SSV Works MRB3 MRB3 Wired Remote and Black Box User Manual
SSV Works, Inc MRB3 Wired Remote and Black Box
User Manual
RADIO FUNCTIONS Selecting FM/AM Band: Press MODE until the FM or AM band shows on the display. Automatic Station Search: Press stops when a station is found. or to start automatic station search. The search or until M - SEEK. Press the or Manual Station Search: Press and hold briefly to change the frequency until the desired frequency is set. Change to Automatic search (A - SEEK) mode after a station is found. User Guide BLUETOOTH AUDIO STREAMING 1. Open the Bluetooth setup program on the mobile device and activate the Bluetooth feature 2. The device will show up as “SSV”. Select this device and enter passkey: OOOO 3. After successfully pairing, a Bluetooth logo will appear on the phone menu screen and show “CONNECT” “BT MUSIC” on the device LCD display. Stop Playback: Press Skip Track: Press briefly to pause music. Press or MRB3 button again to continue playback. to play previous/next song. CONNECTING AN EXTERNAL AUDIO DEVICE (OPTIONAL) - Press MODE until AUX shows on the display. Line in Add 3.5mm AUX-in and USB Charging with SSV Works 3PUSB35A (sold separately) MRB3 Bluetooth® Media Controller WARRANTY INFORMATION: All SSV Works enclosures are covered by a limited lifetime warranty against defects in material or workmanship. All SSV Works Electronics are covered by a limited 1 year warranty against defects in material or workmanship. Labor for replacement of defective components is not covered. All SSV Works Speakers are covered by a limited 1 year warranty against defects in material or workmanship. Contact SSV Works for further warranty information. Corporate: SSV WORKS, 201 N. Rice Ave Unit A, Oxnard, CA 93030 Web: www.SSVworks.com | Phone: 818-991-1778 | Fax: 866-293-6751 The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG,Inc. and any use of such marks by SSV Works is under license. © 2016 SSV Works, Oxnard, CA 93030 MRB3 Rev. B 3-22-16 SAFETY INFORMATION Do not attempt to disassemble or repair the MRB3 yourself. Please call SSV Works for technical assistance or repair information. Changes or modifications to the MRB3 not authorized by SSV Works will void the warranty. SSV Works recommends disconnecting the negative battery terminal before beginning any installation. AMPLIFIER WIRING DIAGRAM BUTTON LOCATIONS AND FUNCTIONS 1. Play/Pause Power On/Off Mute 12v+ Yellow MRB3 2. Volume Up/Down 3. Mode 4. Track Forward/Back Station Forward/Back Menu Settings Up/Down USB 1A charge input does not read USB data Signal ground (Black) AMP turn on (Blue) 5. LCD Display GENERAL OPERATIONS Power On/Off: Press to power on. Press and hold to power off. Volume: Press the VOL(+) or (-) button to increase or decrease the volume. Mute On/Off: Press briefly to mute the sound. Press again to un-mute the sound. Mode Sources: Press the MODE button to switch between AUX, FM, AM, Bluetooth (BT MUSIC). Mode Settings (Bass/Treble/Balance/Fader/EQ/Loudness): Press the MODE button for 2 seconds and then press the button until the function you want is shown on the display. Press VOL(+) (-) to change the settings of the menu item displayed. 2 sec. MODE BASS TRE BAL FAD EQ LOUD Bass (BAS)/Treble (TRE): Press the VOL(+) or (-) button to adjust Bass & Treble. Balance (BAL): Press VOL(+) or (-) to adjust balance (sound distribution between the right and left speakers). Fader (FAD): Press VOL(+) or (-) to adjust sound distribution between the front and rear speakers. Equalizer (EQ): Press VOL(+) or (-) to select one of the EQ options: OFF, FLAT, CLASS, POP, ROCK, JAZZ, METAL. The equalizer will be disabled if EQ OFF is set. The equalizer setting is shown at the bottom of the display. Loudness (LOUD): Press VOL(+) or (-) (LOUD ON) or to disable the function (LOUD OFF). When the loudness function is on, LOUD is shown on the right of the display. Technical speci ications TUNER FM Frequency Range Channel Step Sensitivity Stereo Separation Signal to Noise Ratio 87.5-107.9 MHz 200 kHz 2.8 μV 30 dB 50 dB FCC Caution This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : Yes Create Date : 2016:03:22 12:40:06-07:00 Creator : Adobe InDesign CC 2015 (Windows) Modify Date : 2016:05:13 14:27:24+08:00 Has XFA : No Language : en-US XMP Toolkit : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03 Metadata Date : 2016:05:13 14:27:24+08:00 Creator Tool : Adobe InDesign CC 2015 (Windows) Instance ID : uuid:43d286d8-a6a8-49c4-9ce7-af46a532564f Original Document ID : xmp.did:2c613c15-4b08-6b4f-8f35-d30e59f0dd17 Document ID : xmp.id:0a1f289f-d977-e04c-a824-4782ff42954a Rendition Class : proof:pdf Derived From Instance ID : xmp.iid:faf03d08-adde-4642-86b7-a9afa2ddcd4e Derived From Document ID : xmp.did:e89fa051-3e14-2549-90c2-d2acdc456d65 Derived From Original Document ID: xmp.did:2c613c15-4b08-6b4f-8f35-d30e59f0dd17 Derived From Rendition Class : default History Action : converted History Parameters : from application/x-indesign to application/pdf History Software Agent : Adobe InDesign CC 2015 (Windows) History Changed : / History When : 2016:03:22 12:40:06-07:00 Format : application/pdf Producer : Adobe PDF Library 15.0 Trapped : False Page Count : 3EXIF Metadata provided by EXIF.tools