Jiangmen Dascom Computer Peripherals TD5130P Dot Matrix Printer User Manual UG 5130T preliminary tv04
Jiangmen Dascom Computer Peripherals Co.,Ltd. Dot Matrix Printer UG 5130T preliminary tv04
user manual
Tally Dascom 5130P Important Safety Instructions (English) Read the following instructions thoroughly before starting up your printer. • Never carry out maintenance or repair work yourself. Always contact a qualified service technician. • Keep this Operator’s Manual in a place which is easily accessibleat all times. • Place the printer on a solid and even base so that it cannot fall. • Never place the printer in the vicinity of inflammable gas or explosive substances. • Ensure the printer is connected to a socket with the correct mainsvoltage. • Alwaysdisconnect the printer from the mainsbefore opening the device to perform maintenance work or remedy errors. • Do not expose the printer to high temperatures, direct sunlight or dust. • Keep all liquids away from the printer. • Protect the printer from shock, impact and vibration. • Make sure that the printer and computer are switched off before connecting the data cable. • The print head will become very hot during printing; avoid contact with the print head after printing has finished. • Do not perform any operation or action in any way other than those provided in this manual. When in doubt, contact your dealer or your customer support. Tally Dascom 5130P Wichtige Sicherheitshinweise (German) Lesen Sie bitte diese Sicherheitshinweise durch, bevor sie den Drucker in Betrieb nehmen. • Führen Sie Wartungsarbeiten und Reparaturen keinesfalls selbst aus, sondern verständigen Sie immer einen qualifizierten Servicetechniker. • Bewahren Sie diese Dokumentation an einem jederzeit zugänglichen Ort auf. • Den Drucker auf stabilem und ebenem Untergrund so aufstellen, dass er nicht zu Boden fallen kann. • Stellen Sie den Drucker keinesfalls in der Nähe von leicht entzündlichen Gasen oder explosiven Stoffen auf. • Den Drucker nur an eine Steckdose mit der richtigen Spannung anschließen. • Wenn Sie den Drucker vom Netz trennen wollen, den Drucker ausschalten und immer den Netzstecker an der Steckdose ziehen. • Den Drucker weder hohen Temperaturen noch direktem Sonnenlicht und Staub aussetzen. • Keine Flüssigkeiten mit dem Drucker in Berührung bringen. • Den Drucker keinen Erschütterungen, Stößen oder Vibrationen aussetzen. • Sicherstellen, dass der Drucker und der Computer ausgeschaltet sind, bevor das Datenkabel angeschlossen wird. • Der Druckkopf wird während des Druckens heiß. Vor dem Berühren deshalbeinige Zeit abkühlen lassen. • Weichen Sie bei der Bedienung des Druckers nicht von den Anweisungen in der Dokumentation ab. Bei Unklarheiten wenden Sie sich bitte an Ihren Händler oder Ihren Kundendienst. II Tally Dascom 5130P Consignes importantes de sécurité (French) Lire attentivement les instructions suivantes avant de mettre l’imprimante en service. • Ne jamais effectuer soi-même les travaux d’entretien et de réparations. Contacter toujours un dépanneur qualifié. • Placer l’imprimante sur un support stable de façon à ce qu’elle ne puisse pas tomber. • Ne jamais placer l’imprimante à proximité de sources de gaz aisément inflammables ou de substances explosives. • Ne connecter l’imprimante à une prise que lorsque la tension est correcte. • Pour déconnecter l’imprimante de l’alimentation principale, mettre l’imprimante hors tension et toujours débrancher le connecteur secteur de la prise murale. • Ne pas exposer l’imprimante à des températures élevées, à la lumière directe du soleil ou à la poussière. • Ne pas mettre l’imprimante en contact avec des liquides. • Ne pas exposer l’imprimante à des chocs, impacts ou vibrations. • S’assurer que l’imprimante et l’ordinateur sont hors tension avant de connecter le câble de données. • La tête d’impression est brûlante pendant l’impression. C’est pourquoi laissez-la refroidir quelques instants avant d’y toucher. • N'exécutez aucune opération ni action d'une autre manière que celle indiquée dans ce manuel.En cas de doute, veuillezcontacter votre distributeur ou service après-vente. III Tally Dascom 5130P Indicazioni di sicurezzaimportanti (Italian) Prima di mettere in funzione la stampante, leggere attentamente le seguenti indicazioni. Non eseguire mai da sé gli interventi di manutenzione e riparazione, ma rivolgersi sempre a un tecnico di assistenza qualificato. • Conservare le presenti istruzioni per l’uso in un luogo sempre accessibile. • Collocare la stampante su una superficie stabile, per evitare che cada a terra. • Non collocare la stampante in prossimità di gas facilmente infiammabili o di sostanze esplosive. • Collegare la stampante a una presa di corrente con tensione adeguata. • Per scollegare la stampante dalla rete di alimentazione, spegnerela stampante e disinserire sempre il connettoredi rete dalla presa. • Non esporre la stampante ad elevate temperature né alla luce solare diretta e alla polvere. • Evitare il contatto della stampante con liquidi. • Non esporre la stampante a colpi, scosse o vibrazioni. • Verificare che la stampante e il computer siano spenti primadi collegare il cavo di trasmissione dati. • Durante la stampa, la testina si surriscal-da notevolmente. Prima di toccarla, se necessarioopportuno quindi lasciarla raffreddare qualche istante. • Non eseguire alcuna operazione o azione se non nella maniera descritta nel presente manuale. In caso di dubbio, contattare il rivenditore o dalla società incaricata dell’assistenza. IV Tally Dascom 5130P Instrucciones de seguridad importantes (Spanish) Lea las siguientes instrucciones con esmero antes de poner la impresora en servicio. Nuncalleve a cabo trabajos de mantenimiento o reparación Ud. mismo,sino consultea un técnico de servicio calificado. • Guarde las presentes instrucciones de servicio en un lugar de fácil acceso en cualquier momento. • Ponga la impresora sobre un base estable de manera que no pueda caer al suelo. • Nunca coloquela impresora en la vecindad de gases de fácil inflamabilidad o sunstancias explosivas. • Asegure conectar la impresora sólo a un enchufe con un voltajecorrecto. • Cuando quiera desconectar la impresora de la red, apague la impresora y siempre tire la clavija de alimentación del enchufe. • No exponga la impresora a temperaturas altas, a la luz solar directa y al polvo. • No pongala impresora en contacto con fluidos. • Nunca exponga la impresora a sacudidas, choques o vibraciones. • Asegúrese de que la impresora y el ordenador estén apagdos antes de conectar el cable de datos. • La cabeza de impresión se pone muy caliente durante la impresión. Por lo tanto, deje enfriarlo algún tiempo antes de tocarla. • No permita que se realice cualquier operación o acción de una forma diferente a lo que se señala en el manual. En caso de duda, póngase en contacto con su comerciante o con su servicio post-venta. Tally Dascom 5130P Правила по технике безопасности. (Russian) Прочитайте, пожалуйста, инструкцию по технике безопасности перед включением в работу принтера. • Не выполняйте технические работы и ремонт техники самостоятельно, но сообщайте о неисправностях квалифицированным сервисным техникам. • Данная инструкция должна быть всегда доступна каждому пользователю. • Установите принтер на ровном и стабильном месте так, чтобы он не смог упасть на пол. • Ни в коем случае не ставьте принтер вблизи легко воспламеняющихся газов и взрывчатых веществ. • Включайте принтер в розетку только с соответствующим напряжением. • Если Вы хотите отключить принтер от напряжения, сначала выключите принтер сам и затем выньте штекер из розетки. • Берегите принтер от нагревания, от попадания на него прямых солнечных лучей и пыли. • Не допускайте попадания жидкости на принтер. • Нельзя подвергать принтер тряске, ударам и вибрации. • Убедитесь, что принтер и компьютер выключены, только после этого соедините принтер с компьютером. • Печатающая головка нагревается во время работы принтера. Поэтому подождите какое-то время, прежде чем дотронуться до нее. • Пользуйтесь принтером так, как это написано в документации. Если у Вас возникают неясности, обращайтесь с вопросами к Вашим продавцам или в сервисный центр. VI Tally Dascom 5130P InstruçõesImportantes sobre Segurança (Portuguese) Leia as instruções de segurança antes de usar a impressora. • Consultesempre um técnico qualificado para executar uma reparação . • Coloquea impressora sobre uma base sólida e nivelada, para que ela não sofra quedas. • Jamais instale a impressora nas proximidades de lugares onde haja gás inflamável ou substâncias explosivas. • Assegure-se de conectar a impressora à tomada elétrica com a voltagem apro-priada. • Quando desligar a impressora da rede, desligue sempre a impressora e retire o cabo da tomada. • Não exponha a impressora a temperaturas altas ou luz solar direta. • Não aproxime substâncias líquidas da impressora. • Proteja a impressora de choques, impactos e vibrações. • Desligue a impressora e o computador antes de conectar o cabo da rede. • A cabeça da impressora pode ficar muito quente . Portanto, espere algum tempo antes de tocá-la. • Não faça nenhuma operação ou ação além das recomendadas neste manual. Em caso de dúvida, contate seu revendedor ou companhia de serviço. VII Tally Dascom 5130P Önemli Güvenlik Talimatları (Turkish) Lütfen, yazıcıyı işletime geçirmeden önce bu güvenlik talimatlarını bütünüyle dikkatle okuyun. • Bakım ve tamir çalışmalarını kesinlikle ve hiçbir surette kendi başınıza yapmayın; her zaman kalifiyebir uzman servis-teknisyenine haber verin. • Yazıcıyı, üzerinden yere düşmesi mümkün olmayacak sabit ve düz bir zemine yerleştirin. • Yazıcıyı kesinlikle ve hiçbir surette kolayca yanabilecek gaz veya patlayıcı maddeler içeren nesnelerin yakınına koymayın. • Yazıcı akım kablosunu sadece doğru gerilime sahip bir prize takın. • Yazıcıyı şebeke ağından ayırmak istediğinizde, yazıcıyı kapatın ve ağ-fişini her zaman prizden çıkartın. • Yazıcıyı ne yüksek ısılı ne de doğrudan güneş ışığına ve toza mâruz kalan mekânlarda bulundurun. • Yazıcı hiçbir sıvı maddeyle temasta olmamalıdır. • Yazıcı hiçbir sarsıntıya, darbeye veya titreşime mâruz kalmamalıdır. • Veri kablosu bağlanmadan önce hem yazıcının hem de bilgisayarın kapalıolduklarından emin olmalısınız. • Yazıcının başı basma esnasında yüksek ısıya ulaşıyor. Bu yüzden lütfen dokunmadan önce kısa süre soğumasını bekleyin. • Yazıcının işletimi ve kullanımında bu dokümantasyondaki talimatların hiç dışına çıkmayın. Sorunlu görünen hususlarda lütfen imâlatçınıza veya müşteri hizmetleri servisinize başvurun. VIII Tally Dascom 5130P TRADEMARK ACKNOWLEDGEMENTS “IBM” is a trademark of International Business Machines Corporation. “EPSON” is a trademark of Epson America Incorporated. “DEC” is a trademark of DigitalEquipment Corporation. “Centronics” is a trademark of Centronics Data Computer Corporation. “DOS” is a trademark of Microsoft Corporation. “SAP” is a trademark of SAP AG. “Windows”, “Windows 7”, “Windows 95”, “Windows 98“, “Windows NT”, “Windows 2000”, “Windows 2003/2008 Server”, “WindowsXP” and “Windows Vista” are trademarks of Microsoft Corporation. All other product names and company names appearing in this manual are the registered trademarks or trademarks of the individual companies. IX Tally Dascom 5130P Tally Dascom 5130P TABLE OF CONTENTS 1 UNPACKING GUIDE ........................................................................................................................................ 1 PREPARE THE PRINTER ......................................................................................................................................... 2 TRACTOR INSTALLATION ........................................................................................................................................ 3 PLACING THE PRINTER.......................................................................................................................................... 5 PRINTER COMPONENTS ........................................................................................................................................ 6 2 SETTING UP PRINTER .................................................................................................................................... 7 INSTALLRIBBON .................................................................................................................................................. 7 CONNECTING THE INTERFACE CABLE .................................................................................................................... 10 CONNECTING THE MAINS POWER ........................................................................................................................ 11 INSTALLING THE WINDOWS DRIVER...................................................................................................................... 12 3 PAPER INSTALLATION GUIDE..................................................................................................................... 16 PAPER AND PRINTABLE AREA SPECIFICATION ........................................................................................................ 16 INSERTING A CUT SHEET ..................................................................................................................................... 19 INSERTING A PASSBOOK...................................................................................................................................... 20 TRACTOR FEED HANDLING .................................................................................................................................. 20 4 CONTROL PANEL OPERATION .................................................................................................................... 21 OPERATING ....................................................................................................................................................... 21 LED AND SWITCH STATUS .................................................................................................................................. 22 FAILURE INDICATIONS ......................................................................................................................................... 24 POWER ON FUNCTIONS ..................................................................................................................................... 25 HEX DUMP ....................................................................................................................................................... 26 SETUP MENU .................................................................................................................................................... 27 CHANGE CONFIGURATIONS ................................................................................................................................. 28 MENU CONFIGURATION (SAMPLE) ....................................................................................................................... 29 5 DEFAULT SETTINGS..................................................................................................................................... 30 SYSTEMSETUP .................................................................................................................................................. 30 INTERFACE SETUP.............................................................................................................................................. 30 CHARACTER SETUP ............................................................................................................................................ 30 EMULATIONSETUP ............................................................................................................................................ 32 RESTORE FACTORY DEFAULT ............................................................................................................................... 32 6 MAINTENANCE ............................................................................................................................................. 33 CLEANING ......................................................................................................................................................... 33 CLEANINGAND VACUUMING THE PRINTER .............................................................................................................33 7 TROUBLESHOOTING .................................................................................................................................... 34 PRINT QUALITY PROBLEMS AND SOLUTIONS ........................................................................................................ 34 PAPER HANDLINGPROBLEMS AND SOLUTIONS ..................................................................................................... 35 OPERATINGPROBLEMS AND SOLUTIONS .............................................................................................................. 35 XI Tally Dascom 5130P ERROR INDICATIONS ON LEDS ............................................................................................................................ 36 DIAGNOSTIC FUNCTIONS.................................................................................................................................... 37 FIRMWARE UPDATE ........................................................................................................................................... 38 8 SPECIFICATION ............................................................................................................................................. 39 9 INTERFACES .................................................................................................................................................. 44 PARALLEL INTERFACE ......................................................................................................................................... 44 USB INTERFACE ................................................................................................................................................ 44 SERIAL INTERFACE ............................................................................................................................................. 44 10 CHARACTER SETS & CODE PAGES .......................................................................................................... 45 CHARACTER SETS.............................................................................................................................................. 45 INTERNATIONAL CHARACTER SETS ........................................................................................................................ 47 INTERNATIONAL CHARACTER SET COMMANDS ...................................................................................................... 47 CHARACTER TABLES ........................................................................................................................................... 48 CODE PAGE COMMANDS .................................................................................................................................... 50 CODE PAGE TABLES ........................................................................................................................................... 52 11 CONTROL CODES SUMMARY ................................................................................................................... 76 EPSON EMULATIONCOMMAND LIST....................................................................................................................76 IBM EMULATIONCOMMAND LIST ....................................................................................................................... 78 XII Tally Dascom 5130P 1 Unpacking Guide • Place your packagedprinter on a solid base. • Make sure that the “Up” symbols point in the correct direction. • Open the packaging, lift the printer out of the cardboard box and remove the remaining packaging material. • Check the printer for any visible transport damage and missing items. If you find any transport damage or if any accessories are missing,please contact your dealer. The following items should be included: Printer Tractor pair assembly (for Tractor version) Power cord Ribboncartridge CD-ROM Installation Guide Tally Dascom 5130P Preparethe Printer Remove the packaging materials from the printer as follows: 1-2: Remove all the visible tape from the outsideof the printer. 3: Open the printer front cover. 4: Remove the transparent cover. 5: Remove the cable ties from the left and right ends of the carriage shaft. 6: Remove the shipping cardboard from around the print head. 7-13: Remove the shipping foams from around the chassis. 14: Install back the transparent cover. 15: Remove the shipping cardboard from the printer rear. 16: Install the tractor pair assembly (for Tractor version). Tally Dascom 5130P Tractor Pair Installation If you want to use continuous fanfold paper, you have to install the tractor pair assembly. Before installing the tractor pair assembly, the printer rear cover must be removed first. Below instructions show how to install and remove both the printer rear cover and tractor pair assembly. Removing and installing the printer rear cover: 1. Ensure there is no loaded paper in the printer. Switch off the printer. 2. Open the printer top cover, move the print head with care to the left. Attention: The print head could be very hot if printing had just been performed, so be careful when touching the print head. 3. Use a flathead screwdriver or similar tool to insert into the latches at “4” and “5”, apply downward pressure to release the lock. Remove the rear cover “6” from the back of the printer. Close the printer top cover. 4. Installing the printer rear cover is the reverse of the removal process. First, align the latches of the rear cover at the back of the printer. Next, use your thumbs to press the rear cover steadily and firmly towards the printer. The “4” and “5” latches should snap on. When the installation is done correctly, the rear cover should be flat againstthe back of the printer. Tally Dascom 5130P Installing and removing the tractor pair assembly: 1. To install, first insert the upper cylindrical fingers at both ends of the tractor assembly into the metal frame at the back of the printer (see picture “7”). Tilt the tractor assembly downwards, and use your index fingers to push the lower cylindrical fingers at both ends slightly upwards until they are mounted at the bottom of the printer metal frame (see picture “8”). 2. To remove, use your fingers to grip both ends of the tractor assembly, tilt up and pull to release it from the printer metal frame. Tally Dascom 5130P Placing the Printer Place the printer on a solid, flat, stable surface; ensuring that the printer is positioned in such a way that it cannot move, and that there is easy access to the control panel and paper input devices. Also ensure that there is enoughspace for sufficient ventilation and for the printed output. When selecting the printer location, observe the following additional instructions: • Never place the printer near to any flammable gas or explosive substances. • Do not expose the printer to direct sunlight. If you cannot avoid placing the printer near a window, protect it from the sunlight with a curtain. • When connecting a computer to the printer, make sure the maximum recommended cable length is not exceeded. • Ensure sufficient distance between the printer and any heating devices/radiators. • Avoidexposing the printer to extreme temperature or air humidity fluctuations. Avoidexposureto dusty environments. • It is recommended the printer is installed in a position which reduces noise exposure to the work place during printing. Tally Dascom 5130P Printer Components Component Function Control Lever Lift up the top of mechanism to install or remove ribbon Paper Loader Paper feed path for single sheet and passbook. Print Head 24-pin printing mechanism Cover Protects print head and other components inside, and reduces noise. Control panel Shows printer status, and for printer setup Power switch Power printer ON or OFF Ribboncartridge Contains the ink to print on the media Ribbonguides For guiding ribbon installation on print head Power receptacle Connects power cord to the printer Serial interface Connects serial interface cable from the host Parallel interface Connects parallel interfacecable from the host USB interface Connects USB interface cable from the host Tally Dascom 5130P 2 Setting Up Printer InstallRibbon 1. Ensure the power to the printer is off. 2. Press the recesses of both sides to open the cover. Remove the transparent cover. 3. Push the control lever to lift up the top of mechanism, and make sure the control lever is set to the latched position. 4. Move the print head to the center of the carriage. Tally Dascom 5130P 5. Install the recess positions on the ribbon cartridge into the printer mounting, and push both sides of the ribbon cartridge to ensure they click into position. 6. Press the ribbon guides onto the print head from underneath until they click into position. 7. Turn the ribbon knob until the ribbon fabric is taut. Move the carriage left and right to ensure the carriage and ribbon fabric can move smoothly. Tally Dascom 5130P 8. Pull down the control lever to set the top of mechanism to its original position, and make sure the control lever is fully latched. 9. Install back the transparent cover to reduce noise. 10. Close the cover carefully. When the printer is in operation, ensure the cover is closed to keep the dust away and minimize the noise level. Open the cover only for cleaning, clear paper jam or ribbon replacement. Tally Dascom 5130P Notes on RibbonCartridge Removal: 1. 2. 3. 4. Eject any paper loaded in the printer. Turn off the printer power. Open the front cover. Move the carriage to the middle. Be careful not to touch the print head if printing had just been performed, as the print head may be hot. 5. Remove the blue ribbon guides from the print head. 6. Use fingers to take hold of the ribbon cartridge firmly, and pull the cartridge towards you to unlatch it. 7. Remove the ribbon fabric from the print head carefully without entangling it. Connecting the Interface Cable The parallel, serial and USB interface ports are located at the rear of the printer. Choose the interface which suits your system. IMPORTANT: Make sure the printer and the computer are switched off before connecting or disconnecting the interfacecable to prevent electrical damage to the interfaceports. USB Interface Parallel Interface Serial Interface 10 Tally Dascom 5130P Connecting the Mains Power Checkingthe printer voltage Make sure that the device has been set according to your country’s power supply voltage.To do this, check the ratingplate at the back of the printer. Contact your dealer if the setting is incorrect. Never switch on the printer if the voltage setting is incorrect; this may result in electrical damage to the printer. 1. Make sure the printer and the computer are powered off. 2. Connect the power cord to the power receptacleat the back of the printer, as shown as below. Ensure the power cord is securely connected. Connect the power cord plug to a mains socket. 3. Press the power switch to the “I” position to power on the printer. Upon power-on, all the five LEDs light up briefly. After initialization, only the “ON” LED should light up. 4. Press the power switch to the “O” position if you wish to switch off the printer. NOTE: • After switching off the printer, wait at least 5 seconds before switching on again. Otherwise, it may cause damage to the printer. • Disconnect the power cord if the printer is not used for a long time. 11 Tally Dascom 5130P Installing the Windows Driver (Compatible with Windows 2000/2003/2008 Server/XP/Vista/7) 1. Your printer CDROM comes with Windows drivers. Go to the Drivers folder and run the Installer “DriverSetup.exe”. You will see the screen below. Click “Next” to continue. 2. A list of ports available on your system will be displayed as shown below. Choose the desired port to use. Click “Next” to continue. 12 Tally Dascom 5130P 3. Select the desired printer model as shown below. Click “Next” to continue.Cancel 4. Here you can choose whether to set the driver as the system default driver, and whether you want to print the Test Page after installation is completed. If the driver had been installed before, it would be listed in the white box below. Select the listed driver (if any) if you want to replace it; otherwise a copy of the driver will be installed. Click “Next” to continue. 13 Tally Dascom 5130P 5. Click “Finish” to start the installation process. .motPRN Note: Do not interrupt the downloading process to prevent possible flash memory corruption. 5. When downloading is completed,the carriage returns to home position. Printer initializes normally. 38 Tally Dascom 5130P 8 Specification Print System Monochrome serial impact dot matrix Print Technology Uni-/bi-directional logic seeking for text and graphics Pitch HS Draft* Draft HS-LQ (CPS/DPI) 10 CPI 400 CPS 300 CPS 200 CPS 100 CPS 360 CPS 240 CPS 120 CPS 12 CPI Print Speed 15 CPI 17.1 CPI 20 CPI *limited print width of 8.4inch Font Matrix Print Head Graphics Pitch HS Draft Draft HS-LQ (Matrix/DPI) 10 CPI 8x8/80H 12x24/120H 18x24/180H 36x24/360H 12 CPI 10x24/120H 15x24/180H 30x24/360H 15 CPI 8x16/120H 24x12/180H 24x16/360H 17.1 CPI 10.5x24/180H 21x24/360H 20 CPI 9x24/360H 18x24/360H Proportional Nx24/360H Nx24/360H Number of pins: 24 pins Firing frequency: Normal mode: 1800 Hz Pin diameter: 0.25 mm Life: 400 million strokes/pin@ Draft mode Horizontal: 1/60, 1/72, 1/80, 1/90, 1/120, 1/180, 1/216, 1/360 Vertical: 1/180, 1/360 Paper Feed Speed Form Feed: 18 IPS (Inches per second) Continuous FormFeed: 15 IPS (inches per second) Resolution 360 x 360 DPI maximum Characters per inch (CPI); Characters per line (CPL) Tractor: 10 CPI: Printable Columns Friction: 82 CPL 10 CPI: 94 CPL 12 CPI: 94 CPL 12 CPI: 112 CPL 15 CPI: 123 CPL 15 CPI: 141 CPL 17.1 CPI: 140 CPL 17.1 CPI: 161 CPL 20 CPI: 164 CPL 20 CPI: 188 CPL 24 CPI: 225 CPL 39 Tally Dascom 5130P Bitmap Fonts: Draft 10, 12, 15, 17.1, 20, 24 CPI Roman 10, 12, 15, 17.1, 20 CPI, Proportional Built-In Fonts OCR-B 10 CPI in NLQ and LQ; 12, 17.1, 20 CPI, Proportional OCR-A 10 CPI in NLQ and LQ, 12, 17.1, 20 CPI, Proportional Courier,Gothic, SanSerif, Prestige elite, Script, Orator, bold all in NLQ and LQ style and 10, 12, 15, 17.1, 20 CPI, Proportional (via programming) 1. EAN-13 2. EAN-8 3. Interleaved 2 of 5 4. UPC-A Barcodes 5. UPC-E 6. Code 39 7. Code 128 8. POSTNET 9. Codabar 10. Industrial 2 of 5 1. CP 437 2. CP 737 3. CP 850 4. CP 851 5. CP 852 6. CP 857 7. CP 858 8. CP 860 9. CP 861 Code Pages 10. CP 863 11. CP 864 12. CP 864 Extended 13. CP 865 14. CP 866 Cyrillic 15. CP 866 Bulgaria 16. CP 1250 17. CP 1251 18. CP 1252 19. CP 1253 40 Tally Dascom 5130P 20. CP 1254 21. 8859-1 22. 8859-1 (SAP) 23. 8859-2 24. 8859-5 25. 8859-7 26. 8859-9 27. 8859-15 28. BRASCII 29. Abicomp 30. Roman8 31. Coax/Twinax Code Pages 32. New-437 33. New-Dig 850 34. Old-Code 860 35. Flarro 863 36. 865 Hebrew 37. CP 1257 38. 866 Ukraine 39. 866 Kazakhstan 40. Kamenicky 41. Mazovia 42. Siemens Turk. 43. DEC Turkish 44. CP 775 Baltic 45. CRO-ASCII 46. Arabic Farsi 47. Arabic Urdu 48. Greek DEC 49. Greek ELOT 928 41 Tally Dascom 5130P 1. USA 2. France 3. Germany 4. UK 5. Denmark I 6. Sweden 7. Italy International Character Sets 8. Spain I 9. Japan 10. Norway 11. Denmark II 12. Spain II 13. Latin America 14. Korea 15. Legal Cut Sheet Width: 60 – 245 mm Length: 67 – 363.2 mm Weigth: 52 – 157 g/m² Thickness: 0.0. – 0.12 mm Paper Specifications Continuous Form Width: 101.6 – 241.3 mm Length: 139.7 mm and above Weight: 64 – 100 g/mm² Thickness: 0.06 – 0.35 mm Width: Bankbook 105 – 241 mm Length: 67 – 363.2 mm Weight: 95 – 116 g/m² Thickness: 0.06 – 2.8 mm (P: 6.0 mm) Feeding method: Friction and Tractor Paper Handling Paper path: Cut sheets, Bankbook:Front in, front or rear out Continuous Forms: Rear in, front out Copy Capability Original + 4 copies Emulation ESC/P2, IBM X24 Ribbon Type Cartridge; Monochrome Ribbon Life 4 million characters @ 10 CPI Draft Input Data Buffer 96 KB 42 Tally Dascom 5130P Windows Server 2000/2003/2008 Windows Drivers Windows Vista Windows XP Windows 98 Windows 7 Interface Parallel (Bi-directional IEEE-1284 nibble mode) RS232C (9-pin Sub-D male IF) USB 2.0 (B type connector) Operation Panel Switches: 3 pcs Noise Level Less then < 55 dBA, Draft Mode (ISO7779 pattern) LED indicators: 5 pcs Temperature Operating: Ambient Conditions Humidity +5 to +40 °C. Stand-by: -20 to +60 °C Operating: 10 to 90%RH (No condensation) Stand-by: 5 to 95%RH (No condensation) Dimensions 384 mm (W) x 313 mm (D) x 203 mm (H) Weight 9 kg Power Supply Power cord: Detachable Voltage rating: AC 230V (180V~264V), 50Hz to 60Hz AC 110V/120V, 60Hz (factory option) Stand by: 7W ESD: Comply with IEC801-2 Contact discharge: 4kV Air discharge: Certification 8kV CE, UL, FCC, ES, ISTA, RoHS, WEEE, REACH, ChemVerbotsV, 43 Tally Dascom 5130P 9 Interfaces Parallel Interface Parallel Interface Pin Assignment Pin Signal Name Signal Transmission STROBE,¯¯¯¯¯¯ Printer I Computer 2~9 DATA Printer I Computer 10 ACK,¯¯¯ Printer J Computer 11 BUSY Printer J Computer 12 PE Printer J Computer 13 SELECT Printer J Computer 14 AFXT,¯¯¯¯ Printer I Computer 15 Unused Unused 16 GND Printer Q Computer 17 F-GND Printer Q Computer 18 +5V Printer J Computer 19~30 GND Printer Q Computer 31 INIT,¯¯¯¯ Printer I Computer 32 FAULT,¯¯¯¯¯ Printer J Computer 33 GND Printer Q Computer 34 Unused Unused 35 FUSE Printer J Computer 36 SLCTIN,¯¯¯¯¯¯ Printer I Computer Parallel Interface Connector Diagram Note: Any external devices connectedto the parallel port should not draw current exceeding 200 mA from pin 18; otherwise it may affect the printer operation. USB Interface The USB interface conforms to the Universal Serial Bus 2.0 Specifications. It supports the Full Speed mode at 12 Mbps. It uses the “B” type USB connector. Serial Interface RS232C (9-pin Sub-D male Interface) 44 Tally Dascom 5130P 10 Character sets & Code Pages Character Sets Standard Character Set 1 Standard Character Set 2 45 Tally Dascom 5130P IBM Character Set 1 IBM Character Set 2 46 Tally Dascom 5130P International character sets International Character Set Commands Country USA France Germany UK Denmark1 Sweden Italy Spain1 Japan Command <ESC>“R”CHR$(0) <ESC>“R”CHR$(1) <ESC>“R”CHR$(2) <ESC>“R”CHR$(3) <ESC>“R”CHR$(4) <ESC>“R”CHR$(5) <ESC>“R”CHR$(6) <ESC>“R”CHR$(7) <ESC>“R”CHR$(8) 47 Tally Dascom 5130P Norway Denmark2 Spain2 Lat America Korea Legal <ESC>“R”CHR$(9) <ESC>“R”CHR$(10) <ESC>“R”CHR$(11) <ESC>“R”CHR$(12) <ESC>“R”CHR$(13) <ESC>“R”CHR$(64) Character Tables Italic 48 Tally Dascom 5130P Graphic 1 Graphic 2 49 Tally Dascom 5130P Code Page Commands Code Page ESC R Parameter CRO-ASCII 3C Arabic Farsi 96 Arabic Urdu 97 Greek DEC 46 Greek ELOT 928 6C CP437 Latin US 80 CP737 Greek 93 CP850 Latin 1 82 CP851 Greek 88 CP852 Latin 2 87 CP857 Turkish 8D CP858 (IBM with €) 9E CP860 Portugal 84 CP861 Icelandic 94 CP863 French Canada 85 CP864 Arabic 8C CP864 Arab. Extended 95 CP865 Nordic 86 CP866 Cyrillic 8E CP866 Bulgaria 9D Siemens Turkish 9B DEC Turkish 9C CP1250 Win Latin 2 70 CP1251 Win Cyrillic 71 CP1252 Win Latin 1 72 CP1253 Win Greek 73 CP1254 Win Turkish 74 8859-1 Latin 1 25 8859-1 Latin 1 (SAP) 2B 8859-2 Latin 2 26 8859-5 Cyrillic 2A 8859-7 Greek 2D 8859-9 Turkish 2E 8859-15 Latin 9 (Euro) 2F BRASCII 6D Abicomp 6E Roman 8 4D 50 Tally Dascom 5130P Coax/Twinax(Hebrew) 4F New-437 (Hebrew) 81 New-DIG 850 (Hebr.) 83 Old-Code 860 (Hebr.) 98 Flarro 863 (Hebrew) 99 Table 865 (Hebrew) 9A CP775 Baltic A6 CP1257 Baltic 77 Mazovia (Poland) 92 Kamenicky (Czech) 91 CP866 Ukraine 8F CP866 Kazakhstan 90 51 Tally Dascom 5130P Code Page Tables CP 437 (US) CP 737 Greek 52 Tally Dascom 5130P CP 850 (Multilingual) CP 851 53 Tally Dascom 5130P CP 852 (Eastern Europe) CP 857 (Turkish) 54 Tally Dascom 5130P CP 858 CP 860 (Portugal) 55 Tally Dascom 5130P CP 861 (Iceland) CP 863 (French-Canadian) 56 Tally Dascom 5130P CP 864 Arabic CP 864 Arabic Extended 57 Tally Dascom 5130P CP 865 (Norway) CP 866 (Cyrillic) 58 Tally Dascom 5130P CP 866 Bulgaria CP 1250 Win Latin 2 59 Tally Dascom 5130P CP 1251 Win Cyrillic CP 1252 Win Latin 1 60 Tally Dascom 5130P CP 1253 Win Greek CP 1254 Win Turkish 61 Tally Dascom 5130P 8859-1 Latin 1 8859-1 Latin 1 (SAP) 62 Tally Dascom 5130P ISO 8859-2 (ISO Latin 2) ISO 8859-5 Cyrillic 63 Tally Dascom 5130P ISO 8859-7 (Latin/Greek) ISO 8859-9 (Turkish) 64 Tally Dascom 5130P ISO 8859-15 Euro (Code Page 923) BRASCII 65 Tally Dascom 5130P Abicomp Roman 8 66 Tally Dascom 5130P Coax/Twinax (Hebrew) New-437 (Hebrew) 67 Tally Dascom 5130P New-Dig 850 (Hebrew) Old-Code 860 (Hebrew) 68 Tally Dascom 5130P Flarro 863 (Hebrew) 865 Hebrew 69 Tally Dascom 5130P CP 1257 866 Ukraine 70 Tally Dascom 5130P 866 Kazakhstan Kamenicky 71 Tally Dascom 5130P Mazovia CP 775 72 Tally Dascom 5130P CRO-ASCII Arabic Farsi 73 Tally Dascom 5130P Arabic Urdu Greek DEC 74 Tally Dascom 5130P Greek ELOT 928 75 Tally Dascom 5130P 11 Control Codes Summary Epson Emulation Command List Command Sequence BEL BS HT LF VT FF CR SO SI DC1 DC2 DC3 DC4 CAN DEL ESC SO ESC SI ESC SP n ESC EM n ESC ! n ESC ( - n1 n2 m d1 d2 ESC $ n1 n2 ESC | n ESC % n ESC & ESC ( ^ n m d1 d2… ESC (G NUL d ESC * m n1 n2… ESC . c v h m nL nH d1 d2… ESC + n ESC – n ESC / n ESC ( C NUL n m ESC ( c NUL nt mt nb mb ESC ( U NUL n ESC 0 ESC 2 ESC 3 n ESC 4 ESC 5 ESC 6 ESC 7 Function Beeper Backspace Tab horizontally Line feed Tab vertically Form feed Carriage return Select double-width printing (one line) Select condensedmode Online Cancel condensedmode Offline Cancel double-wide mode(one line) Cancel line Delete character Select double-width printing (one line) Select condensedmode Set intercharacter space NA Print mode setup Choose character lineation Select absolute horizontal print position Set left margin Select user-defined set Define user-defined set Print data in character style Select graphics mode Select imagemode Print raster graphics Select n/360″line spacing Underline on/off Select vertical orientation channel Set page length Page setup Set unit Set 1/8″line spacing Set 1/6″line spacing Set n/180″line spacing Set Italic Cancel Italic Enable printable characters Enable upper control characters 76 Tally Dascom 5130P ESC : ESC < Copy ROM to RAM Unidirectional mode(1 line) ESC > ESC = ESC # ESC ?n m Set MSB to 1 Set MSB to 0 Cancel MSB control Reassign graphics mode ESC @ ESC \n1 n2 Initialize printer Set relative horizontal print position ESC A n ESC B…NUL ESC C n ESC D…NUL ESC E ESC F ESC G ESC H ESC J n ESC K n1 n2 … ESC L n1 n2 … ESC M Set n/60″line spacing Set/cancel vertical tabs Set page length in lines Set/cancel horizontal tabs Select Bold Cancel Bold Select double-strike mode Cancel double-strike mode Perform tactic n/180″line feed Select 8 pins single-density graphics Select 8 pins double–density graphics Select ELITE(12CPI) ESC N n ESC O ESC P Set bottom margin Cancel bottom margin Select PICA(10CPI) ESC Q n ESC R n ESC S n ESC T ESC U n ESC ( V NUL n m ESC W n ESC X n1 n2 ESC Y n1 n2 … ESC Z n1 n2 … ESC a n ESC b n ESC c n m ESC g ESC j n ESC k n ESC p n ESC q n ESC r n ESC t n ESC (t nL nH d1 d2 d3 ESC ( v NUL n m ESC w n ESC x n ESC( B n1 n2 k m s v1 v2 c Set right margin International character set Select superscript/subscript Cancel superscript/subscript Select unidirectional/bidirectional printing mode Select absolute vertical print position Turn Double-wide mode on/off Select font by pitch and point Select 8 pins, high speed ,double–density graphics Select 8 pins, high speed fourfold –density graphics Select justification Select vertical orientation channel Set horizontal intercharacter space Select 15CPI Perform reverse n/180″line feed Select typeface Turn proportional mode on/off Select character style Select printing colour Select character table Assign character table Set relative vertical print position Turn double-high mode on/off Select print quality Barcode print 77 Tally Dascom 5130P IBM Emulation Command List Command Sequence BEL BS HT LF VT FF CR SO SI DC1 DC2 DC3 DC4 CAN ESC BEL ESC BS ESC HT ESC CR ESC LF ESC SO ESC SI ESC DC1 ESC DC2 ESC DC3 ESC DC4 ESC CAN ESC FF ESC EM n ESC : ESC VT ESC 0 ESC 1 ESC 2 ESC 3 n ESC 4 ESC 5 n ESC 6 ESC 7 ESC = ESC \ ESC ^ ESC A n ESC B n ESC C n Function Beeper Backspace Tab horizontally Line feed Tab vertically Form feed Enter Select double-wide mode Select condensedmode Online Select 10CPI Offline Cancel double-wide mode(one line) Cancel buffer Beeper Backspace Tab horizontally Enter Line feed Select double-wide mode Select condensedmode Online Select 10CPI Offline Cancel double-wide mode(one line) Cancel buffer Form feed Automatically Feed Paper mode Set 12CPI Tab vertically Select 1/8″line spacing Select 7/72″line spacing Select 1/6″line spacing or activate ESC A n command Select n/216″or 1/180″line spacing Set top margin Automatic Line Feed Select character set 2 Select character set 1 NA Print continuously from all character chart Print single character from all character chart Select n/72″or n/60″line spacing Select Tab vertically Set page length in lines 78 Tally Dascom 5130P ESC C NUL n ESC D ESC E ESC F ESC G ESC H ESC I n ESC J n ESC K n1 n2 V1 V2 …Vn ESC L n1 n2 V1 V2 …Vn ESC N n ESC O ESC P n ESC Q n ESC R ESC S n ESC T ESC U n ESC W n ESC X n m ESC Y n1 n2 V1 V2 …Vn ESC Z n1 n2 V1 V2 …Vn ESC [- n1 n2 m1 m2 ESC [@ n1 n2 m1 m2 m3 m4 ESC [I n1 n2 Hf Ls Hs Lf Sm NUL Hc Lc ESC [ K n1 n2 init id para1 para2 …paran ESC [ T n1 n2 n3 n4 Hc Lc ESC [\ ESC [d ESC [f n1 n2 k m s v1 v2c ESC [g n1 n2 m ESC [p n1 n2 ESC ] ESC_ n ESC- n ESC d n m ESC j ESC r n ESC * m Set page length in inches Select Tab horizontally Select bold Cancel bold Select double-strike mode Cancel double-strike mode Select printing mode Perform n/180″or n/216″single line feed Normal density graphics Dual-Density Bit Image Graphics (Half Speed) Select bottom margin Cancel bottom margin Set proportional intercharacter Offline Clear tab Select superscript/subscript Cancel superscript/subscript Select bidirectional printing on/off Select double-wide printing mode(continuous) Set left and right margin Select double -density graphics Select fourfold -density graphics Select line Select printing mode Select font and pitch Set initialization condition Set code page Set vertical unit Select printing quality Set barcode parameters Select high-density graphics printing Set barcode data Feed paper in reverse direction Print upper-line Print underline Move the current printing position Stop printing Select printing colour Select graphic mode If you need more details regarding the emulation commands, please contact us. 79 FCC STATEMENT 1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: a. This device may not cause harmful interference. b. This device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Re-orientate or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help DASCOM REPRESENTATIVES GERMANY UNITED KINGDOM RUSSIA and CIS DASCOM Europe GmbH DASCOM GB Ltd DASCOM Europe GmbH Heuweg 3 ViewPoint, Basing View, Representation Moscow D-89079 Ulm Basingstoke, Hampshire Leninsky Prospekt 95a, Office 322 Deutschland RG21 4RG, England 119313 Moscow, Russian Federation Tel.: +49 (0) 731 2075 0 Phone: +44 (0) 1256 481481 Phone: +7 (495) 984 70 65 Fax: +49 (0) 731 2075 100 Fax: +44 (0) 1256 481400 Fax: +7 (495) 984 56 42 www.dascom.com www.dascom.com www.dascom.com SINGAPORE (ASIA PACIFIC) AMERICAS DASCOM AP Pte Ltd DASCOM Americas Corporation 63 Hillview Avenue 421 W. Main Street, Waynesboro, #08-22, Lam Soon Industrial Building VA 22980, USA Singapore 669569 Phone:+1 (877) 434 13 77 Phone: +65 6760 8833 www.dascom.com Fax: +65 6760 1066 www.dascom.com.sg FRANCE CEE DASCOM Europe GmbH DASCOM Europe GmbH 117 Avenue Victor Hugo Europaring F15 301 92100 Boulogne-Billancourt 2345 Brunn a. G. France Austria Phone: +33 (1) 73 02 51 98 Phone: +43 (1) 236 01 70 10 www.dascom.com www.dascom.com “All rights reserved. Translations, reprinting or copying by any means of this manual completeor in part or in any different form requires our explicit approval. We reserve the right to make changes to this manual without notice. All care has been taken to ensure accuracy of information contained in this manual. However, we cannot accept responsibility for any errors or damages resulting from errors or inaccuracies of information herein.” © 2011 DASCOM Part No: 21.511.802.0042_PreTrac-01
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : No Author : hans.scheffler Create Date : 2011:12:13 16:54:20+08:00 Modify Date : 2011:12:13 16:56:28+08:00 Tagged PDF : Yes XMP Toolkit : Adobe XMP Core 4.2.1-c041 52.342996, 2008/05/07-20:48:00 Creator Tool : Acrobat PDFMaker 9.0 Word 版 Metadata Date : 2011:12:13 16:56:28+08:00 Producer : Acrobat Distiller 9.0.0 (Windows) Format : application/pdf Creator : hans.scheffler Title : Microsoft Word - UG 5130T_preliminary_tv04.doc Document ID : uuid:c4656cea-6894-48e1-bfed-39ed2bc05652 Instance ID : uuid:61ab3c57-b580-450f-9858-02a439fba416 Subject : 9 Company : MC SYSTEM Comments : 文件由 Solid Converter PDF v4 建立,版本:4.0 Build 557 Source Modified : D:20111213085159 Page Layout : OneColumn Page Count : 95EXIF Metadata provided by EXIF.tools