Northfield Telecommunications d b a Advanced Wireless Communications AWR391V4 Two-way Radio User Manual AW391 20080812
Northfield Telecommunications, Inc. d/b/a Advanced Wireless Communications Two-way Radio AW391 20080812
User Manual
AWR391V4 Part number S139145702 6-Ganged Charger Model Number: 420855208640 Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help. ISEDC RSS warning This device complies with ISEDC licence-exempt RSS standard (s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'ISEDC applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. The device is authorized to operate at a duty factor not to exceed 50%. SAR tests are conducted using standard operating positions accepted by the FCC/ISEDC warning device transmitting at its highest certified power level in all tested frequency bands, although the SAR is determined at t he highest certified power level, the actual SAR level of the device while operating can be well below the maximum value. Before a new model is a available for sale to the public, it must be tested and certified to the FCC/ISEDC that it does not exceed the exposure limit established by the FCC/ISEDC, tests for each product are performed in positions and locations as required by the FCC/ISEDC. For body worn operation, this device has been tested and meets the FCC/ISEDC RF exposure when used with an accessory designated for this product or when used with an accessory that Contains no metal. To maintaion compliance with the FCC/ISEDC RF exposure guideline,hold the transimitter and antenna at least 2.5 centimeters from your face and speak in a normal voice,with the antenna pointed up and away from the face. le dispositif est autorisée à fonctionner à un facteur de service ne doit pas dépasser 50%. les essais sont effectués à l'aide des positions standard acceptée par la FCC / ISEDC avertisseur transmettant à son plus haut niveau de puissance certifiée conforme à toutes les bandes de fréquences de r - s test, bien que la puissance est déterminée au niveau le plus élevé de recherche et de sauvetage certifié, le niveau de l'appareil en projetg peut être bien en dessous de la valeur maximale.avant qu'un nouveau modèle est disponible pour la vente au public, il doit être testé et certifié à la FCC / ISEDC qu'il ne dépasse pas les limites d'exposition établies par la FCC / ISEDC, tests pour chaque produit sont effectuées dans des postes et des endroits comme requis par la FCC / ISEDC. opération portés sur le corps, ce dispositif a été testé et répond à la FCC / ISEDC l'exposition aux champs rf lorsqu'il est utilisé avec un accessoire désigné pour ce produit ou utilisé avec un accessoire qui ne contient pas de métal. pour maintaion conformité avec la FCC / ISEDC exposition rf transimitter et orientation, l'antenne d'au moins 2,5 cm de ton visage et parlez normalement, avec l'antenne pointée et loin de la tête. TRANSCEIVER RADIO VIEW 10 11 Front View: 0. Antenna Receives and transmits signals 1. LED indicator Lights up red when transmitting a signal 2. Channel Up Press and hold for more than 2.0 seconds to activate the auto scan or dual watch (selected by PC program) for available channel. While radio is on, press button to increase channel no. 3. Channel Down Press and hold for more than 2.0 seconds to activate the key lock.While radio is on, press button to decrease channel no. 4. Speaker Generates audible sound 5. Connection pins Slot pins into a desktop charger docking pins station (docking station not included) 6. Microphone Picks up voice sounds 7. Headset jack Allows use of headset for hands-free communication. 8. Push to talk Press and hold PTT button, speak into the microphone using your normal speaking voice. 9. Volume Up Press and hold more than 1.5 seconds to rapidly increase the volume. While radio is on, press button to increase the volume by a single unit. 10. Volume Down Press and hold for more than 1.5 seconds to rapidly decrease the volume. While radio is on, press button to decrease the volume by a single unit. 11. Power Press and hold for more than 1.5 seconds to turn the unit on or off. Back View: 1. Battery door Remove to access battery compartment 2. Battery compartment Uses lithium 3.7 V - 800 mAh rechargeable battery 3. Mon button Activate MONITOR function LCD DISPLAY SYMBOLS SYMBOL FUNCTION (big) Channel number: Select between 16 channels Dual Watch: Scan 2 channels Battery indicator: Provides battery status during operation High Power˖the current channel is high power Keypad lock: Locks keypad to prevent accidental button activation Auto-scan: Unit is scanning Channels or CTCSS PTT tone: the Call tone is activated VOX: Voice activation system (small) Auxiliary function AWR391V4 AWR391V4 This is no use for AWR391V4. GETTING STARTED INSTALLING / REMOVING / CHARGING THE BATTERY To insert the battery: 1. 2. 3. Slide the battery door open. Insert the lithium battery into the battery compartment, making sure the polarities (+ and –) match. Slide the back cover and clip into place. WARNING: There is a danger in which incorrectly placing the battery can cause an explosion. Always make sure the radio is switched off before installing or changing the battery. Replace only with the same or equipment type. Use ONLY with lithium 3.7V 800mAH rechargeable battery. Contact Advanced Wireless Communications at 1-800-475-5852 or www.adavncedwireless.com for more information. To charge the battery using 6 gang charger: IMPORTANT: Charge the battery for 12 hours on the first charge. After that, it should take 4 or less hours to charge. Make sure the adapter is not obstructed and is easily accessible to the unit. 1) Connect 6 gang charger to AC power using DC adaptor provided. 2) Slide CHG-CLON switch to select CHG. 3) Insert radio unit into 1st docking cradle (insert additional radio units into docking cradles, 2 through 6). Please ensure radio screen faces forward (same direction as LED lights on gang charger). Battery Status Battery charging Extra Batteries LED Battery charged Green Red Radio screen LCD backlight on LCD backlight off NOTE: To completely disconnect from power, the adapter should be disconnected from the 6-Ganged Charger. Batteries should not be exposed to excessive heat such as sunshine or fire. The 6-Ganged Charger and adapter should not be exposed to wet conditions. No objects filled with liquid, such as vases, should be placed on the main unit and adapter. To maintain the battery life of your two-way transceiver it is recommended that you only charge the battery when needed. Overcharging the battery will reduce performance. For best results ensure that the unit is turned off before charging. Remove batteries before storing your radio for extended periods. Batteries corrode over time and may cause permanent damage to your radio. TURN THE UNIT ON / OFF To turn the unit ON or OFF: Press and hold until you hear a beep and the LCD display appears or disappears. VOLUME To change the volume level: Use or to increase or decrease volume. TALK TO ANOTHER TRANSCEIVER For best transmission speak about 2 away from the radio and leave a short pause before speaking once you have pressed To talk to another transceiver: 1. Press and hold “Mon” to check if the channel is free. 2. Press and hold 3. Release once you have finished speaking to allow other radios to respond. The transceiver will automatically play received transmissions. and speak into the microphone to transmit. NOTE: You can only communicate with another transceiver that is on the same channel and using the same CTCSS/DCS code as your transceiver. 7 SCAN / DW FOR A CHANNEL / CTCSS / DCS will be disabled when Scan function is activated. NOTE: or To auto-scan / DW for a channel / CTCSS / DCS: 1. 2. DW or Scan function is selected by PC program. Channel for DW is chosen by PC program. 3. Press and release 4. to enter the Tx mode on the last valid channel in memory and Press continue to scan after the button is released. 5. to terminate the All Scan mode. The radio will then return to the Long press last valid channel. to enter scan mode. NOTE: If you activate a scan while your code is set to off, the radio will check for any activity on each channel, regardless of the code used on that channel. If you activate a scan while the CTCSS or DCS code is set, the radio will only check for activity on the specified channel and code combinations set on your radio. BATTERYSAVER/TXPOWER/PTTTONE SETTING 1. Short press , the LCD will display “S” and flashing “y” or “n”, then press or to enable or disable the Battery Saver mode, when the Battery saver is active, the will be displayed on the LCD screen. 2. Short press or the to toggle the current channel TX power. When the Channel is High power, will be displayed on the LCD screen. 3. Short press or again, the LCD will display “P” and flashing “H” or “L”, Then press again, the LCD will display “t” and flashing “y” or “n”, Then press to enable or disable the PTT tone. When the PTT tone is active, the displayed on the LCD screen will be TROUBLESHOOTING See below for some common problems and their remedies. DO NOT attempt any repairs yourself. This will invalidate your warranty. PROBLEM Can’t turn the radio on Can’t communicate with other radios VOX function is not working POSSIBLE CAUSES / REMEDIES ● ● ● Check the battery is correctly installed and has been fully charged For this and all other issues contact Advanced Wireless Communications at 1-800-475-5852 or www.advancedwireless.com for more information Check the headset is correctly plugged in and is compatible with the Mini 391 radio Package List Accessories Photo Quantity Radio Battery 1 3 1 Charger 4 Power Adapter 1 5 1 Belt Clip 10
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : No Author : dnli Create Date : 2018:06:29 16:38:50+08:00 Modify Date : 2018:07:19 10:10:44-07:00 XMP Toolkit : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26 Producer : Acrobat Distiller 9.0.0 (Windows) Creator Tool : PScript5.dll Version 5.2.2 Metadata Date : 2018:07:19 10:10:44-07:00 Document ID : uuid:d02f52d9-2f77-4062-bdc0-e1a182a72d3c Instance ID : uuid:05fc820d-771c-4cb3-9563-ca6604ea74a3 Format : application/pdf Title : AW391 20080812.cdr Creator : dnli Page Count : 14EXIF Metadata provided by EXIF.tools