SES imagotag APG2-USB1-A digital network controller device User Manual
SES-imagotag GmbH digital network controller device
User Manual
Document Title Goes Here Test setup and specification for certification tests Description This page describes the quick-start with a per-defined test setup and how-to run tests with this setup. FCC: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the authority to operate the equipment. IC: This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement. Pr-requisites Network cable Local machine (laptop/PC) Ethernet interface Administration rights (to change the network settings) JAVA Runtime Environment (JRE), Version 8 or higher Test setup components Core appliance 32GB - ID 52675 - 05CAB002303-I200000720 ESL Dongle - ID 50400 AP-2010 - ID TBA USB pen drive incl. "Control Center" software Initial test setup preparation Prepare local machine 1. Change your Ethernet adapter settings 2. Control Panel - Network Connections 3. Right click on the desired Ethernet interface and select "Properties" Page 1 Document Title Goes Here a. 4. Select "Internet Protocol Version 4 (TCP/IPv4)" and click "Properties" 5. Use the following IP address and subnet mask a. IP address: 192.168.1.30 b. Subnet mask: 255.255.255.0 c. Prepare core appliance, ESL dongle and/or AP-2010 1. Unpack components a. Unpack core appliance, power supply and ESL dongle. Page 2 Document Title Goes Here 1. b. 2. Connect components a. Network cable Ethernet port "1" & Ethernet port of your laptop or PC b. Power jack Power socket "DC+12V" c. ESL Dongle USB port "1" Page 3 Document Title Goes Here d. 3. Power core appliance Power switch "ON" 4. Copy the following folder from the USB pen drive to your local computer: "Control_Center" a. Example local directory: "C:\ses-imagotag\" b. c. Make sure that JAVA is installed on your local machine. (e.g.: Open a windows command prompt and execute "java -version" command) Page 4 Document Title Goes Here d. 5. Create shortcut with "client.jar" a. 6. Rename shortcut to "Control Center - 192.168.1.10" 7. Edit shortcut with right click "Properties" 8. Add " --host 192.168.1.10" after "client.jar" as target link and apply the changes Page 5 Document Title Goes Here a. 9. Rename the shortcut to "client.jar - 192.168.1.10" a. 10. Execute the shortcut and use the following username/password combination to login: a. Username: admin b. Password: admin 11. Wait until the "Control Center" window opens Page 6 Document Title Goes Here a. Your system's now ready to start working with labels (register, send images, switch pages, ...) Your current ESL channel is 10 (ESL dongle LED is blue) Working with labels You'll find information about working with labels in the "Core Service Quick Start Guide" 10.1 Register labels 11.2 Sending images to labels Sources: https://portal.imagotag.com/get/documentation https://portal.imagotag.com/files/all/docs/it_quick-start-guide_en.pdf Example images The USB stick contains a collection of test images that can be sent to the labels. Operate the system with an AP-2010 This section describes how to change the operation from an ESL dongle to an AP-2010. 1. Unplug the ESL dongle 2. Delete the configuration of AP-ID "50400" via Control Center: "System Access Point Configuration" Page 7 Document Title Goes Here a. 3. Connect the Ethernet interface of the AP-2010 with the Ethernet port 2 of the core appliance a. Use the included network cable b. 4. Plug in the power supply of the access point 5. Wait until the AP-2010's LED turns blue 6. Check the Access Point status via Control Center: "System Access Point Status" Page 8 Document Title Goes Here a. Change back to the operation with ESL dongle This section describes how to change the operation from an AP-2010 to an ESL dongle 1. Switch off the AP-2010 a. http://192.168.1.20/admin/shutdownReboot.xml Execute "Shutdown Access Point" b. Wait until the LED turns RED c. Plug out power supply 2. Turn off the core appliance a. http://192.168.1.10/admin/shutdown.xml b. Execute "Shutdown Device" c. d. Wait for the device to shut down (LEDs off) e. Power switch "OFF" 3. Plugin the ESL dongle to USB port "1" 4. Turn on core appliance Power switch "ON" 5. Add the configuration for the ESL dongle with ID "50400" via Control Center: "System Access Point Configuration" Page 9 5. Document Title Goes Here a. b. Fill "Access Point ID" with "50400" and c. "Host" with "localhost" d. Submit changes by "Save" e. 6. Wait until the ESL dongle's LED turns blue 7. Check the Access Point status via Control Center: "System Access Point Status" a. AP-2010 is "OFFLINE" b. ESL dongle is "ONLINE" Page 10 Document Title Goes Here c. Operate EMC Test 1. 2. 3. 4. 5. Take the prepared Sample with the channel you want to evaluate (CH 0, 4, 10) Prepare the prepared counterpart with the same channel you chose (CH 0,4, 10) Plug-in the power supply of the counterpart and put in the batteries of the EUT The AP and the Label now start automatically to permanently exchange packets If the transmission is OK, the LED will remain OFF. If a transmission fails the LED will be ON until the next successful transmission of data. 6. You can check the functionality if a you unplug the counterpart The LED of the EUT should light up within 2 seconds. Modulated/Unmodulated Output test 1. Take the EUT and put in the batteries 2. the label will send continuosly with maximum output power 3. You can start all required measurements for the certification report Page 11
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No Modify Date : 2018:10:17 14:21:53Z Create Date : 2018:10:17 14:21:53Z Producer : iText 2.1.7 by 1T3XT Page Mode : UseOutlines Page Count : 11EXIF Metadata provided by EXIF.tools