Panasonic of North America 96NKX-TGA405 DECT Cordless Telephone Repeater User Manual TGA405 applay ver001 indd
Panasonic Corporation of North America DECT Cordless Telephone Repeater TGA405 applay ver001 indd
user manual
![](/img.php?id=1211748&img=bg1.png)
Installation Guide for Range Extender
By installing this unit, you can extend the range of your phone system, to include
areas where reception was previously not available.
The unit extends the range in all directions, allowing several floors to be covered.
Important:
LThis unit is an accessory unit for use with the following series of Panasonic Digital
Cordless phones: KX-TG4051/KX-TG4071/KX-TG4051C
LThis unit is pre-registered to the base unit.
LThis leaflet only describes the steps needed to install and use the unit. Refer to the
base unit’s operating instructions for the accessory information, important
information for safety, FCC information (for U.S.A. users only), and Industry
Canada Notices and other information (for Canada users only).
For best performance
Placement
LWe recommend installing the unit to a raised position (such as on a wall), which is
well within range of the base unit.
LAvoid positioning the unit close to objects that will interfere with reception, such as
thick walls, radiators, metal shelving, etc.
LFor maximum distance noise-free operation, place the unit away from electrical
appliances such as TV, radio, personal computer or other telephone equipment.
LKeep a minimum distance of 5 m between this unit and the base unit.
(The minimum distance may vary depending on the location.) If the unit is installed
near the base unit, the handset directly communicates with the base unit.
Model No.
Range Extender
KX-TGA405
KX-TGA405C
Base unit
Handset
Range extender
Range extender rangeBase unit range
KX-TG4011/KX-TG4021/KX-TG4031/KX-TG4051/KX-TG4071/KX-TG6511/
KX-TG6521/KX-TG6531/KX-TG6541/KX-TG7531
LYou must register this unit with your base unit before it can be used.
LThis lea et only describes the steps needed to install and use the unit. Please read
the base unit’s operating instructions for further details.
![](/img.php?id=1211748&img=bg2.png)
_2_
Controls
Understanding the STATUS indicator and q indicator
Installation
ASTATUS indicator
Bq indicator
ID indicator
CPROGRAM
Indicator Light status Meaning
STATUS
indicator
Green On LWithin base unit range. The unit is ready for
use.
Flashing L1 handset is communicating with the base
unit through this unit.
Flashing
rapidly
L2 handsets are communicating with the base
unit through this unit.
Red On LOut of base unit range.
Off LThe power is off. (AC adaptor is not
connected properly.)
q
indicator
Green On LSignal strength of the base unit is strong.
Amber On LSignal strength of the base unit is weak.
Red On LOut of base unit range.
Off LThe unit is not being used.
LThe power is off.
B
A
C
1 Base unit:
Press and hold [LOCATOR] for about 5 seconds until the registration tone
sounds.
LThe next step must be completed within 90 seconds.
![](/img.php?id=1211748&img=bg3.png)
_3_
Wall Mounting
Drive the screws (not supplied) into the wall. Mount the unit, then slide it down.
37.0 mm
(1
15
/
32
inches)
Screws
2Confirm that the STATUS indicator and q indicator light green. (The unit is
ready for use.)
LIf the indicators do not light green, re-position the unit in a place where the
indicators light green.
2
1Connect the unit.
LUse only the supplied Panasonic AC adaptor PQLV219.
LWhen the unit is turned on, the STATUS indicator and q indicator light amber
for about 2 seconds.
Press plug firmly.
(120 V AC, 60 Hz)
Hook
2
3
Note:
LThe AC adaptor must remain connected at all times. (It is normal for the adaptor to
feel warm during use.)
LThe unit can support a maximum of 2 handsets at a time.
Specifications
NStandard: DECT 6.0 (Digital Enhanced Cordless Telecommunications 6.0)
NFrequency range: 1.92 GHz to 1.93 GHz
NRF transmission power: 115 mW (max.)
NPower source: 120 V AC, 60 Hz
NPower consumption: Standby: Approx. 0.0 W, Maximum: Approx. 0.0 W
LTo stop the registration tone, press [LOCATOR] on the base unit.
1.0 W, 1.8 W
![](/img.php?id=1211748&img=bg4.png)
_4_
Troubleshooting
Problem Cause/solution
The unit does not work. LWhen the indicators do not light, the AC adaptor is not
connected properly. Check the connections.
LWhen the indicators light red, the unit is out of base
unit range. Move the unit closer to the base unit.
LRegistration may have been canceled.
Deregister the unit, then re-register.
Deregister:
1Unplug the AC adaptor, then press and hold
{PROGRAM}.
2While pressing and holding {PROGRAM},
re-connect the AC adaptor.
3Keep pressing and holding {PROGRAM} for about
10 seconds until the STATUS indicator flashes
amber. Then release {PROGRAM}.
Re-register:
1Range extender: Unplug the AC adaptor.
2Base unit: Press and hold {LOCATOR} for about
5 seconds until the registration tone sounds.
– The next step must be completed within 90
seconds.
3Range extender: Connect the AC adaptor, then
wait until the STATUS indicator lights green.
4Base unit: To stop the registration tone, press
{LOCATOR}.
While talking using the
handset, sound cuts in
and out.
LThe handset is out of range. Move the handset closer
to this unit.
![](/img.php?id=1211748&img=bg5.png)
_5_
For your safety
To prevent severe injury and loss of life/
property, read this section carefully before
using the product to ensure proper and safe
operation of your product.
WARNING
Power connection
LUse only the power source marked on the
product.
LDo not overload power outlets and
extension cords. This can result in the risk
of fire or electric shock.
LCompletely insert the AC adaptor/power
plug into the power outlet. Failure to do so
may cause electric shock and/or excessive
heat resulting in a fire.
LRegularly remove any dust, etc. from the
AC adaptor/power plug by pulling it from the
power outlet, then wiping with a dry cloth.
Accumulated dust may cause an insulation
defect from moisture, etc. resulting in a fire.
LUnplug the product from power outlets if it
emits smoke, an abnormal smell, or makes
an unusual noise. These conditions can
cause fire or electric shock. Confirm that
smoke has stopped emitting and contact
the Panasonic Call Center at 1-800-211-
PANA (1-800-211-7262).
LUnplug from power outlets and never touch
the inside of the product if its casing has
been broken open.
LNever touch the plug with wet hands.
Danger of electric shock exists.
Installation
LTo prevent the risk of fire or electrical shock,
do not expose the product to rain or any
type of moisture.
LDo not place or use this product near
automatically controlled devices such as
automatic doors and fire alarms. Radio
waves emitted from this product may cause
such devices to malfunction resulting in an
accident.
LDo not allow the AC adaptor or telephone
line cord to be excessively pulled, bent or
placed under heavy objects.
Operating safeguards
LUnplug the product from power outlets
before cleaning. Do not use liquid or
aerosol cleaners.
LDo not disassemble the product.
LDo not spill liquids (detergents, cleansers,
etc.) onto the telephone line cord plug, or
allow it to become wet at all. This may
cause a fire. If the telephone line cord plug
becomes wet, immediately pull it from the
telephone wall jack, and do not use.
Medical
LConsult the manufacturer of any personal
medical devices, such as pacemakers or
hearing aids, to determine if they are
adequately shielded from external RF
(radio frequency) energy. (The product
operates in the frequency range of 1.92
GHz to 1.93 GHz, and the RF transmission
power is 115 mW (max.).)
LDo not use the product in health care
facilities if any regulations posted in the
area instruct you not to do so. Hospitals or
health care facilities may be using
equipment that could be sensitive to
external RF energy.
CAUTION
Installation and location
LNever install telephone wiring during an
electrical storm.
LNever install telephone line jacks in wet
locations unless the jack is specifically
designed for wet locations.
LNever touch uninsulated telephone wires or
terminals unless the telephone line has
been disconnected at the network interface.
LUse caution when installing or modifying
telephone lines.
LThe AC adaptor is used as the main
disconnect device. Ensure that the AC
outlet is installed near the product and is
easily accessible.
LThis product is unable to make calls when:
– the handset batteries need recharging or
have failed.
– there is a power failure.
・ The AC adaptor is used as the main
disconnected device. Ensure that the AC
outlet is installed near the product and is
easily accessible.
![](/img.php?id=1211748&img=bg6.png)
_6_
Important safety
instructions
When using your product, basic safety
precautions should always be followed to
reduce the risk of fire, electric shock, and
injury to persons, including the following:
1. Do not use this product near water for
example, near a bathtub, washbowl,
kitchen sink, or laundry tub, in a wet
basement or near a swimming pool.
2. Avoid using a telephone (other than a
cordless type) during an electrical storm.
There may be a remote risk of electric
shock from lightning.
3. Do not use the telephone to report a gas
leak in the vicinity of the leak.
4. Use only the power cord and batteries
indicated in this manual. Do not dispose of
batteries in a fire. They may explode.
Check with local codes for possible special
disposal instructions.
SAVE THESE INSTRUCTIONS
For best performance
Base unit location/avoiding noise
The base unit and other compatible Panasonic
units use radio waves to communicate with
each other.
LFor maximum coverage and noise-free
communications, place your base unit:
– at a convenient, high, and central
location with no obstructions between
the handset and base unit in an indoor
environment.
– away from electronic appliances such as
TVs, radios, personal computers,
wireless devices, or other phones.
– facing away from radio frequency
transmitters, such as external antennas
of mobile phone cell stations. (Avoid
putting the base unit on a bay window or
near a window.)
LCoverage and voice quality depends on the
local environmental conditions.
LIf the reception for a base unit location is not
satisfactory, move the base unit to another
location for better reception.
Range extender location/avoiding noise
The range extender and other compatible
Panasonic units use radio waves to
communicate with each other.
Environment
LKeep the product away from electrical noise
generating devices, such as fluorescent
lamps and motors.
LThe product should be kept free from
excessive smoke, dust, high temperature,
and vibration.
LThe product should not be exposed to direct
sunlight.
LDo not place heavy objects on top of the
product.
LWhen you leave the product unused for a
long period of time, unplug the product from
the power outlet.
LThe product should be kept away from heat
sources such as heaters, kitchen stoves,
etc. It should not be placed in rooms where
the temperature is less than 0 °C (32 °F) or
greater than 40 °C (104 °F). Damp
basements should also be avoided.
LThe maximum calling distance may be
shortened when the product is used in the
following places: Near obstacles such as
hills, tunnels, underground, near metal
objects such as wire fences, etc.
LOperating the product near electrical
appliances may cause interference. Move
away from the electrical appliances.
Routine care
LWipe the outer surface of the product
with a soft moist cloth.
LDo not use benzine, thinner, or any
abrasive powder.
![](/img.php?id=1211748&img=bg7.png)
_7_
Other information
CAUTION: Risk of explosion if battery is
replaced by an incorrect type. Dispose of used
batteries according to the instructions.
Notice for product disposal, transfer, or
return
LThis product can store your private/
confidential information. To protect your
privacy/confidentiality, we recommend that
you erase information such as phonebook
or caller list entries from the memory before
you dispose of, transfer, or return the
product.
Notice
Important safety
instructions
FCC and other
information
This device complies with Part 15 of the
FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful
interference, and (2) this device must
accept any interference received, including
interference that may cause undesired
operation.
Privacy of communications may not be
ensured when using this phone.
CAUTION:
Any changes or modifications not expressl
y
approved by the party responsible for
compliance could void the user’s authority
to operate this device.
NOTE:
This equipment has been tested and found
to comply with the limits for a Class B digit
a
device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provid
e
reasonable protection against harmful
interference in a residential installation. Thi
s
equipment generates, uses, and can radiat
e
radio frequency energy and, if not installed
and used in accordance with the
instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that
interference will not occur in a particular
installation. If this equipment does cause
harmful interference to radio or television
reception, which can be determined by
turning the equipment off and on, the user i
encouraged to try to correct the interferenc
e
by one or more of the following measures:
– Reorient or relocate the receiving
antenna.
– Increase the separation between the
equipment and receiver.
– Connect the equipment into an outlet on a
circuit different from that to which the
receiver is connected.
![](/img.php?id=1211748&img=bg8.png)
_8_
– Consult the dealer or an experienced
radio/TV technician for help.
Some cordless telephones operate at
frequencies that may cause interference to
nearby TVs and VCRs. To minimize or
prevent such interference, the base of the
cordless telephone should not be placed
near or on top of a TV or VCR. If
interference is experienced, move the
cordless telephone further away from the TV
or VCR. This will often reduce, or eliminate,
interference.
FCC RF Exposure Warning:
L This product complies with FCC radiation
exposure limits set forth for an
uncontrolled environment.
L To comply with FCC RF exposure
requirements, the base unit must be
installed and operated 20 cm (8 inches)
or more between the product and all
person’s body (excluding extremities of
hands, wrist and feet).
L This product may not be collocated or
operated in conjunction with any other
antenna or transmitter.
L The handset may be carried and operated
with only the specific provided belt-clip.
Other non-tested belt-clips or similar
body-worn accessories may not comply
and must be avoided.
Notice
L FCC ID can be found inside the battery
compartment or on the bottom of the
units.
FCC ID can be found on the bottom of the unit.
To comply with FCC RF exposure
requirements, the range extender must be
installed and operated 20 cm (8 inches) or more
between the product and all person’s body
(excluding extremities of hands, wrist and feet).