SZ DJI TECHNOLOGY WM334R1801 Phantom 4 RTK User Manual Phantom 4 RTK EN 20180205
SZ DJI TECHNOLOGY CO., LTD Phantom 4 RTK Phantom 4 RTK EN 20180205
Contents
- 1. User Manual
- 2. Users Manual
User Manual
Phantom 4 RTK Quick Stark Guide V1.0 Phantom 4 RTK PHANTOMTM 4 RTK is equipped with 4 directions of obstacle avoidance allowing it to intelligently avoid obstacles during flight. Return‐to‐Home function and stable hover and flight indoors are also available.The aircraft has a built‐in DJITM Onboard D‐RTK*, which provideshigh‐precision data for centimeter‐level positioning to realize more accurate mapping operation.The camera uses a 1‐inchCMOS sensor offering unprecedented clarity, lower noise, and better quality images to enhance aerial imaging for mapping. The maps generated through the mapping image data can be used for field planning of the Agras MG‐1S Advanced or MG‐1P series. 1. Gimbal and Camera 9. Motors 2. Downward Vision System 10. Propellers 3. Micro USB Port 11. Aircraft Status Indicators 4. Camera/Linking Status 12. Antennas Indicatorand Link Button 13. Onboard D‐RTK Antenna 5. Camera Micro SD Card Slot 14. Rear Vision System 6. Forward Vision System 15. Intelligent Flight Battery 7. Infrared Sensing System 16. Power Button 8. Front LEDs 17. Battery Level Indicators * This should be used with a DJI Base Station (purchased additionally) or DJI approved Network RTK service. Remote Controller The powerful remote controller of the Phantom 4 RTK has a transmission range extending up to 4.3 mi (7 km)*. It features physical buttons and dials to control camera tilt, photo capture and video recording. Built into the remote controller is DJIOCUSYNCTM, providing a live HD view from the Phantom camera directly on the display. Dual frequency support makes the HD video downlink more stable. Replaceable batteries and antennas of the remote controller make it easy for daily operation and maintenance. 1 Antennas 10 Battery Level LEDs 19Pause Button 2Display Device 11 Micro SD Card Slot 20 Camera Settings Dial 3 Speaker 12 RTH Status LED 21 C1Button (customizable) 4 Control Sticks 13 RTH Button 22 C2Button (customizable) 5 Lanyard Attachment 14 Gimbal Dial 23 Battery Compartment Cover 6Power Button 15 Record Button 24Battery Compartment Cover Lock 7 Status LED 16 Flight Mode Switch 25Remote Controller Back Cover 8 USB‐CPort 17 Sleep/Wake Button 9 3.5 mmAudio Port 18 Shutter Button The default flight control is known as Mode 2. The left stick controls the aircraft’s altitude and heading, while the rightstick controls its forward, backward, left and right movements. The gimbal dial controls the camera’s tilt. *The remote controller is able to reach its maximum transmission distance (FCC) in a wide openarea with no Electro‐Magnetic Interference, and at an altitude of about 400 feet (120 meters). Using Phantom 4 RTK 1. Mount the Remote Controller Battery An external changeable Intelligent Battery is used for the remote controller, which is convenient for long‐term operation. Slide the Battery Compartment Cover Lock on back of the remote controller. Then mount the Intelligent Battery into the compartment and push it to the top position. Finally, close the cover. Battery Release Button Press and hold the Battery Release Button and push the battery down to remove it from the compartment. 2. Check the Battery Levels Low→ High Low→ High Press once to check the battery level. Press once, then again and hold to turn on/off. 3. Charge the Batteries Power Outlet 100~240 V ●Make sure to fully charge the batteries in first‐time use. 4. Prepare the Remote Controller Unfold Strong Weak 5. Prepare for Take off DJI MG APP Remove the gimbal clamp from the camera. Power on the remote controller and the Launch DJI MG, complete the first‐time setup, and enter Operation View. Black propeller rings go on motors with black dots. Silver propeller rings go on motors without black dots. Press the propeller down onto the mounting plate and rotate in the lock direction until secure. ●Check that the propellers are secure before each flight. 6. Flight Before taking off, make sure the Aircraft Status Bar in the DJI MG app indicates ‘Ready to Go (GPS)’. Takeoff OR Combination Stick Command to start/stop the motors Landing Left stick up (slowly) to take off Left stick down (slowly) until you touch the ground Hold a few seconds to stop the motors Stop motor mid‐flight ●Rotating propellers can be dangerous. Do not start the motors when there are people nearby. ● Always keep your hands on the remote controller so long as the motor is still spinning. ● Stop motor mid‐flight: Pull the left stick to the bottom inside corner while simultaneously pressing the RTH button. Only stop motors mid‐flight in emergency situations when doing so can reduce the risk of damage or injury. 7. Mapping Plan the mapping area in the DJI MG app, and then resume the task to generate a map with more accurate positioning. Users can finish field planning on the new map and share the planning to the remote controller of the Agras MG ‐1S Advanced orMG‐1P series to achieve more accurate and efficient route planning. a. DJI MG AppMain Interface>Field Plan>Plan with P4 RTK>Start. b. Tap the screen at the boundary point of the area that requires mapping to add a waypoint. c. Tap and hold the screen to mark an obstacle. d. Add calibration point: Walk to the location of the calibration point. Tad Add Calibration Point onscreen. e. Parameter settings: Set Flying Speed, Altitude, Front Overlap Ration, Side Overlap Ration. f. Save and name the task. g. Go to DJI MG Main Interface > Resume Task > Task List on the left > Mapping to choose and resume a mapping task. h. Rectify position. i. Slide to start the task. j. The app will generate a map after the task is completed. Users can choose the map in Field tag of the Task List. k. Add waypoints and obstacle information on the generated map for field plan. The planning data will be saved in the current field task. l. Share the field task to DJI Agriculture Service app. Then the related users can download it from the remote controller of the Agras MG‐1S Advanced or MG‐1P series to generate route quickly and perform a route task. Specifications ●Aircraft Weight (Battery & Propellers Included) Max Service Ceiling Above Sea Level Max Flight Time 1388 g 6000 m Approx. 30 minutes Operating Temperature ●Gimbal Controllable ●Vision System Velocity Range Altitude Range Operating Range Obstacle Sensory Range Operating Environment ●Infrared Sensing System Obstacle Sensory Range Operating Environment ●Camera Sensor Lens ISO Range Max Image Size Supported File Systems Supported SD Cards Operating Temperature ●Remote Controller Operating Temperature Operating Voltage Built‐in Display Device 32° to 104° F ( 0° to 40° C) ‐90° to +30° 31 mph (50 kph) at 6.6 ft (2 m) above ground 0 ‐ 33 ft (0 ‐ 10 m) 0 ‐ 33 ft (0 ‐ 10 m) 2 ‐ 98 ft (0.7 ‐ 30 m) Surfaces with clear patterns and adequate lighting (> 15 lux) 0.6 ‐ 23 ft (0.2 ‐ 7 m) Surface with diffuse reflection material, and reflectivity > 8% (such as wall, trees, humans, etc.) 1’’ CMOS; Effective pixels: 20M FOV (Field of View) 84°, 24 mm (35 mm format equivalent) f/2.8 ‐ f/11. auto focus at 1 m ‐ ∞ 100 ‐ 3200 (Auto) 16:9 Aspect Ratio: 5472×3078 FAT32 ( 32 GB); exFAT (> 32 GB) Micro SD, Max Capacity: 128 GB. Class 10 or UHS‐1 rating required 32° to 104° F ( 0° to 40° C) 32° to 104° F ( 0° to 40° C) 1.2 A @ 7.4 V Android system, 5.5 inch screen, 1920×1080, 1000 cd/m2, 4G RAM + 16G ROM ●Remote Controller Intelligent Battery (WB37‐4920mAh‐7.6V) Battery Type LiPo battery Capacity 4920 mAh Voltage 7.6 V Energy 37.39 Wh Charging Temperature 5° to 40°C (41° to 104°F) ●Intelligent Flight Battery (PH4‐5870mAh‐15.2V) Capacity Voltage Battery Type Energy Net Weight Charging Temperature Range Max Charging Power ●Charging Hub(WCH2) Input Voltage Output Voltage and Current Operating Temperature ●AC Power Adapter (A14‐057N1A) Voltage Rated Power 5870 mAh 15.2 V LiPo 4S 89.2 Wh 468 g 14° to 104° F (‐10° to 40° C) 100 W 17.3 ‐ 26.2 V 8.7 V, 6 A; 5 V, 2 A 5° to 40°C (41° to 104°F) 17.4 V 100 W Compliance Information FCC ComplianceNotice This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help. RF Exposure Information For aircraft,it complies wi th FCC radiation exposure limits setforth for an uncontrolled environment. In order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the antenna shall not be less than 20cm during normal operation. For Remote Controller, SAR tests are conducted using standard operating positions accepted by the FCC with the remote controller transmitting at its highest certified power level in all tested frequency bands, although the SAR is determined at the highest certified power level, the actual SAR level of the remote controller while operating can be well below the maximum value value. Before a new model is a available for sale to the public, it must be tested and certified to the FCC that it does not exceed the exposure limit established by the FCC Tests for each model are performed in positions and locations as required by the FCC . For body worn operation, this mobile phone has been tested and meets the FCC RF exposure guidelines when used with an accessory designated for this product or when used with an accessory that contains no metal and that positions the handset a minimum of 10 mm from the body. KCC Warning Message “해당무선설비는운용중전파혼신가능성이있으므로인명안전과관련된서비스는할수없습니다.” “해당무선설비는운용중전파혼신가능성이있음” EU Compliance Statement: SZ DJI TECHNOLOGY CO., LTD hereby declares that this device is in compliance with the essential requirements and other relevant provisions of the Directive 2014/53/EU. A copy of the EU Declaration of Conformity is available online atwww.dji.com/euro‐compliance EU contact address: DJI GmbH, Industriestrasse. 12, 97618, Niederlauer, Germany Declaración de cumplimiento UE: SZ DJI TECHNOLOGY CO., LTD por la presente declara que este dispositivo cumple los requisitos básicos y el resto de provisiones relevantes de la Directiva 2014/53/EU. Hay disponible online una copia de la Declaración de conformidad UE enwww.dji.com/euro‐compliance Dirección de contacto de la UE: DJI GmbH, Industriestrasse. 12, 97618, Niederlauer, Germany EU‐verklaring van overeenstemming: SZ DJI TECHNOLOGY CO., LTD verklaart hierbij dat dit apparaat voldoet aan de essentiële vereisten en andere relevante bepalingen van Richtlijn 2014/53/EU. De EU‐verklaring van overeenstemming is online beschikbaar op www.dji.com/euro‐compliance Contactadres EU: DJI GmbH, Industriestrasse. 12, 97618, Niederlauer, Germany ormidade da UE: A SZ DJI TECHNOLOG GY CO., LTD declara, atravvés deste doccumento, Declaraçção de confo que estee dispositivo está em conformidade co om os requisitos essenciaais e outras d disposições re elevantes da Diretiva 2014/53//EU. online uma cóp pia da Declaração de confformidade da UE disponível Existe w.dji.com/eurro‐compliancee emwww Industriestrasse. 12, 1 97618, Nieederlauer, Geermany Endereçço de contacto na UE: DJI GmbH, nformità UE:: SZ DJI TECH HNOLOGY CO O., LTD, dichiara che il presente dispositivo è Dichiaraazione di con conform me ai requisiti essenziali e alle altre disp posizioni rilevvanti della dirrettiva 2014/5 53/EU. Una copia della dichiaraziione di conformità UE è disponibile online all'indirizzo Webww ww.dji.com/eu uro‐compliance Indirizzzo di contattto UE: DJI Gm mbH, Industrie estrasse. 12, 97618, Niedeerlauer, Germ many ente, SZ DJI TECHNOLOGY Y CO., LTD décclare que Déclaaration de conformité UE : Par la prése pareil est conforme aux principales exigences et autres clauses pertineentes de la directive cet app européeenne 2014/53 3/EU. Une cop pie de la déclaaration de conformité UE est disponible sur le sitew www.dji.com//euro‐compliaance l'UE : DJII GmbH, Indu ustriestrasse. 12, 97618, Niederlauer, G Germany Adresse de contact pour mpliance: Hieermit erklärt SZ DJI TECH HNOLOGY CO O., LTD, dasss dieses Gerrät den wese entlichen EU‐Com einschlägigen Bestimmungen der EU‐Richttlinie 2014/53 Anforderungen und anderen 3/EU entspriccht. pie der EU‐Ko onformitätserrklärung findeen Sie online auf www.dji..com/euro‐co ompliance. Eine Kop Kontaktaadresse innerrhalb der EU:: DJI GmbH, Industriestrassse. 12, 97618 8, Niederlaueer, Germany N: RISK OFF EXPLOSION N IF BATTEERY IS REPLLACED BY AN A INCORRECT TYPE. DISPOSE CAUTION OF USED D BATTERIES ACCORDING T THE INSTR TO RUCTIONS Environmentally friendly disposal Old electrical appliances must not be disposed of together with the residual waste, but have to be disposed of separately. The disposal at the communal collecting point via private persons is for free. The owner of old appliances is responsible to bring the appliances to these collecting points or to similar collection points. With this little personal effort, you contribute to recycle valuable raw materials and the treatment of toxic substances.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : No Author : DG06139 Create Date : 2018:02:12 14:21:48+08:00 Modify Date : 2018:04:09 18:08:04-07:00 XMP Toolkit : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26 Creator Tool : PScript5.dll Version 5.2.2 Metadata Date : 2018:04:09 18:08:04-07:00 Producer : Acrobat Distiller 9.0.0 (Windows) Format : application/pdf Title : Microsoft Word - Phantom 4 RTK-EN 20180205 Creator : DG06139 Document ID : uuid:11babe23-3916-4a62-b1ee-8cd785bc1e68 Instance ID : uuid:e39f7068-5f72-4eca-a9c9-d164a1abf791 Page Count : 10EXIF Metadata provided by EXIF.tools