area 23 Tally Dascom 1225 Specifies the waiting time before feeding the page to tear-off position automatically. Manual: Auto Tear Manual, 0.5s, 1s, 2s, 3s, 4s, 5s Auto tear mode is off. View1s, View2s, View3s: View1s, View2s, View3s After printing is completed, the printer will feed the paper until the last printed line is at the tear-off position. (Applies to tractor mode only) Interface Setup Interface Valid Settings Setup Function For multi-host connection. Auto: First come first served; Interface Auto, Parallel, USB Parallel/USB: Serves the designated host only. I-PRIME Yes, No Yes: Host I-Prime signal resets the printer. Auto IF Delay Determines the waiting time before receiving data from another 10s, 30s interface. User Font: Part of RAM is used for user download characters; Buffer: Disables user character download function; uses RAM for RAM Usage User Font, Buffer expanded buffer size up to 48KB. Yes: Sets the parallel interface of the printer to bidirectional mode (IEEE 1284, Nibble mode), e.g. for Windows Plug & Play. No: Sets the interface to compatibility mode in order to ensure CX Bid reliable operation with special external boxes. Yes, No Advanced Setup Advanced Setup Valid Settings Function Specifies the waiting time before loading a cut Auto Load sheet automatically. Manual: Auto load mode is Manual, 0.5s, 1s, 1.5s, 2s off. (Applies to friction mode only) Paper Jam Prevention Flattens paper edges by carriage movement Yes, No before printing starts. Yes: Detects paper out and halts printing; Paper End Detect otherwise, ignores paper out and continues Yes, No printing. Form Length Ctrl Software, Ignore Ignore: Ignores form length commands Pitch Ctrl Software, Ignore Ignore: Ignores CPI commands Font Ctrl Software, Ignore Ignore: Ignores font select commands Quality Ctrl Software, Ignore Ignore: Ignores print quality commands Buzzer Yes, No Yes: Sounds buzzer on all hardware errors 24 Tally Dascom 1225 German (Deutsch) System Setup Valid Settings Emulation ESC/P2, IBM 2390 Plus Auto CR (IBM) Ja, Nein Auto LF Ja, Nein Druck Dir Bi-Dir, Uni-Dir, Auto Top Druck Dir Bi-Dir, Uni-Dir Anschlag Normal, Stark IBM AGM Ja, Nein Druck Setup Valid Settings Font (Andere) OCR-B,OCR-A,ORATOR,GOTHIC,SOUVENIR Zeichenteilung 10cpi, 12cpi, 15cpi, 17cpi, 20cpi, PS Null 0,Ø HS-Draft An, Aus Graphikgeschw. Normal, Schnell, Ultra IBM Set ½ Set 1, Set 2 USA, Frankreich, Deutschland, UK, Dänemark, Schweden, Land Italien, Spanien, Japan, Norwegen, Dänemark II, Spanien II, Latein-Amerika, Korea, Legal Zeichensatz CP 437, CP 857… Zeichentabelle Graphik, Italic Valid Settings Seiten Setup Druckbreite 13.6", 8" Zeilen Pro Zoll 1, 2, 3, 4, 5, 6, 7, 8 Endlos Formularlänge 3",3.5",11/3", 4", 5", 5.5" 6",7",8", 8.5",11", 70/6", 12", 14", 17" Endlos Oberer Rand 0/60" … 10/60"…99/60" Endlos Unterer Rand 0/60"…10/60"...30/60" Einzel Formularlänge 3", 3.5", 11/3", 4", 5", 5.5", 6", 7", 8", 8.5", 11", 70/6", 12", 14", 17" Einzel Oberer Rand 0/60" … 10/60"…99/60" Einzel Unterer Rand 0/60"…10/60"...30/60" Rollenpapier Ja, Nein Perforationssprung Ja, Nein Abreissen Manuell, 0.5s, 1s, 2s, 3s, 4s, 5s, view1s, view 2s, view 3s Valid Settings Schnittstellen Setup Schnittstelle Auto, Parallel, USB I-PRIME Ja, Nein 25 Tally Dascom 1225 Auto IF Delay 10s, 30s RAM Nutzung Ladbarer Font, Puffer CX Bid Ja, Nein Valid Settings Erweitertes Setup Auto Laden Manuell, 0.5s, 1s, 1.5s, 2s Papierstau Vorbeugung Ja, Nein Papierende Detekt Ja, Nein Formularlänge Strg Software, Ignoriere Zeichenteilung Strg Software, Ignoriere Font Strg Software, Ignoriere Qualität Strg Software, Ignoriere Summer Ja, Nein Russian (Ɋɨɫɫɢɹ) ɋɢɫɬɟɦɧɵɟ ɭɫɬɚɧɨɜɤɢ Valid Settings ɗɦɭɥɹɰɢɹ ESC/P2, IBM 2390 Plus Ⱥɜɬɨ CR (IBM) Ⱦɚ, ɇɟɬ Ⱥɜɬɨ LF Ⱦɚ, ɇɟɬ ɇɚɩɪɚɜɥɟɧɢɟ ɩɟɱɚɬɢ Ⱦɜɭɧɚɩɪɚɜɥɟɧɧɚɹ, Ɉɞɧɨɧɚɩɪɚɜɥɟɧɧɚɹ, Ⱥɜɬɨ ɇɚɩɪɚɜɥɟɧɢɟ ɩɟɱɚɬɢ ɡɚɝɥ. ɛɭɤɜ Ⱦɜɭɧɚɩɪɚɜɥɟɧɧɚɹ, Ɉɞɧɨɧɚɩɪɚɜɥɟɧɧɚɹ ɍɞɚɪ ɇɨɪɦɚɥɶɧɵɣ, ɋɢɥɶɧɵɣ IBM AGM Ⱦɚ, ɇɟɬ ɇɚɫɬɪɨɣɤɚ ɩɟɱɚɬɢ Valid Settings Ⱦɨɩɨɥɧɢɬɟɥɶɧɵɣ ɲɪɢɮɬ OCR-B,OCR-A,ORATOR,GOTHIC,SOUVENIR ɡɧɚɤɨɜ/ɞɸɣɦ 10cpi, 12cpi, 15cpi, 17cpi, 20cpi, PS ɉɟɪɟɱɟɪɤɧɭɬɵɣ ɧɨɥɶ 0,Ø ȼɵɫɨɤɚɹ ɫɤɨɪɨɫɬɶ ȼɤɥ, ȼɵɤɥ ɋɤɨɪɨɫɬɶ ɝɪɚɮɢɤɢ ɇɨɪɦɚɥɶɧɚɹ, Ȼɵɫɬɪɚɹ, Ɉɱɟɧɶ ɛɵɫɬɪɚɹ ɋɢɦɜɨɥɵ IBM 1/2 ɍɫɬ. 1, ɍɫɬ. 2 USA, France, Germany, UK, ¿Ûèãú, Sweden, Italy, Spain, ɇɚɛɨɪ ɡɧɚɤɨɜ Japan, ÈéëÝàÞãú, ¿Ûèãú II, Spain II, ÆÛíãè ìåÛú Ⱥɦɟɪɢɤɚ, Korea, Legal Ʉɨɞɨɜɚɹ ɬɚɛɥɢɰɚ CP 437, CP 857… Ɍɚɛɥɢɰɚ ɡɧɚɤɨɜ Ƚɪɚɮɢɤɚ, Ʉɭɪɫɢɜ ɉɚɪɚɦɟɬɪɵ ɫɬɪɚɧɢɰɵ Valid Settings ɒɢɪɢɧɚ ɩɟɱɚɬɢ 13.6", 8" ɋɬɪɨɤ ɧɚ ɞɸɣɦ 1, 2, 3, 4, 5, 6, 7, 8 26 Tally Dascom 1225 Ⱦɥɢɧɚ ɮɨɪɦɵ ɞɥɹ ɧɟɩɪɟɪɵɜɧɨɣ ɛɭɦɚɝɢ Ɉɬɫɬɭɩ ɫɜɟɪɯɭ ɞɥɹ ɧɟɩɪɟɪɵɜɧɨɣ ɛɭɦɚɝɢ Ɉɬɫɬɭɩ ɫɧɢɡɭ ɞɥɹ ɧɟɩɪɟɪɵɜɧɨɣ ɛɭɦɚɝɢ Ⱦɥɢɧɚ ɮɨɪɦɵ ɞɥɹ ɨɬɞɟɥɶɧɵɯ ɥɢɫɬɨɜ 3",3.5",11/3", 4", 5", 5.5" 6",7",8", 8.5",11", 70/6", 12", 14", 17" 0/60" … 10/60"…99/60" 0/60"…10/60"...30/60" 3", 3.5", 11/3", 4", 5", 5.5", 6", 7", 8", 8.5", 11", 70/6", 12", 14", 17" Ɉɬɫɬɭɩ ɫɜɟɪɯɭ ɞɥɹ ɨɬɞɟɥɶɧɵɯ ɥɢɫɬɨɜ 0/60" … 10/60"…99/60" Ɉɬɫɬɭɩ ɫɧɢɡɭ ɞɥɹ ɨɬɞɟɥɶɧɵɯ ɥɢɫɬɨɜ 0/60"…10/60"...30/60" Ɋɭɥɨɧɧɚɹ ɛɭɦɚɝɚ Ⱦɚ, ɇɟɬ ɉɪɨɩɭɫɤ ɩɟɪɮɨɪɚɰɢɢ Ⱦɚ, ɇɟɬ Ⱥɜɬɨ ɩɪɨɝɨɧ Ɋɭɱɧɨɣ, 0.5s, 1s, 2s, 3s, 4s, 5s, view1s, view 2s, view 3s ɍɫɬɚɧɨɜɤɢ ɢɧɬɟɪɮɟɣɫɚ Valid Settings ɂɧɬɟɪɮɟɣɫ Ⱥɜɬɨ, ɉɚɪɚɥɟɥ, USB ɉɚɪɚɥɟɥ. ɩɨɪɬ Ⱦɚ, ɇɟɬ ȼɪɟɦɹ ɨɠɢɞɚɧɢɹ 10s, 30s ɇɚɡɧɚɱɟɧɢɟ RAM ɉɨɥɶɡɨɜ. ɲɪɢɮɬ, Ȼɭɮɟɪ CX Bid Ⱦɚ, ɇɟɬ Ⱦɨɩɨɥɧɢɬɟɥɶɧɵɟ ɭɫɬɚɧɨɜɤɢ Valid Settings Ⱥɜɬɨɡɚɝɪɭɡɤɚ Ɋɭɱɧɚɹ, 0.5s, 1s, 1.5s, 2s Ⱦɚɬɱɢɤ ɞɜɢɠ. ɛɭɦɚɝɢ Ⱦɚ, ɇɟɬ Ⱦɚɬɱɢɤ ɤɨɧɰɚ ɛɭɦɚɝɢ Ⱦɚ, ɇɟɬ Ʉɨɧɬɨɥɶ ɞɥɢɧɵ ɮɨɪɦɵ ɉɪɨɝɪɚɦɧɵɣ, ɂɝɧɨɪ. Ʉɨɧɬɪɨɥɶ ɡɧɚɤɨɜ/ɞɸɣɦ ɉɪɨɝɪɚɦɧɵɣ, ɂɝɧɨɪ. Ʉɨɧɬɪɨɥɶ ɲɪɢɮɬɚ ɉɪɨɝɪɚɦɧɵɣ, ɂɝɧɨɪ. Ʉɨɧɬɪɨɥɶ ɤɚɱɟɫɬɜɚ ɉɪɨɝɪɚɦɧɵɣ, ɂɝɧɨɪ. Ɂɜɭɤ Ⱦɚ, ɇɟɬ Italian (Italiano) Menu Sistema Valid Settings Emulazione ESC/P2, IBM 2390 Plus Auto CR (IBM) Si, No Auto LF Si, No Direz. Stampa Bi-Dir, Uni-Dir, Auto Top Print Dir Bi-Dir, Uni-Dir Impatto Normale, Pesante IBM AGM Si, No 27 Tally Dascom 1225 Menù Stampa Valid Settings Fonte (Altre) OCR-B,OCR-A,ORATOR,GOTHIC,SOUVENIR Spaziatura 10cpi, 12cpi, 15cpi, 17cpi, 20cpi, PS Zero 0,Ø HS-Bozza Si, No Veloc. Grafica Normale, Veloce, Ultra IBM Set 1/2 Set 1, Set 2 USA, Francia, Germania, Regno Unito, Danimarca, Svezia, Set Carat. Int. Italia, Spagna, Giappone, Norvegia, Danimarca II, Spagna II, America Latina, Korea, Legal Code Page CP 437, CP 857… Tab.Carattere Tab. Grafica, Italico Menù Pagina Valid Settings Larghezza di stampa 13.6", 8" Interlinea 1, 2, 3, 4, 5, 6, 7, 8 Lungh. Mod. Continuo 3",3.5",11/3", 4", 5", 5.5" 6",7",8", 8.5",11", 70/6", 12", 14", 17" Margine Sup. Continuo 0/60" … 10/60"…99/60" Margine Inf. Continuo 0/60"…10/60"...30/60" Lunghezza Foglio 3", 3.5", 11/3", 4", 5", 5.5", 6", 7", 8", 8.5", 11", 70/6", 12", 14", 17" Margine Sup. Foglio 0/60" … 10/60"…99/60" Margine Infer. Foglio 0/60"…10/60"...30/60" Rullo Carta Si, No Salto Perforazione Si, No Autostrappo Manuale, 0.5s, 1s, 2s, 3s, 4s, 5s, view1s, view 2s, view 3s Menù Interfacc. Valid Settings Interfaccia Auto, Parallela, USB I-PRIME Si, No Ritardo Auto IF 10s, 30s Uso RAM Fonti utente, Memoria CX Bid Si, No Menù Avanzato Valid Settings Autocaricamento Manuale, 0.5s, 1s, 1.5s, 2s Previene Inceppamento Si, No Rileva Fine Carta Si, No Control. Lungh. Carta Software, Ignora Control. Spaziatura Software, Ignora 28 Tally Dascom 1225 Controllo Fonti Software, Ignora Controllo Qualità Software, Ignora Cicalino Si, No French (Français) Setup système Valid Settings Emulation ESC/P2, IBM 2390 Plus RC-Auto (IBM) Oui, Non SL-Auto Oui, Non Dir Impr. Bidir, Unidir, Auto Sup. Dir Impr. Bidir, Unidir Frappe Normal, Forte IBM AGM Oui, Non Setup impression Valid Settings Polices (Autres) OCR-B,OCR-A,ORATOR,GOTHIC,SOUVENIR Densités caract. 10cpi, 12cpi, 15cpi, 17cpi, 20cpi, PS Zéro 0,Ø HS-Draft Oui, Non Vitesse graphiq. Normal, Rapide, Ultra IBM Set 1/2 Set 1, Set 2 USA, France, Allemagne, Royaume-Uni, Denmark, Suède, Italie, Pays Espagne, Japon, Norvège, Denmark II, Espagne II, Amerique latine, Korea, Legal Jeu de caractèr. CP 437, CP 857… Tabl.de caract. Graphique, Italique Valid Settings Setup page Largeur d'impression 13.6", 8" Lignes par pouce 1, 2, 3, 4, 5, 6, 7, 8 Papier continu Longueur formulaire 3",3.5",11/3", 4", 5", 5.5" 6",7",8", 8.5",11", 70/6", 12", 14", 17" Papier continu Bord supérieure 0/60" … 10/60"…99/60" Papier continu Bord inférieure 0/60"…10/60"...30/60" Feuille à feuille Longueur formulaire 3", 3.5", 11/3", 4", 5", 5.5", 6", 7", 8", 8.5", 11", 70/6", 12", 14", 17" Feuille à feuille Bord supérieur 0/60" … 10/60"…99/60" Feuille à feuille Bord inférieur 0/60"…10/60"...30/60" Papier du rouleau Oui, Non Sauter la perforation Oui, Non Coupe Auto Manuel, 0.5s, 1s, 2s, 3s, 4s, 5s, view1s, view 2s, view 3s 29 Tally Dascom 1225 Setup interface Valid Settings Interface Auto, Parallel, USB I-PRIME Oui, Non Auto IF Delay 10s, 30s Utilisation RAM User Font, Buffer CX Bid Oui, Non Setup élargi Valid Settings Chargem. Autom. Manuel, 0.5s, 1s, 1.5s, 2s Prévention bourrage Qui, Non Détec.fin de pap Qui, Non Long.formul.Strg Software, Ignorer Densi.caract.Strg Software, Ignorer Police Strg Software, Ignorer Qualité Strg Software, Ignorer Vibrateur Qui, Non Spanish (Español) System Setup Valid Settings Emulación ESC/P2, IBM 2390 Plus Auto CR(IBM) Si, No Auto LF Si, No ModoImpresión Bi-Dir, Uni-Dir, Auto ModoImp.Borde Bi-Dir, Uni-Dir Impacto Normal, Fuerte IBM AGM Si, No Print Setup Valid Settings Fuente (Otros) OCR-B,OCR-A,ORATOR,GOTHIC,SOUVENIR Tamaño Letra 10cpp, 12cpp, 15cpp, 17cpp, 20cpp, PS Cero 0,Ø Alta Velocidad Activado, Desactivado Imp. Grafica Normal, Rápido, Ultra IBM Juego 1/2 Juego 1, Juego 2 USA, Francia, Alemania, Reino Unido, Dinamarca, Suecia, Italia, Carácter Local España, Japón, Noruega, Dinamarca II, España II, AméricaLatina, Corea, Legal Tabla Carácter CP 437, CP 857… Tipo Tabla Tabla Gráfica, Italica 30 Tally Dascom 1225 Page Setup Valid Settings Ancho de Impresión 13.6", 8" Lineas Por Pulgada 1, 2, 3, 4, 5, 6, 7, 8 Tamaño Papel Continuo 3",3.5",11/3", 4", 5", 5.5" 6",7",8", 8.5",11", 70/6", 12", 14", 17" Margen Sup. Pap Cont. 0/60" … 10/60"…99/60" Margen Inf. Pap.Cont. 0/60"…10/60"...30/60" Tamaño Hojas Sueltas 3", 3.5", 11/3", 4", 5", 5.5", 6", 7", 8", 8.5", 11", 70/6", 12", 14", 17" Margen Sup. Folios 0/60" … 10/60"…99/60" Margen Inf. Folios 0/60"…10/60"...30/60" Rollo de Papel Si, No Salto perforación Si, No Mover a PosiciónCorte Manual, 0.5s, 1s, 2s, 3s, 4s, 5s, view1s, view 2s, view 3s Interface Setup Valid Settings Interface Auto, Paralelo, USB I-Prime Si, No Auto retraso 10s, 30s Uso de RAM Font Usuario, Buffer CX Bid Si, No Advanced Setup Valid Settings Auto Carga Manual, 0.5s, 1s, 1.5s, 2s Prevención Atascos Si, No Detección Fin Papel Si, No Control Tamaño Papel Software, Ignorar Control Tamaño Letra Software, Ignorar Control Fuente Software, Ignorar Control Calidad Software, Ignorar Alarma Si, No Turkish (Türkce) Sistem Ayarı Valid Settings Benzetim/Emulation ESC/P2, IBM 2390 Plus Otom. Satırbaġı (IBM) Evet, Hayır Otom. Satır besleme Evet, Hayır Yazdırma yönü òki-Yöne, Tek-Yöne, Otom. Üstte yazdırma yönü òki-Yöne, Tek-Yöne Vuruġ Normal, Güçlü 31 Tally Dascom 1225 IBM AGM Evet, Hayır Yazdırma Ayarları Valid Settings Yazı Tipi (Diáer) OCR-B,OCR-A,ORATOR,GOTHIC,SOUVENIR Karakter Sıklıáı 10cpi, 12cpi, 15cpi, 17cpi, 20cpi, PS Sıfır 0,Ø Yük.Hız-Taslak On, Off Grafik Hızı Normal, Hızlı, Ultra IBM Karakter Seti 1/2 Set 1, Set 2 Amerika Bir.Devleti, Fransa, Almanya, øngiltere, Danimarka, Uluslararası Kar. Seti øsveç, øtalya, øspanya, Japonya, Norveç, Danimarka II, øspanya II, Latin Amerika, Korea, Legal Kod Sayfası CP 437, CP 857… Karakter Tablosu Grafik Tablosu, òtalik Sayfa Düzeni Ayarı Valid Settings Baskı Geniúli÷i 13.6", 8" ònç baġına satır 1, 2, 3, 4, 5, 6, 7, 8 Sürekli-kaáıt Form Uzunluáu 3",3.5",11/3", 4", 5", 5.5" 6",7",8", 8.5",11", 70/6", 12", 14", 17" Sürekli-kaáıt Üst kenar boġluáu 0/60" … 10/60"…99/60" Sürekli-kaáıt Alt kenar boġluáu 0/60"…10/60"...30/60" Tek-kaáıt Form uzunluáu 3", 3.5", 11/3", 4", 5", 5.5", 6", 7", 8", 8.5", 11", 70/6", 12", 14", 17" Tek-kaáıt Üst kenar boġluáu 0/60" … 10/60"…99/60" Tek-kaáıt Alt kenar boġluáu 0/60"…10/60"...30/60" Rulo kaáıt Evet, Hayır Delik atlama Evet, Hayır Otom. Koparma Elle/Manuel, 0.5s, 1s, 2s, 3s, 4s, 5s, view1s, view 2s, view 3s Arabirim Ayarları Valid Settings Arabirim Otom., Paralel, USB I-Prime Evet, Hayır Otom. Arabirim gecikmesi 10s, 30s RAM Kullanımı Kullanıcı Yazı Tipi, Arabellek CX Bid Evet, Hayır Geliġtirilmiġ Ayarlar Valid Settings Otom. Yükleme Elle/Manuel, 0.5s, 1s, 1.5s, 2s Kaáıt Sıkıġmasını Önleme Evet, Hayır Kaáıt Sonunu Algılama Evet, Hayır Form Uzunl. Kont. Yazılım, Yoksay 32 Tally Dascom 1225 Karak.Sıkl. Kont. Yazılım, Yoksay Yazı Tipi Kont. Yazılım, Yoksay Kalite Kont. Yazılım, Yoksay Alarm Zili Evet, Hayır 33 Tally Dascom 1225 Vertical Alignment The vertical alignment function is used to resolve any vertical line misalignments in bi-directional printing. Adjust Vertical Alignment Procedure: 1. Enter the Service Menu by holding down theɋTear/OffɌandɋLF/FFɌkeys while powering up. 2. Load paper. 3. The printer will print as follows: Service Menu ɋLF/FFɌ= OK ɋTear/OffɌ= Back ɋLoad/EjectɌ= Next ɋOnlineɌ= Exit Current SettingφVertical Alignment 4. PressɋLF/FFɌkey to select the current setting. The printer will print as follows: Vertical Alignment ɋLF/FFɌ= OK ɋTear/OffɌ= Back ɋLoad/EjectɌ= Next ɋOnlineɌ= Exit Please select Paper TypeφSingle Ply For single ply paper, pressɋLF/FFɌkey to select. For multipart paper, press ɋLoad/EjectɌkey to go to “Multipart”ˈthen pressɋLF/FFɌkey to select. 5. If single ply is selected for paper type, the following will print: Single Ply Current Print Mode: LQ Press ɋLoad/EjectɌkey to scroll to other print modes if required. 6. If LQ is selected, the following will print: LQ ɋLF/FFɌ= lower ½ to left ɋLoad/EjectɌ= lower ½ to right ɋOnlineɌ= Exit LQ -2: |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||| Pressing ǏLF/FFǐor ǏLoad/Ejectǐ key will allow you to adjust the alignment of the vertical lines 34 Tally Dascom 1225 printed above. 7. Once the setting which gives the best alignment is found, press ɋOnlineɌ key to exit current level. Printer will print “Save settings? Yes”. Press ɋLF/FFɌ key to save setting. Press ǏOnlineǐ key a few times until the printer exits the Service Menu. Change Pin Function When printer has been used for a long time or the print volume is high, the frequently used print head pins may fail. The Change Pin function enables the user to continue using the printer for a while without compromise in print quality until a suitable print head replacement is available. This function will reduce the print speed if activated. Change Pin Procedure: 1. Enter the Service Menu by holding down theɋTear/OffɌandɋLF/FFɌkeys while powering up. 2. Load paper. 3. The printer will print as below: Service Menu ɋLF/FFɌ=OK ɋTear/OffɌ= Back ɋLoad/EjectɌ= Next ɋOnlineɌ= Exit Current MenuφVertical Alignment Press ǏLoad/Ejectǐ key to scroll to “Change Pin”ˈthen press ɋLF/FFɌ key to select. The status of each pin will be printed as follows: Change Pin 1 ---------- Is this pin OK? Yes / No 2 ---------- Is this pin OK? Yes / No 3 ---------- Is this pin OK? Yes / No 24 ---------- Is this pin OK? Yes / No Press ɋLoad/EjectɌ key to choose whether the pin is Yes or Noˈthen press ɋLF/FFɌ key to confirm selection. 4. When all the 24 pins are evaluated, press ɋOnlineɌ. The printer will print “Save settings? Yes”. Press ɋLF/FFɌ key to confirm selection. Press ǏOnlineǐ key a few times until the printer exits the Service Menu. 35 Tally Dascom 1225 Adjust Physical Margins Adjust Page Margins allows for adjustments of physical left, top margins and tear-off position. Warning: Once these settings are changed, resetting the printer to factory defaults will not initialize these settings back to the original settings; so it is not advisable to perform this adjustment unless it is absolutely necessary. Adjust Top Margin Procedure: 1. Enter the Adjust Page Margins function by holding down theɋLoad/EjectɌandɋOnlineɌkeys while powering up until the printer beeps twice. 2. Load paper. 3. The printer will print as below: Adjust Page Margins: ɋLF/FFɌ=OK ɋTear/OffɌ= Back ɋLoad/EjectɌ= Next ɋOnlineɌ= Exit Current Setting: Adjust Fanfold Top Margin PressǏLF/FFǐkey to confirm selection if the paper used is fanfold type. The printer will print as follows: Procedure˖ Install fanfold paper to tractors ǏLF/FFǐ = Add ǏLoad/Ejectǐ = Reduce ǏOnlineǐ = Exit Each step is 0.5 mm Function of keys: ǏLoad/Ejectǐkey: Decrease 0.5mm ǏLF/FFǐkey: Increase 0.5mm 4. Press ǏOnlineǐ key, printer will print “Save settings˛Yes”. Press ǏLoad/Ejectǐ key to choose Yes or Noˈthen press ǏLF/FFǐ key to confirm selection and exit “Adjust Page Margins” mode by pressing ǏOnlineǐ. The print head moves to the left side and the printer beeps twice, then the print head moves to the middle position. Adjust Left Margin Procedure: 1. Enter the Adjust Page Margins function by holding down theɋLoad/EjectɌandɋOnlineɌkeys while powering up until the printer beeps twice. 2. Load paper. 3. The printer will print as below: Adjust Page Margins: ɋLF/FFɌ=OK ɋTear/OffɌ= Back ɋLoad/EjectɌ= Next ɋOnlineɌ= Exit Current Setting: Adjust Fanfold Top Margin 4. PressǏLoad/Ejectǐkey until the current setting is “Adjust Fanfold Left Margin”. PressǏLF/FFǐkey to confirm selection if the paper used is fanfold type. The printer will print as follows: Adjust Fanfold Left Margin 5. Press ɋTear OffɌor ɋLoad/EjectɌ to reduce or increase the left margin, respectively, by one 36 Tally Dascom 1225 unit of 1/60 inch. 6. When satisfied with the left margin setting, press ǏOnlineǐ key, printer will print “Save settings˛ Yes”. Press ǏLoad/Ejectǐ key to choose Yes or No, then press ǏLF/FFǐ key to confirm selection and exit “Adjust Page Margins” mode by pressing ǏOnlineǐ. The print head moves to the left side and the printer beeps twice, then the print head moves to the middle position. Adjust Tear-Off Position Procedure: 1. Enter the Adjust Page Margins function by holding down theɋLoad/EjectɌandɋOnlineɌkeys while powering up until the printer beeps twice. 2. Load fanfold paper 3. The printer will print as below: Adjust Page Margins: ɋLF/FFɌ=OK ɋTear/OffɌ= Back ɋLoad/EjectɌ= Next ɋOnlineɌ= Exit Current Setting: Adjust Fanfold Top Margin 4. PressǏLoad/Ejectǐkey until the current setting is “Adjust Tear-Off Position”. PressǏLF/FFǐkey to confirm selection. The printer will print as follows: Procedure˖ Install fanfold paper to tractors ǏLF/FFǐ = Add ǏLoad/Ejectǐ = Reduce ǏOnlineǐ = Exit Each step is 0.5 mm Function of keys: ǏLoad/Ejectǐkey: Decrease 0.5mm ǏLF/FFǐkey: Increase 0.5mm 5. Press ǏOnlineǐ key, printer will print “Save settings˛Yes”. Press ǏLoad/Ejectǐ key to choose Yes or Noˈthen press ǏLF/FFǐ key to confirm selection and exit “Adjust Page Margins” mode by pressing ǏOnlineǐ. The print head moves to the left side and the printer beeps twice, then the print head moves to the middle position. 37 Tally Dascom 1225 Dascom Printer Setup Tool In the CDROM is a software utility called “Dascom Printer Setup”. This application enables a convenient, simple and fast way to control your printer without touching any keys on the operation panel. 1. Start the tool installation by double clicking the “Dascom Printer Setup.exe”. 2. Connect the printer to the system using USB cable 3. Power up the printer. 4. Load paper into the printer. (Note: The tool cannot get connected to the printer when the printer is offline.) 5. Run the tool from the Windows Start menu by selecting All Programs, then Dascom Printer Setup, and then Tally Dascom Printer Setup. 6. For more information on how to use the tool, go to the Help menu and select User Guide. 38 Tally Dascom 1225 6 Maintenance Your printer requires very little care. Occasional cleaning and replacement of the ribbon cartridge are all that is required. Cleaning is recommended approximately every 6 months or 300 hours of operation, whichever is sooner. Lubrication of the printer is not usually necessary. If the print head carriage does not move smoothly back and forth, clean the printer in the manner described in this chapter. If the problem continues, contact your dealer to determine whether lubrication may be necessary. Switch printer off and unplug the power cord from the mains before doing any maintenance work. Cleaning The housing and the top cover of the printer help protect it against dust, dirt, and other contaminants. However, paper produces small particles that accumulate inside the printer. This section explains how to clean and vacuum the printer and how to clean the paper bail rollers. It is easier to clean the printer when the cover is open. Cleaning and Vacuuming the Printer If the print head carriage does not move smoothly back and forth or paper particles have accumulated in the printer, clean the printer. To clean and vacuum the printer: 1. Remove any paper from the printer. Make sure that the power is off, and then disconnect the printer power cord. 2. Using a soft vacuum brush, vacuum the exterior of the printer. Also vacuum the cut sheet edge. 3. Use a soft, damp cloth to wipe the exterior of the printer, including the cover. A mild detergent may be used. Do not use solvents, kerosene, or abrasive cleaning materials that may damage the printer. 4. Open the cover of the printer and remove the ribbon cartridge. Using a soft vacuum brush, gently vacuum the platen, the print head carriage and shaft, and surrounding areas. You can easily slide the print head to the left or right when the power is off. Be careful not to press too hard on the flat head cable that extends from the print head carriage. 5. Re-install the ribbon cartridge. 6. Remove the single sheet feeder and clean the form tractors and the surrounding areas. 7. Re-install the single sheet feeder. Cleaning the Paper Rollers Clean the platen and paper bail rollers occasionally or when stains or smudges appear on the paper. Use a mild detergent as appropriate. Do not use alcohol to clean the platen or the rollers. Alcohol may cause the rubber to harden. To clean the rollers and the platen: 1. Apply a small amount of water to a soft cloth. Avoid spilling liquid inside the printer. 2. Place the cloth against the platen and manually rotate the paper feed knob. 3. Repeat this procedure for each roller. 39 Tally Dascom 1225 4. To dry the platen, place a dry cloth against the platen and the rollers and manually rotate the paper feed knob. 40 Tally Dascom 1225 7 Troubleshooting Your printer is extremely reliable, but occasionally problems may occur. This chapter provides information on some of the common problems you may encounter and how you may solve them. If you encounter problems that you cannot resolve, contact your dealer or service partner for assistance. Print Quality Problems and Solutions Problem Solution • Make sure that the ribbon cartridge is properly installed and that the ribbon feeds smoothly. Printing is too light or too dark. • Replace the ribbon if necessary. • Make sure that the print gap lever is set for the thickness of your paper. • Make sure that the print gap lever is set for the thickness of your paper. Smears and stains appear on the • Check for ribbon wear. Replace the ribbon if necessary. page. • Check whether the tip of the print head is dirty. Clean the head with a soft cloth if necessary. • The print head may need to be replaced. • Make sure that the interface cable is securely connected to both the printer and computer. Printing is erratic or the wrong • Make sure that the printer driver selected in your software is the characters are printed. Many “?” or same as the emulation selected on the printer. unexpected characters are printed. • Check the length of the interface cable. (Maximum Parallel & USB: 2 meters) • Try another interface cable. The page is blank. • Make sure that the ribbon cartridge is properly installed. • Make sure the gap lever is set correctly. Printing is vertically misaligned Use the printer's vertical alignment function to check the vertical (jagged). print alignment. If necessary, adjust the print alignment. The top margin is wrong. Lines are double spaced instead of single spaced. The printer overprints on the same line. • Check the application top margin setting. • Adjust the Top Margin setting in Page Setup menu if necessary. Change the Auto LF setting in the System Setup menu to No. Change the Auto CR setting in the System Setup menu to No. The next print line starts where the previous line ended instead of at Change the Auto CR setting in the System Setup menu to Yes. the left margin. 41 Tally Dascom 1225 Paper Handling Problems and Solutions Problem Solution • Make sure that the paper select lever located on the top right of Paper cannot be loaded or fed. the printer is set correctly. Move the lever to the front for single sheets or to the rear for continuous forms. • Make sure that the paper covers the paper-out sensor. • Turn off the printer and remove the jammed paper. Remove any obstructions from the paper path. • Make sure that the Print Gap lever is set for the thickness of your Paper jams while loading. paper. • Make sure that the paper is not folded, creased, or torn. • Make sure that the left and right tractors are set so that the continuous forms are stretched taut. • Turn off the printer and remove the jammed paper. Remove any obstructions from the paper path. Paper jams while printing. • Make sure that the Print Gap lever is set for the thickness of your paper. • For continuous forms, make sure that the incoming and outgoing paper stacks are correctly placed. Paper should feed straight. Paper slips off the forms tractors or Make sure that the forms tractors are positioned correctly for the the perforated holes of the paper width of your paper and that the perforated holes of the paper fit tear during printing. directly over the tractor pins. Operating Problems and Solutions Problem Solution • Check whether the mains voltage is correct. • Make sure that the power cord is securely connected to both the printer and the mains power outlet. The power does not turn on. • Make sure that the power outlet is functional. If not so, use other outlet. • Turn the power off. Wait a minute and then turn the printer on again. If the printer still has no power, contact your dealer. • Make sure that the Online indicator is lit. • If you use the interface cable, make sure it is securely connected to both the printer and the computer. • Make sure paper is loaded. The printer is on but it will not print. • Run the printer Status Page. If printing executes normally, the problem is caused by: the interface, the computer, incorrect printer settings, or incorrect software settings. • Make sure that the printer driver selected in your software is the same as the emulation selected on the printer. 42 Tally Dascom 1225 If paper is loaded and the paper select lever is moved to the incorrect position, the printer turns offline, and the buzzer sounds Paper select lever error continuously. Switch the paper select lever back to its correct position. Printer Failures A user cannot generally resolve a problem involving defective printer hardware. Power off and on again the printer to recover any fatal error. If the problem cannot be resolved, contact your dealer or service partner. Error Indications on LEDs Error Operation Description Status Out No paper Normal Flash Paper Buzzer Online L1 Flash Normal On Off Off Stop Flash L7 L8 No No No No No No change change change change change change change change No No No No No No No change change change change change change change No No No No No No change change change change change change Once Flash Continuously Flash Flash Continuously No No No No No No No No change change change change change change change change Flash Flash Flash Carriage initial position L6 No /Tractor feed Print head hot L5 No Friction feed Flash L4 Off jammed Suspend L3 Sound Paper Suspend L2 -No No No No change change change change Off 43 No No change change Once Tally Dascom 1225 Diagnostic Functions The printer diagnostic functions are Self-Test page, hex-dump mode and print alignment adjustment. Self-Test page: Tells you whether the printer hardware is functioning correctly. If the printer hardware is functional, any problems you are having are probably caused by incorrect printer settings, incorrect software settings, the interface, or the computer. HEX-DUMP MODE: Allows you to determine whether the computer is sending the correct commands to the printer, and whether the printer is executing the commands correctly. This function is useful to programmers or others who understand how to interpret hex dumps. PRINTING ALIGNMENT ADJUSTMENT: Allows you to check and, if necessary, correct the printer’s vertical line print alignment in bi-directional mode. For details on using these functions, please refer to chapters 4 and 5. 44 Tally Dascom 1225 Firmware Update Sometimes it is necessary update the firmware to solve a problem. The latest firmware file may be obtained from your dealer or downloaded from our website www.dascom.com. Before upgrading firmware, it is strongly recommended to print the Main Menu page to keep a record of the old settings. Note: Firmware update should only be performed by an authorized service person. We disclaim any responsibility for any damage caused if it is performed by any other person. To load new firmware, proceed as follows: 1. Switch off the printer. Connect your PC to the parallel port on the printer. 2. Press and hold down 4 keys (S2, S3, S4, S5) while powering on the printer. 3. Alternate flashing of L9 and L10 LEDs indicates printer is ready for firmware update. 4. Go to the DOS prompt window. Copy the firmware file (with extension .MOT) to your printer as follows: COPY /B.mot PRN 5. When new firmware is being received, L1 and L2 will flash, followed by L1 and L3 flashing, then followed by L1 and L4 flashing. Note: Do not interrupt the downloading process to prevent possible flash memory corruption. 6. When downloading is completed, the carriage returns to home position. Printer initializes normally. Alternatively, you can use the Firmware Flash Tool version 3.5 or higher which is available in the CDROM and our website as well. Upon starting up the tool, choose the correct file and press "Update". 45 Tally Dascom 1225 8 General Specifications Print System Mono-chrome serial impact dot matrix Print Technology Uni-/bi-directional logic seeking for text and graphics Print Speed Font Matrix Print Head Graphics Pitch HS Draft Draft LQ 10 CPI 375/80H 250/120H 83/360H 12 CPI 300/120H 300/120H 100/360H 15 CPI 375/120H 375/120H 125/360H 17.1 CPI 426/120H 426/120H 142/360H 20 CPI 498/120H 498/120H 166/360H Pitch HS Draft Draft LQ 10 CPI 8x24/80H 12x24/120H 36x24/360H 12 CPI 10x24/120H 10x24/120H 30x24/360H 15 CPI 8x16/120H 8x16/120H 24x16/360H 17.1 CPI 7x24/120H 7x24/120H 21x24/360H 20 CPI 6x24/120H 6x24/120H 18x24/360H Proportional Nx24/36H Nx24/360H Nx24/360H Number of pins: 24 pins Firing frequency: Normal mode: 1500 Hz Pin diameter: 0.2 mm Life: 400 million strokes/pin @ Draft mode 8-bit mode: 8V x 60H, 80H, 90H, 120H, 240H (DPI) 24-bit mode: 24V x 60H, 90H, 120H, 180H, 360H (DPI) Paper Feed Speed Continuous feed: 5.0 IPS (inches per second) Resolution 360 x 360 DPI maximum Characters per line (CPL) Printable Columns (CPS/DPI) 10 CPI: 136 CPL 12 CPI: 163 CPL 15 CPI: 204 CPL 17.1 CPI: 232 CPL 20 CPI: 272 CPL 46 (Matrix/DPI) Tally Dascom 1225 Bitmap Fonts: 1. Draft 10, 12, 15, 17, 20 CPI 2. Roman 10, 12, 15, 17, 20 CPI, Proportional 3. Sans Serif 10, 12, 15, 17, 20 CPI, Proportional 4. Courier 10, 12, 15, 17, 20 CPI, Proportional 5. Prestige 10, 12, 15, 17, 20 CPI Built-In Fonts 6. OCR-B 10, 12, 17, 20 CPI 7. OCR-A 10, 12, 17, 20 CPI 8. Orator 10, 12, 15, 17, 20 CPI, Proportional 9. SOUVENIR 10, 12, 15, 17, 20 CPI, Proportional 10. GOTHIC 10, 12, 15, 17, 20 CPI, Proportional 11. Script 10, 12, 15, 17, 20 CPI 1. EAN-13 2. EAN-8 3. Interleaved 2 of 5 4. UPC-A 5. UPC-E Barcodes 6. Code 39 7. Code 128 8. POSTNET 9. Codabar 10. Industrial 2 of 5 1. CP 437 2. CP 737 3. CP 850 4. CP 851 5. CP 852 6. CP 857 7. CP 858 8. CP 860 Code Pages 9. CP 861 10. CP 863 11. CP 864 12. CP 864 Extended 13. CP 865 14. CP 866 Cyrillic 15. CP 866 Bulgaria 16. CP 1250 17. CP 1251 18. CP 1252 19. CP 1253 20. CP 1254 47 Tally Dascom 1225 21. 8859-1 22. 8859-1 (SAP) 23. 8859-2 24. 8859-5 25. 8859-7 26. 8859-9 27. 8859-15 28. BRASCII 29. Abicomp Code Pages 30. Roman8 31. Coax/Twinax 32. New-437 33. New-Dig 850 34. Old-Code 860 35. Flarro 863 36. 865 Hebrew 37. CP 1257 38. 866 Ukraine 39. 866 Kazakhstan 40. Kamenicky 41. Mazovia 42. CP 775 43. CRO-ASCII 44. Arabic Farsi 45. Arabic Urdu 46. Greek DEC 47. Greek ELOT 928 1. USA 2. France 3. Germany 4. UK 5. Denmark I 6. Sweden 7. Italy International Character Sets 8. Spain I 9. Japan 10. Norway 11. Denmark II 12. Spain II 13. Latin America 14. Korea 15. Legal 48 Tally Dascom 1225 Line Spacing 1/6", 1/8", n/60", n/180", n/360" Fanfold Paper Cut Sheet Single ply Paper Specifications Multi-part Width: 76.2mm̚419.1mm Width: 76.2mm̚419.1mm (3"̚16.5"˅ ˄3"̚16.5"˅ Length: Length: 101.6mm min (4" min) 101.6mm̚363.2mm Paper Specifications ˄4"̚14.3"˅ Weight: 52̚90g/ Weight: 52̚82 g/ Thickness: Thickness: 0.065̚0.14mm 0.065̚0.14mm (0.0026"̚0.0055”) (0.0026"̚0.0055") Weight: 40̚52g/ Thickness: 0.45 mm max Feeding method: Friction and Tractor Paper Handling Paper path: Cut sheets: Top load and top out Fanfold: Rear in and top out Copy Capability Original + 4 copies Emulation ESC/P2, IBM 2390 Plus Ribbon Type Cartridge; Monochrome Ribbon Life 7 million characters (rolling Draft 10 CPI) Input Data Buffer Up to 48KB Windows Server 2000/2003/2008 Windows Vista Windows Drivers Windows XP Windows 98 Windows 7 Interface Parallel (Bi-directional IEEE-1284 nibble mode) USB 2.0 (B type connector) Operation Panel Noise Level Switches: 5 pcs LED indicators: 10 pcs < 55 dBA in 10CPI draft ASCII (Conforming to ISO7779) 49 (0.0177” max) Tally Dascom 1225 Temperature Operating: Ambient Conditions Humidity +5 to +40 °C. Stand-by: -20 to +55 °C Operating: 10 to 90%RH (No condensation) Stand-by: 10 to 90%RH (No condensation) Dimensions 587 mm (W) x 333 mm (D) x 173 mm (H) Weight 8.5 kg Unit type: Power Supply Switching mode power supply Power cord: Detachable Voltage rating: AC 230V (180V~264V), 50Hz to 60Hz AC 110V/120V, 60Hz (factory option) Stand by: ESD: Less than 7.6W Comply with IEC801-2 Contact discharge: 4kV Air discharge: 8kV Power consumption 38.2 W (Test pattern is specified in standard ISO/IEC 10561.) MTTR < 20 minutes MTBF 10000 hours @ 25% duty cycle Certification CE, UL, FCC, ES, ISTA, RoHS, WEEE, REACH, ChemVerbotsV, Microsoft Certified for Windows 7 50 Tally Dascom 1225 9 Interfaces Parallel Interface Parallel Interface Pin Assignment Pin Signal Name Signal Transmission STROBE ¯¯¯¯¯¯ Printer I Computer 2~9 DATA Printer I Computer 10 ACK ¯¯¯ Printer J Computer 11 BUSY Printer J Computer 12 PE Printer J Computer 13 SELECT Printer J Computer 14 AFXT ¯¯¯¯ Printer I Computer 15 Unused Unused 16 GND Printer Q Computer 17 F-GND Printer Q Computer 18 +5V Printer J Computer 19~30 GND Printer Q Computer 31 ¯¯¯¯ INIT Printer I Computer 32 FAULT ¯¯¯¯¯ Printer J Computer 33 GND Printer Q Computer 34 Unused Unused 35 FUSE Printer J Computer 36 SLCTIN ¯¯¯¯¯¯ Printer I Computer Parallel Interface Connector Diagram Note: Any external devices connected to the parallel port should not draw current exceeding 200 mA from pin 18; otherwise it may affect the printer operation. USB Interface The USB interface conforms to the Universal Serial Bus 2.0 Specifications. It supports the Full Speed mode at 12 Mbps. It uses the “B” type USB connector. 51 Tally Dascom 1225 10 Character sets & Code Pages Character Sets Standard Character Set 1 Standard Character Set 2 52 Tally Dascom 1225 IBM Character Set 1 IBM Character Set 2 53 Tally Dascom 1225 International character sets International Character Set Commands Country USA Command ˘ESC˚“R”CHRˀ˄0˅ France ˘ESC˚“R”CHRˀ˄1˅ Germany ˘ESC˚“R”CHRˀ˄2˅ UK ˘ESC˚“R”CHRˀ˄3˅ Denmark1 ˘ESC˚“R”CHRˀ˄4˅ Sweden ˘ESC˚“R”CHRˀ˄5˅ Italy ˘ESC˚“R”CHRˀ˄6˅ Spain1 ˘ESC˚“R”CHRˀ˄7˅ Japan ˘ESC˚“R”CHRˀ˄8˅ Norway ˘ESC˚“R”CHRˀ˄9˅ Denmark2 ˘ESC˚“R”CHRˀ˄10˅ Spain2 ˘ESC˚“R”CHRˀ˄11˅ Lat America ˘ESC˚“R”CHRˀ˄12˅ Korea ˘ESC˚“R”CHRˀ˄13˅ Legal ˘ESC˚“R”CHRˀ˄64˅ 54 Tally Dascom 1225 Character Tables Italic 55 Tally Dascom 1225 Graphic 1 Graphic 2 56 Tally Dascom 1225 Code Page Commands Code Page ESC R Parameter CRO-ASCII 3C Arabic Farsi 96 Arabic Urdu 97 Greek DEC 46 Greek ELOT 928 6C CP437 Latin US 80 CP737 Greek 93 CP850 Latin 1 82 CP851 Greek 88 CP852 Latin 2 87 CP857 Turkish 8D CP858 (IBM with €) 9E CP860 Portugal 84 CP861 Icelandic 94 CP863 French Canada 85 CP864 Arabic 8C CP864 Arab. Extended 95 CP865 Nordic 86 CP866 Cyrillic 8E CP866 Bulgaria 9D Siemens Turkish 9B DEC Turkish 9C CP1250 Win Latin 2 70 CP1251 Win Cyrillic 71 CP1252 Win Latin 1 72 CP1253 Win Greek 73 CP1254 Win Turkish 74 8859-1 Latin 1 25 8859-1 Latin 1 (SAP) 2B 8859-2 Latin 2 26 8859-5 Cyrillic 2A 8859-7 Greek 2D 8859-9 Turkish 2E 8859-15 Latin 9 (Euro) 2F BRASCII 6D Abicomp 6E Roman 8 4D 57 Tally Dascom 1225 Coax/Twinax(Hebrew) 4F New-437 (Hebrew) 81 New-DIG 850 (Hebr.) 83 Old-Code 860 (Hebr.) 98 Flarro 863 (Hebrew) 99 Table 865 (Hebrew) 9A CP775 Baltic A6 CP1257 Baltic 77 Mazovia (Poland) 92 Kamenicky (Czech) 91 CP866 Ukraine 8F CP866 Kazakhstan 90 58 Tally Dascom 1225 Code Page Tables CP 437 (US) CP 737 Greek 59 Tally Dascom 1225 CP 850 (Multilingual) CP 851 60 Tally Dascom 1225 CP 852 (Eastern Europe) CP 857 (Turkish) 61 Tally Dascom 1225 CP 858 CP 860 (Portugal) 62 Tally Dascom 1225 CP 861 (Iceland) CP 863 (French-Canadian) 63 Tally Dascom 1225 CP 864 Arabic CP 864 Arabic Extended 64 Tally Dascom 1225 CP 865 (Norway) CP 866 (Cyrillic) 65 Tally Dascom 1225 CP 866 Bulgaria CP 1250 Win Latin 2 66 Tally Dascom 1225 CP 1251 Win Cyrillic CP 1252 Win Latin 1 67 Tally Dascom 1225 CP 1253 Win Greek CP 1254 Win Turkish 68 Tally Dascom 1225 8859-1 Latin 1 8859-1 Latin 1 (SAP) 69 Tally Dascom 1225 ISO 8859-2 (ISO Latin 2) ISO 8859-5 Cyrillic 70 Tally Dascom 1225 ISO 8859-7 (Latin/Greek) ISO 8859-9 (Turkish) 71 Tally Dascom 1225 ISO 8859-15 Euro (Code Page 923) BRASCII 72 Tally Dascom 1225 Abicomp Roman 8 73 Tally Dascom 1225 Coax/Twinax (Hebrew) New-437 (Hebrew) 74 Tally Dascom 1225 New-Dig 850 (Hebrew) Old-Code 860 (Hebrew) 75 Tally Dascom 1225 Flarro 863 (Hebrew) 865 Hebrew 76 Tally Dascom 1225 CP 1257 866 Ukraine 77 Tally Dascom 1225 866 Kazakhstan Kamenicky 78 Tally Dascom 1225 Mazovia CP 775 79 Tally Dascom 1225 CRO-ASCII Arabic Farsi 80 Tally Dascom 1225 Arabic Urdu Greek DEC 81 Tally Dascom 1225 Greek ELOT 928 82 Tally Dascom 1225 11 Control Codes Summary Epson Emulation Command List Command Sequence BEL BS HT LF VT FF CR SO SI DC1 DC2 DC3 DC4 CAN DEL ESC SO ESC SI ESC SP n ESC EM n ESC ! n ESC ( - n1 n2 m d1 d2 ESC $ n1 n2 ESC | n ESC % n ESC & ESC ( ^ n m d1 d2… ESC (G NUL d ESC * m n1 n2… ESC . c v h m nL nH d1 d2… ESC + n ESC – n ESC / n ESC ( C NUL n m ESC ( c NUL nt mt nb mb ESC ( U NUL n ESC 0 ESC 2 ESC 3 n ESC 4 ESC 5 ESC 6 ESC 7 Function Beeper Backspace Tab horizontally Line feed Tab vertically Form feed Carriage return Select double-width printing (one line) Select condensed mode Online Cancel condensed mode Offline Cancel double-wide mode(one line) Cancel line Delete character Select double-width printing (one line) Select condensed mode Set intercharacter space NA Print mode setup Choose character lineation Select absolute horizontal print position Set left margin Select user-defined set Define user-defined set Print data in character style Select graphics mode Select image mode Print raster graphics Select n/360Ǝline spacing Underline on/off Select vertical orientation channel Set page length Page setup Set unit Set 1/8Ǝline spacing Set 1/6Ǝline spacing Set n/180Ǝline spacing Set Italic Cancel Italic Enable printable characters Enable upper control characters ESC : Copy ROM to RAM 83 Tally Dascom 1225 ESC ˘ ESC > ESC = ESC # ESC ˛n m ESC @ ESC ˸n1 n2 ESC A n ESC B…NUL ESC C n ESC D…NUL ESC E ESC F ESC G ESC H ESC J n ESC K n1 n2 … ESC L n1 n2 … ESC M ESC N n ESC O ESC P ESC Q n ESC R n ESC S n ESC T ESC U n ESC ( V NUL n m ESC W n ESC X n1 n2 ESC Y n1 n2 … ESC Z n1 n2 … ESC a n ESC b n ESC c n m ESC g ESC j n ESC k n ESC p n ESC q n ESC r n ESC t n ESC (t nL nH d1 d2 d3 ESC ( v NUL n m ESC w n ESC x n ESC( B n1 n2 k m s v1 v2 c Unidirectional mode(1 line) Set MSB to 1 Set MSB to 0 Cancel MSB control Reassign graphics mode Initialize printer Set relative horizontal print position Set n/60Ǝline spacing Set/cancel vertical tabs Set page length in lines Set/cancel horizontal tabs Select Bold Cancel Bold Select double-strike mode Cancel double-strike mode Perform tactic n/180Ǝline feed Select 8 pins single-density graphics Select 8 pins double–density graphics Select ELITE˄12CPI˅ Set bottom margin Cancel bottom margin Select PICA˄10CPI˅ Set right margin International character set Select superscript/subscript Cancel superscript/subscript Select unidirectional/bidirectional printing mode Select absolute vertical print position Turn Double-wide mode on/off Select font by pitch and point Select 8 pins, high speed ,double –density graphics Select 8 pins, high speed fourfold –density graphics Select justification Select vertical orientation channel Set horizontal intercharacter space Select 15CPI Perform reverse n/180Ǝline feed Select typeface Turn proportional mode on/off Select character style Select printing colour Select character table Assign character table Set relative vertical print position Turn double-high mode on/off Select print quality Barcode print 84 Tally Dascom 1225 IBM Emulation Command List Command Sequence BEL BS HT LF VT FF CR SO SI DC1 DC2 DC3 DC4 CAN ESC BEL ESC BS ESC HT ESC CR ESC LF ESC SO ESC SI ESC DC1 ESC DC2 ESC DC3 ESC DC4 ESC CAN ESC FF ESC EM n ESC : ESC VT ESC 0 ESC 1 ESC 2 ESC 3 n ESC 4 ESC 5 n ESC 6 ESC 7 ESC = ESC \ ESC ^ ESC A n ESC B n ESC C n Function Beeper Backspace Tab horizontally Line feed Tab vertically Form feed Enter Select double-wide mode Select condensed mode Online Select 10CPI Offline Cancel double-wide mode(one line) Cancel buffer Beeper Backspace Tab horizontally Enter Line feed Select double-wide mode Select condensed mode Online Select 10CPI Offline Cancel double-wide mode(one line) Cancel buffer Form feed Automatically Feed Paper mode Set 12CPI Tab vertically Select 1/8Ǝline spacing Select 7/72Ǝline spacing Select 1/6Ǝline spacing or activate ESC A n command Select n/216Ǝor 1/180Ǝline spacing Set top margin Automatic Line Feed Select character set 2 Select character set 1 NA Print continuously from all character chart Print single character from all character chart Select n/72Ǝor n/60Ǝline spacing Select Tab vertically Set page length in lines 85 Tally Dascom 1225 ESC C NUL n ESC D ESC E ESC F ESC G ESC H ESC I n ESC J n ESC K n1 n2 V1 V2 …Vn ESC L n1 n2 V1 V2 …Vn ESC N n ESC O ESC P n ESC Q n ESC R ESC S n ESC T ESC U n ESC W n ESC X n m ESC Y n1 n2 V1 V2 …Vn ESC Z n1 n2 V1 V2 …Vn ESC [- n1 n2 m1 m2 ESC [@ n1 n2 m1 m2 m3 m4 ESC [I n1 n2 Hf Ls Hs Lf Sm NUL Hc Lc ESC [ K n1 n2 init id para1 para2 …paran ESC [ T n1 n2 n3 n4 Hc Lc ESC [\ ESC [d ESC [f n1 n2 k m s v1 v2c ESC [g n1 n2 m ESC [p n1 n2 ESC ] ESC_ n ESC- n ESC d n m ESC j ESC r n ESC * m Set page length in inches Select Tab horizontally Select bold Cancel bold Select double-strike mode Cancel double-strike mode Select printing mode Perform n/180Ǝor n/216Ǝsingle line feed Normal density graphics Dual-Density Bit Image Graphics (Half Speed) Select bottom margin Cancel bottom margin Set proportional intercharacter Offline Clear tab Select superscript/subscript Cancel superscript/subscript Select bidirectional printing on/off Select double-wide printing mode(continuous) Set left and right margin Select double -density graphics Select fourfold -density graphics Select line Select printing mode Select font and pitch Set initialization condition Set code page Set vertical unit Select printing quality Set barcode parameters Select high-density graphics printing Set barcode data Feed paper in reverse direction Print upper-line Print underline Move the current printing position Stop printing Select printing colour Select graphic mode If you need more details regarding the emulation commands, please contact us. 86 Tally Dascom 1225 FCC STATEMENT 1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: a. This device may not cause harmful interference. b. This device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Re-orientate or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. 87 DASCOM REPRESENTATIVES GERMANY DASCOM Europe GmbH Heuweg 3 D-89079 Ulm Deutschland Tel.: +49 (0) 731 2075 0 Fax: +49 (0) 731 2075 100 www.dascom.com SINGAPORE (ASIA PACIFIC) DASCOM AP Pte Ltd 21 Bukit Batok Crescent #29-81, WCEGA Tower Singapore 658065 Phone: +65 6760 8833 Fax: +65 6760 1066 www.dascom.com AMERICAS DASCOM Americas Corporation 421 W. Main Street, Waynesboro, VA 22980 USA Phone:+1 (877) 434 13 77 www.dascom.com UNITED KINGDOM DASCOM GB Ltd Hart House, Priestley Road Basingstoke, Hampshire RG24 9PU, England Phone: +44 (0) 1256 481481 Fax: +44 (0) 1256 481400 www.dascom.com FRANCE DASCOM Europe GmbH 117 Avenue Victor Hugo 92100 Boulogne-Billancourt France Phone: +33 (1) 73 02 51 98 www.dascom.com CHINA Jiangmen Dascom Computer Peripherals Co.,Ltd. No.399, Jinxing Road, Jianghai District, Jiangmen City, Guangdong Province, P.R.China www.dascom.com “All rights reserved. Translations, reprinting or copying by any means of this manual complete or in part or in any different form requires our explicit approval. We reserve the right to make changes to this manual without notice. All care has been taken to ensure accuracy of information contained in this manual. However, we cannot accept responsibility for any errors or damages resulting from errors or inaccuracies of information herein.” © 2011 DASCOM Part No: 21.511.801.0043
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : Yes XMP Toolkit : 3.1-701 Keywords : Producer : Acrobat Distiller 7.0.5 (Windows) Company : DASCOM Create Date : 2014:02:27 21:00:52+08:00 Modify Date : 2014:02:27 21:00:52+08:00 Metadata Date : 2014:02:27 21:00:49+08:00 Creator Tool : PScript5.dll Version 5.2 Document ID : uuid:F7F1392EAF9FE311A3B1ADE24A44160F Instance ID : uuid:13641c23-4d17-4e7d-8e0f-6e4437374358 Derived From Instance ID : uuid:e7feeafd-4413-440a-9607-fb0323b2bb0c Derived From Document ID : uuid:f0e07d16-256e-4a2d-9b24-c0c8481f2f0b Format : application/postscript Creator : Administrator Title : Description : Page Count : 104 Subject : Author : AdministratorEXIF Metadata provided by EXIF.tools